[
  {
    "sku": "7300",
    "brand": "GENERIC-ISO",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 35,
    "B_mm": 11,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 50,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7300-series (ISO 15 diameter series 3) the last two digits encode the bore: 7300 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 35 mm and width 11 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6300 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 10 mm shaft, specify a j5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "fans and blowers",
      "hand tool rotors",
      "small precision gearboxes",
      "instrument spindles"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 7300 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04.",
      "The 73xx medium section gains axial and radial rating at 10 mm bore through a 35 mm OD and 11 mm width; the heavier balls also trade away speed versus a 7200 angular contact.",
      "Angular-contact 7300 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 7300 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7300 angular-contact bearing?",
        "a": "A 7300 single-row angular-contact ball bearing has a 10 mm bore, 35 mm outer diameter and 11 mm width (0.394 × 1.378 × 0.433 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 50 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "Why does 7300 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 7300 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What is the contact angle of 7300?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7300 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7300 compare with a deep-groove 6300?",
        "a": "Both share the 10×35×11 mm ISO 15 envelope (12.5 mm radial section), but the angular-contact 7300 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6300."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7300-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7300",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7000",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 26,
    "B_mm": 8,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 18,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7000 carries bore code 00 = 10 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 26 mm and width 8 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6000 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 10 mm shaft, specify a j5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "small precision gearboxes",
      "instrument spindles",
      "miniature pump rotors",
      "servo drive shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 7000 fits a 10 mm shaft — the code × 5 mnemonic does not apply below code 04.",
      "The 70xx extra-light section at 10 mm bore uses a 26 mm OD; axial capacity is lower than a 7200, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "A single 7000 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7000 angular-contact bearing?",
        "a": "A 7000 single-row angular-contact ball bearing has a 10 mm bore, 26 mm outer diameter and 8 mm width (0.394 × 1.024 × 0.315 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 18 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "Why does 7000 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 7000 with code 00 has a 10 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What is the contact angle of 7000?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7000 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7000 compare with a deep-groove 6000?",
        "a": "Both share the 10×26×8 mm ISO 15 envelope (8.0 mm radial section), but the angular-contact 7000 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6000."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7000-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7000",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7001",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 28,
    "B_mm": 8,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 21,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7001 carries bore code 01 = 12 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 28 mm and width 8 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6001 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 12 mm shaft, specify a j5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "instrument spindles",
      "miniature pump rotors",
      "servo drive shafts",
      "fans and blowers"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 7001 fits a 12 mm shaft — the code × 5 mnemonic does not apply below code 04.",
      "The 70xx extra-light section at 12 mm bore uses a 28 mm OD; axial capacity is lower than a 7201, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 7001 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7001 angular-contact bearing?",
        "a": "A 7001 single-row angular-contact ball bearing has a 12 mm bore, 28 mm outer diameter and 8 mm width (0.472 × 1.102 × 0.315 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 21 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "Why does 7001 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 7001 with code 01 has a 12 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What is the contact angle of 7001?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7001 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7001 compare with a deep-groove 6001?",
        "a": "Both share the 12×28×8 mm ISO 15 envelope (8.0 mm radial section), but the angular-contact 7001 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6001."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7001-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7001",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7002",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 32,
    "B_mm": 9,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 29,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7002 carries bore code 02 = 15 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 32 mm and width 9 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6002 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 15 mm shaft, specify a j5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "miniature pump rotors",
      "servo drive shafts",
      "fans and blowers",
      "hand tool rotors"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 7002 fits a 15 mm shaft — the code × 5 mnemonic does not apply below code 04.",
      "The 70xx extra-light section at 15 mm bore uses a 32 mm OD; axial capacity is lower than a 7202, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Angular-contact 7002 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 7002 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7002 angular-contact bearing?",
        "a": "A 7002 single-row angular-contact ball bearing has a 15 mm bore, 32 mm outer diameter and 9 mm width (0.591 × 1.26 × 0.354 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 29 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "Why does 7002 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 7002 with code 02 has a 15 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What is the contact angle of 7002?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7002 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7002 compare with a deep-groove 6002?",
        "a": "Both share the 15×32×9 mm ISO 15 envelope (8.5 mm radial section), but the angular-contact 7002 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6002."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7002-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7002",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7003",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 35,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 38,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7003 carries bore code 03 = 17 mm. Codes 00–03 follow the 10/12/15/17 mm exception table rather than code × 5. Outside diameter 35 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6003 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 17 mm shaft, specify a j5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "servo drive shafts",
      "fans and blowers",
      "hand tool rotors",
      "small precision gearboxes"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Bore codes 00–03 use the exception table: 7003 fits a 17 mm shaft — the code × 5 mnemonic does not apply below code 04.",
      "The 70xx extra-light section at 17 mm bore uses a 35 mm OD; axial capacity is lower than a 7203, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Preload class matters: a 7003 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7003 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7003 angular-contact bearing?",
        "a": "A 7003 single-row angular-contact ball bearing has a 17 mm bore, 35 mm outer diameter and 10 mm width (0.669 × 1.378 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 38 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "Why does 7003 not follow the bore-code × 5 rule?",
        "a": "Codes 00–03 use the exception table (10, 12, 15 and 17 mm): 7003 with code 03 has a 17 mm bore. The code × 5 convention starts at code 04 (20 mm)."
      },
      {
        "q": "What is the contact angle of 7003?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7003 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7003 compare with a deep-groove 6003?",
        "a": "Both share the 17×35×10 mm ISO 15 envelope (9.0 mm radial section), but the angular-contact 7003 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6003."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7003-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7003",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7004",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 42,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 66,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7004 carries bore code 04 = 20 mm. Outside diameter 42 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6004 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 20 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "electric motor shafts",
      "conveyor head pulleys",
      "pump and compressor shafts",
      "small machine tool spindles"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "At a 20 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 70xx extra-light section at 20 mm bore uses a 42 mm OD; axial capacity is lower than a 7204, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7004 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 7004 where a deep-groove 6004 would do: same 20×42×12 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7004 angular-contact bearing?",
        "a": "A 7004 single-row angular-contact ball bearing has a 20 mm bore, 42 mm outer diameter and 12 mm width (0.787 × 1.654 × 0.472 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 66 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7004 bore code work?",
        "a": "The last two digits of 7004 are bore code 04, giving 04 × 5 = 20 mm bore. The 42 mm outside diameter and 12 mm width follow the ISO 15 diameter series, shared with the 6004 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7004?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7004 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7004 compare with a deep-groove 6004?",
        "a": "Both share the 20×42×12 mm ISO 15 envelope (11.0 mm radial section), but the angular-contact 7004 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6004."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7004-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7004",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7005",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 47,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 76,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7005 carries bore code 05 = 25 mm. Outside diameter 47 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6005 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 25 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "conveyor head pulleys",
      "pump and compressor shafts",
      "small machine tool spindles",
      "servo and stepper drives"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "At a 25 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 70xx extra-light section at 25 mm bore uses a 47 mm OD; axial capacity is lower than a 7205, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Do not run a single 7005 where a deep-groove 6005 would do: same 25×47×12 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 12 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7005 angular-contact bearing?",
        "a": "A 7005 single-row angular-contact ball bearing has a 25 mm bore, 47 mm outer diameter and 12 mm width (0.984 × 1.85 × 0.472 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 76 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7005 bore code work?",
        "a": "The last two digits of 7005 are bore code 05, giving 05 × 5 = 25 mm bore. The 47 mm outside diameter and 12 mm width follow the ISO 15 diameter series, shared with the 6005 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7005?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7005 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7005 compare with a deep-groove 6005?",
        "a": "Both share the 25×47×12 mm ISO 15 envelope (11.0 mm radial section), but the angular-contact 7005 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6005."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7005-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7005",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7006",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 55,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 111,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7006 carries bore code 06 = 30 mm. Outside diameter 55 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6006 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 30 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "pump and compressor shafts",
      "small machine tool spindles",
      "servo and stepper drives",
      "gear reducers"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "At a 30 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 70xx extra-light section at 30 mm bore uses a 55 mm OD; axial capacity is lower than a 7206, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Shaft and housing fillets must clear the bearing chamfer so the 13 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7006 angular-contact bearing?",
        "a": "A 7006 single-row angular-contact ball bearing has a 30 mm bore, 55 mm outer diameter and 13 mm width (1.181 × 2.165 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 111 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7006 bore code work?",
        "a": "The last two digits of 7006 are bore code 06, giving 06 × 5 = 30 mm bore. The 55 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 6006 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7006?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7006 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7006 compare with a deep-groove 6006?",
        "a": "Both share the 30×55×13 mm ISO 15 envelope (12.5 mm radial section), but the angular-contact 7006 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6006."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7006-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7006",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7007",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 62,
    "B_mm": 14,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 147,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7007 carries bore code 07 = 35 mm. Outside diameter 62 mm and width 14 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6007 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 35 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "small machine tool spindles",
      "servo and stepper drives",
      "gear reducers",
      "electric motor shafts"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "At a 35 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 70xx extra-light section at 35 mm bore uses a 62 mm OD; axial capacity is lower than a 7207, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 7007 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7007 angular-contact bearing?",
        "a": "A 7007 single-row angular-contact ball bearing has a 35 mm bore, 62 mm outer diameter and 14 mm width (1.378 × 2.441 × 0.551 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 147 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7007 bore code work?",
        "a": "The last two digits of 7007 are bore code 07, giving 07 × 5 = 35 mm bore. The 62 mm outside diameter and 14 mm width follow the ISO 15 diameter series, shared with the 6007 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7007?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7007 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7007 compare with a deep-groove 6007?",
        "a": "Both share the 35×62×14 mm ISO 15 envelope (13.5 mm radial section), but the angular-contact 7007 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6007."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7007-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7007",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7008",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 68,
    "B_mm": 15,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 182,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7008 carries bore code 08 = 40 mm. Outside diameter 68 mm and width 15 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6008 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 40 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "servo and stepper drives",
      "gear reducers",
      "electric motor shafts",
      "conveyor head pulleys"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "At a 40 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 70xx extra-light section at 40 mm bore uses a 68 mm OD; axial capacity is lower than a 7208, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "A single 7008 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7008 angular-contact bearing?",
        "a": "A 7008 single-row angular-contact ball bearing has a 40 mm bore, 68 mm outer diameter and 15 mm width (1.575 × 2.677 × 0.591 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 182 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7008 bore code work?",
        "a": "The last two digits of 7008 are bore code 08, giving 08 × 5 = 40 mm bore. The 68 mm outside diameter and 15 mm width follow the ISO 15 diameter series, shared with the 6008 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7008?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7008 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7008 compare with a deep-groove 6008?",
        "a": "Both share the 40×68×15 mm ISO 15 envelope (14.0 mm radial section), but the angular-contact 7008 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6008."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7008-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7008",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7009",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 75,
    "B_mm": 16,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 231,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7009 carries bore code 09 = 45 mm. Outside diameter 75 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6009 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 45 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "gear reducers",
      "electric motor shafts",
      "conveyor head pulleys",
      "pump and compressor shafts"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "At a 45 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 70xx extra-light section at 45 mm bore uses a 75 mm OD; axial capacity is lower than a 7209, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 7009 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7009 angular-contact bearing?",
        "a": "A 7009 single-row angular-contact ball bearing has a 45 mm bore, 75 mm outer diameter and 16 mm width (1.772 × 2.953 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 231 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7009 bore code work?",
        "a": "The last two digits of 7009 are bore code 09, giving 09 × 5 = 45 mm bore. The 75 mm outside diameter and 16 mm width follow the ISO 15 diameter series, shared with the 6009 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7009?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7009 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7009 compare with a deep-groove 6009?",
        "a": "Both share the 45×75×16 mm ISO 15 envelope (15.0 mm radial section), but the angular-contact 7009 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6009."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7009-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7009",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7010",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 80,
    "B_mm": 16,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 250,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7010 carries bore code 10 = 50 mm. Outside diameter 80 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6010 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 50 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "printing and textile machinery",
      "medium motor drives",
      "machine tool spindles",
      "centrifugal pumps"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Thermal expansion on this 50 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 70xx extra-light section at 50 mm bore uses a 80 mm OD; axial capacity is lower than a 7210, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Angular-contact 7010 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 7010 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7010 angular-contact bearing?",
        "a": "A 7010 single-row angular-contact ball bearing has a 50 mm bore, 80 mm outer diameter and 16 mm width (1.969 × 3.15 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 250 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7010 bore code work?",
        "a": "The last two digits of 7010 are bore code 10, giving 10 × 5 = 50 mm bore. The 80 mm outside diameter and 16 mm width follow the ISO 15 diameter series, shared with the 6010 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7010?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7010 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7010 compare with a deep-groove 6010?",
        "a": "Both share the 50×80×16 mm ISO 15 envelope (15.0 mm radial section), but the angular-contact 7010 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6010."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7010-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7010",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7011",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 90,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 366,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7011 carries bore code 11 = 55 mm. Outside diameter 90 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6011 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 55 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medium motor drives",
      "machine tool spindles",
      "centrifugal pumps",
      "industrial compressors"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Thermal expansion on this 55 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 70xx extra-light section at 55 mm bore uses a 90 mm OD; axial capacity is lower than a 7211, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Preload class matters: a 7011 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7011 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7011 angular-contact bearing?",
        "a": "A 7011 single-row angular-contact ball bearing has a 55 mm bore, 90 mm outer diameter and 18 mm width (2.165 × 3.543 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 366 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7011 bore code work?",
        "a": "The last two digits of 7011 are bore code 11, giving 11 × 5 = 55 mm bore. The 90 mm outside diameter and 18 mm width follow the ISO 15 diameter series, shared with the 6011 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7011?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7011 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7011 compare with a deep-groove 6011?",
        "a": "Both share the 55×90×18 mm ISO 15 envelope (17.5 mm radial section), but the angular-contact 7011 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6011."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7011-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7011",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7012",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 95,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 391,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7012 carries bore code 12 = 60 mm. Outside diameter 95 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6012 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 60 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "machine tool spindles",
      "centrifugal pumps",
      "industrial compressors",
      "gearbox output shafts"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "Thermal expansion on this 60 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 70xx extra-light section at 60 mm bore uses a 95 mm OD; axial capacity is lower than a 7212, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7012 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 7012 where a deep-groove 6012 would do: same 60×95×18 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7012 angular-contact bearing?",
        "a": "A 7012 single-row angular-contact ball bearing has a 60 mm bore, 95 mm outer diameter and 18 mm width (2.362 × 3.74 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 391 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7012 bore code work?",
        "a": "The last two digits of 7012 are bore code 12, giving 12 × 5 = 60 mm bore. The 95 mm outside diameter and 18 mm width follow the ISO 15 diameter series, shared with the 6012 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7012?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7012 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7012 compare with a deep-groove 6012?",
        "a": "Both share the 60×95×18 mm ISO 15 envelope (17.5 mm radial section), but the angular-contact 7012 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6012."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7012-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7012",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7013",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 100,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 417,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7013 carries bore code 13 = 65 mm. Outside diameter 100 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6013 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 65 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "centrifugal pumps",
      "industrial compressors",
      "gearbox output shafts",
      "printing and textile machinery"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "Thermal expansion on this 65 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 70xx extra-light section at 65 mm bore uses a 100 mm OD; axial capacity is lower than a 7213, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Do not run a single 7013 where a deep-groove 6013 would do: same 65×100×18 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 18 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7013 angular-contact bearing?",
        "a": "A 7013 single-row angular-contact ball bearing has a 65 mm bore, 100 mm outer diameter and 18 mm width (2.559 × 3.937 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 417 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7013 bore code work?",
        "a": "The last two digits of 7013 are bore code 13, giving 13 × 5 = 65 mm bore. The 100 mm outside diameter and 18 mm width follow the ISO 15 diameter series, shared with the 6013 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7013?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7013 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7013 compare with a deep-groove 6013?",
        "a": "Both share the 65×100×18 mm ISO 15 envelope (17.5 mm radial section), but the angular-contact 7013 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6013."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7013-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7013",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7014",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 110,
    "B_mm": 20,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 577,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7014 carries bore code 14 = 70 mm. Outside diameter 110 mm and width 20 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6014 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 70 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "industrial compressors",
      "gearbox output shafts",
      "printing and textile machinery",
      "medium motor drives"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Thermal expansion on this 70 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 70xx extra-light section at 70 mm bore uses a 110 mm OD; axial capacity is lower than a 7214, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Shaft and housing fillets must clear the bearing chamfer so the 20 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7014 angular-contact bearing?",
        "a": "A 7014 single-row angular-contact ball bearing has a 70 mm bore, 110 mm outer diameter and 20 mm width (2.756 × 4.331 × 0.787 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 577 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7014 bore code work?",
        "a": "The last two digits of 7014 are bore code 14, giving 14 × 5 = 70 mm bore. The 110 mm outside diameter and 20 mm width follow the ISO 15 diameter series, shared with the 6014 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7014?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7014 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7014 compare with a deep-groove 6014?",
        "a": "Both share the 70×110×20 mm ISO 15 envelope (20.0 mm radial section), but the angular-contact 7014 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6014."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7014-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7014",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7015",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 115,
    "B_mm": 20,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 609,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7015 carries bore code 15 = 75 mm. Outside diameter 115 mm and width 20 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6015 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 75 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "gearbox output shafts",
      "printing and textile machinery",
      "medium motor drives",
      "machine tool spindles"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "Thermal expansion on this 75 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 70xx extra-light section at 75 mm bore uses a 115 mm OD; axial capacity is lower than a 7215, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 7015 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7015 angular-contact bearing?",
        "a": "A 7015 single-row angular-contact ball bearing has a 75 mm bore, 115 mm outer diameter and 20 mm width (2.953 × 4.528 × 0.787 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 609 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7015 bore code work?",
        "a": "The last two digits of 7015 are bore code 15, giving 15 × 5 = 75 mm bore. The 115 mm outside diameter and 20 mm width follow the ISO 15 diameter series, shared with the 6015 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7015?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7015 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7015 compare with a deep-groove 6015?",
        "a": "Both share the 75×115×20 mm ISO 15 envelope (20.0 mm radial section), but the angular-contact 7015 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6015."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7015-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7015",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7016",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 125,
    "B_mm": 22,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 813,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7016 carries bore code 16 = 80 mm. Outside diameter 125 mm and width 22 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6016 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 80 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "cement and mining drives",
      "power transmission shafts",
      "heavy machine tool spindles",
      "large gearboxes and reducers"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "Mount this 80 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 80 mm bore uses a 125 mm OD; axial capacity is lower than a 7216, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "A single 7016 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7016 angular-contact bearing?",
        "a": "A 7016 single-row angular-contact ball bearing has a 80 mm bore, 125 mm outer diameter and 22 mm width (3.15 × 4.921 × 0.866 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 813 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7016 bore code work?",
        "a": "The last two digits of 7016 are bore code 16, giving 16 × 5 = 80 mm bore. The 125 mm outside diameter and 22 mm width follow the ISO 15 diameter series, shared with the 6016 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7016?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7016 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7016 compare with a deep-groove 6016?",
        "a": "Both share the 80×125×22 mm ISO 15 envelope (22.5 mm radial section), but the angular-contact 7016 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6016."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7016-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7016",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7017",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 130,
    "B_mm": 22,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 853,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7017 carries bore code 17 = 85 mm. Outside diameter 130 mm and width 22 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6017 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 85 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "power transmission shafts",
      "heavy machine tool spindles",
      "large gearboxes and reducers",
      "mill and crane drives"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "Mount this 85 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 85 mm bore uses a 130 mm OD; axial capacity is lower than a 7217, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 7017 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7017 angular-contact bearing?",
        "a": "A 7017 single-row angular-contact ball bearing has a 85 mm bore, 130 mm outer diameter and 22 mm width (3.346 × 5.118 × 0.866 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 853 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7017 bore code work?",
        "a": "The last two digits of 7017 are bore code 17, giving 17 × 5 = 85 mm bore. The 130 mm outside diameter and 22 mm width follow the ISO 15 diameter series, shared with the 6017 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7017?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7017 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7017 compare with a deep-groove 6017?",
        "a": "Both share the 85×130×22 mm ISO 15 envelope (22.5 mm radial section), but the angular-contact 7017 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6017."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7017-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7017",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7018",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 140,
    "B_mm": 24,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1106,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7018 carries bore code 18 = 90 mm. Outside diameter 140 mm and width 24 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6018 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 90 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "heavy machine tool spindles",
      "large gearboxes and reducers",
      "mill and crane drives",
      "pulp and paper machinery"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 90 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 90 mm bore uses a 140 mm OD; axial capacity is lower than a 7218, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Angular-contact 7018 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 7018 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7018 angular-contact bearing?",
        "a": "A 7018 single-row angular-contact ball bearing has a 90 mm bore, 140 mm outer diameter and 24 mm width (3.543 × 5.512 × 0.945 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1106 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7018 bore code work?",
        "a": "The last two digits of 7018 are bore code 18, giving 18 × 5 = 90 mm bore. The 140 mm outside diameter and 24 mm width follow the ISO 15 diameter series, shared with the 6018 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7018?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7018 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7018 compare with a deep-groove 6018?",
        "a": "Both share the 90×140×24 mm ISO 15 envelope (25.0 mm radial section), but the angular-contact 7018 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6018."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7018-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7018",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7019",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 145,
    "B_mm": 24,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1154,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7019 carries bore code 19 = 95 mm. Outside diameter 145 mm and width 24 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6019 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 95 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "large gearboxes and reducers",
      "mill and crane drives",
      "pulp and paper machinery",
      "cement and mining drives"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount this 95 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 95 mm bore uses a 145 mm OD; axial capacity is lower than a 7219, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Preload class matters: a 7019 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7019 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7019 angular-contact bearing?",
        "a": "A 7019 single-row angular-contact ball bearing has a 95 mm bore, 145 mm outer diameter and 24 mm width (3.74 × 5.709 × 0.945 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1154 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7019 bore code work?",
        "a": "The last two digits of 7019 are bore code 19, giving 19 × 5 = 95 mm bore. The 145 mm outside diameter and 24 mm width follow the ISO 15 diameter series, shared with the 6019 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7019?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7019 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7019 compare with a deep-groove 6019?",
        "a": "Both share the 95×145×24 mm ISO 15 envelope (25.0 mm radial section), but the angular-contact 7019 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6019."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7019-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7019",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7020",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 150,
    "B_mm": 24,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1202,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7020 carries bore code 20 = 100 mm. Outside diameter 150 mm and width 24 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6020 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 100 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "mill and crane drives",
      "pulp and paper machinery",
      "cement and mining drives",
      "power transmission shafts"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "Mount this 100 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 100 mm bore uses a 150 mm OD; axial capacity is lower than a 7220, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7020 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 7020 where a deep-groove 6020 would do: same 100×150×24 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7020 angular-contact bearing?",
        "a": "A 7020 single-row angular-contact ball bearing has a 100 mm bore, 150 mm outer diameter and 24 mm width (3.937 × 5.906 × 0.945 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1202 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7020 bore code work?",
        "a": "The last two digits of 7020 are bore code 20, giving 20 × 5 = 100 mm bore. The 150 mm outside diameter and 24 mm width follow the ISO 15 diameter series, shared with the 6020 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7020?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7020 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7020 compare with a deep-groove 6020?",
        "a": "Both share the 100×150×24 mm ISO 15 envelope (25.0 mm radial section), but the angular-contact 7020 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6020."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7020-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7020",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7021",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 160,
    "B_mm": 26,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1519,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7021 carries bore code 21 = 105 mm. Outside diameter 160 mm and width 26 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6021 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 105 mm shaft, specify a m6 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "pulp and paper machinery",
      "cement and mining drives",
      "power transmission shafts",
      "heavy machine tool spindles"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "Mount this 105 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 105 mm bore uses a 160 mm OD; axial capacity is lower than a 7221, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Do not run a single 7021 where a deep-groove 6021 would do: same 105×160×26 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 26 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7021 angular-contact bearing?",
        "a": "A 7021 single-row angular-contact ball bearing has a 105 mm bore, 160 mm outer diameter and 26 mm width (4.134 × 6.299 × 1.024 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1519 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7021 bore code work?",
        "a": "The last two digits of 7021 are bore code 21, giving 21 × 5 = 105 mm bore. The 160 mm outside diameter and 26 mm width follow the ISO 15 diameter series, shared with the 6021 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7021?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7021 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7021 compare with a deep-groove 6021?",
        "a": "Both share the 105×160×26 mm ISO 15 envelope (27.5 mm radial section), but the angular-contact 7021 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6021."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7021-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7021",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7022",
    "brand": "GENERIC-ISO",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 170,
    "B_mm": 28,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1885,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7000-series (ISO 15 diameter series 0) the last two digits encode the bore: 7022 carries bore code 22 = 110 mm. Outside diameter 170 mm and width 28 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6022 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 110 mm shaft, specify a m6 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "cement and mining drives",
      "power transmission shafts",
      "heavy machine tool spindles",
      "large gearboxes and reducers"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Mount this 110 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 70xx extra-light section at 110 mm bore uses a 170 mm OD; axial capacity is lower than a 7222, so do not substitute a failed 72-series spindle bearing with a 70 without re-rating the thrust.",
      "Shaft and housing fillets must clear the bearing chamfer so the 28 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7022 angular-contact bearing?",
        "a": "A 7022 single-row angular-contact ball bearing has a 110 mm bore, 170 mm outer diameter and 28 mm width (4.331 × 6.693 × 1.102 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1885 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7022 bore code work?",
        "a": "The last two digits of 7022 are bore code 22, giving 22 × 5 = 110 mm bore. The 170 mm outside diameter and 28 mm width follow the ISO 15 diameter series, shared with the 6022 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7022?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7022 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7022 compare with a deep-groove 6022?",
        "a": "Both share the 110×170×28 mm ISO 15 envelope (30.0 mm radial section), but the angular-contact 7022 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6022."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7022-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7022",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7404",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 72,
    "B_mm": 19,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 364,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7404 carries bore code 04 = 20 mm. Outside diameter 72 mm and width 19 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6404 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 20 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "electric motor shafts",
      "conveyor head pulleys",
      "pump and compressor shafts",
      "small machine tool spindles"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "At a 20 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 74xx heavy section at 20 mm bore (72 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 7404 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7404 angular-contact bearing?",
        "a": "A 7404 single-row angular-contact ball bearing has a 20 mm bore, 72 mm outer diameter and 19 mm width (0.787 × 2.835 × 0.748 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 364 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7404 bore code work?",
        "a": "The last two digits of 7404 are bore code 04, giving 04 × 5 = 20 mm bore. The 72 mm outside diameter and 19 mm width follow the ISO 15 diameter series, shared with the 6404 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7404?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7404 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7404 compare with a deep-groove 6404?",
        "a": "Both share the 20×72×19 mm ISO 15 envelope (26.0 mm radial section), but the angular-contact 7404 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6404."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7404",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7405",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 80,
    "B_mm": 21,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 486,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7405 carries bore code 05 = 25 mm. Outside diameter 80 mm and width 21 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6405 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 25 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "conveyor head pulleys",
      "pump and compressor shafts",
      "small machine tool spindles",
      "servo and stepper drives"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "At a 25 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 74xx heavy section at 25 mm bore (80 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "A single 7405 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7405 angular-contact bearing?",
        "a": "A 7405 single-row angular-contact ball bearing has a 25 mm bore, 80 mm outer diameter and 21 mm width (0.984 × 3.15 × 0.827 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 486 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7405 bore code work?",
        "a": "The last two digits of 7405 are bore code 05, giving 05 × 5 = 25 mm bore. The 80 mm outside diameter and 21 mm width follow the ISO 15 diameter series, shared with the 6405 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7405?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7405 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7405 compare with a deep-groove 6405?",
        "a": "Both share the 25×80×21 mm ISO 15 envelope (27.5 mm radial section), but the angular-contact 7405 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6405."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7405",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7406",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 90,
    "B_mm": 23,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 664,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7406 carries bore code 06 = 30 mm. Outside diameter 90 mm and width 23 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6406 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 30 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "pump and compressor shafts",
      "small machine tool spindles",
      "servo and stepper drives",
      "gear reducers"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "At a 30 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 74xx heavy section at 30 mm bore (90 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 7406 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7406 angular-contact bearing?",
        "a": "A 7406 single-row angular-contact ball bearing has a 30 mm bore, 90 mm outer diameter and 23 mm width (1.181 × 3.543 × 0.906 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 664 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7406 bore code work?",
        "a": "The last two digits of 7406 are bore code 06, giving 06 × 5 = 30 mm bore. The 90 mm outside diameter and 23 mm width follow the ISO 15 diameter series, shared with the 6406 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7406?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7406 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7406 compare with a deep-groove 6406?",
        "a": "Both share the 30×90×23 mm ISO 15 envelope (30.0 mm radial section), but the angular-contact 7406 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6406."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7406",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7407",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 100,
    "B_mm": 25,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 879,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7407 carries bore code 07 = 35 mm. Outside diameter 100 mm and width 25 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6407 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 35 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "small machine tool spindles",
      "servo and stepper drives",
      "gear reducers",
      "electric motor shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "At a 35 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 74xx heavy section at 35 mm bore (100 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Angular-contact 7407 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 7407 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7407 angular-contact bearing?",
        "a": "A 7407 single-row angular-contact ball bearing has a 35 mm bore, 100 mm outer diameter and 25 mm width (1.378 × 3.937 × 0.984 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 879 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7407 bore code work?",
        "a": "The last two digits of 7407 are bore code 07, giving 07 × 5 = 35 mm bore. The 100 mm outside diameter and 25 mm width follow the ISO 15 diameter series, shared with the 6407 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7407?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7407 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7407 compare with a deep-groove 6407?",
        "a": "Both share the 35×100×25 mm ISO 15 envelope (32.5 mm radial section), but the angular-contact 7407 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6407."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7407",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7408",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 110,
    "B_mm": 27,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1136,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7408 carries bore code 08 = 40 mm. Outside diameter 110 mm and width 27 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6408 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 40 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "servo and stepper drives",
      "gear reducers",
      "electric motor shafts",
      "conveyor head pulleys"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "At a 40 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 74xx heavy section at 40 mm bore (110 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Preload class matters: a 7408 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7408 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7408 angular-contact bearing?",
        "a": "A 7408 single-row angular-contact ball bearing has a 40 mm bore, 110 mm outer diameter and 27 mm width (1.575 × 4.331 × 1.063 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1136 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7408 bore code work?",
        "a": "The last two digits of 7408 are bore code 08, giving 08 × 5 = 40 mm bore. The 110 mm outside diameter and 27 mm width follow the ISO 15 diameter series, shared with the 6408 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7408?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7408 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7408 compare with a deep-groove 6408?",
        "a": "Both share the 40×110×27 mm ISO 15 envelope (35.0 mm radial section), but the angular-contact 7408 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6408."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7408",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7409",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 120,
    "B_mm": 29,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1438,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7409 carries bore code 09 = 45 mm. Outside diameter 120 mm and width 29 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6409 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 45 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "gear reducers",
      "electric motor shafts",
      "conveyor head pulleys",
      "pump and compressor shafts"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 45 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 74xx heavy section at 45 mm bore (120 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 7409 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 7409 where a deep-groove 6409 would do: same 45×120×29 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7409 angular-contact bearing?",
        "a": "A 7409 single-row angular-contact ball bearing has a 45 mm bore, 120 mm outer diameter and 29 mm width (1.772 × 4.724 × 1.142 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1438 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7409 bore code work?",
        "a": "The last two digits of 7409 are bore code 09, giving 09 × 5 = 45 mm bore. The 120 mm outside diameter and 29 mm width follow the ISO 15 diameter series, shared with the 6409 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7409?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7409 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7409 compare with a deep-groove 6409?",
        "a": "Both share the 45×120×29 mm ISO 15 envelope (37.5 mm radial section), but the angular-contact 7409 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6409."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7409",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7410",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 130,
    "B_mm": 31,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 1789,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7410 carries bore code 10 = 50 mm. Outside diameter 130 mm and width 31 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6410 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 50 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "printing and textile machinery",
      "medium motor drives",
      "machine tool spindles",
      "centrifugal pumps"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Thermal expansion on this 50 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 74xx heavy section at 50 mm bore (130 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Do not run a single 7410 where a deep-groove 6410 would do: same 50×130×31 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 31 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7410 angular-contact bearing?",
        "a": "A 7410 single-row angular-contact ball bearing has a 50 mm bore, 130 mm outer diameter and 31 mm width (1.969 × 5.118 × 1.22 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 1789 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7410 bore code work?",
        "a": "The last two digits of 7410 are bore code 10, giving 10 × 5 = 50 mm bore. The 130 mm outside diameter and 31 mm width follow the ISO 15 diameter series, shared with the 6410 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7410?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7410 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7410 compare with a deep-groove 6410?",
        "a": "Both share the 50×130×31 mm ISO 15 envelope (40.0 mm radial section), but the angular-contact 7410 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6410."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7410",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7411",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 140,
    "B_mm": 33,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 2192,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7411 carries bore code 11 = 55 mm. Outside diameter 140 mm and width 33 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6411 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 55 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medium motor drives",
      "machine tool spindles",
      "centrifugal pumps",
      "industrial compressors"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "Thermal expansion on this 55 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 74xx heavy section at 55 mm bore (140 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Shaft and housing fillets must clear the bearing chamfer so the 33 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7411 angular-contact bearing?",
        "a": "A 7411 single-row angular-contact ball bearing has a 55 mm bore, 140 mm outer diameter and 33 mm width (2.165 × 5.512 × 1.299 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 2192 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7411 bore code work?",
        "a": "The last two digits of 7411 are bore code 11, giving 11 × 5 = 55 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, shared with the 6411 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7411?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7411 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7411 compare with a deep-groove 6411?",
        "a": "Both share the 55×140×33 mm ISO 15 envelope (42.5 mm radial section), but the angular-contact 7411 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6411."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7411",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7412",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 150,
    "B_mm": 35,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 2651,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7412 carries bore code 12 = 60 mm. Outside diameter 150 mm and width 35 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6412 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 60 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "machine tool spindles",
      "centrifugal pumps",
      "industrial compressors",
      "gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "Thermal expansion on this 60 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 74xx heavy section at 60 mm bore (150 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 7412 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7412 angular-contact bearing?",
        "a": "A 7412 single-row angular-contact ball bearing has a 60 mm bore, 150 mm outer diameter and 35 mm width (2.362 × 5.906 × 1.378 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 2651 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7412 bore code work?",
        "a": "The last two digits of 7412 are bore code 12, giving 12 × 5 = 60 mm bore. The 150 mm outside diameter and 35 mm width follow the ISO 15 diameter series, shared with the 6412 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7412?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7412 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7412 compare with a deep-groove 6412?",
        "a": "Both share the 60×150×35 mm ISO 15 envelope (45.0 mm radial section), but the angular-contact 7412 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6412."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7412",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7413",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 160,
    "B_mm": 37,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 3169,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7413 carries bore code 13 = 65 mm. Outside diameter 160 mm and width 37 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6413 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 65 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "centrifugal pumps",
      "industrial compressors",
      "gearbox output shafts",
      "printing and textile machinery"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Thermal expansion on this 65 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 74xx heavy section at 65 mm bore (160 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "A single 7413 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7413 angular-contact bearing?",
        "a": "A 7413 single-row angular-contact ball bearing has a 65 mm bore, 160 mm outer diameter and 37 mm width (2.559 × 6.299 × 1.457 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 3169 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7413 bore code work?",
        "a": "The last two digits of 7413 are bore code 13, giving 13 × 5 = 65 mm bore. The 160 mm outside diameter and 37 mm width follow the ISO 15 diameter series, shared with the 6413 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7413?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7413 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7413 compare with a deep-groove 6413?",
        "a": "Both share the 65×160×37 mm ISO 15 envelope (47.5 mm radial section), but the angular-contact 7413 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6413."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7413",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7414",
    "brand": "GENERIC-ISO",
    "series": "7400-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 180,
    "B_mm": 42,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 4629,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 7400-series (ISO 15 diameter series 4) the last two digits encode the bore: 7414 carries bore code 14 = 70 mm. Outside diameter 180 mm and width 42 mm come from the ISO 15 boundary-dimensions general plan, shared with the 6414 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 70 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "industrial compressors",
      "gearbox output shafts",
      "printing and textile machinery",
      "medium motor drives"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "Thermal expansion on this 70 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 74xx heavy section at 70 mm bore (180 mm OD) is built for high combined load at lower speed; specifying it in a high-rpm spindle gives excess heat and short grease life — use 72/73 there.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 7414 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 7414 angular-contact bearing?",
        "a": "A 7414 single-row angular-contact ball bearing has a 70 mm bore, 180 mm outer diameter and 42 mm width (2.756 × 7.087 × 1.654 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 4629 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 7414 bore code work?",
        "a": "The last two digits of 7414 are bore code 14, giving 14 × 5 = 70 mm bore. The 180 mm outside diameter and 42 mm width follow the ISO 15 diameter series, shared with the 6414 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 7414?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 7414 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How does 7414 compare with a deep-groove 6414?",
        "a": "Both share the 70×180×42 mm ISO 15 envelope (55.0 mm radial section), but the angular-contact 7414 has an asymmetric raceway and 40° contact angle: it carries higher combined axial+radial load and runs with controlled preload, but is slower, noisier and needs pairing — it is not a drop-in replacement for a deep-groove 6414."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7414",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71804",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 32,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 18,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71804 carries bore code 04 = 20 mm. Outside diameter 32 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61804 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 20 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "At a 20 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 718xx thin section at 20 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7204.",
      "With a 6.0 mm radial section on a 20 mm bore, the 71804 ring has little stiffness of its own: it copies the seat geometry, so grind the 20 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 32 mm housing.",
      "A single 71804 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71804 angular-contact bearing?",
        "a": "A 71804 single-row angular-contact ball bearing has a 20 mm bore, 32 mm outer diameter and 7 mm width (0.787 × 1.26 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 18 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71804 bore code work?",
        "a": "The last two digits of 71804 are bore code 04, giving 04 × 5 = 20 mm bore. The 32 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61804 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71804?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71804 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71804?",
        "a": "On a 20 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 7 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 6.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71804",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71805",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 37,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 21,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71805 carries bore code 05 = 25 mm. Outside diameter 37 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61805 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 25 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "At a 25 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 718xx thin section at 25 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7205.",
      "Draw-up on a thin-section 71805 is lighter than on a 72/73 bearing of the same bore: a 7 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 71805 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71805 angular-contact bearing?",
        "a": "A 71805 single-row angular-contact ball bearing has a 25 mm bore, 37 mm outer diameter and 7 mm width (0.984 × 1.457 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 21 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71805 bore code work?",
        "a": "The last two digits of 71805 are bore code 05, giving 05 × 5 = 25 mm bore. The 37 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61805 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71805?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71805 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71805 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 6.0 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 25 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71805",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71806",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 42,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 24,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71806 carries bore code 06 = 30 mm. Outside diameter 42 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61806 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 30 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "At a 30 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 718xx thin section at 30 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7206.",
      "The 42 mm outer ring of 71806 is only 6.0 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 7 mm-wide raceway long before the load rating is reached.",
      "Angular-contact 71806 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 71806 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71806 angular-contact bearing?",
        "a": "A 71806 single-row angular-contact ball bearing has a 30 mm bore, 42 mm outer diameter and 7 mm width (1.181 × 1.654 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 24 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71806 bore code work?",
        "a": "The last two digits of 71806 are bore code 06, giving 06 × 5 = 30 mm bore. The 42 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61806 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71806?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71806 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71806 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 30 mm bore the 71806 envelope is 30×42×7 mm with a 6.0 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71806",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71807",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 47,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 28,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71807 carries bore code 07 = 35 mm. Outside diameter 47 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61807 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 35 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At a 35 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 718xx thin section at 35 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7207.",
      "Pair thin-section 71807 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 6.0 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 35 mm spindle seat.",
      "Preload class matters: a 71807 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71807 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71807 angular-contact bearing?",
        "a": "A 71807 single-row angular-contact ball bearing has a 35 mm bore, 47 mm outer diameter and 7 mm width (1.378 × 1.85 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 28 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71807 bore code work?",
        "a": "The last two digits of 71807 are bore code 07, giving 07 × 5 = 35 mm bore. The 47 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61807 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71807?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71807 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71807?",
        "a": "On a 35 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 7 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 6.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71807",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71808",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 52,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 31,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71808 carries bore code 08 = 40 mm. Outside diameter 52 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61808 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 40 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "At a 40 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 718xx thin section at 40 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7208.",
      "With a 6.0 mm radial section on a 40 mm bore, the 71808 ring has little stiffness of its own: it copies the seat geometry, so grind the 40 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 52 mm housing.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71808 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 71808 where a deep-groove 61808 would do: same 40×52×7 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71808 angular-contact bearing?",
        "a": "A 71808 single-row angular-contact ball bearing has a 40 mm bore, 52 mm outer diameter and 7 mm width (1.575 × 2.047 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 31 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71808 bore code work?",
        "a": "The last two digits of 71808 are bore code 08, giving 08 × 5 = 40 mm bore. The 52 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61808 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71808?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71808 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71808 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 6.0 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 40 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71808",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71809",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 58,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 38,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71809 carries bore code 09 = 45 mm. Outside diameter 58 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61809 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 45 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "At a 45 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 718xx thin section at 45 mm bore has only a 6.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7209.",
      "Draw-up on a thin-section 71809 is lighter than on a 72/73 bearing of the same bore: a 7 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "Do not run a single 71809 where a deep-groove 61809 would do: same 45×58×7 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 7 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71809 angular-contact bearing?",
        "a": "A 71809 single-row angular-contact ball bearing has a 45 mm bore, 58 mm outer diameter and 7 mm width (1.772 × 2.283 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 38 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71809 bore code work?",
        "a": "The last two digits of 71809 are bore code 09, giving 09 × 5 = 45 mm bore. The 58 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61809 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71809?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71809 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71809 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 45 mm bore the 71809 envelope is 45×58×7 mm with a 6.5 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71809",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71810",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 65,
    "B_mm": 7,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 48,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71810 carries bore code 10 = 50 mm. Outside diameter 65 mm and width 7 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61810 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 50 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Thermal expansion on this 50 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 718xx thin section at 50 mm bore has only a 7.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7210.",
      "The 65 mm outer ring of 71810 is only 7.5 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 7 mm-wide raceway long before the load rating is reached.",
      "Shaft and housing fillets must clear the bearing chamfer so the 7 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71810 angular-contact bearing?",
        "a": "A 71810 single-row angular-contact ball bearing has a 50 mm bore, 65 mm outer diameter and 7 mm width (1.969 × 2.559 × 0.276 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 48 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71810 bore code work?",
        "a": "The last two digits of 71810 are bore code 10, giving 10 × 5 = 50 mm bore. The 65 mm outside diameter and 7 mm width follow the ISO 15 diameter series, shared with the 61810 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71810?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71810 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71810?",
        "a": "On a 50 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 7 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 7.5 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71810",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71811",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 72,
    "B_mm": 9,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 78,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71811 carries bore code 11 = 55 mm. Outside diameter 72 mm and width 9 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61811 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 55 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "Thermal expansion on this 55 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 718xx thin section at 55 mm bore has only a 8.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7211.",
      "Pair thin-section 71811 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 8.5 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 55 mm spindle seat.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 71811 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71811 angular-contact bearing?",
        "a": "A 71811 single-row angular-contact ball bearing has a 55 mm bore, 72 mm outer diameter and 9 mm width (2.165 × 2.835 × 0.354 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 78 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71811 bore code work?",
        "a": "The last two digits of 71811 are bore code 11, giving 11 × 5 = 55 mm bore. The 72 mm outside diameter and 9 mm width follow the ISO 15 diameter series, shared with the 61811 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71811?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71811 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71811 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 8.5 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 55 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71811",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71812",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 78,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 100,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71812 carries bore code 12 = 60 mm. Outside diameter 78 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61812 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 60 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "Thermal expansion on this 60 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 718xx thin section at 60 mm bore has only a 9.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7212.",
      "With a 9.0 mm radial section on a 60 mm bore, the 71812 ring has little stiffness of its own: it copies the seat geometry, so grind the 60 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 78 mm housing.",
      "A single 71812 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71812 angular-contact bearing?",
        "a": "A 71812 single-row angular-contact ball bearing has a 60 mm bore, 78 mm outer diameter and 10 mm width (2.362 × 3.071 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 100 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71812 bore code work?",
        "a": "The last two digits of 71812 are bore code 12, giving 12 × 5 = 60 mm bore. The 78 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61812 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71812?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71812 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71812 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 60 mm bore the 71812 envelope is 60×78×10 mm with a 9.0 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71812",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71813",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 85,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 120,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71813 carries bore code 13 = 65 mm. Outside diameter 85 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61813 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 65 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "Thermal expansion on this 65 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 718xx thin section at 65 mm bore has only a 10.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7213.",
      "Draw-up on a thin-section 71813 is lighter than on a 72/73 bearing of the same bore: a 10 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 71813 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71813 angular-contact bearing?",
        "a": "A 71813 single-row angular-contact ball bearing has a 65 mm bore, 85 mm outer diameter and 10 mm width (2.559 × 3.346 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 120 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71813 bore code work?",
        "a": "The last two digits of 71813 are bore code 13, giving 13 × 5 = 65 mm bore. The 85 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61813 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71813?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71813 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71813?",
        "a": "On a 65 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 10 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 10.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71813",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71814",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 90,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 128,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71814 carries bore code 14 = 70 mm. Outside diameter 90 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61814 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 70 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Thermal expansion on this 70 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 718xx thin section at 70 mm bore has only a 10.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7214.",
      "The 90 mm outer ring of 71814 is only 10.0 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 10 mm-wide raceway long before the load rating is reached.",
      "Angular-contact 71814 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 71814 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71814 angular-contact bearing?",
        "a": "A 71814 single-row angular-contact ball bearing has a 70 mm bore, 90 mm outer diameter and 10 mm width (2.756 × 3.543 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 128 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71814 bore code work?",
        "a": "The last two digits of 71814 are bore code 14, giving 14 × 5 = 70 mm bore. The 90 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61814 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71814?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71814 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71814 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 10.0 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 70 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71814",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71815",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 95,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 136,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71815 carries bore code 15 = 75 mm. Outside diameter 95 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61815 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 75 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Thermal expansion on this 75 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 718xx thin section at 75 mm bore has only a 10.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7215.",
      "Pair thin-section 71815 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 10.0 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 75 mm spindle seat.",
      "Preload class matters: a 71815 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71815 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71815 angular-contact bearing?",
        "a": "A 71815 single-row angular-contact ball bearing has a 75 mm bore, 95 mm outer diameter and 10 mm width (2.953 × 3.74 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 136 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71815 bore code work?",
        "a": "The last two digits of 71815 are bore code 15, giving 15 × 5 = 75 mm bore. The 95 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61815 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71815?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71815 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71815 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 75 mm bore the 71815 envelope is 75×95×10 mm with a 10.0 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71815",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71816",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 100,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 144,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71816 carries bore code 16 = 80 mm. Outside diameter 100 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61816 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 80 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "Mount this 80 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 718xx thin section at 80 mm bore has only a 10.0 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7216.",
      "With a 10.0 mm radial section on a 80 mm bore, the 71816 ring has little stiffness of its own: it copies the seat geometry, so grind the 80 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 100 mm housing.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71816 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 71816 where a deep-groove 61816 would do: same 80×100×10 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71816 angular-contact bearing?",
        "a": "A 71816 single-row angular-contact ball bearing has a 80 mm bore, 100 mm outer diameter and 10 mm width (3.15 × 3.937 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 144 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71816 bore code work?",
        "a": "The last two digits of 71816 are bore code 16, giving 16 × 5 = 80 mm bore. The 100 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61816 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71816?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71816 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71816?",
        "a": "On a 80 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 10 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 10.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71816",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71817",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 110,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 254,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71817 carries bore code 17 = 85 mm. Outside diameter 110 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61817 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 85 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "Mount this 85 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 718xx thin section at 85 mm bore has only a 12.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7217.",
      "Draw-up on a thin-section 71817 is lighter than on a 72/73 bearing of the same bore: a 13 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "Do not run a single 71817 where a deep-groove 61817 would do: same 85×110×13 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 13 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71817 angular-contact bearing?",
        "a": "A 71817 single-row angular-contact ball bearing has a 85 mm bore, 110 mm outer diameter and 13 mm width (3.346 × 4.331 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 254 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71817 bore code work?",
        "a": "The last two digits of 71817 are bore code 17, giving 17 × 5 = 85 mm bore. The 110 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61817 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71817?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71817 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71817 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 12.5 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 85 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71817",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71818",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 115,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 267,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71818 carries bore code 18 = 90 mm. Outside diameter 115 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61818 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 90 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Mount this 90 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 718xx thin section at 90 mm bore has only a 12.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7218.",
      "The 115 mm outer ring of 71818 is only 12.5 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 13 mm-wide raceway long before the load rating is reached.",
      "Shaft and housing fillets must clear the bearing chamfer so the 13 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71818 angular-contact bearing?",
        "a": "A 71818 single-row angular-contact ball bearing has a 90 mm bore, 115 mm outer diameter and 13 mm width (3.543 × 4.528 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 267 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71818 bore code work?",
        "a": "The last two digits of 71818 are bore code 18, giving 18 × 5 = 90 mm bore. The 115 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61818 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71818?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71818 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71818 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 90 mm bore the 71818 envelope is 90×115×13 mm with a 12.5 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71818",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71819",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 120,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 280,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71819 carries bore code 19 = 95 mm. Outside diameter 120 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61819 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 95 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "Mount this 95 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 718xx thin section at 95 mm bore has only a 12.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7219.",
      "Pair thin-section 71819 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 12.5 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 95 mm spindle seat.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 71819 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71819 angular-contact bearing?",
        "a": "A 71819 single-row angular-contact ball bearing has a 95 mm bore, 120 mm outer diameter and 13 mm width (3.74 × 4.724 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 280 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71819 bore code work?",
        "a": "The last two digits of 71819 are bore code 19, giving 19 × 5 = 95 mm bore. The 120 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61819 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71819?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71819 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71819?",
        "a": "On a 95 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 13 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 12.5 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71819",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71820",
    "brand": "GENERIC-ISO",
    "series": "71800-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 125,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 293,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71800-series (ISO 15 diameter series 8) the last two digits encode the bore: 71820 carries bore code 20 = 100 mm. Outside diameter 125 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61820 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 100 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "Mount this 100 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 718xx thin section at 100 mm bore has only a 12.5 mm radial section height: it saves space but is highly sensitive to misalignment and deflection — verify spindle stiffness before choosing it over a 7220.",
      "With a 12.5 mm radial section on a 100 mm bore, the 71820 ring has little stiffness of its own: it copies the seat geometry, so grind the 100 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 125 mm housing.",
      "A single 71820 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71820 angular-contact bearing?",
        "a": "A 71820 single-row angular-contact ball bearing has a 100 mm bore, 125 mm outer diameter and 13 mm width (3.937 × 4.921 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 293 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71820 bore code work?",
        "a": "The last two digits of 71820 are bore code 20, giving 20 × 5 = 100 mm bore. The 125 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61820 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71820?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71820 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71820 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 12.5 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 100 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71820",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71904",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 37,
    "B_mm": 9,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 35,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71904 carries bore code 04 = 20 mm. Outside diameter 37 mm and width 9 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61904 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 20 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At a 20 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 719xx thin section (8.5 mm section height at 20 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "With a 8.5 mm radial section on a 20 mm bore, the 71904 ring has little stiffness of its own: it copies the seat geometry, so grind the 20 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 37 mm housing.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 71904 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71904 angular-contact bearing?",
        "a": "A 71904 single-row angular-contact ball bearing has a 20 mm bore, 37 mm outer diameter and 9 mm width (0.787 × 1.457 × 0.354 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 35 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71904 bore code work?",
        "a": "The last two digits of 71904 are bore code 04, giving 04 × 5 = 20 mm bore. The 37 mm outside diameter and 9 mm width follow the ISO 15 diameter series, shared with the 61904 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71904?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71904 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71904?",
        "a": "On a 20 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 9 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 8.5 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71904",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71905",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 42,
    "B_mm": 9,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 41,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71905 carries bore code 05 = 25 mm. Outside diameter 42 mm and width 9 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61905 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 25 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "At a 25 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 719xx thin section (8.5 mm section height at 25 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Draw-up on a thin-section 71905 is lighter than on a 72/73 bearing of the same bore: a 9 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "Angular-contact 71905 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 71905 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71905 angular-contact bearing?",
        "a": "A 71905 single-row angular-contact ball bearing has a 25 mm bore, 42 mm outer diameter and 9 mm width (0.984 × 1.654 × 0.354 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 41 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71905 bore code work?",
        "a": "The last two digits of 71905 are bore code 05, giving 05 × 5 = 25 mm bore. The 42 mm outside diameter and 9 mm width follow the ISO 15 diameter series, shared with the 61905 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71905?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71905 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71905 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 8.5 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 25 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71905",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71906",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 47,
    "B_mm": 9,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 47,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71906 carries bore code 06 = 30 mm. Outside diameter 47 mm and width 9 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61906 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 30 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "At a 30 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 719xx thin section (8.5 mm section height at 30 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "The 47 mm outer ring of 71906 is only 8.5 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 9 mm-wide raceway long before the load rating is reached.",
      "Preload class matters: a 71906 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71906 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71906 angular-contact bearing?",
        "a": "A 71906 single-row angular-contact ball bearing has a 30 mm bore, 47 mm outer diameter and 9 mm width (1.181 × 1.85 × 0.354 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 47 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71906 bore code work?",
        "a": "The last two digits of 71906 are bore code 06, giving 06 × 5 = 30 mm bore. The 47 mm outside diameter and 9 mm width follow the ISO 15 diameter series, shared with the 61906 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71906?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71906 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71906 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 30 mm bore the 71906 envelope is 30×47×9 mm with a 8.5 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71906",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71907",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 55,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 72,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71907 carries bore code 07 = 35 mm. Outside diameter 55 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61907 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 35 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "At a 35 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 719xx thin section (10.0 mm section height at 35 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Pair thin-section 71907 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 10.0 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 35 mm spindle seat.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71907 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 71907 where a deep-groove 61907 would do: same 35×55×10 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71907 angular-contact bearing?",
        "a": "A 71907 single-row angular-contact ball bearing has a 35 mm bore, 55 mm outer diameter and 10 mm width (1.378 × 2.165 × 0.394 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 72 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71907 bore code work?",
        "a": "The last two digits of 71907 are bore code 07, giving 07 × 5 = 35 mm bore. The 55 mm outside diameter and 10 mm width follow the ISO 15 diameter series, shared with the 61907 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71907?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71907 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71907?",
        "a": "On a 35 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 10 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 10.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71907",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71908",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 62,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 108,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71908 carries bore code 08 = 40 mm. Outside diameter 62 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61908 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 40 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "At a 40 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 719xx thin section (11.0 mm section height at 40 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "With a 11.0 mm radial section on a 40 mm bore, the 71908 ring has little stiffness of its own: it copies the seat geometry, so grind the 40 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 62 mm housing.",
      "Do not run a single 71908 where a deep-groove 61908 would do: same 40×62×12 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 12 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71908 angular-contact bearing?",
        "a": "A 71908 single-row angular-contact ball bearing has a 40 mm bore, 62 mm outer diameter and 12 mm width (1.575 × 2.441 × 0.472 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 108 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71908 bore code work?",
        "a": "The last two digits of 71908 are bore code 08, giving 08 × 5 = 40 mm bore. The 62 mm outside diameter and 12 mm width follow the ISO 15 diameter series, shared with the 61908 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71908?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71908 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71908 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 11.0 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 40 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71908",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71909",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 68,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 125,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71909 carries bore code 09 = 45 mm. Outside diameter 68 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61909 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 45 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "At a 45 mm bore, shaft-seat finish and runout (target Ra ≤ 0.8 µm) govern angular-contact noise; a rough or out-of-round seat shows up as spindle runout before it shows as failure.",
      "The 719xx thin section (11.5 mm section height at 45 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Draw-up on a thin-section 71909 is lighter than on a 72/73 bearing of the same bore: a 12 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "Shaft and housing fillets must clear the bearing chamfer so the 12 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71909 angular-contact bearing?",
        "a": "A 71909 single-row angular-contact ball bearing has a 45 mm bore, 68 mm outer diameter and 12 mm width (1.772 × 2.677 × 0.472 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 125 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71909 bore code work?",
        "a": "The last two digits of 71909 are bore code 09, giving 09 × 5 = 45 mm bore. The 68 mm outside diameter and 12 mm width follow the ISO 15 diameter series, shared with the 61909 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71909?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71909 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71909 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 45 mm bore the 71909 envelope is 45×68×12 mm with a 11.5 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71909",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71910",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 72,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 129,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71910 carries bore code 10 = 50 mm. Outside diameter 72 mm and width 12 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61910 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 50 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "Thermal expansion on this 50 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 719xx thin section (11.0 mm section height at 50 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "The 72 mm outer ring of 71910 is only 11.0 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 12 mm-wide raceway long before the load rating is reached.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 71910 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71910 angular-contact bearing?",
        "a": "A 71910 single-row angular-contact ball bearing has a 50 mm bore, 72 mm outer diameter and 12 mm width (1.969 × 2.835 × 0.472 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 129 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71910 bore code work?",
        "a": "The last two digits of 71910 are bore code 10, giving 10 × 5 = 50 mm bore. The 72 mm outside diameter and 12 mm width follow the ISO 15 diameter series, shared with the 61910 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71910?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71910 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71910?",
        "a": "On a 50 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 12 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 11.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71910",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71911",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 80,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 176,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71911 carries bore code 11 = 55 mm. Outside diameter 80 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61911 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 55 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Thermal expansion on this 55 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 719xx thin section (12.5 mm section height at 55 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Pair thin-section 71911 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 12.5 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 55 mm spindle seat.",
      "A single 71911 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71911 angular-contact bearing?",
        "a": "A 71911 single-row angular-contact ball bearing has a 55 mm bore, 80 mm outer diameter and 13 mm width (2.165 × 3.15 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 176 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71911 bore code work?",
        "a": "The last two digits of 71911 are bore code 11, giving 11 × 5 = 55 mm bore. The 80 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61911 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71911?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71911 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71911 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 12.5 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 55 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71911",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71912",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 85,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 189,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71912 carries bore code 12 = 60 mm. Outside diameter 85 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61912 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 60 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Thermal expansion on this 60 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 719xx thin section (12.5 mm section height at 60 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "With a 12.5 mm radial section on a 60 mm bore, the 71912 ring has little stiffness of its own: it copies the seat geometry, so grind the 60 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 85 mm housing.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 71912 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71912 angular-contact bearing?",
        "a": "A 71912 single-row angular-contact ball bearing has a 60 mm bore, 85 mm outer diameter and 13 mm width (2.362 × 3.346 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 189 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71912 bore code work?",
        "a": "The last two digits of 71912 are bore code 12, giving 12 × 5 = 60 mm bore. The 85 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61912 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71912?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71912 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71912 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 60 mm bore the 71912 envelope is 60×85×13 mm with a 12.5 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71912",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71913",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 90,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 202,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71913 carries bore code 13 = 65 mm. Outside diameter 90 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61913 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 65 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles"
    ],
    "failure_modes": [
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection"
    ],
    "pitfalls": [
      "Thermal expansion on this 65 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 719xx thin section (12.5 mm section height at 65 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Draw-up on a thin-section 71913 is lighter than on a 72/73 bearing of the same bore: a 13 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "Angular-contact 71913 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian.",
      "Preload class matters: a 71913 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71913 angular-contact bearing?",
        "a": "A 71913 single-row angular-contact ball bearing has a 65 mm bore, 90 mm outer diameter and 13 mm width (2.559 × 3.543 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 202 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71913 bore code work?",
        "a": "The last two digits of 71913 are bore code 13, giving 13 × 5 = 65 mm bore. The 90 mm outside diameter and 13 mm width follow the ISO 15 diameter series, shared with the 61913 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71913?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71913 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71913?",
        "a": "On a 65 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 13 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 12.5 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71913",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71914",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 100,
    "B_mm": 16,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 327,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71914 carries bore code 14 = 70 mm. Outside diameter 100 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61914 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 70 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts"
    ],
    "failure_modes": [
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating"
    ],
    "pitfalls": [
      "Thermal expansion on this 70 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 719xx thin section (15.0 mm section height at 70 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "The 100 mm outer ring of 71914 is only 15.0 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 16 mm-wide raceway long before the load rating is reached.",
      "Preload class matters: a 71914 in a DB pair is supplied as preload class light (L) for speed or heavy (H) for rigidity; mixing unmarked bearings in a pair gives uneven preload and short life.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71914 backwards loads the low shoulder and displaces the balls out of the raceway."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71914 angular-contact bearing?",
        "a": "A 71914 single-row angular-contact ball bearing has a 70 mm bore, 100 mm outer diameter and 16 mm width (2.756 × 3.937 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 327 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71914 bore code work?",
        "a": "The last two digits of 71914 are bore code 14, giving 14 × 5 = 70 mm bore. The 100 mm outside diameter and 16 mm width follow the ISO 15 diameter series, shared with the 61914 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71914?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71914 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71914 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 15.0 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 70 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71914",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71915",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 105,
    "B_mm": 16,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 346,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71915 carries bore code 15 = 75 mm. Outside diameter 105 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61915 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 75 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes"
    ],
    "failure_modes": [
      "edge loading and early spalling from shaft deflection or housing misalignment",
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway"
    ],
    "pitfalls": [
      "Thermal expansion on this 75 mm bore consumes preload in a DB pair; size the preload class and clearance for the operating temperature, not the cold state.",
      "The 719xx thin section (15.0 mm section height at 75 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Pair thin-section 71915 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 15.0 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 75 mm spindle seat.",
      "Mounting direction is fixed by the asymmetric raceway — the marked side faces the axial load; installing 71915 backwards loads the low shoulder and displaces the balls out of the raceway.",
      "Do not run a single 71915 where a deep-groove 61915 would do: same 75×105×16 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71915 angular-contact bearing?",
        "a": "A 71915 single-row angular-contact ball bearing has a 75 mm bore, 105 mm outer diameter and 16 mm width (2.953 × 4.134 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 346 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71915 bore code work?",
        "a": "The last two digits of 71915 are bore code 15, giving 15 × 5 = 75 mm bore. The 105 mm outside diameter and 16 mm width follow the ISO 15 diameter series, shared with the 61915 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71915?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71915 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71915 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 75 mm bore the 71915 envelope is 75×105×16 mm with a 15.0 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71915",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71916",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 110,
    "B_mm": 16,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 365,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71916 carries bore code 16 = 80 mm. Outside diameter 110 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61916 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 80 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "medical and lab spindles",
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery"
    ],
    "failure_modes": [
      "electric pitting in VFD-driven spindles without shaft grounding protection",
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact"
    ],
    "pitfalls": [
      "Mount this 80 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 719xx thin section (15.0 mm section height at 80 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "With a 15.0 mm radial section on a 80 mm bore, the 71916 ring has little stiffness of its own: it copies the seat geometry, so grind the 80 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 110 mm housing.",
      "Do not run a single 71916 where a deep-groove 61916 would do: same 80×110×16 mm envelope, but the angular contact trades speed and noise for axial capacity and needs pairing.",
      "Shaft and housing fillets must clear the bearing chamfer so the 16 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71916 angular-contact bearing?",
        "a": "A 71916 single-row angular-contact ball bearing has a 80 mm bore, 110 mm outer diameter and 16 mm width (3.15 × 4.331 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 365 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71916 bore code work?",
        "a": "The last two digits of 71916 are bore code 16, giving 16 × 5 = 80 mm bore. The 110 mm outside diameter and 16 mm width follow the ISO 15 diameter series, shared with the 61916 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71916?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71916 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71916?",
        "a": "On a 80 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 16 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 15.0 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71916",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71917",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 120,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 518,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71917 carries bore code 17 = 85 mm. Outside diameter 120 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61917 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 85 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "clutch and idler shafts",
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms"
    ],
    "failure_modes": [
      "raceway spalling from axial overload exceeding the single-direction thrust rating",
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant"
    ],
    "pitfalls": [
      "Mount this 85 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 719xx thin section (17.5 mm section height at 85 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Draw-up on a thin-section 71917 is lighter than on a 72/73 bearing of the same bore: a 18 mm-wide ring clamps with a controlled light interference, and over-driving it bows the raceway — measure the mounted preload or runout rather than copying heavy-section fit tables.",
      "Shaft and housing fillets must clear the bearing chamfer so the 18 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71917 angular-contact bearing?",
        "a": "A 71917 single-row angular-contact ball bearing has a 85 mm bore, 120 mm outer diameter and 18 mm width (3.346 × 4.724 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 518 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71917 bore code work?",
        "a": "The last two digits of 71917 are bore code 17, giving 17 × 5 = 85 mm bore. The 120 mm outside diameter and 18 mm width follow the ISO 15 diameter series, shared with the 61917 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71917?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71917 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71917 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 17.5 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 85 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71917",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71918",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 125,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 543,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71918 carries bore code 18 = 90 mm. Outside diameter 125 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61918 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 90 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "semiconductor handling axes",
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables"
    ],
    "failure_modes": [
      "preload loss after a paired set runs loose, letting the balls skid and smear the raceway",
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep"
    ],
    "pitfalls": [
      "Mount this 90 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 719xx thin section (17.5 mm section height at 90 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "The 125 mm outer ring of 71918 is only 17.5 mm thick over the raceway: the housing bore must be round and rigid and the abutments square, because edge stress on a thin section spalls the 18 mm-wide raceway long before the load rating is reached.",
      "Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.",
      "A single 71918 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71918 angular-contact bearing?",
        "a": "A 71918 single-row angular-contact ball bearing has a 90 mm bore, 125 mm outer diameter and 18 mm width (3.543 × 4.921 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 543 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71918 bore code work?",
        "a": "The last two digits of 71918 are bore code 18, giving 18 × 5 = 90 mm bore. The 125 mm outside diameter and 18 mm width follow the ISO 15 diameter series, shared with the 61918 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71918?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71918 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "Why is the 71918 ring section so thin?",
        "a": "The 718/719 dimension series save radial space: at a 90 mm bore the 71918 envelope is 90×125×18 mm with a 17.5 mm radial section. That trades absolute load capacity for compactness and weight in robotics, medical and rotary-table axes — capacity per mm of section is high, but the ratings sit below a 72-series bearing of the same bore."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71918",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71919",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 130,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 568,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71919 carries bore code 19 = 95 mm. Outside diameter 130 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61919 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 95 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "packaging machinery",
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles"
    ],
    "failure_modes": [
      "raceway smearing under marginal lubrication at start-up before oil climb reaches the contact",
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary"
    ],
    "pitfalls": [
      "Mount this 95 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 719xx thin section (17.5 mm section height at 95 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "Pair thin-section 71919 units as a factory-matched set (universal SU/DU pairing): bench-pairing two singles with only 17.5 mm of section gives uncontrolled preload — order DB or DF pairs as one line item for the 95 mm spindle seat.",
      "A single 71919 angular-contact bearing takes axial load in ONE direction only — for bidirectional thrust, mount a matched pair (DB back-to-back or DF face-to-face), never rely on one row.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71919 angular-contact bearing?",
        "a": "A 71919 single-row angular-contact ball bearing has a 95 mm bore, 130 mm outer diameter and 18 mm width (3.74 × 5.118 × 0.709 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 568 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71919 bore code work?",
        "a": "The last two digits of 71919 are bore code 19, giving 19 × 5 = 95 mm bore. The 130 mm outside diameter and 18 mm width follow the ISO 15 diameter series, shared with the 61919 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71919?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71919 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "What fits suit a thin-section 71919?",
        "a": "On a 95 mm shaft use the catalogue thin-section fit bands (typically j5/k5 shaft seats with H6/H7 housings) and keep shoulders minimal; because the 18 mm-wide rings are flexible, seat roundness and square abutment faces matter more than heavy interference for keeping the 17.5 mm section stable under load."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71919",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "71920",
    "brand": "GENERIC-ISO",
    "series": "71900-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 140,
    "B_mm": 20,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "weight_g": 769,
    "weight_estimated": true,
    "standard": "ISO 15",
    "naming_rule_text": "In the 71900-series (ISO 15 diameter series 9) the last two digits encode the bore: 71920 carries bore code 20 = 100 mm. Outside diameter 140 mm and width 20 mm come from the ISO 15 boundary-dimensions general plan, shared with the 61920 deep-groove envelope. The '7' prefix marks a single-row angular-contact design with an asymmetric raceway and a nominal 40° contact angle (suffix C); a higher-angle variant carries more axial load, a 25° (E / A5) variant runs faster. For combined radial and axial load with a rotating inner ring on a 100 mm shaft, specify a k5 shaft seat with an H7 housing bore — verify against the load direction and magnitude, and pair two units (DB or DF) for bidirectional thrust.",
    "applications": [
      "robotics joint arms",
      "precision rotary tables",
      "medical and lab spindles",
      "clutch and idler shafts"
    ],
    "failure_modes": [
      "cage fracture from operation beyond the limiting speed with inadequate lubricant",
      "fretting corrosion on a loose shaft seat that lets the inner ring creep",
      "false brinelling from vibration while the shaft is stationary",
      "edge loading and early spalling from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount this 100 mm bore angular-contact pair by heating the inner rings (induction heater, max 120 °C) and clocking both faces; never drive a pair home through the outer rings.",
      "The 719xx thin section (20.0 mm section height at 100 mm bore) trades capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.",
      "With a 20.0 mm radial section on a 100 mm bore, the 71920 ring has little stiffness of its own: it copies the seat geometry, so grind the 100 mm shaft in one setup and check roundness — an out-of-round journal distorts the thin inner ring and reappears as vibration at the 140 mm housing.",
      "The 40° contact angle (suffix C) raises axial capacity but lowers speed versus a 25° (E / A5) variant; for high-speed spindles specify the 25° version, for heavy thrust specify 40°.",
      "Angular-contact 71920 tolerates only minutes of misalignment; a deflected shaft or a tilted housing face edge-loads the asymmetric raceway and spalls it early — align the seats to better than 0.001 radian."
    ],
    "faq": [
      {
        "q": "What are the dimensions of a 71920 angular-contact bearing?",
        "a": "A 71920 single-row angular-contact ball bearing has a 100 mm bore, 140 mm outer diameter and 20 mm width (3.937 × 5.512 × 0.787 in), per ISO 15 boundary dimensions. It is an open bearing with a nominal 40° contact angle. Geometry-based estimated mass is about 769 g for a brass-cage unit; catalogue masses vary with cage and ball complement."
      },
      {
        "q": "How does the 71920 bore code work?",
        "a": "The last two digits of 71920 are bore code 20, giving 20 × 5 = 100 mm bore. The 140 mm outside diameter and 20 mm width follow the ISO 15 diameter series, shared with the 61920 deep-groove envelope."
      },
      {
        "q": "What is the contact angle of 71920?",
        "a": "The nominal contact angle is 40° (suffix C): a higher angle carries more axial load but limits speed. A 25° (suffix E or A5) variant runs faster and is preferred for high-speed spindles; a 15° (suffix C7) version exists for very-high-speed duty. Confirm the angle and ball complement in the supplier catalogue."
      },
      {
        "q": "Can a single 71920 take axial load in both directions?",
        "a": "No. A single-row angular-contact bearing carries axial load in one direction only. For bidirectional thrust, mount a matched pair — DB (back-to-back) for a rigid, moment-resisting arrangement with preload class light (L) for speed or heavy (H) for stiffness, DF (face-to-face) for thermal expansion tolerance, or DT (tandem) to share one-direction load."
      },
      {
        "q": "How fast can a 71920 run?",
        "a": "Thin-section angular-contact bearings reach high speeds because the 20.0 mm section keeps the ball set light, but the practical limit is set by the lubricant and the precision of the 100 mm seat rather than the geometry alone; a 25° (E/A5) contact-angle variant and a light (L) preload class run faster than a 40° heavy-preloaded pair. Confirm the limiting speed in the supplier catalogue."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "71920",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.iso.org/obp/ui/en/#iso:std:iso:15:ed-4:v1:en",
    "catalog_ver": "iso15-ed4-geometry",
    "extracted_at": "2026-09-24",
    "last_verified": "2026-09-24",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [],
    "locale_variants": {},
    "temp_min_c": -40,
    "temp_max_c": 150,
    "clearance_options": [
      "CN",
      "C3"
    ]
  },
  {
    "sku": "7000-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7000",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 26,
    "B_mm": 8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 5.1,
    "static_load_kN": 2.07,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.16,
    "limiting_speed_rpm": 29000,
    "max_rpm": 29000,
    "speed_oil_rpm": 39000,
    "weight_g": 23,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7000 carries a 10 mm bore in a 26 mm outside diameter, 8 mm wide envelope. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 00 encodes the 10 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 2.07 kN versus C 5.1 kN, is what supports slow oscillating duty and shock without immediate brinelling. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Do not pair two random 7000 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "On a 10 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Do not pair two random 7000 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 5.1/2.07 kN ratings and 0.16 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7000; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7000?",
        "a": "7000 is a single-row angular contact ball bearing to ISO 15: 10 mm bore, 26 mm outside diameter, 8 mm width (0.394 x 1.024 x 0.315 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 5.1 kN, C0 2.07 kN and a 0.16 kN fatigue load limit Pu; the grease limiting speed is 29,000 r/min and the oil rating 39,000 r/min; mass about 23 g."
      },
      {
        "q": "How is the 7000 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 00 encodes the 10 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 26 mm OD and 8 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7000 support?",
        "a": "One 7000 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7000?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 29,000 r/min and the oil rating 39,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7000?",
        "a": "The 10/26/8 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 5.1 kN / C0 2.07 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7000",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7000",
      "7000-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5200S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5200S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.15,
    "static_load_kN": 3.9,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.23,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 50,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5200S measures 10 mm across the bore, 30 mm over the outer ring and 14.3 mm across the faces. NTN builds the number from 52 is the double-row dimension series (medium-duty 5200S double-row family), then 00 encodes the 10 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. With C 7.15 kN and C0 3.9 kN, each mm of bore carries about 0.72 kN of dynamic rating. Size selection is usually finished by checking that the C0 of 3.9 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The 17,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 5200S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "On a 10 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 7.15/3.9 kN ratings and 0.23 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5200S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5200S?",
        "a": "5200S is a double-row angular contact ball bearing to ISO 15: 10 mm bore, 30 mm outside diameter, 14.3 mm width (0.394 x 1.181 x 0.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.15 kN, C0 3.9 kN and a 0.23 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min; mass about 50 g."
      },
      {
        "q": "How is the 5200S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 00 encodes the 10 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 30 mm OD and 14.3 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5200S support?",
        "a": "5200S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5200S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5200S?",
        "a": "The 10/30/14.3 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.15 kN / C0 3.9 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5200S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5200s",
      "5200S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5200SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5200SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14.3,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.15,
    "static_load_kN": 3.9,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.23,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 50,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5200SCLLD carries a 10 mm bore in a 30 mm outside diameter, 14.3 mm wide envelope. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 00 encodes the 10 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The grease limiting speed is 15,000 r/min and no oil rating is printed for this execution. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 10 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Grease rated for deep-groove motor duty is not automatically right at 15,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 7.15/3.9 kN ratings and 0.23 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5200SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5200SCLLD?",
        "a": "5200SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 10 mm bore, 30 mm outside diameter, 14.3 mm width (0.394 x 1.181 x 0.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.15 kN, C0 3.9 kN and a 0.23 kN fatigue load limit Pu; the grease limiting speed is 15,000 r/min and no oil rating is printed for this execution; mass about 50 g."
      },
      {
        "q": "How is the 5200SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 00 encodes the 10 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 30 mm OD and 14.3 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5200SCLLD support?",
        "a": "5200SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5200SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 15,000 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5200SCLLD?",
        "a": "The 10/30/14.3 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.15 kN / C0 3.9 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5200SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5200sclld",
      "5200SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5200SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5200SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14.3,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.15,
    "static_load_kN": 3.9,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.23,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 50,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5200SCLLM is the 10 mm bore member of NTN's medium-duty 5200S double-row family, with a 30 mm outside diameter and 14.3 mm section width. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 00 encodes the 10 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. With C 7.15 kN and C0 3.9 kN, each mm of bore carries about 0.72 kN of dynamic rating. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 17,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5200SCLLM without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "On a 10 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 7.15/3.9 kN ratings and 0.23 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5200SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5200SCLLM?",
        "a": "5200SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 10 mm bore, 30 mm outside diameter, 14.3 mm width (0.394 x 1.181 x 0.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.15 kN, C0 3.9 kN and a 0.23 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min; mass about 50 g."
      },
      {
        "q": "How is the 5200SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 00 encodes the 10 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 30 mm OD and 14.3 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5200SCLLM support?",
        "a": "5200SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5200SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5200SCLLM?",
        "a": "The 10/30/14.3 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.15 kN / C0 3.9 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5200SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5200scllm",
      "5200SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5200SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5200SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14.3,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.15,
    "static_load_kN": 3.9,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.23,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 50,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5200SCZZ measures 10 mm across the bore, 30 mm over the outer ring and 14.3 mm across the faces. NTN builds the number from 52 is the double-row dimension series (medium-duty 5200S double-row family), then 00 encodes the 10 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. Catalogue dynamic rating C is 7.15 kN against C0 3.9 kN — a C0/C ratio of 0.55 that is typical of an angular-contact contact ellipse. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5200SCZZ without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 7.15/3.9 kN ratings and 0.23 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5200SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5200SCZZ?",
        "a": "5200SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 10 mm bore, 30 mm outside diameter, 14.3 mm width (0.394 x 1.181 x 0.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.15 kN, C0 3.9 kN and a 0.23 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min; mass about 50 g."
      },
      {
        "q": "How is the 5200SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 00 encodes the 10 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 30 mm OD and 14.3 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5200SCZZ support?",
        "a": "5200SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5200SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5200SCZZ?",
        "a": "The 10/30/14.3 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.15 kN / C0 3.9 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5200SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5200sczz",
      "5200SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7200-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7200",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 6,
    "static_load_kN": 2.74,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.21,
    "limiting_speed_rpm": 28000,
    "max_rpm": 28000,
    "speed_oil_rpm": 37000,
    "weight_g": 29,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7200 is the 10 mm bore member of NTN's medium-duty 7200 single-row family, with a 30 mm outside diameter and 9 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 00 encodes the 10 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 10.0 mm, and the catalogue couples that with C 6 kN / C0 2.74 kN. For a 10 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7200 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7200 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 6/2.74 kN ratings and 0.21 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7200; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7200?",
        "a": "7200 is a single-row angular contact ball bearing to ISO 15: 10 mm bore, 30 mm outside diameter, 9 mm width (0.394 x 1.181 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 6 kN, C0 2.74 kN and a 0.21 kN fatigue load limit Pu; the grease limiting speed is 28,000 r/min and the oil rating 37,000 r/min; mass about 29 g."
      },
      {
        "q": "How is the 7200 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 00 encodes the 10 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 mm OD and 9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7200 support?",
        "a": "One 7200 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7200?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 28,000 r/min and the oil rating 37,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7200?",
        "a": "The 10/30/9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 6 kN / C0 2.74 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7200",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 10×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7200-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 10×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7200-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 10×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7200",
      "7200-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7200B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7200B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 5.5,
    "static_load_kN": 2.52,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.2,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "speed_oil_rpm": 32000,
    "weight_g": 29,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7200B carries a 10 mm bore in a 30 mm outside diameter, 9 mm wide envelope. Decoding 7200B: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 00 encodes the 10 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The radial section height here is 10.0 mm, and the catalogue couples that with C 5.5 kN / C0 2.52 kN. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 10 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Do not pair two random 7200B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 5.5/2.52 kN ratings and 0.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7200B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7200B?",
        "a": "7200B is a single-row angular contact ball bearing to ISO 15: 10 mm bore, 30 mm outside diameter, 9 mm width (0.394 x 1.181 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 5.5 kN, C0 2.52 kN and a 0.2 kN fatigue load limit Pu; the grease limiting speed is 24,000 r/min and the oil rating 32,000 r/min; mass about 29 g."
      },
      {
        "q": "How is the 7200B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 00 encodes the 10 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 30 mm OD and 9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7200B support?",
        "a": "One 7200B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7200B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 24,000 r/min and the oil rating 32,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7200B?",
        "a": "The 10/30/9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 5.5 kN / C0 2.52 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7200B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7200b",
      "7200B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7300-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7300",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 11.2,
    "static_load_kN": 4.95,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.39,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "speed_oil_rpm": 34000,
    "weight_g": 40,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 10 x 35 x 11 mm, NTN 7300 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Decoding 7300: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 00 encodes the 10 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 40 g, which at this 12.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 10 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 26,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 26,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 11.2/4.95 kN ratings and 0.39 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7300; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7300?",
        "a": "7300 is a single-row angular contact ball bearing to ISO 15: 10 mm bore, 35 mm outside diameter, 11 mm width (0.394 x 1.378 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 11.2 kN, C0 4.95 kN and a 0.39 kN fatigue load limit Pu; the grease limiting speed is 26,000 r/min and the oil rating 34,000 r/min; mass about 40 g."
      },
      {
        "q": "How is the 7300 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 00 encodes the 10 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 35 mm OD and 11 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7300 support?",
        "a": "One 7300 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7300?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 26,000 r/min and the oil rating 34,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7300?",
        "a": "The 10/35/11 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 11.2 kN / C0 4.95 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7300",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7300",
      "7300-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7300B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7300B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10.5,
    "static_load_kN": 4.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.36,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "speed_oil_rpm": 29000,
    "weight_g": 41,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7300B appears as a heavy-duty 7300 single-row family bearing of 10 mm bore, 35 mm outside diameter and 11 mm width. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 00 encodes the 10 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 10 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 10 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7300B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The C0 of 4.6 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 22,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 10.5/4.6 kN ratings and 0.36 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7300B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7300B?",
        "a": "7300B is a single-row angular contact ball bearing to ISO 15: 10 mm bore, 35 mm outside diameter, 11 mm width (0.394 x 1.378 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 10.5 kN, C0 4.6 kN and a 0.36 kN fatigue load limit Pu; the grease limiting speed is 22,000 r/min and the oil rating 29,000 r/min; mass about 41 g."
      },
      {
        "q": "How is the 7300B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 00 encodes the 10 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 35 mm OD and 11 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7300B support?",
        "a": "One 7300B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7300B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 22,000 r/min and the oil rating 29,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7300B?",
        "a": "The 10/35/11 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 10.5 kN / C0 4.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7300B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7300b",
      "7300B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7001-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7001",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 28,
    "B_mm": 8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 5.6,
    "static_load_kN": 2.46,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.19,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "speed_oil_rpm": 35000,
    "weight_g": 25,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 12 x 28 x 8 mm, NTN 7001 sits in the standard-section 7000 single-row family of the angular-contact programme. Decoding 7001: 70 is the single-row dimension series (standard-section 7000 single-row family), with 01 encodes the 12 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 35,000 r/min sits 9,000 r/min above the 26,000 r/min grease figure — a 1.35x step that says how much headroom oil cooling buys. Size selection is usually finished by checking that the C0 of 2.46 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "A 7001 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 26,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 5.6/2.46 kN ratings and 0.19 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7001; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7001?",
        "a": "7001 is a single-row angular contact ball bearing to ISO 15: 12 mm bore, 28 mm outside diameter, 8 mm width (0.472 x 1.102 x 0.315 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 5.6 kN, C0 2.46 kN and a 0.19 kN fatigue load limit Pu; the grease limiting speed is 26,000 r/min and the oil rating 35,000 r/min; mass about 25 g."
      },
      {
        "q": "How is the 7001 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 01 encodes the 12 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 28 mm OD and 8 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7001 support?",
        "a": "One 7001 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7001?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 26,000 r/min and the oil rating 35,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7001?",
        "a": "The 12/28/8 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 5.6 kN / C0 2.46 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7001",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7001",
      "7001-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5201S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5201S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10.5,
    "static_load_kN": 5.8,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.35,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "speed_oil_rpm": 20000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5201S belongs to the medium-duty 5200S double-row family: the catalogue boundary dimensions read 12 / 32 / 15.9 mm (bore / OD / width). Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 01 encodes the 12 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The oil rating of 20,000 r/min sits 5,000 r/min above the 15,000 r/min grease figure — a 1.33x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 12 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Do not pair two random 5201S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Grease rated for deep-groove motor duty is not automatically right at 15,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 10.5/5.8 kN ratings and 0.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5201S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5201S?",
        "a": "5201S is a double-row angular contact ball bearing to ISO 15: 12 mm bore, 32 mm outside diameter, 15.9 mm width (0.472 x 1.26 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 10.5 kN, C0 5.8 kN and a 0.35 kN fatigue load limit Pu; the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min; mass about 60 g."
      },
      {
        "q": "How is the 5201S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 01 encodes the 12 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 32 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5201S support?",
        "a": "5201S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5201S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5201S?",
        "a": "The 12/32/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 10.5 kN / C0 5.8 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5201S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5201s",
      "5201S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5201SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5201SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.5,
    "static_load_kN": 5.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5201SCLLD carries a 12 mm bore in a 32 mm outside diameter, 15.9 mm wide envelope. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 01 encodes the 12 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The radial section height here is 10.0 mm, and the catalogue couples that with C 8.5 kN / C0 5.3 kN. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 12,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 8.5/5.3 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5201SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5201SCLLD?",
        "a": "5201SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 12 mm bore, 32 mm outside diameter, 15.9 mm width (0.472 x 1.26 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.5 kN, C0 5.3 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 12,000 r/min and no oil rating is printed for this execution; mass about 60 g."
      },
      {
        "q": "How is the 5201SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 01 encodes the 12 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 32 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5201SCLLD support?",
        "a": "5201SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5201SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 12,000 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5201SCLLD?",
        "a": "The 12/32/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.5 kN / C0 5.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5201SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5201sclld",
      "5201SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5201SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5201SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.5,
    "static_load_kN": 5.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "speed_oil_rpm": 20000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5201SCLLM is the 12 mm bore member of NTN's medium-duty 5200S double-row family, with a 32 mm outside diameter and 15.9 mm section width. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 01 encodes the 12 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. A 12 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A 5201SCLLM mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 5.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 15,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 8.5/5.3 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5201SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5201SCLLM?",
        "a": "5201SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 12 mm bore, 32 mm outside diameter, 15.9 mm width (0.472 x 1.26 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.5 kN, C0 5.3 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min; mass about 60 g."
      },
      {
        "q": "How is the 5201SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 01 encodes the 12 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 32 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5201SCLLM support?",
        "a": "5201SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5201SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5201SCLLM?",
        "a": "The 12/32/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.5 kN / C0 5.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5201SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5201scllm",
      "5201SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5201SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5201SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.5,
    "static_load_kN": 5.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "speed_oil_rpm": 20000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5201SCZZ is an NTN sealed double-row angular contact ball bearing: medium-duty 5200S double-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 12 x 32 x 15.9 mm. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 01 encodes the 12 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. At roughly 10.0 mm of radial section, the catalogue still quotes 8.5 kN dynamic capacity for the 12 mm bore. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "On a 12 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 8.5/5.3 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5201SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5201SCZZ?",
        "a": "5201SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 12 mm bore, 32 mm outside diameter, 15.9 mm width (0.472 x 1.26 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.5 kN, C0 5.3 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min; mass about 60 g."
      },
      {
        "q": "How is the 5201SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 01 encodes the 12 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 32 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5201SCZZ support?",
        "a": "5201SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5201SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5201SCZZ?",
        "a": "The 12/32/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.5 kN / C0 5.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5201SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5201sczz",
      "5201SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7201-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7201",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.4,
    "static_load_kN": 3.95,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 25000,
    "max_rpm": 25000,
    "speed_oil_rpm": 33000,
    "weight_g": 35,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 12 x 32 x 10 mm, NTN 7201 sits in the medium-duty 7200 single-row family of the angular-contact programme. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 01 encodes the 12 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 25,000 r/min and the oil rating 33,000 r/min. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Heat-mounting to 80-90 deg C is the clean route onto a 12 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7201 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The C0 of 3.95 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 8.4/3.95 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7201; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7201?",
        "a": "7201 is a single-row angular contact ball bearing to ISO 15: 12 mm bore, 32 mm outside diameter, 10 mm width (0.472 x 1.26 x 0.394 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.4 kN, C0 3.95 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 25,000 r/min and the oil rating 33,000 r/min; mass about 35 g."
      },
      {
        "q": "How is the 7201 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 01 encodes the 12 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 32 mm OD and 10 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7201 support?",
        "a": "One 7201 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7201?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 25,000 r/min and the oil rating 33,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7201?",
        "a": "The 12/32/10 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.4 kN / C0 3.95 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7201",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7201-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7201-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×32×10 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7201",
      "7201-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7201B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7201B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.75,
    "static_load_kN": 3.65,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.29,
    "limiting_speed_rpm": 21000,
    "max_rpm": 21000,
    "speed_oil_rpm": 28000,
    "weight_g": 36,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7201B measures 12 mm across the bore, 32 mm over the outer ring and 10 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 01 encodes the 12 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). On speed, the grease limiting speed is 21,000 r/min and the oil rating 28,000 r/min. The 12/32/10 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 12 mm bore give the working limits. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The 21,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The C0 of 3.65 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 7.75/3.65 kN ratings and 0.29 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7201B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7201B?",
        "a": "7201B is a single-row angular contact ball bearing to ISO 15: 12 mm bore, 32 mm outside diameter, 10 mm width (0.472 x 1.26 x 0.394 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.75 kN, C0 3.65 kN and a 0.29 kN fatigue load limit Pu; the grease limiting speed is 21,000 r/min and the oil rating 28,000 r/min; mass about 36 g."
      },
      {
        "q": "How is the 7201B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 01 encodes the 12 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 32 mm OD and 10 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7201B support?",
        "a": "One 7201B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7201B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 21,000 r/min and the oil rating 28,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7201B?",
        "a": "The 12/32/10 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.75 kN / C0 3.65 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7201B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7201b",
      "7201B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7301-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7301",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 12.4,
    "static_load_kN": 5.25,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.41,
    "limiting_speed_rpm": 23000,
    "max_rpm": 23000,
    "speed_oil_rpm": 30000,
    "weight_g": 44,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7301 is the 12 mm bore member of NTN's heavy-duty 7300 single-row family, with a 37 mm outside diameter and 12 mm section width. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 01 encodes the 12 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 12.5 mm, and the catalogue couples that with C 12.4 kN / C0 5.25 kN. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Heat-mounting to 80-90 deg C is the clean route onto a 12 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7301 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "On a 12 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 12.4/5.25 kN ratings and 0.41 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7301; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7301?",
        "a": "7301 is a single-row angular contact ball bearing to ISO 15: 12 mm bore, 37 mm outside diameter, 12 mm width (0.472 x 1.457 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 12.4 kN, C0 5.25 kN and a 0.41 kN fatigue load limit Pu; the grease limiting speed is 23,000 r/min and the oil rating 30,000 r/min; mass about 44 g."
      },
      {
        "q": "How is the 7301 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 01 encodes the 12 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 37 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7301 support?",
        "a": "One 7301 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7301?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 23,000 r/min and the oil rating 30,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7301?",
        "a": "The 12/37/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 12.4 kN / C0 5.25 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7301",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×37×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7301-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×37×12 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7301-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 12×37×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7301",
      "7301-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7301B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7301B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 11.7,
    "static_load_kN": 4.95,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.39,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "speed_oil_rpm": 26000,
    "weight_g": 45,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 12 x 37 x 12 mm, NTN 7301B sits in the heavy-duty 7300 single-row family of the angular-contact programme. Decoding 7301B: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 01 encodes the 12 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The radial section height here is 12.5 mm, and the catalogue couples that with C 11.7 kN / C0 4.95 kN. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 12 mm bore give the working limits. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 12 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Grease rated for deep-groove motor duty is not automatically right at 19,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 11.7/4.95 kN ratings and 0.39 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7301B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7301B?",
        "a": "7301B is a single-row angular contact ball bearing to ISO 15: 12 mm bore, 37 mm outside diameter, 12 mm width (0.472 x 1.457 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 11.7 kN, C0 4.95 kN and a 0.39 kN fatigue load limit Pu; the grease limiting speed is 19,000 r/min and the oil rating 26,000 r/min; mass about 45 g."
      },
      {
        "q": "How is the 7301B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 01 encodes the 12 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 37 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7301B support?",
        "a": "One 7301B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7301B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 19,000 r/min and the oil rating 26,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7301B?",
        "a": "The 12/37/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 11.7 kN / C0 4.95 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7301B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7301b",
      "7301B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7002-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7002",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 32,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 6.4,
    "static_load_kN": 3.15,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.25,
    "limiting_speed_rpm": 23000,
    "max_rpm": 23000,
    "speed_oil_rpm": 31000,
    "weight_g": 35,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7002 is the 15 mm bore member of NTN's standard-section 7000 single-row family, with a 32 mm outside diameter and 9 mm section width. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 02 encodes the 15 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 6.4 kN against C0 3.15 kN — a C0/C ratio of 0.49 that is typical of an angular-contact contact ellipse. The 15/32/9 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 6.4/3.15 kN ratings and 0.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7002; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7002?",
        "a": "7002 is a single-row angular contact ball bearing to ISO 15: 15 mm bore, 32 mm outside diameter, 9 mm width (0.591 x 1.26 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 6.4 kN, C0 3.15 kN and a 0.25 kN fatigue load limit Pu; the grease limiting speed is 23,000 r/min and the oil rating 31,000 r/min; mass about 35 g."
      },
      {
        "q": "How is the 7002 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 02 encodes the 15 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 32 mm OD and 9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7002 support?",
        "a": "One 7002 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7002?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 23,000 r/min and the oil rating 31,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7002?",
        "a": "The 15/32/9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 6.4 kN / C0 3.15 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7002",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7002",
      "7002-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5202S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5202S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 11.7,
    "static_load_kN": 7.05,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.42,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 17000,
    "weight_g": 70,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5202S is the 15 mm bore member of NTN's medium-duty 5200S double-row family, with a 35 mm outside diameter and 15.9 mm section width. Decoding 5202S: 52 is the double-row dimension series (medium-duty 5200S double-row family), with 02 encodes the 15 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. At roughly 10.0 mm of radial section, the catalogue still quotes 11.7 kN dynamic capacity for the 15 mm bore. Choose the medium-duty 5200S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 15 mm bore give the working limits. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 13,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 11.7/7.05 kN ratings and 0.42 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5202S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5202S?",
        "a": "5202S is a double-row angular contact ball bearing to ISO 15: 15 mm bore, 35 mm outside diameter, 15.9 mm width (0.591 x 1.378 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 11.7 kN, C0 7.05 kN and a 0.42 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min; mass about 70 g."
      },
      {
        "q": "How is the 5202S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 02 encodes the 15 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 35 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5202S support?",
        "a": "5202S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5202S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5202S?",
        "a": "The 15/35/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 11.7 kN / C0 7.05 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5202S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5202s",
      "5202S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5202SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5202SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.5,
    "static_load_kN": 5.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 70,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5202SCLLD appears as a medium-duty 5200S double-row family bearing of 15 mm bore, 35 mm outside diameter and 15.9 mm width. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 02 encodes the 15 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. With C 8.5 kN and C0 5.3 kN, each mm of bore carries about 0.57 kN of dynamic rating. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 12,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5202SCLLD without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "On a 15 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 8.5/5.3 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5202SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5202SCLLD?",
        "a": "5202SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 15 mm bore, 35 mm outside diameter, 15.9 mm width (0.591 x 1.378 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.5 kN, C0 5.3 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 12,000 r/min and no oil rating is printed for this execution; mass about 70 g."
      },
      {
        "q": "How is the 5202SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 02 encodes the 15 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 35 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5202SCLLD support?",
        "a": "5202SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5202SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 12,000 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5202SCLLD?",
        "a": "The 15/35/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.5 kN / C0 5.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5202SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5202sclld",
      "5202SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5202SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5202SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.5,
    "static_load_kN": 5.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 17000,
    "weight_g": 70,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5202SCLLM carries a 15 mm bore in a 35 mm outside diameter, 15.9 mm wide envelope. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 02 encodes the 15 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The built-in back-to-back contact lines give the double-row bearing its two-direction thrust and moment capacity from one ring set. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. A 15 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The 13,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 5202SCLLM mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A 5202SCLLM mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 8.5/5.3 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5202SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5202SCLLM?",
        "a": "5202SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 15 mm bore, 35 mm outside diameter, 15.9 mm width (0.591 x 1.378 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.5 kN, C0 5.3 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min; mass about 70 g."
      },
      {
        "q": "How is the 5202SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 02 encodes the 15 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 35 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5202SCLLM support?",
        "a": "5202SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5202SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5202SCLLM?",
        "a": "The 15/35/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.5 kN / C0 5.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5202SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5202scllm",
      "5202SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5202SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5202SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.5,
    "static_load_kN": 5.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.31,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 17000,
    "weight_g": 70,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5202SCZZ appears as a medium-duty 5200S double-row family bearing of 15 mm bore, 35 mm outside diameter and 15.9 mm width. Decoding 5202SCZZ: 52 is the double-row dimension series (medium-duty 5200S double-row family), with 02 encodes the 15 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. NTN prints 8.5 kN dynamic and 5.3 kN static for this size and a 0.31 kN fatigue load limit Pu. For a 15 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Do not pair two random 5202SCZZ bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5202SCZZ without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 8.5/5.3 kN ratings and 0.31 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5202SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5202SCZZ?",
        "a": "5202SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 15 mm bore, 35 mm outside diameter, 15.9 mm width (0.591 x 1.378 x 0.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.5 kN, C0 5.3 kN and a 0.31 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min; mass about 70 g."
      },
      {
        "q": "How is the 5202SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 02 encodes the 15 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 35 mm OD and 15.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5202SCZZ support?",
        "a": "5202SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5202SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5202SCZZ?",
        "a": "The 15/35/15.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.5 kN / C0 5.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5202SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5202sczz",
      "5202SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7202",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10,
    "static_load_kN": 4.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.37,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "speed_oil_rpm": 29000,
    "weight_g": 46,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7202 is the 15 mm bore member of NTN's medium-duty 7200 single-row family, with a 35 mm outside diameter and 11 mm section width. Decoding 7202: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 02 encodes the 15 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 10 kN and C0 4.7 kN, each mm of bore carries about 0.67 kN of dynamic rating. Against a deep-groove bearing of the same 15 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Heat-mounting to 80-90 deg C is the clean route onto a 15 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Do not pair two random 7202 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Do not pair two random 7202 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "On a 15 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 10/4.7 kN ratings and 0.37 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7202; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7202?",
        "a": "7202 is a single-row angular contact ball bearing to ISO 15: 15 mm bore, 35 mm outside diameter, 11 mm width (0.591 x 1.378 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 10 kN, C0 4.7 kN and a 0.37 kN fatigue load limit Pu; the grease limiting speed is 22,000 r/min and the oil rating 29,000 r/min; mass about 46 g."
      },
      {
        "q": "How is the 7202 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 02 encodes the 15 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 35 mm OD and 11 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7202 support?",
        "a": "One 7202 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7202?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 22,000 r/min and the oil rating 29,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7202?",
        "a": "The 15/35/11 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 10 kN / C0 4.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7202-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7202-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7202-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7202-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202",
      "7202-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7202B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 9.25,
    "static_load_kN": 4.35,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.34,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "speed_oil_rpm": 25000,
    "weight_g": 46,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7202B belongs to the medium-duty 7200 single-row family: the catalogue boundary dimensions read 15 / 35 / 11 mm (bore / OD / width). Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 02 encodes the 15 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The static margin, C0 4.35 kN versus C 9.25 kN, is what supports slow oscillating duty and shock without immediate brinelling. Size selection is usually finished by checking that the C0 of 4.35 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Do not pair two random 7202B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 9.25/4.35 kN ratings and 0.34 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7202B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7202B?",
        "a": "7202B is a single-row angular contact ball bearing to ISO 15: 15 mm bore, 35 mm outside diameter, 11 mm width (0.591 x 1.378 x 0.433 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 9.25 kN, C0 4.35 kN and a 0.34 kN fatigue load limit Pu; the grease limiting speed is 18,000 r/min and the oil rating 25,000 r/min; mass about 46 g."
      },
      {
        "q": "How is the 7202B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 02 encodes the 15 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 35 mm OD and 11 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7202B support?",
        "a": "One 7202B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7202B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 18,000 r/min and the oil rating 25,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7202B?",
        "a": "The 15/35/11 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 9.25 kN / C0 4.35 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202b",
      "7202B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5302S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5302S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 17.6,
    "static_load_kN": 10.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.62,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 5300S double-row family entry 5302S carries a 15 mm bore in a 42 mm outside diameter, 19 mm wide envelope. Reading the code: 53 is the double-row dimension series (heavy-duty 5300S double-row family), 02 encodes the 15 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The oil rating of 15,000 r/min sits 4,000 r/min above the 11,000 r/min grease figure — a 1.36x step that says how much headroom oil cooling buys. For a 15 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 15 mm bore give the working limits. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The C0 of 10.2 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Grease rated for deep-groove motor duty is not automatically right at 11,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 11,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 17.6/10.2 kN ratings and 0.62 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5302S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5302S?",
        "a": "5302S is a double-row angular contact ball bearing to ISO 15: 15 mm bore, 42 mm outside diameter, 19 mm width (0.591 x 1.654 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 17.6 kN, C0 10.2 kN and a 0.62 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 130 g."
      },
      {
        "q": "How is the 5302S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 02 encodes the 15 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 42 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5302S support?",
        "a": "5302S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5302S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5302S?",
        "a": "The 15/42/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 17.6 kN / C0 10.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5302S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5302s",
      "5302S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7302-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7302",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 14.9,
    "static_load_kN": 7.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.56,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "speed_oil_rpm": 26000,
    "weight_g": 55,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7302 measures 15 mm across the bore, 42 mm over the outer ring and 13 mm across the faces. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 02 encodes the 15 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 26,000 r/min sits 7,000 r/min above the 19,000 r/min grease figure — a 1.37x step that says how much headroom oil cooling buys. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 15 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7302 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 19,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Grease rated for deep-groove motor duty is not automatically right at 19,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 14.9/7.2 kN ratings and 0.56 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7302; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7302?",
        "a": "7302 is a single-row angular contact ball bearing to ISO 15: 15 mm bore, 42 mm outside diameter, 13 mm width (0.591 x 1.654 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 14.9 kN, C0 7.2 kN and a 0.56 kN fatigue load limit Pu; the grease limiting speed is 19,000 r/min and the oil rating 26,000 r/min; mass about 55 g."
      },
      {
        "q": "How is the 7302 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 02 encodes the 15 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 42 mm OD and 13 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7302 support?",
        "a": "One 7302 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7302?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 19,000 r/min and the oil rating 26,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7302?",
        "a": "The 15/42/13 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 14.9 kN / C0 7.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7302",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7302-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7302-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7302-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7302",
      "7302-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7302B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7302B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 13.8,
    "static_load_kN": 6.65,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.52,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 57,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7302B is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 15 x 42 x 13 mm. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 02 encodes the 15 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). On speed, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. Against a deep-groove bearing of the same 15 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 15 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Do not pair two random 7302B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7302B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The C0 of 6.65 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 13.8/6.65 kN ratings and 0.52 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7302B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7302B?",
        "a": "7302B is a single-row angular contact ball bearing to ISO 15: 15 mm bore, 42 mm outside diameter, 13 mm width (0.591 x 1.654 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 13.8 kN, C0 6.65 kN and a 0.52 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min; mass about 57 g."
      },
      {
        "q": "How is the 7302B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 02 encodes the 15 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 42 mm OD and 13 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7302B support?",
        "a": "One 7302B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7302B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7302B?",
        "a": "The 15/42/13 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 13.8 kN / C0 6.65 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7302B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7302b",
      "7302B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7003-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7003",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 35,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.95,
    "static_load_kN": 3.85,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.3,
    "limiting_speed_rpm": 21000,
    "max_rpm": 21000,
    "speed_oil_rpm": 28000,
    "weight_g": 46,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 17 x 35 x 10 mm, NTN 7003 sits in the standard-section 7000 single-row family of the angular-contact programme. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 03 encodes the 17 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 7.95 kN dynamic and 3.85 kN static for this size and a 0.3 kN fatigue load limit Pu. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 17 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 17 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7003 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7003 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 7.95/3.85 kN ratings and 0.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7003; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7003?",
        "a": "7003 is a single-row angular contact ball bearing to ISO 15: 17 mm bore, 35 mm outside diameter, 10 mm width (0.669 x 1.378 x 0.394 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.95 kN, C0 3.85 kN and a 0.3 kN fatigue load limit Pu; the grease limiting speed is 21,000 r/min and the oil rating 28,000 r/min; mass about 46 g."
      },
      {
        "q": "How is the 7003 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 03 encodes the 17 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 35 mm OD and 10 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7003 support?",
        "a": "One 7003 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7003?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 21,000 r/min and the oil rating 28,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7003?",
        "a": "The 17/35/10 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.95 kN / C0 3.85 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7003",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7003",
      "7003-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5203S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5203S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 14.6,
    "static_load_kN": 9.05,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.54,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5203S appears as a medium-duty 5200S double-row family bearing of 17 mm bore, 40 mm outside diameter and 17.5 mm width. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 03 encodes the 17 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Against a deep-groove bearing of the same 17 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "On a 17 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 11,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 14.6/9.05 kN ratings and 0.54 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5203S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5203S?",
        "a": "5203S is a double-row angular contact ball bearing to ISO 15: 17 mm bore, 40 mm outside diameter, 17.5 mm width (0.669 x 1.575 x 0.689 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 14.6 kN, C0 9.05 kN and a 0.54 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 100 g."
      },
      {
        "q": "How is the 5203S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 03 encodes the 17 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 40 mm OD and 17.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5203S support?",
        "a": "5203S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5203S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5203S?",
        "a": "The 17/40/17.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 14.6 kN / C0 9.05 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5203S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5203s",
      "5203S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5203SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5203SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 8.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.49,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5203SCLLD appears as a medium-duty 5200S double-row family bearing of 17 mm bore, 40 mm outside diameter and 17.5 mm width. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 03 encodes the 17 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. A 17 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A 5203SCLLD mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 8.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 10,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 12.7/8.3 kN ratings and 0.49 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5203SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5203SCLLD?",
        "a": "5203SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 17 mm bore, 40 mm outside diameter, 17.5 mm width (0.669 x 1.575 x 0.689 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 12.7 kN, C0 8.3 kN and a 0.49 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and no oil rating is printed for this execution; mass about 100 g."
      },
      {
        "q": "How is the 5203SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 40 mm OD and 17.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5203SCLLD support?",
        "a": "5203SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5203SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5203SCLLD?",
        "a": "The 17/40/17.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 12.7 kN / C0 8.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5203SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5203sclld",
      "5203SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5203SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5203SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 8.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.49,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5203SCLLM carries a 17 mm bore in a 40 mm outside diameter, 17.5 mm wide envelope. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 03 encodes the 17 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. At roughly 11.5 mm of radial section, the catalogue still quotes 12.7 kN dynamic capacity for the 17 mm bore. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 17 mm bore give the working limits. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The C0 of 8.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5203SCLLM without re-checking axial float, heat and housing width — the kinematics differ.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 12.7/8.3 kN ratings and 0.49 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5203SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5203SCLLM?",
        "a": "5203SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 17 mm bore, 40 mm outside diameter, 17.5 mm width (0.669 x 1.575 x 0.689 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 12.7 kN, C0 8.3 kN and a 0.49 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 100 g."
      },
      {
        "q": "How is the 5203SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 40 mm OD and 17.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5203SCLLM support?",
        "a": "5203SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5203SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5203SCLLM?",
        "a": "The 17/40/17.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 12.7 kN / C0 8.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5203SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5203scllm",
      "5203SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5203SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5203SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 8.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.49,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5203SCZZ is an NTN sealed double-row angular contact ball bearing: medium-duty 5200S double-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 17 x 40 x 17.5 mm. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. Catalogue mass is about 100 g, which at this 11.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The C0 of 8.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 12.7/8.3 kN ratings and 0.49 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5203SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5203SCZZ?",
        "a": "5203SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 17 mm bore, 40 mm outside diameter, 17.5 mm width (0.669 x 1.575 x 0.689 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 12.7 kN, C0 8.3 kN and a 0.49 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 100 g."
      },
      {
        "q": "How is the 5203SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 40 mm OD and 17.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5203SCZZ support?",
        "a": "5203SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5203SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5203SCZZ?",
        "a": "The 17/40/17.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 12.7 kN / C0 8.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5203SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5203sczz",
      "5203SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7203",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 13.2,
    "static_load_kN": 6.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.52,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "speed_oil_rpm": 26000,
    "weight_g": 64,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7203 measures 17 mm across the bore, 40 mm over the outer ring and 12 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 03 encodes the 17 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 6.6 kN versus C 13.2 kN, is what supports slow oscillating duty and shock without immediate brinelling. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Heat-mounting to 80-90 deg C is the clean route onto a 17 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The C0 of 6.6 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Do not pair two random 7203 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 13.2/6.6 kN ratings and 0.52 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7203; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7203?",
        "a": "7203 is a single-row angular contact ball bearing to ISO 15: 17 mm bore, 40 mm outside diameter, 12 mm width (0.669 x 1.575 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 13.2 kN, C0 6.6 kN and a 0.52 kN fatigue load limit Pu; the grease limiting speed is 19,000 r/min and the oil rating 26,000 r/min; mass about 64 g."
      },
      {
        "q": "How is the 7203 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 03 encodes the 17 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 40 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7203 support?",
        "a": "One 7203 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7203?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 19,000 r/min and the oil rating 26,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7203?",
        "a": "The 17/40/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 13.2 kN / C0 6.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203",
      "7203-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7203B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 12.2,
    "static_load_kN": 6.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.48,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 66,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203B is the 17 mm bore member of NTN's medium-duty 7200 single-row family, with a 40 mm outside diameter and 12 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 03 encodes the 17 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue dynamic rating C is 12.2 kN against C0 6.1 kN — a C0/C ratio of 0.50 that is typical of an angular-contact contact ellipse. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. A 17 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 17,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The C0 of 6.1 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 12.2/6.1 kN ratings and 0.48 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7203B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7203B?",
        "a": "7203B is a single-row angular contact ball bearing to ISO 15: 17 mm bore, 40 mm outside diameter, 12 mm width (0.669 x 1.575 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 12.2 kN, C0 6.1 kN and a 0.48 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min; mass about 66 g."
      },
      {
        "q": "How is the 7203B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 03 encodes the 17 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7203B support?",
        "a": "One 7203B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7203B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7203B?",
        "a": "The 17/40/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 12.2 kN / C0 6.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203b",
      "7203B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5303S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5303S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 21,
    "static_load_kN": 12.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.77,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 5300S double-row family, 5303S measures 17 mm across the bore, 47 mm over the outer ring and 22.2 mm across the faces. Decoding 5303S: 53 is the double-row dimension series (heavy-duty 5300S double-row family), with 03 encodes the 17 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. At roughly 15.0 mm of radial section, the catalogue still quotes 21 kN dynamic capacity for the 17 mm bore. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5303S without re-checking axial float, heat and housing width — the kinematics differ.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 21/12.6 kN ratings and 0.77 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5303S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5303S?",
        "a": "5303S is a double-row angular contact ball bearing to ISO 15: 17 mm bore, 47 mm outside diameter, 22.2 mm width (0.669 x 1.85 x 0.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 21 kN, C0 12.6 kN and a 0.77 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 5303S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 03 encodes the 17 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 47 mm OD and 22.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5303S support?",
        "a": "5303S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5303S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5303S?",
        "a": "The 17/47/22.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 21 kN / C0 12.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5303S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5303s",
      "5303S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5303SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5303SCLLD",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.6,
    "static_load_kN": 12.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.75,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 5300S double-row family entry 5303SCLLD carries a 17 mm bore in a 47 mm outside diameter, 22.2 mm wide envelope. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 03 encodes the 17 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. Catalogue mass is about 180 g, which at this 15.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Against a deep-groove bearing of the same 17 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 9,500 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The 9,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The C0 of 12.4 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 19.6/12.4 kN ratings and 0.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5303SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5303SCLLD?",
        "a": "5303SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 17 mm bore, 47 mm outside diameter, 22.2 mm width (0.669 x 1.85 x 0.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.6 kN, C0 12.4 kN and a 0.75 kN fatigue load limit Pu; the grease limiting speed is 9,500 r/min and no oil rating is printed for this execution; mass about 180 g."
      },
      {
        "q": "How is the 5303SCLLD designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 47 mm OD and 22.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5303SCLLD support?",
        "a": "5303SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5303SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,500 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5303SCLLD?",
        "a": "The 17/47/22.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.6 kN / C0 12.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5303SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5303sclld",
      "5303SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5303SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5303SCLLM",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.6,
    "static_load_kN": 12.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.75,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5303SCLLM is the 17 mm bore member of NTN's heavy-duty 5300S double-row family, with a 47 mm outside diameter and 22.2 mm section width. Decoding 5303SCLLM: 53 is the double-row dimension series (heavy-duty 5300S double-row family), with 03 encodes the 17 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. NTN prints 19.6 kN dynamic and 12.4 kN static for this size and a 0.75 kN fatigue load limit Pu. Against a deep-groove bearing of the same 17 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 17 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5303SCLLM without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5303SCLLM without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 19.6/12.4 kN ratings and 0.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5303SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5303SCLLM?",
        "a": "5303SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 17 mm bore, 47 mm outside diameter, 22.2 mm width (0.669 x 1.85 x 0.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.6 kN, C0 12.4 kN and a 0.75 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 5303SCLLM designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 47 mm OD and 22.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5303SCLLM support?",
        "a": "5303SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5303SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5303SCLLM?",
        "a": "The 17/47/22.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.6 kN / C0 12.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5303SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5303scllm",
      "5303SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5303SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5303SCZZ",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.6,
    "static_load_kN": 12.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.75,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5303SCZZ appears as a heavy-duty 5300S double-row family bearing of 17 mm bore, 47 mm outside diameter and 22.2 mm width. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 03 encodes the 17 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. NTN prints 19.6 kN dynamic and 12.4 kN static for this size and a 0.75 kN fatigue load limit Pu. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5303SCZZ without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 19.6/12.4 kN ratings and 0.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5303SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5303SCZZ?",
        "a": "5303SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 17 mm bore, 47 mm outside diameter, 22.2 mm width (0.669 x 1.85 x 0.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.6 kN, C0 12.4 kN and a 0.75 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 5303SCZZ designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 03 encodes the 17 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 47 mm OD and 22.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5303SCZZ support?",
        "a": "5303SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5303SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5303SCZZ?",
        "a": "The 17/47/22.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.6 kN / C0 12.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5303SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5303sczz",
      "5303SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7303-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7303",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 17.7,
    "static_load_kN": 8.65,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.68,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "speed_oil_rpm": 24000,
    "weight_g": 107,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7303 is the 17 mm bore member of NTN's heavy-duty 7300 single-row family, with a 47 mm outside diameter and 14 mm section width. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 03 encodes the 17 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 15.0 mm of radial section, the catalogue still quotes 17.7 kN dynamic capacity for the 17 mm bore. For a 17 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 17 mm bore give the working limits. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 17.7/8.65 kN ratings and 0.68 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7303; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7303?",
        "a": "7303 is a single-row angular contact ball bearing to ISO 15: 17 mm bore, 47 mm outside diameter, 14 mm width (0.669 x 1.85 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 17.7 kN, C0 8.65 kN and a 0.68 kN fatigue load limit Pu; the grease limiting speed is 18,000 r/min and the oil rating 24,000 r/min; mass about 107 g."
      },
      {
        "q": "How is the 7303 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 03 encodes the 17 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 47 mm OD and 14 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7303 support?",
        "a": "One 7303 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7303?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 18,000 r/min and the oil rating 24,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7303?",
        "a": "The 17/47/14 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 17.7 kN / C0 8.65 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7303-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7303-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7303-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7303",
      "7303-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7303B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7303B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.4,
    "static_load_kN": 8.05,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.63,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "speed_oil_rpm": 20000,
    "weight_g": 109,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7303B carries a 17 mm bore in a 47 mm outside diameter, 14 mm wide envelope. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 03 encodes the 17 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The static margin, C0 8.05 kN versus C 16.4 kN, is what supports slow oscillating duty and shock without immediate brinelling. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 17 mm shaft typically takes a j5/k5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 17 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 8.05 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Do not pair two random 7303B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 16.4/8.05 kN ratings and 0.63 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7303B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7303B?",
        "a": "7303B is a single-row angular contact ball bearing to ISO 15: 17 mm bore, 47 mm outside diameter, 14 mm width (0.669 x 1.85 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.4 kN, C0 8.05 kN and a 0.63 kN fatigue load limit Pu; the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min; mass about 109 g."
      },
      {
        "q": "How is the 7303B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 03 encodes the 17 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 47 mm OD and 14 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7303B support?",
        "a": "One 7303B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7303B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7303B?",
        "a": "The 17/47/14 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.4 kN / C0 8.05 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7303b",
      "7303B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7004-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7004",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 42,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 10.7,
    "static_load_kN": 5.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.44,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "speed_oil_rpm": 25000,
    "weight_g": 80,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7004 is the 20 mm bore member of NTN's standard-section 7000 single-row family, with a 42 mm outside diameter and 12 mm section width. NTN builds the number from 70 is the single-row dimension series (standard-section 7000 single-row family), then 04 encodes the 20 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Heat-mounting to 80-90 deg C is the clean route onto a 20 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 19,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 10.7/5.6 kN ratings and 0.44 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7004; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7004?",
        "a": "7004 is a single-row angular contact ball bearing to ISO 15: 20 mm bore, 42 mm outside diameter, 12 mm width (0.787 x 1.654 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 10.7 kN, C0 5.6 kN and a 0.44 kN fatigue load limit Pu; the grease limiting speed is 19,000 r/min and the oil rating 25,000 r/min; mass about 80 g."
      },
      {
        "q": "How is the 7004 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 04 encodes the 20 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 42 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7004 support?",
        "a": "One 7004 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7004?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 19,000 r/min and the oil rating 25,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7004?",
        "a": "The 20/42/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 10.7 kN / C0 5.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7004",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7004",
      "7004-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5204S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5204S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.6,
    "static_load_kN": 12.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.75,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 20 x 47 x 20.6 mm, NTN 5204S sits in the medium-duty 5200S double-row family of the angular-contact programme. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 04 encodes the 20 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The radial section height here is 13.5 mm, and the catalogue couples that with C 19.6 kN / C0 12.4 kN. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 20 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "A 5204S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 12.4 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 19.6/12.4 kN ratings and 0.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5204S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5204S?",
        "a": "5204S is a double-row angular contact ball bearing to ISO 15: 20 mm bore, 47 mm outside diameter, 20.6 mm width (0.787 x 1.85 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.6 kN, C0 12.4 kN and a 0.75 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min; mass about 160 g."
      },
      {
        "q": "How is the 5204S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 04 encodes the 20 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 47 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5204S support?",
        "a": "5204S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5204S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5204S?",
        "a": "The 20/47/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.6 kN / C0 12.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5204S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5204s",
      "5204S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5204SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5204SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 10.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.64,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5204SCLLD appears as a medium-duty 5200S double-row family bearing of 20 mm bore, 47 mm outside diameter and 20.6 mm width. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 04 encodes the 20 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The static margin, C0 10.7 kN versus C 15.9 kN, is what supports slow oscillating duty and shock without immediate brinelling. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 20 mm bore give the working limits. ",
    "applications": [
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The 9,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 9,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 5204SCLLD bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 15.9/10.7 kN ratings and 0.64 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5204SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5204SCLLD?",
        "a": "5204SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 20 mm bore, 47 mm outside diameter, 20.6 mm width (0.787 x 1.85 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 15.9 kN, C0 10.7 kN and a 0.64 kN fatigue load limit Pu; the grease limiting speed is 9,000 r/min and no oil rating is printed for this execution; mass about 160 g."
      },
      {
        "q": "How is the 5204SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 04 encodes the 20 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 47 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5204SCLLD support?",
        "a": "5204SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5204SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,000 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5204SCLLD?",
        "a": "The 20/47/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 15.9 kN / C0 10.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5204SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5204sclld",
      "5204SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5204SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5204SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 10.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.64,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5204SCLLM carries a 20 mm bore in a 47 mm outside diameter, 20.6 mm wide envelope. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 04 encodes the 20 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. On speed, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Do not pair two random 5204SCLLM bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The C0 of 10.7 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 15.9/10.7 kN ratings and 0.64 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5204SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5204SCLLM?",
        "a": "5204SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 20 mm bore, 47 mm outside diameter, 20.6 mm width (0.787 x 1.85 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 15.9 kN, C0 10.7 kN and a 0.64 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min; mass about 160 g."
      },
      {
        "q": "How is the 5204SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 04 encodes the 20 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 47 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5204SCLLM support?",
        "a": "5204SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5204SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5204SCLLM?",
        "a": "The 20/47/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 15.9 kN / C0 10.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5204SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5204scllm",
      "5204SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5204SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5204SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 10.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.64,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 13000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5204SCZZ appears as a medium-duty 5200S double-row family bearing of 20 mm bore, 47 mm outside diameter and 20.6 mm width. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 04 encodes the 20 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The radial section height here is 13.5 mm, and the catalogue couples that with C 15.9 kN / C0 10.7 kN. Against a deep-groove bearing of the same 20 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The C0 of 10.7 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 15.9/10.7 kN ratings and 0.64 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5204SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5204SCZZ?",
        "a": "5204SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 20 mm bore, 47 mm outside diameter, 20.6 mm width (0.787 x 1.85 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 15.9 kN, C0 10.7 kN and a 0.64 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min; mass about 160 g."
      },
      {
        "q": "How is the 5204SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 04 encodes the 20 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 47 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5204SCZZ support?",
        "a": "5204SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5204SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5204SCZZ?",
        "a": "The 20/47/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 15.9 kN / C0 10.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5204SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5204sczz",
      "5204SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7204",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.1,
    "static_load_kN": 8.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.66,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 23000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 is the 20 mm bore member of NTN's medium-duty 7200 single-row family, with a 47 mm outside diameter and 14 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 04 encodes the 20 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 16.1 kN against C0 8.4 kN — a C0/C ratio of 0.52 that is typical of an angular-contact contact ellipse. Against a deep-groove bearing of the same 20 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 17,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 20 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 16.1/8.4 kN ratings and 0.66 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7204; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7204?",
        "a": "7204 is a single-row angular contact ball bearing to ISO 15: 20 mm bore, 47 mm outside diameter, 14 mm width (0.787 x 1.85 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.1 kN, C0 8.4 kN and a 0.66 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 23,000 r/min; mass about 100 g."
      },
      {
        "q": "How is the 7204 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 04 encodes the 20 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 47 mm OD and 14 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7204 support?",
        "a": "One 7204 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7204?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 23,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7204?",
        "a": "The 20/47/14 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.1 kN / C0 8.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204",
      "7204-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7204B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 14.7,
    "static_load_kN": 7.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.6,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "speed_oil_rpm": 20000,
    "weight_g": 102,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7204B appears as a medium-duty 7200 single-row family bearing of 20 mm bore, 47 mm outside diameter and 14 mm width. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 04 encodes the 20 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). NTN prints 14.7 kN dynamic and 7.7 kN static for this size and a 0.6 kN fatigue load limit Pu. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "On a 20 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Grease rated for deep-groove motor duty is not automatically right at 15,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7204B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 14.7/7.7 kN ratings and 0.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7204B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7204B?",
        "a": "7204B is a single-row angular contact ball bearing to ISO 15: 20 mm bore, 47 mm outside diameter, 14 mm width (0.787 x 1.85 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 14.7 kN, C0 7.7 kN and a 0.6 kN fatigue load limit Pu; the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min; mass about 102 g."
      },
      {
        "q": "How is the 7204B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 04 encodes the 20 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 47 mm OD and 14 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7204B support?",
        "a": "One 7204B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7204B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 15,000 r/min and the oil rating 20,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7204B?",
        "a": "The 20/47/14 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 14.7 kN / C0 7.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204b",
      "7204B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5304S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5304S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 24.6,
    "static_load_kN": 15,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.93,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "speed_oil_rpm": 12000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5304S belongs to the heavy-duty 5300S double-row family: the catalogue boundary dimensions read 20 / 52 / 22.2 mm (bore / OD / width). The designation breaks down as 53 is the double-row dimension series (heavy-duty 5300S double-row family); 04 encodes the 20 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. A 20 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The 9,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 9,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 24.6/15 kN ratings and 0.93 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5304S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5304S?",
        "a": "5304S is a double-row angular contact ball bearing to ISO 15: 20 mm bore, 52 mm outside diameter, 22.2 mm width (0.787 x 2.047 x 0.874 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 24.6 kN, C0 15 kN and a 0.93 kN fatigue load limit Pu; the grease limiting speed is 9,000 r/min and the oil rating 12,000 r/min; mass about 220 g."
      },
      {
        "q": "How is the 5304S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 04 encodes the 20 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 52 mm OD and 22.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5304S support?",
        "a": "5304S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5304S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,000 r/min and the oil rating 12,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5304S?",
        "a": "The 20/52/22.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 24.6 kN / C0 15 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5304S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5304s",
      "5304S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7304",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 20.7,
    "static_load_kN": 10.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.81,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "speed_oil_rpm": 21000,
    "weight_g": 138,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7304 measures 20 mm across the bore, 52 mm over the outer ring and 15 mm across the faces. Decoding 7304: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 04 encodes the 20 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 20.7 kN dynamic and 10.4 kN static for this size and a 0.81 kN fatigue load limit Pu. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 20 mm bore give the working limits. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 16,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7304 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 20.7/10.4 kN ratings and 0.81 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7304; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7304?",
        "a": "7304 is a single-row angular contact ball bearing to ISO 15: 20 mm bore, 52 mm outside diameter, 15 mm width (0.787 x 2.047 x 0.591 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 20.7 kN, C0 10.4 kN and a 0.81 kN fatigue load limit Pu; the grease limiting speed is 16,000 r/min and the oil rating 21,000 r/min; mass about 138 g."
      },
      {
        "q": "How is the 7304 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 04 encodes the 20 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 52 mm OD and 15 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7304 support?",
        "a": "One 7304 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7304?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 16,000 r/min and the oil rating 21,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7304?",
        "a": "The 20/52/15 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 20.7 kN / C0 10.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304",
      "7304-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7304B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.2,
    "static_load_kN": 9.65,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.76,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 18000,
    "weight_g": 141,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7304B measures 20 mm across the bore, 52 mm over the outer ring and 15 mm across the faces. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 04 encodes the 20 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue dynamic rating C is 19.2 kN against C0 9.65 kN — a C0/C ratio of 0.50 that is typical of an angular-contact contact ellipse. For a 20 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 20 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 20 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 19.2/9.65 kN ratings and 0.76 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7304B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7304B?",
        "a": "7304B is a single-row angular contact ball bearing to ISO 15: 20 mm bore, 52 mm outside diameter, 15 mm width (0.787 x 2.047 x 0.591 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.2 kN, C0 9.65 kN and a 0.76 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 18,000 r/min; mass about 141 g."
      },
      {
        "q": "How is the 7304B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 04 encodes the 20 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 52 mm OD and 15 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7304B support?",
        "a": "One 7304B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7304B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 18,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7304B?",
        "a": "The 20/52/15 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.2 kN / C0 9.65 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304b",
      "7304B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7905",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7905",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 42,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 7.9,
    "static_load_kN": 4.95,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 0.36,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "speed_oil_rpm": 22000,
    "weight_g": 50,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 25 x 42 x 9 mm, NTN 7905 sits in the extra-light, high-speed 7900 single-row family of the angular-contact programme. Reading the code: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 4.95 kN static rating into useful one-direction thrust capacity. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 17,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 4.95 kN really covers the worst static case before substituting it for a 7000.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A 7905 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 7.9/4.95 kN ratings and 0.36 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7905; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7905?",
        "a": "7905 is a single-row angular contact ball bearing to ISO 15: 25 mm bore, 42 mm outside diameter, 9 mm width (0.984 x 1.654 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 7.9 kN, C0 4.95 kN and a 0.36 kN fatigue load limit Pu; the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min; mass about 50 g."
      },
      {
        "q": "How is the 7905 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 42 mm OD and 9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7905 support?",
        "a": "One 7905 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7905?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 17,000 r/min and the oil rating 22,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7905?",
        "a": "The 25/42/9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 7.9 kN / C0 4.95 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7905",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7905"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7005-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7005",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 47,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 11.9,
    "static_load_kN": 6.85,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.54,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "speed_oil_rpm": 21000,
    "weight_g": 93,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 25 x 47 x 12 mm, NTN 7005 sits in the standard-section 7000 single-row family of the angular-contact programme. Decoding 7005: 70 is the single-row dimension series (standard-section 7000 single-row family), with 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 11.0 mm, and the catalogue couples that with C 11.9 kN / C0 6.85 kN. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 16,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 6.85 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Do not pair two random 7005 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 11.9/6.85 kN ratings and 0.54 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7005; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7005?",
        "a": "7005 is a single-row angular contact ball bearing to ISO 15: 25 mm bore, 47 mm outside diameter, 12 mm width (0.984 x 1.85 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 11.9 kN, C0 6.85 kN and a 0.54 kN fatigue load limit Pu; the grease limiting speed is 16,000 r/min and the oil rating 21,000 r/min; mass about 93 g."
      },
      {
        "q": "How is the 7005 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 47 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7005 support?",
        "a": "One 7005 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7005?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 16,000 r/min and the oil rating 21,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7005?",
        "a": "The 25/47/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 11.9 kN / C0 6.85 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7005",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7005",
      "7005-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5205S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5205S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 21.3,
    "static_load_kN": 14.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.88,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "speed_oil_rpm": 11000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5205S is an NTN double-row angular contact ball bearing: medium-duty 5200S double-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 25 x 52 x 20.6 mm. NTN builds the number from 52 is the double-row dimension series (medium-duty 5200S double-row family), then 05 encodes the 25 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. On speed, the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min. For a 25 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Grease rated for deep-groove motor duty is not automatically right at 8,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The C0 of 14.7 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 21.3/14.7 kN ratings and 0.88 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5205S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5205S?",
        "a": "5205S is a double-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 20.6 mm width (0.984 x 2.047 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 21.3 kN, C0 14.7 kN and a 0.88 kN fatigue load limit Pu; the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 5205S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 05 encodes the 25 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 52 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5205S support?",
        "a": "5205S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5205S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5205S?",
        "a": "The 25/52/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 21.3 kN / C0 14.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5205S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5205s",
      "5205S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5205SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5205SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.9,
    "static_load_kN": 12.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.74,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5205SCLLD measures 25 mm across the bore, 52 mm over the outer ring and 20.6 mm across the faces. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 05 encodes the 25 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. At roughly 13.5 mm of radial section, the catalogue still quotes 16.9 kN dynamic capacity for the 25 mm bore. For a 25 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 25 mm bore give the working limits. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The C0 of 12.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5205SCLLD without re-checking axial float, heat and housing width — the kinematics differ.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 16.9/12.3 kN ratings and 0.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5205SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5205SCLLD?",
        "a": "5205SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 20.6 mm width (0.984 x 2.047 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.9 kN, C0 12.3 kN and a 0.74 kN fatigue load limit Pu; the grease limiting speed is 7,500 r/min and no oil rating is printed for this execution; mass about 180 g."
      },
      {
        "q": "How is the 5205SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 52 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5205SCLLD support?",
        "a": "5205SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5205SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,500 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5205SCLLD?",
        "a": "The 25/52/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.9 kN / C0 12.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5205SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5205sclld",
      "5205SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5205SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5205SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.9,
    "static_load_kN": 12.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.74,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "speed_oil_rpm": 11000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5205SCLLM appears as a medium-duty 5200S double-row family bearing of 25 mm bore, 52 mm outside diameter and 20.6 mm width. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 05 encodes the 25 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The oil rating of 11,000 r/min sits 2,500 r/min above the 8,500 r/min grease figure — a 1.29x step that says how much headroom oil cooling buys. For a 25 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Grease rated for deep-groove motor duty is not automatically right at 8,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 16.9/12.3 kN ratings and 0.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5205SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5205SCLLM?",
        "a": "5205SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 20.6 mm width (0.984 x 2.047 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.9 kN, C0 12.3 kN and a 0.74 kN fatigue load limit Pu; the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 5205SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 52 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5205SCLLM support?",
        "a": "5205SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5205SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5205SCLLM?",
        "a": "The 25/52/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.9 kN / C0 12.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5205SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5205scllm",
      "5205SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5205SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5205SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.9,
    "static_load_kN": 12.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.74,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "speed_oil_rpm": 11000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5205SCZZ is an NTN sealed double-row angular contact ball bearing: medium-duty 5200S double-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 25 x 52 x 20.6 mm. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 05 encodes the 25 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. On speed, the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Grease rated for deep-groove motor duty is not automatically right at 8,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 8,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The C0 of 12.3 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 16.9/12.3 kN ratings and 0.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5205SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5205SCZZ?",
        "a": "5205SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 20.6 mm width (0.984 x 2.047 x 0.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.9 kN, C0 12.3 kN and a 0.74 kN fatigue load limit Pu; the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 5205SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 52 mm OD and 20.6 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5205SCZZ support?",
        "a": "5205SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5205SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,500 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5205SCZZ?",
        "a": "The 25/52/20.6 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.9 kN / C0 12.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5205SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5205sczz",
      "5205SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7205",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 18,
    "static_load_kN": 10.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.81,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "speed_oil_rpm": 19000,
    "weight_g": 125,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7205 measures 25 mm across the bore, 52 mm over the outer ring and 15 mm across the faces. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 13.5 mm of radial section, the catalogue still quotes 18 kN dynamic capacity for the 25 mm bore. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Grease quantity matters as much as grade at 14,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 14,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 18/10.3 kN ratings and 0.81 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7205; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7205?",
        "a": "7205 is a single-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 15 mm width (0.984 x 2.047 x 0.591 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 18 kN, C0 10.3 kN and a 0.81 kN fatigue load limit Pu; the grease limiting speed is 14,000 r/min and the oil rating 19,000 r/min; mass about 125 g."
      },
      {
        "q": "How is the 7205 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 52 mm OD and 15 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7205 support?",
        "a": "One 7205 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7205?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 14,000 r/min and the oil rating 19,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7205?",
        "a": "The 25/52/15 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 18 kN / C0 10.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205",
      "7205-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7205B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 16.4,
    "static_load_kN": 9.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.74,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "speed_oil_rpm": 16000,
    "weight_g": 129,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 25 x 52 x 15 mm, NTN 7205B sits in the medium-duty 7200 single-row family of the angular-contact programme. Decoding 7205B: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 05 encodes the 25 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 129 g, which at this 13.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Against a deep-groove bearing of the same 25 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 12,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A 7205B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7205B without re-checking axial float, heat and housing width — the kinematics differ.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 16.4/9.4 kN ratings and 0.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7205B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7205B?",
        "a": "7205B is a single-row angular contact ball bearing to ISO 15: 25 mm bore, 52 mm outside diameter, 15 mm width (0.984 x 2.047 x 0.591 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 16.4 kN, C0 9.4 kN and a 0.74 kN fatigue load limit Pu; the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min; mass about 129 g."
      },
      {
        "q": "How is the 7205B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 05 encodes the 25 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 52 mm OD and 15 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7205B support?",
        "a": "One 7205B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7205B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7205B?",
        "a": "The 25/52/15 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 16.4 kN / C0 9.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205b",
      "7205B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5305S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5305S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 20.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.3,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "speed_oil_rpm": 10000,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5305S is the 25 mm bore member of NTN's heavy-duty 5300S double-row family, with a 62 mm outside diameter and 25.4 mm section width. Two fields make up the code — 53 is the double-row dimension series (heavy-duty 5300S double-row family) and 05 encodes the 25 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The radial section height here is 18.5 mm, and the catalogue couples that with C 32.5 kN / C0 20.7 kN. The 25/62/25.4 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 32.5/20.7 kN ratings and 1.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5305S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5305S?",
        "a": "5305S is a double-row angular contact ball bearing to ISO 15: 25 mm bore, 62 mm outside diameter, 25.4 mm width (0.984 x 2.441 x 1 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 32.5 kN, C0 20.7 kN and a 1.3 kN fatigue load limit Pu; the grease limiting speed is 7,500 r/min and the oil rating 10,000 r/min; mass about 350 g."
      },
      {
        "q": "How is the 5305S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 05 encodes the 25 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 62 mm OD and 25.4 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5305S support?",
        "a": "5305S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5305S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,500 r/min and the oil rating 10,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5305S?",
        "a": "The 25/62/25.4 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 32.5 kN / C0 20.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5305S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5305s",
      "5305S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5305SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5305SCLLD",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 25.2,
    "static_load_kN": 18.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 360,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5305SCLLD appears as a heavy-duty 5300S double-row family bearing of 25 mm bore, 62 mm outside diameter and 25.4 mm width. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 05 encodes the 25 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. NTN prints 25.2 kN dynamic and 18.2 kN static for this size and a 1.1 kN fatigue load limit Pu. Choose the heavy-duty 5300S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. A 25 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5305SCLLD without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5305SCLLD without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 25.2/18.2 kN ratings and 1.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5305SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5305SCLLD?",
        "a": "5305SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 62 mm outside diameter, 25.4 mm width (0.984 x 2.441 x 1 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 25.2 kN, C0 18.2 kN and a 1.1 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and no oil rating is printed for this execution; mass about 360 g."
      },
      {
        "q": "How is the 5305SCLLD designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 62 mm OD and 25.4 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5305SCLLD support?",
        "a": "5305SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5305SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5305SCLLD?",
        "a": "The 25/62/25.4 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 25.2 kN / C0 18.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5305SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5305sclld",
      "5305SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5305SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5305SCLLM",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 25.2,
    "static_load_kN": 18.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "speed_oil_rpm": 10000,
    "weight_g": 360,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 5300S double-row family entry 5305SCLLM carries a 25 mm bore in a 62 mm outside diameter, 25.4 mm wide envelope. Decoding 5305SCLLM: 53 is the double-row dimension series (heavy-duty 5300S double-row family), with 05 encodes the 25 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. Catalogue dynamic rating C is 25.2 kN against C0 18.2 kN — a C0/C ratio of 0.72 that is typical of an angular-contact contact ellipse. Choose the heavy-duty 5300S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 25 mm bore give the working limits. ",
    "applications": [
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 25.2/18.2 kN ratings and 1.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5305SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5305SCLLM?",
        "a": "5305SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 62 mm outside diameter, 25.4 mm width (0.984 x 2.441 x 1 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 25.2 kN, C0 18.2 kN and a 1.1 kN fatigue load limit Pu; the grease limiting speed is 7,500 r/min and the oil rating 10,000 r/min; mass about 360 g."
      },
      {
        "q": "How is the 5305SCLLM designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 62 mm OD and 25.4 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5305SCLLM support?",
        "a": "5305SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5305SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,500 r/min and the oil rating 10,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5305SCLLM?",
        "a": "The 25/62/25.4 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 25.2 kN / C0 18.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5305SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5305scllm",
      "5305SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5305SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5305SCZZ",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 25.2,
    "static_load_kN": 18.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "speed_oil_rpm": 10000,
    "weight_g": 360,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5305SCZZ appears as a heavy-duty 5300S double-row family bearing of 25 mm bore, 62 mm outside diameter and 25.4 mm width. The designation breaks down as 53 is the double-row dimension series (heavy-duty 5300S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The radial section height here is 18.5 mm, and the catalogue couples that with C 25.2 kN / C0 18.2 kN. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "precision instrument and encoder support shafts",
      "small machine-tool spindle and live-centre positions",
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "The 7,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 25.2/18.2 kN ratings and 1.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5305SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5305SCZZ?",
        "a": "5305SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 25 mm bore, 62 mm outside diameter, 25.4 mm width (0.984 x 2.441 x 1 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 25.2 kN, C0 18.2 kN and a 1.1 kN fatigue load limit Pu; the grease limiting speed is 7,500 r/min and the oil rating 10,000 r/min; mass about 360 g."
      },
      {
        "q": "How is the 5305SCZZ designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 05 encodes the 25 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 62 mm OD and 25.4 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5305SCZZ support?",
        "a": "5305SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5305SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,500 r/min and the oil rating 10,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5305SCZZ?",
        "a": "The 25/62/25.4 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 25.2 kN / C0 18.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5305SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5305sczz",
      "5305SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7305",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 29.3,
    "static_load_kN": 15.8,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.24,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 17000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 is the 25 mm bore member of NTN's heavy-duty 7300 single-row family, with a 62 mm outside diameter and 17 mm section width. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 230 g, which at this 18.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Against a deep-groove bearing of the same 25 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions",
      "small gearbox pinion shafts with helical gears",
      "precision instrument and encoder support shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 25 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 29.3/15.8 kN ratings and 1.24 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7305; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7305?",
        "a": "7305 is a single-row angular contact ball bearing to ISO 15: 25 mm bore, 62 mm outside diameter, 17 mm width (0.984 x 2.441 x 0.669 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 29.3 kN, C0 15.8 kN and a 1.24 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min; mass about 230 g."
      },
      {
        "q": "How is the 7305 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 05 encodes the 25 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 62 mm OD and 17 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7305 support?",
        "a": "One 7305 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7305?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7305?",
        "a": "The 25/62/17 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 29.3 kN / C0 15.8 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305",
      "7305-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7305B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 27,
    "static_load_kN": 14.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.14,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 234,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7305B belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 25 / 62 / 17 mm (bore / OD / width). Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 05 encodes the 25 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). NTN prints 27 kN dynamic and 14.6 kN static for this size and a 1.14 kN fatigue load limit Pu. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 11,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "high-speed router, grinder and woodworking spindles",
      "small pump and compressor shafts with combined load",
      "servo and stepper motor shafts with axial preload",
      "bicycle and motorcycle wheel and steering positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At 25 mm bore the rings are thin-sectioned: press force must go through the ring being fitted, never through the balls, or the first damage is already in the raceway before the machine runs.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The 11,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7305B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 27/14.6 kN ratings and 1.14 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7305B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7305B?",
        "a": "7305B is a single-row angular contact ball bearing to ISO 15: 25 mm bore, 62 mm outside diameter, 17 mm width (0.984 x 2.441 x 0.669 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 27 kN, C0 14.6 kN and a 1.14 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 234 g."
      },
      {
        "q": "How is the 7305B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 05 encodes the 25 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 62 mm OD and 17 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7305B support?",
        "a": "One 7305B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7305B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7305B?",
        "a": "The 25/62/17 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 27 kN / C0 14.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305b",
      "7305B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7906",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7906",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 47,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 8.35,
    "static_load_kN": 5.75,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "speed_oil_rpm": 19000,
    "weight_g": 58,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7906 is the 30 mm bore member of NTN's extra-light, high-speed 7900 single-row family, with a 47 mm outside diameter and 9 mm section width. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 14,000 r/min and the oil rating 19,000 r/min. For a 30 mm shaft with combined load, the practical shortlist is this series, its 7000-series standard section, and — where thrust reverses — a back-to-back pair rather than a single row. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 5.75 kN really covers the worst static case before substituting it for a 7000.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7906 without re-checking axial float, heat and housing width — the kinematics differ.",
      "On a 30 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The C0 of 5.75 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 8.35/5.75 kN ratings and 0.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7906; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7906?",
        "a": "7906 is a single-row angular contact ball bearing to ISO 15: 30 mm bore, 47 mm outside diameter, 9 mm width (1.181 x 1.85 x 0.354 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 8.35 kN, C0 5.75 kN and a 0.4 kN fatigue load limit Pu; the grease limiting speed is 14,000 r/min and the oil rating 19,000 r/min; mass about 58 g."
      },
      {
        "q": "How is the 7906 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 47 mm OD and 9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7906 support?",
        "a": "One 7906 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7906?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 14,000 r/min and the oil rating 19,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7906?",
        "a": "The 30/47/9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 8.35 kN / C0 5.75 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7906",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7906"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7006-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7006",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 55,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 15.4,
    "static_load_kN": 9.45,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.72,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 18000,
    "weight_g": 135,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7006 is the 30 mm bore member of NTN's standard-section 7000 single-row family, with a 55 mm outside diameter and 13 mm section width. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 9.45 kN static rating into useful one-direction thrust capacity. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 13,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 13,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The C0 of 9.45 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A 7006 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 15.4/9.45 kN ratings and 0.72 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7006; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7006?",
        "a": "7006 is a single-row angular contact ball bearing to ISO 15: 30 mm bore, 55 mm outside diameter, 13 mm width (1.181 x 2.165 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 15.4 kN, C0 9.45 kN and a 0.72 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 18,000 r/min; mass about 135 g."
      },
      {
        "q": "How is the 7006 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 55 mm OD and 13 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7006 support?",
        "a": "One 7006 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7006?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 18,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7006?",
        "a": "The 30/55/13 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 15.4 kN / C0 9.45 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7006",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=128",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7006",
      "7006-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5206S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5206S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 29.6,
    "static_load_kN": 21.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.3,
    "limiting_speed_rpm": 7100,
    "max_rpm": 7100,
    "speed_oil_rpm": 9500,
    "weight_g": 300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5206S carries a 30 mm bore in a 62 mm outside diameter, 23.8 mm wide envelope. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 06 encodes the 30 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The static margin, C0 21.1 kN versus C 29.6 kN, is what supports slow oscillating duty and shock without immediate brinelling. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 7,100 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5206S without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5206S without re-checking axial float, heat and housing width — the kinematics differ.",
      "Do not pair two random 5206S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 29.6/21.1 kN ratings and 1.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5206S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5206S?",
        "a": "5206S is a double-row angular contact ball bearing to ISO 15: 30 mm bore, 62 mm outside diameter, 23.8 mm width (1.181 x 2.441 x 0.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 29.6 kN, C0 21.1 kN and a 1.3 kN fatigue load limit Pu; the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min; mass about 300 g."
      },
      {
        "q": "How is the 5206S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 06 encodes the 30 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 62 mm OD and 23.8 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5206S support?",
        "a": "5206S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5206S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5206S?",
        "a": "The 30/62/23.8 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 29.6 kN / C0 21.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5206S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5206s",
      "5206S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5206SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5206SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 25.2,
    "static_load_kN": 18.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5206SCLLD measures 30 mm across the bore, 62 mm over the outer ring and 23.8 mm across the faces. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 06 encodes the 30 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. On speed, the grease limiting speed is 6,300 r/min and no oil rating is printed for this execution. Against a deep-groove bearing of the same 30 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Do not pair two random 5206SCLLD bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The C0 of 18.2 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 25.2/18.2 kN ratings and 1.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5206SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5206SCLLD?",
        "a": "5206SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 30 mm bore, 62 mm outside diameter, 23.8 mm width (1.181 x 2.441 x 0.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 25.2 kN, C0 18.2 kN and a 1.1 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and no oil rating is printed for this execution; mass about 300 g."
      },
      {
        "q": "How is the 5206SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 62 mm OD and 23.8 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5206SCLLD support?",
        "a": "5206SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5206SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5206SCLLD?",
        "a": "The 30/62/23.8 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 25.2 kN / C0 18.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5206SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5206sclld",
      "5206SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5206SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5206SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 25.2,
    "static_load_kN": 18.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 7100,
    "max_rpm": 7100,
    "speed_oil_rpm": 9500,
    "weight_g": 300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5206SCLLM appears as a medium-duty 5200S double-row family bearing of 30 mm bore, 62 mm outside diameter and 23.8 mm width. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The radial section height here is 16.0 mm, and the catalogue couples that with C 25.2 kN / C0 18.2 kN. Against a deep-groove bearing of the same 30 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 25.2/18.2 kN ratings and 1.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5206SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5206SCLLM?",
        "a": "5206SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 30 mm bore, 62 mm outside diameter, 23.8 mm width (1.181 x 2.441 x 0.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 25.2 kN, C0 18.2 kN and a 1.1 kN fatigue load limit Pu; the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min; mass about 300 g."
      },
      {
        "q": "How is the 5206SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 62 mm OD and 23.8 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5206SCLLM support?",
        "a": "5206SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5206SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5206SCLLM?",
        "a": "The 30/62/23.8 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 25.2 kN / C0 18.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5206SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5206scllm",
      "5206SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5206SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5206SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 25.2,
    "static_load_kN": 18.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.1,
    "limiting_speed_rpm": 7100,
    "max_rpm": 7100,
    "speed_oil_rpm": 9500,
    "weight_g": 300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5206SCZZ appears as a medium-duty 5200S double-row family bearing of 30 mm bore, 62 mm outside diameter and 23.8 mm width. Decoding 5206SCZZ: 52 is the double-row dimension series (medium-duty 5200S double-row family), with 06 encodes the 30 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. With C 25.2 kN and C0 18.2 kN, each mm of bore carries about 0.84 kN of dynamic rating. Against a deep-groove bearing of the same 30 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A 5206SCZZ mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "On a 30 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 25.2/18.2 kN ratings and 1.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5206SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5206SCZZ?",
        "a": "5206SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 30 mm bore, 62 mm outside diameter, 23.8 mm width (1.181 x 2.441 x 0.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 25.2 kN, C0 18.2 kN and a 1.1 kN fatigue load limit Pu; the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min; mass about 300 g."
      },
      {
        "q": "How is the 5206SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 62 mm OD and 23.8 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5206SCZZ support?",
        "a": "5206SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5206SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5206SCZZ?",
        "a": "The 30/62/23.8 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 25.2 kN / C0 18.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5206SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5206sczz",
      "5206SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7206",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 24.9,
    "static_load_kN": 14.8,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.16,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "speed_oil_rpm": 16000,
    "weight_g": 193,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 is the 30 mm bore member of NTN's medium-duty 7200 single-row family, with a 62 mm outside diameter and 16 mm section width. Decoding 7206: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. A 30 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 12,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 24.9/14.8 kN ratings and 1.16 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7206; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7206?",
        "a": "7206 is a single-row angular contact ball bearing to ISO 15: 30 mm bore, 62 mm outside diameter, 16 mm width (1.181 x 2.441 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 24.9 kN, C0 14.8 kN and a 1.16 kN fatigue load limit Pu; the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min; mass about 193 g."
      },
      {
        "q": "How is the 7206 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 62 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7206 support?",
        "a": "One 7206 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7206?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7206?",
        "a": "The 30/62/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 24.9 kN / C0 14.8 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206",
      "7206-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7206B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 22.7,
    "static_load_kN": 13.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.06,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 14000,
    "weight_g": 197,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206B is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 30 x 62 x 16 mm. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 06 encodes the 30 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 deg contact angle is the lever that turns the 13.5 kN static rating into useful one-direction thrust capacity. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "A 7206B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 22.7/13.5 kN ratings and 1.06 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7206B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7206B?",
        "a": "7206B is a single-row angular contact ball bearing to ISO 15: 30 mm bore, 62 mm outside diameter, 16 mm width (1.181 x 2.441 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 22.7 kN, C0 13.5 kN and a 1.06 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 14,000 r/min; mass about 197 g."
      },
      {
        "q": "How is the 7206B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 06 encodes the 30 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 62 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7206B support?",
        "a": "One 7206B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7206B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 14,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7206B?",
        "a": "The 30/62/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 22.7 kN / C0 13.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206b",
      "7206B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5306S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5306S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 40.5,
    "static_load_kN": 28.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8500,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5306S appears as a heavy-duty 5300S double-row family bearing of 30 mm bore, 72 mm outside diameter and 30.2 mm width. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 06 encodes the 30 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. On speed, the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min. Size selection is usually finished by checking that the C0 of 28.1 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Grease quantity matters as much as grade at 6,300 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The C0 of 28.1 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 40.5/28.1 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5306S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5306S?",
        "a": "5306S is a double-row angular contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 30.2 mm width (1.181 x 2.835 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 40.5 kN, C0 28.1 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min; mass about 570 g."
      },
      {
        "q": "How is the 5306S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 06 encodes the 30 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 72 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5306S support?",
        "a": "5306S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5306S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5306S?",
        "a": "The 30/72/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 40.5 kN / C0 28.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5306S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5306s",
      "5306S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5306SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5306SCLLD",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39,
    "static_load_kN": 28.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5306SCLLD appears as a heavy-duty 5300S double-row family bearing of 30 mm bore, 72 mm outside diameter and 30.2 mm width. The designation breaks down as 53 is the double-row dimension series (heavy-duty 5300S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. Catalogue mass is about 570 g, which at this 21.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Against a deep-groove bearing of the same 30 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 5,300 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "On a 30 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 39/28.7 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5306SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5306SCLLD?",
        "a": "5306SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 30.2 mm width (1.181 x 2.835 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 39 kN, C0 28.7 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 5,300 r/min and no oil rating is printed for this execution; mass about 570 g."
      },
      {
        "q": "How is the 5306SCLLD designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 72 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5306SCLLD support?",
        "a": "5306SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5306SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,300 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5306SCLLD?",
        "a": "The 30/72/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 39 kN / C0 28.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5306SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5306sclld",
      "5306SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5306SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5306SCLLM",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39,
    "static_load_kN": 28.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8500,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 5300S double-row family entry 5306SCLLM carries a 30 mm bore in a 72 mm outside diameter, 30.2 mm wide envelope. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 06 encodes the 30 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. NTN prints 39 kN dynamic and 28.7 kN static for this size and a 1.7 kN fatigue load limit Pu. Against a deep-groove bearing of the same 30 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 30 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Do not pair two random 5306SCLLM bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The C0 of 28.7 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5306SCLLM without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 39/28.7 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5306SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5306SCLLM?",
        "a": "5306SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 30.2 mm width (1.181 x 2.835 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 39 kN, C0 28.7 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min; mass about 570 g."
      },
      {
        "q": "How is the 5306SCLLM designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 72 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5306SCLLM support?",
        "a": "5306SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5306SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5306SCLLM?",
        "a": "The 30/72/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 39 kN / C0 28.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5306SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5306scllm",
      "5306SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5306SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5306SCZZ",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39,
    "static_load_kN": 28.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8500,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5306SCZZ belongs to the heavy-duty 5300S double-row family: the catalogue boundary dimensions read 30 / 72 / 30.2 mm (bore / OD / width). Two fields make up the code — 53 is the double-row dimension series (heavy-duty 5300S double-row family) and 06 encodes the 30 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The built-in back-to-back contact lines give the double-row bearing its two-direction thrust and moment capacity from one ring set. For a 30 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random 5306SCZZ bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A 5306SCZZ mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 39/28.7 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5306SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5306SCZZ?",
        "a": "5306SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 30.2 mm width (1.181 x 2.835 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 39 kN, C0 28.7 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min; mass about 570 g."
      },
      {
        "q": "How is the 5306SCZZ designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 06 encodes the 30 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 72 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5306SCZZ support?",
        "a": "5306SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5306SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5306SCZZ?",
        "a": "The 30/72/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 39 kN / C0 28.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5306SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5306sczz",
      "5306SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7306",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 37.5,
    "static_load_kN": 22.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.75,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 345,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7306 measures 30 mm across the bore, 72 mm over the outer ring and 19 mm across the faces. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 21.0 mm, and the catalogue couples that with C 37.5 kN / C0 22.3 kN. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 7306 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 37.5/22.3 kN ratings and 1.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7306; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7306?",
        "a": "7306 is a single-row angular contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 19 mm width (1.181 x 2.835 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 37.5 kN, C0 22.3 kN and a 1.75 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 345 g."
      },
      {
        "q": "How is the 7306 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 06 encodes the 30 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 72 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7306 support?",
        "a": "One 7306 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7306?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7306?",
        "a": "The 30/72/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 37.5 kN / C0 22.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306",
      "7306-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7306B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 34,
    "static_load_kN": 20.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.61,
    "limiting_speed_rpm": 9600,
    "max_rpm": 9600,
    "speed_oil_rpm": 13000,
    "weight_g": 352,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306B is the 30 mm bore member of NTN's heavy-duty 7300 single-row family, with a 72 mm outside diameter and 19 mm section width. Decoding 7306B: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 06 encodes the 30 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 352 g, which at this 21.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 9,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 34/20.5 kN ratings and 1.61 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7306B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7306B?",
        "a": "7306B is a single-row angular contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 19 mm width (1.181 x 2.835 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 34 kN, C0 20.5 kN and a 1.61 kN fatigue load limit Pu; the grease limiting speed is 9,600 r/min and the oil rating 13,000 r/min; mass about 352 g."
      },
      {
        "q": "How is the 7306B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 06 encodes the 30 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 72 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7306B support?",
        "a": "One 7306B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7306B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,600 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7306B?",
        "a": "The 30/72/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 34 kN / C0 20.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306b",
      "7306B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ306",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ306",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 57.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 2.46,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "speed_oil_rpm": 11000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 30 x 72 x 19 mm, NTN QJ306 sits in the heavy-duty QJ300 four-point family of the angular-contact programme. Reading the code: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), the last two digits 06 give the bore by the standard code table (30 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 30 mm bore give the working limits. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 30 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A QJ306 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 8,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 44/57.5 kN ratings and 2.46 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ306; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ306?",
        "a": "QJ306 is a four-point contact ball bearing to ISO 15: 30 mm bore, 72 mm outside diameter, 19 mm width (1.181 x 2.835 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 57.5 kN and a 2.46 kN fatigue load limit Pu; the grease limiting speed is 8,000 r/min and the oil rating 11,000 r/min; mass about 420 g."
      },
      {
        "q": "How is the QJ306 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 06 give the bore by the standard code table (30 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 72 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ306 support?",
        "a": "QJ306 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ306?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,000 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ306?",
        "a": "The 30/72/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 57.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ306",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj306",
      "QJ306"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7907",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7907",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 55,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 13.3,
    "static_load_kN": 8.85,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 0.64,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "speed_oil_rpm": 17000,
    "weight_g": 88,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the extra-light, high-speed 7900 single-row family, 7907 measures 35 mm across the bore, 55 mm over the outer ring and 10 mm across the faces. Decoding 7907: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 13.3 kN and C0 8.85 kN, each mm of bore carries about 0.38 kN of dynamic rating. Against a deep-groove bearing of the same 35 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 35 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 8.85 kN really covers the worst static case before substituting it for a 7000.",
      "The C0 of 8.85 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 13.3/8.85 kN ratings and 0.64 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7907; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7907?",
        "a": "7907 is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 55 mm outside diameter, 10 mm width (1.378 x 2.165 x 0.394 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 13.3 kN, C0 8.85 kN and a 0.64 kN fatigue load limit Pu; the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min; mass about 88 g."
      },
      {
        "q": "How is the 7907 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 55 mm OD and 10 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7907 support?",
        "a": "One 7907 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7907?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 13,000 r/min and the oil rating 17,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7907?",
        "a": "The 35/55/10 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 13.3 kN / C0 8.85 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7907",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7907"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7007-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7007",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 62,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.4,
    "static_load_kN": 12.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 0.95,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "speed_oil_rpm": 16000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the standard-section 7000 single-row family, 7007 measures 35 mm across the bore, 62 mm over the outer ring and 14 mm across the faces. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min. For a 35 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. Grease quantity matters as much as grade at 12,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 12,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The C0 of 12.6 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 19.4/12.6 kN ratings and 0.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7007; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7007?",
        "a": "7007 is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 62 mm outside diameter, 14 mm width (1.378 x 2.441 x 0.551 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.4 kN, C0 12.6 kN and a 0.95 kN fatigue load limit Pu; the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min; mass about 180 g."
      },
      {
        "q": "How is the 7007 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 62 mm OD and 14 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7007 support?",
        "a": "One 7007 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7007?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 12,000 r/min and the oil rating 16,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7007?",
        "a": "The 35/62/14 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.4 kN / C0 12.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7007",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7007",
      "7007-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5207S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5207S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39,
    "static_load_kN": 28.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8000,
    "weight_g": 460,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5207S measures 35 mm across the bore, 72 mm over the outer ring and 27 mm across the faces. Decoding 5207S: 52 is the double-row dimension series (medium-duty 5200S double-row family), with 07 encodes the 35 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Catalogue dynamic rating C is 39 kN against C0 28.7 kN — a C0/C ratio of 0.74 that is typical of an angular-contact contact ellipse. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 39/28.7 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5207S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5207S?",
        "a": "5207S is a double-row angular contact ball bearing to ISO 15: 35 mm bore, 72 mm outside diameter, 27 mm width (1.378 x 2.835 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 39 kN, C0 28.7 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,000 r/min; mass about 460 g."
      },
      {
        "q": "How is the 5207S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 07 encodes the 35 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 72 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5207S support?",
        "a": "5207S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5207S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5207S?",
        "a": "The 35/72/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 39 kN / C0 28.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5207S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5207s",
      "5207S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5207SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5207SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 34,
    "static_load_kN": 25.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 460,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5207SCLLD measures 35 mm across the bore, 72 mm over the outer ring and 27 mm across the faces. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. NTN prints 34 kN dynamic and 25.3 kN static for this size and a 1.5 kN fatigue load limit Pu. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5207SCLLD without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 34/25.3 kN ratings and 1.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5207SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5207SCLLD?",
        "a": "5207SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 35 mm bore, 72 mm outside diameter, 27 mm width (1.378 x 2.835 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 34 kN, C0 25.3 kN and a 1.5 kN fatigue load limit Pu; the grease limiting speed is 5,300 r/min and no oil rating is printed for this execution; mass about 460 g."
      },
      {
        "q": "How is the 5207SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 72 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5207SCLLD support?",
        "a": "5207SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5207SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,300 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5207SCLLD?",
        "a": "The 35/72/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 34 kN / C0 25.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5207SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5207sclld",
      "5207SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5207SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5207SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 34,
    "static_load_kN": 25.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8500,
    "weight_g": 460,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5207SCLLM appears as a medium-duty 5200S double-row family bearing of 35 mm bore, 72 mm outside diameter and 27 mm width. NTN builds the number from 52 is the double-row dimension series (medium-duty 5200S double-row family), then 07 encodes the 35 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. Catalogue dynamic rating C is 34 kN against C0 25.3 kN — a C0/C ratio of 0.74 that is typical of an angular-contact contact ellipse. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5207SCLLM without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 34/25.3 kN ratings and 1.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5207SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5207SCLLM?",
        "a": "5207SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 35 mm bore, 72 mm outside diameter, 27 mm width (1.378 x 2.835 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 34 kN, C0 25.3 kN and a 1.5 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min; mass about 460 g."
      },
      {
        "q": "How is the 5207SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 72 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5207SCLLM support?",
        "a": "5207SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5207SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5207SCLLM?",
        "a": "The 35/72/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 34 kN / C0 25.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5207SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5207scllm",
      "5207SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5207SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5207SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 34,
    "static_load_kN": 25.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8500,
    "weight_g": 460,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5207SCZZ belongs to the medium-duty 5200S double-row family: the catalogue boundary dimensions read 35 / 72 / 27 mm (bore / OD / width). The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The static margin, C0 25.3 kN versus C 34 kN, is what supports slow oscillating duty and shock without immediate brinelling. Choose the medium-duty 5200S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5207SCZZ without re-checking axial float, heat and housing width — the kinematics differ.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random 5207SCZZ bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 34/25.3 kN ratings and 1.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5207SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5207SCZZ?",
        "a": "5207SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 35 mm bore, 72 mm outside diameter, 27 mm width (1.378 x 2.835 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 34 kN, C0 25.3 kN and a 1.5 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min; mass about 460 g."
      },
      {
        "q": "How is the 5207SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 72 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5207SCZZ support?",
        "a": "5207SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5207SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5207SCZZ?",
        "a": "The 35/72/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 34 kN / C0 25.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5207SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5207sczz",
      "5207SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7207",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 33,
    "static_load_kN": 20.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.57,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 14000,
    "weight_g": 281,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7207 measures 35 mm across the bore, 72 mm over the outer ring and 17 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 281 g, which at this 18.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Size selection is usually finished by checking that the C0 of 20.1 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. A 35 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 20.1 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Grease rated for deep-groove motor duty is not automatically right at 11,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 33/20.1 kN ratings and 1.57 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7207; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7207?",
        "a": "7207 is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 72 mm outside diameter, 17 mm width (1.378 x 2.835 x 0.669 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 33 kN, C0 20.1 kN and a 1.57 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 14,000 r/min; mass about 281 g."
      },
      {
        "q": "How is the 7207 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 72 mm OD and 17 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7207 support?",
        "a": "One 7207 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7207?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 14,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7207?",
        "a": "The 35/72/17 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 33 kN / C0 20.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207",
      "7207-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7207B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 30,
    "static_load_kN": 18.4,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.44,
    "limiting_speed_rpm": 9300,
    "max_rpm": 9300,
    "speed_oil_rpm": 12000,
    "weight_g": 287,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7207B carries a 35 mm bore in a 72 mm outside diameter, 17 mm wide envelope. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 07 encodes the 35 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). With C 30 kN and C0 18.4 kN, each mm of bore carries about 0.86 kN of dynamic rating. For a 35 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. Heat-mounting to 80-90 deg C is the clean route onto a 35 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7207B without re-checking axial float, heat and housing width — the kinematics differ.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 30/18.4 kN ratings and 1.44 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7207B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7207B?",
        "a": "7207B is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 72 mm outside diameter, 17 mm width (1.378 x 2.835 x 0.669 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 30 kN, C0 18.4 kN and a 1.44 kN fatigue load limit Pu; the grease limiting speed is 9,300 r/min and the oil rating 12,000 r/min; mass about 287 g."
      },
      {
        "q": "How is the 7207B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 07 encodes the 35 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 72 mm OD and 17 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7207B support?",
        "a": "One 7207B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7207B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,300 r/min and the oil rating 12,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7207B?",
        "a": "The 35/72/17 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 30 kN / C0 18.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207b",
      "7207B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5307S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5307S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 51,
    "static_load_kN": 36,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.2,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7500,
    "weight_g": 760,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 35 x 80 x 34.9 mm, NTN 5307S sits in the heavy-duty 5300S double-row family of the angular-contact programme. Reading the code: 53 is the double-row dimension series (heavy-duty 5300S double-row family), 07 encodes the 35 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The static margin, C0 36 kN versus C 51 kN, is what supports slow oscillating duty and shock without immediate brinelling. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 5,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 5307S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 51/36 kN ratings and 2.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5307S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5307S?",
        "a": "5307S is a double-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 34.9 mm width (1.378 x 3.15 x 1.374 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 51 kN, C0 36 kN and a 2.2 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min; mass about 760 g."
      },
      {
        "q": "How is the 5307S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 07 encodes the 35 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 80 mm OD and 34.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5307S support?",
        "a": "5307S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5307S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5307S?",
        "a": "The 35/80/34.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 51 kN / C0 36 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5307S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5307s",
      "5307S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5307SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5307SCLLD",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 33.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5307SCLLD appears as a heavy-duty 5300S double-row family bearing of 35 mm bore, 80 mm outside diameter and 34.9 mm width. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 07 encodes the 35 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The grease limiting speed is 4,800 r/min and no oil rating is printed for this execution. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. A 35 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,800 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 44/33.5 kN ratings and 2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5307SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5307SCLLD?",
        "a": "5307SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 34.9 mm width (1.378 x 3.15 x 1.374 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 33.5 kN and a 2 kN fatigue load limit Pu; the grease limiting speed is 4,800 r/min and no oil rating is printed for this execution; mass about 790 g."
      },
      {
        "q": "How is the 5307SCLLD designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 80 mm OD and 34.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5307SCLLD support?",
        "a": "5307SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5307SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,800 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5307SCLLD?",
        "a": "The 35/80/34.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 33.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5307SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5307sclld",
      "5307SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5307SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5307SCLLM",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 33.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7500,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 5300S double-row family entry 5307SCLLM carries a 35 mm bore in a 80 mm outside diameter, 34.9 mm wide envelope. Decoding 5307SCLLM: 53 is the double-row dimension series (heavy-duty 5300S double-row family), with 07 encodes the 35 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. With C 44 kN and C0 33.5 kN, each mm of bore carries about 1.26 kN of dynamic rating. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 35 mm bore give the working limits. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A 5307SCLLM mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 5,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 44/33.5 kN ratings and 2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5307SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5307SCLLM?",
        "a": "5307SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 34.9 mm width (1.378 x 3.15 x 1.374 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 33.5 kN and a 2 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min; mass about 790 g."
      },
      {
        "q": "How is the 5307SCLLM designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 80 mm OD and 34.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5307SCLLM support?",
        "a": "5307SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5307SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5307SCLLM?",
        "a": "The 35/80/34.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 33.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5307SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5307scllm",
      "5307SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5307SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5307SCZZ",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 33.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7500,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5307SCZZ appears as a heavy-duty 5300S double-row family bearing of 35 mm bore, 80 mm outside diameter and 34.9 mm width. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 07 encodes the 35 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. With C 44 kN and C0 33.5 kN, each mm of bore carries about 1.26 kN of dynamic rating. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Heat-mounting to 80-90 deg C is the clean route onto a 35 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A 5307SCZZ mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 33.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "On a 35 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 44/33.5 kN ratings and 2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5307SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5307SCZZ?",
        "a": "5307SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 34.9 mm width (1.378 x 3.15 x 1.374 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 33.5 kN and a 2 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min; mass about 790 g."
      },
      {
        "q": "How is the 5307SCZZ designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 07 encodes the 35 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 80 mm OD and 34.9 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5307SCZZ support?",
        "a": "5307SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5307SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5307SCZZ?",
        "a": "The 35/80/34.9 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 33.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5307SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5307sczz",
      "5307SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7307",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 26.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.05,
    "limiting_speed_rpm": 9800,
    "max_rpm": 9800,
    "speed_oil_rpm": 13000,
    "weight_g": 462,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 35 x 80 x 21 mm. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 26.3 kN static rating into useful one-direction thrust capacity. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 7307 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 44/26.3 kN ratings and 2.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7307; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7307?",
        "a": "7307 is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 21 mm width (1.378 x 3.15 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 26.3 kN and a 2.05 kN fatigue load limit Pu; the grease limiting speed is 9,800 r/min and the oil rating 13,000 r/min; mass about 462 g."
      },
      {
        "q": "How is the 7307 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 80 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7307 support?",
        "a": "One 7307 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7307?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,800 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7307?",
        "a": "The 35/80/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 26.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307",
      "7307-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7307B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 40.5,
    "static_load_kN": 24.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.89,
    "limiting_speed_rpm": 8400,
    "max_rpm": 8400,
    "speed_oil_rpm": 11000,
    "weight_g": 469,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7307B appears as a heavy-duty 7300 single-row family bearing of 35 mm bore, 80 mm outside diameter and 21 mm width. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 07 encodes the 35 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 deg contact angle is the lever that turns the 24.2 kN static rating into useful one-direction thrust capacity. The 35/80/21 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Heat-mounting to 80-90 deg C is the clean route onto a 35 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 8,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A 7307B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A 7307B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 40.5/24.2 kN ratings and 1.89 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7307B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7307B?",
        "a": "7307B is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 21 mm width (1.378 x 3.15 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 40.5 kN, C0 24.2 kN and a 1.89 kN fatigue load limit Pu; the grease limiting speed is 8,400 r/min and the oil rating 11,000 r/min; mass about 469 g."
      },
      {
        "q": "How is the 7307B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 07 encodes the 35 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 80 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7307B support?",
        "a": "One 7307B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7307B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,400 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7307B?",
        "a": "The 35/80/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 40.5 kN / C0 24.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307b",
      "7307B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ307",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ307",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 55,
    "static_load_kN": 73,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.15,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "speed_oil_rpm": 9300,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ307 is the 35 mm bore member of NTN's heavy-duty QJ300 four-point family, with a 80 mm outside diameter and 21 mm section width. Two fields make up the code — QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family) and the last two digits 07 give the bore by the standard code table (35 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Catalogue mass is about 570 g, which at this 22.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Choose the heavy-duty QJ300 four-point family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Heat-mounting to 80-90 deg C is the clean route onto a 35 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A QJ307 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 7,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 55/73 kN ratings and 3.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ307; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ307?",
        "a": "QJ307 is a four-point contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 21 mm width (1.378 x 3.15 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 55 kN, C0 73 kN and a 3.15 kN fatigue load limit Pu; the grease limiting speed is 7,000 r/min and the oil rating 9,300 r/min; mass about 570 g."
      },
      {
        "q": "How is the QJ307 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 07 give the bore by the standard code table (35 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 80 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ307 support?",
        "a": "QJ307 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ307?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,000 r/min and the oil rating 9,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ307?",
        "a": "The 35/80/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 55 kN / C0 73 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ307",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj307",
      "QJ307"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7908",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7908",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 62,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 14,
    "static_load_kN": 10.2,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 0.7,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "speed_oil_rpm": 15000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7908 is an NTN single-row angular contact ball bearing: extra-light, high-speed 7900 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 40 x 62 x 12 mm. NTN builds the number from 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), then 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 10.2 kN versus C 14 kN, is what supports slow oscillating duty and shock without immediate brinelling. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 10.2 kN really covers the worst static case before substituting it for a 7000.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7908 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Do not pair two random 7908 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 14/10.2 kN ratings and 0.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7908; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7908?",
        "a": "7908 is a single-row angular contact ball bearing to ISO 15: 40 mm bore, 62 mm outside diameter, 12 mm width (1.575 x 2.441 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 14 kN, C0 10.2 kN and a 0.7 kN fatigue load limit Pu; the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min; mass about 130 g."
      },
      {
        "q": "How is the 7908 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 62 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7908 support?",
        "a": "One 7908 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7908?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 11,000 r/min and the oil rating 15,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7908?",
        "a": "The 40/62/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 14 kN / C0 10.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7908",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7908"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7008-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7008",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 68,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 20.8,
    "static_load_kN": 14.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.07,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 14000,
    "weight_g": 222,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7008 is the 40 mm bore member of NTN's standard-section 7000 single-row family, with a 68 mm outside diameter and 15 mm section width. NTN builds the number from 70 is the single-row dimension series (standard-section 7000 single-row family), then 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 14.6 kN versus C 20.8 kN, is what supports slow oscillating duty and shock without immediate brinelling. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 40 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7008 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 10,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 7008 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 20.8/14.6 kN ratings and 1.07 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7008; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7008?",
        "a": "7008 is a single-row angular contact ball bearing to ISO 15: 40 mm bore, 68 mm outside diameter, 15 mm width (1.575 x 2.677 x 0.591 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 20.8 kN, C0 14.6 kN and a 1.07 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 14,000 r/min; mass about 222 g."
      },
      {
        "q": "How is the 7008 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 68 mm OD and 15 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7008 support?",
        "a": "One 7008 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7008?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 14,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7008?",
        "a": "The 40/68/15 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 20.8 kN / C0 14.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7008",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7008",
      "7008-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5208S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5208S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 33.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7100,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5208S belongs to the medium-duty 5200S double-row family: the catalogue boundary dimensions read 40 / 80 / 30.2 mm (bore / OD / width). The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 08 encodes the 40 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. NTN prints 44 kN dynamic and 33.5 kN static for this size and a 2 kN fatigue load limit Pu. The 40/80/30.2 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Heat-mounting to 80-90 deg C is the clean route onto a 40 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Do not pair two random 5208S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5208S without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 44/33.5 kN ratings and 2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5208S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5208S?",
        "a": "5208S is a double-row angular contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 30.2 mm width (1.575 x 3.15 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 33.5 kN and a 2 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,100 r/min; mass about 620 g."
      },
      {
        "q": "How is the 5208S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 08 encodes the 40 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 80 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5208S support?",
        "a": "5208S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5208S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5208S?",
        "a": "The 40/80/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 33.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5208S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5208s",
      "5208S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5208SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5208SCLLD",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 36.5,
    "static_load_kN": 29,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 40 x 80 x 30.2 mm, NTN 5208SCLLD sits in the medium-duty 5200S double-row family of the angular-contact programme. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 08 encodes the 40 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The radial section height here is 20.0 mm, and the catalogue couples that with C 36.5 kN / C0 29 kN. Choose the medium-duty 5200S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 36.5/29 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5208SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5208SCLLD?",
        "a": "5208SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 30.2 mm width (1.575 x 3.15 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 36.5 kN, C0 29 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 4,800 r/min and no oil rating is printed for this execution; mass about 630 g."
      },
      {
        "q": "How is the 5208SCLLD designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 80 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5208SCLLD support?",
        "a": "5208SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5208SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,800 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5208SCLLD?",
        "a": "The 40/80/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 36.5 kN / C0 29 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5208SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5208sclld",
      "5208SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5208SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5208SCLLM",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 36.5,
    "static_load_kN": 29,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7100,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5208SCLLM measures 40 mm across the bore, 80 mm over the outer ring and 30.2 mm across the faces. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Choose the medium-duty 5200S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "A 5208SCLLM mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,600 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 5,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 36.5/29 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5208SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5208SCLLM?",
        "a": "5208SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 30.2 mm width (1.575 x 3.15 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 36.5 kN, C0 29 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,100 r/min; mass about 630 g."
      },
      {
        "q": "How is the 5208SCLLM designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 80 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5208SCLLM support?",
        "a": "5208SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5208SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5208SCLLM?",
        "a": "The 40/80/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 36.5 kN / C0 29 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5208SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5208scllm",
      "5208SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5208SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5208SCZZ",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 36.5,
    "static_load_kN": 29,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.7,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7100,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5208SCZZ appears as a medium-duty 5200S double-row family bearing of 40 mm bore, 80 mm outside diameter and 30.2 mm width. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 08 encodes the 40 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. Catalogue dynamic rating C is 36.5 kN against C0 29 kN — a C0/C ratio of 0.79 that is typical of an angular-contact contact ellipse. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 40 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Do not pair two random 5208SCZZ bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 36.5/29 kN ratings and 1.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5208SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5208SCZZ?",
        "a": "5208SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 30.2 mm width (1.575 x 3.15 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 36.5 kN, C0 29 kN and a 1.7 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,100 r/min; mass about 630 g."
      },
      {
        "q": "How is the 5208SCZZ designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 80 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5208SCZZ support?",
        "a": "5208SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5208SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5208SCZZ?",
        "a": "The 40/80/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 36.5 kN / C0 29 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5208SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5208sczz",
      "5208SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7208",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39,
    "static_load_kN": 25.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.97,
    "limiting_speed_rpm": 9600,
    "max_rpm": 9600,
    "speed_oil_rpm": 13000,
    "weight_g": 355,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 40 x 80 x 18 mm. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 20.0 mm, and the catalogue couples that with C 39 kN / C0 25.1 kN. The 40/80/18 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. A 40 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 9,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 39/25.1 kN ratings and 1.97 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7208; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7208?",
        "a": "7208 is a single-row angular contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 18 mm width (1.575 x 3.15 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 39 kN, C0 25.1 kN and a 1.97 kN fatigue load limit Pu; the grease limiting speed is 9,600 r/min and the oil rating 13,000 r/min; mass about 355 g."
      },
      {
        "q": "How is the 7208 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 80 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7208 support?",
        "a": "One 7208 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7208?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,600 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7208?",
        "a": "The 40/80/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 39 kN / C0 25.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208",
      "7208-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7208B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 23,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 8300,
    "max_rpm": 8300,
    "speed_oil_rpm": 11000,
    "weight_g": 375,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7208B measures 40 mm across the bore, 80 mm over the outer ring and 18 mm across the faces. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 08 encodes the 40 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The oil rating of 11,000 r/min sits 2,700 r/min above the 8,300 r/min grease figure — a 1.33x step that says how much headroom oil cooling buys. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 40 mm bore give the working limits. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Grease rated for deep-groove motor duty is not automatically right at 8,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 35.5/23 kN ratings and 1.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7208B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7208B?",
        "a": "7208B is a single-row angular contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 18 mm width (1.575 x 3.15 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 35.5 kN, C0 23 kN and a 1.8 kN fatigue load limit Pu; the grease limiting speed is 8,300 r/min and the oil rating 11,000 r/min; mass about 375 g."
      },
      {
        "q": "How is the 7208B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 08 encodes the 40 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 80 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7208B support?",
        "a": "One 7208B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7208B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,300 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7208B?",
        "a": "The 40/80/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 35.5 kN / C0 23 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208b",
      "7208B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ208",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ208",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 49,
    "static_load_kN": 70.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.05,
    "limiting_speed_rpm": 6900,
    "max_rpm": 6900,
    "speed_oil_rpm": 9200,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 40 x 80 x 18 mm, NTN QJ208 sits in the medium-duty QJ200 four-point family of the angular-contact programme. NTN builds the number from QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), then the last two digits 08 give the bore by the standard code table (40 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. NTN prints 49 kN dynamic and 70.5 kN static for this size and a 3.05 kN fatigue load limit Pu. For a 40 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 6,900 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ208 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 49/70.5 kN ratings and 3.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ208; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ208?",
        "a": "QJ208 is a four-point contact ball bearing to ISO 15: 40 mm bore, 80 mm outside diameter, 18 mm width (1.575 x 3.15 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 49 kN, C0 70.5 kN and a 3.05 kN fatigue load limit Pu; the grease limiting speed is 6,900 r/min and the oil rating 9,200 r/min; mass about 450 g."
      },
      {
        "q": "How is the QJ208 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 08 give the bore by the standard code table (40 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 80 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ208 support?",
        "a": "QJ208 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ208?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,900 r/min and the oil rating 9,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ208?",
        "a": "The 40/80/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 49 kN / C0 70.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ208",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj208",
      "QJ208"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5308S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5308S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 56.5,
    "static_load_kN": 41,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.5,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "speed_oil_rpm": 6700,
    "weight_g": 1030,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5308S is an NTN double-row angular contact ball bearing: heavy-duty 5300S double-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 40 x 90 x 36.5 mm. Decoding 5308S: 53 is the double-row dimension series (heavy-duty 5300S double-row family), with 08 encodes the 40 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Catalogue dynamic rating C is 56.5 kN against C0 41 kN — a C0/C ratio of 0.73 that is typical of an angular-contact contact ellipse. Choose the heavy-duty 5300S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Heat-mounting to 80-90 deg C is the clean route onto a 40 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "A 5308S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A 5308S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 56.5/41 kN ratings and 2.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5308S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5308S?",
        "a": "5308S is a double-row angular contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 36.5 mm width (1.575 x 3.543 x 1.437 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 56.5 kN, C0 41 kN and a 2.5 kN fatigue load limit Pu; the grease limiting speed is 5,300 r/min and the oil rating 6,700 r/min; mass about 1030 g."
      },
      {
        "q": "How is the 5308S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 08 encodes the 40 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 90 mm OD and 36.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5308S support?",
        "a": "5308S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5308S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,300 r/min and the oil rating 6,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5308S?",
        "a": "The 40/90/36.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 56.5 kN / C0 41 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5308S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5308s",
      "5308S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5308SCLLD",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5308SCLLD",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 38,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.3,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 1040,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 5300S double-row family, 5308SCLLD measures 40 mm across the bore, 90 mm over the outer ring and 36.5 mm across the faces. The designation breaks down as 53 is the double-row dimension series (heavy-duty 5300S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The built-in back-to-back contact lines give the double-row bearing its two-direction thrust and moment capacity from one ring set. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLD contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Do not pair two random 5308SCLLD bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 5308SCLLD mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 49.5/38 kN ratings and 2.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5308SCLLD; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5308SCLLD?",
        "a": "5308SCLLD is a sealed double-row angular contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 36.5 mm width (1.575 x 3.543 x 1.437 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 49.5 kN, C0 38 kN and a 2.3 kN fatigue load limit Pu; the grease limiting speed is 4,500 r/min and no oil rating is printed for this execution; mass about 1040 g."
      },
      {
        "q": "How is the 5308SCLLD designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CLLD marks the SC internal design with contact rubber seals on both sides. The 90 mm OD and 36.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5308SCLLD support?",
        "a": "5308SCLLD is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with contact rubber seals (grease-lubricated, no oil speed rating)."
      },
      {
        "q": "What lubrication speeds does NTN print for 5308SCLLD?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,500 r/min and no oil rating is printed for this execution. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5308SCLLD?",
        "a": "The 40/90/36.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 49.5 kN / C0 38 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5308SCLLD",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5308sclld",
      "5308SCLLD"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5308SCLLM",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5308SCLLM",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 38,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.3,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "speed_oil_rpm": 6700,
    "weight_g": 1040,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5308SCLLM appears as a heavy-duty 5300S double-row family bearing of 40 mm bore, 90 mm outside diameter and 36.5 mm width. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 08 encodes the 40 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. Catalogue mass is about 1040 g, which at this 25.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed LLM non-contact-seal executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 49.5/38 kN ratings and 2.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5308SCLLM; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5308SCLLM?",
        "a": "5308SCLLM is a sealed double-row angular contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 36.5 mm width (1.575 x 3.543 x 1.437 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 49.5 kN, C0 38 kN and a 2.3 kN fatigue load limit Pu; the grease limiting speed is 5,300 r/min and the oil rating 6,700 r/min; mass about 1040 g."
      },
      {
        "q": "How is the 5308SCLLM designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CLLM marks the SC internal design with non-contact rubber seals on both sides. The 90 mm OD and 36.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5308SCLLM support?",
        "a": "5308SCLLM is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with non-contact rubber seals that keep the shield-level speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5308SCLLM?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,300 r/min and the oil rating 6,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5308SCLLM?",
        "a": "The 40/90/36.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 49.5 kN / C0 38 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5308SCLLM",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5308scllm",
      "5308SCLLM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5308SCZZ",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5308SCZZ",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 38,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.3,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "speed_oil_rpm": 6700,
    "weight_g": 1040,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5308SCZZ belongs to the heavy-duty 5300S double-row family: the catalogue boundary dimensions read 40 / 90 / 36.5 mm (bore / OD / width). Reading the code: 53 is the double-row dimension series (heavy-duty 5300S double-row family), 08 encodes the 40 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The static margin, C0 38 kN versus C 49.5 kN, is what supports slow oscillating duty and shock without immediate brinelling. Against a deep-groove bearing of the same 40 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Heat-mounting to 80-90 deg C is the clean route onto a 40 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "Sealed ZZ shielded executions are grease-for-life: there is no relubrication path, so the grease life calculation replaces the relubrication plan.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5308SCZZ without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Do not pair two random 5308SCZZ bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 49.5/38 kN ratings and 2.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5308SCZZ; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5308SCZZ?",
        "a": "5308SCZZ is a sealed double-row angular contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 36.5 mm width (1.575 x 3.543 x 1.437 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 49.5 kN, C0 38 kN and a 2.3 kN fatigue load limit Pu; the grease limiting speed is 5,300 r/min and the oil rating 6,700 r/min; mass about 1040 g."
      },
      {
        "q": "How is the 5308SCZZ designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 08 encodes the 40 mm bore (bore code x 5), and CZZ marks the double-row SC internal design with pressed-steel shields on both sides. The 90 mm OD and 36.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5308SCZZ support?",
        "a": "5308SCZZ is a sealed double-row bearing: thrust in both directions, radial and moment load in one envelope, with pressed-steel shields that keep the open-bearing speed ratings."
      },
      {
        "q": "What lubrication speeds does NTN print for 5308SCZZ?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,300 r/min and the oil rating 6,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5308SCZZ?",
        "a": "The 40/90/36.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 49.5 kN / C0 38 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5308SCZZ",
        "equiv_brand": "ISO 15",
        "level": "verify",
        "note": "ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=136",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5308sczz",
      "5308SCZZ"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7308",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 54,
    "static_load_kN": 33,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.58,
    "limiting_speed_rpm": 8600,
    "max_rpm": 8600,
    "speed_oil_rpm": 12000,
    "weight_g": 625,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7308 measures 40 mm across the bore, 90 mm over the outer ring and 23 mm across the faces. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 54 kN and C0 33 kN, each mm of bore carries about 1.35 kN of dynamic rating. Size selection is usually finished by checking that the C0 of 33 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 33 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7308 without re-checking axial float, heat and housing width — the kinematics differ.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 54/33 kN ratings and 2.58 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7308; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7308?",
        "a": "7308 is a single-row angular contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 23 mm width (1.575 x 3.543 x 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 54 kN, C0 33 kN and a 2.58 kN fatigue load limit Pu; the grease limiting speed is 8,600 r/min and the oil rating 12,000 r/min; mass about 625 g."
      },
      {
        "q": "How is the 7308 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 08 encodes the 40 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 90 mm OD and 23 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7308 support?",
        "a": "One 7308 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7308?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,600 r/min and the oil rating 12,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7308?",
        "a": "The 40/90/23 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 54 kN / C0 33 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308",
      "7308-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7308B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 30.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.37,
    "limiting_speed_rpm": 7400,
    "max_rpm": 7400,
    "speed_oil_rpm": 9900,
    "weight_g": 636,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 40 x 90 x 23 mm, NTN 7308B sits in the heavy-duty 7300 single-row family of the angular-contact programme. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 08 encodes the 40 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). With C 49.5 kN and C0 30.5 kN, each mm of bore carries about 1.24 kN of dynamic rating. Size selection is usually finished by checking that the C0 of 30.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 40 mm bore give the working limits. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Do not pair two random 7308B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "On a 40 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 49.5/30.5 kN ratings and 2.37 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7308B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7308B?",
        "a": "7308B is a single-row angular contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 23 mm width (1.575 x 3.543 x 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 49.5 kN, C0 30.5 kN and a 2.37 kN fatigue load limit Pu; the grease limiting speed is 7,400 r/min and the oil rating 9,900 r/min; mass about 636 g."
      },
      {
        "q": "How is the 7308B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 08 encodes the 40 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 90 mm OD and 23 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7308B support?",
        "a": "One 7308B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7308B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,400 r/min and the oil rating 9,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7308B?",
        "a": "The 40/90/23 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 49.5 kN / C0 30.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308b",
      "7308B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ308",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ308",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 67,
    "static_load_kN": 91.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.95,
    "limiting_speed_rpm": 6200,
    "max_rpm": 6200,
    "speed_oil_rpm": 8200,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty QJ300 four-point family, QJ308 measures 40 mm across the bore, 90 mm over the outer ring and 23 mm across the faces. Decoding QJ308: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), with the last two digits 08 give the bore by the standard code table (40 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The radial section height here is 25.0 mm, and the catalogue couples that with C 67 kN / C0 91.5 kN. Size selection is usually finished by checking that the C0 of 91.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 40 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 67/91.5 kN ratings and 3.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ308; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ308?",
        "a": "QJ308 is a four-point contact ball bearing to ISO 15: 40 mm bore, 90 mm outside diameter, 23 mm width (1.575 x 3.543 x 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 67 kN, C0 91.5 kN and a 3.95 kN fatigue load limit Pu; the grease limiting speed is 6,200 r/min and the oil rating 8,200 r/min; mass about 780 g."
      },
      {
        "q": "How is the QJ308 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 08 give the bore by the standard code table (40 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 90 mm OD and 23 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ308 support?",
        "a": "QJ308 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ308?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,200 r/min and the oil rating 8,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ308?",
        "a": "The 40/90/23 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 67 kN / C0 91.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ308",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj308",
      "QJ308"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7909",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7909",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 68,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 17.4,
    "static_load_kN": 12.9,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 0.9,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "speed_oil_rpm": 14000,
    "weight_g": 150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7909 appears as a extra-light, high-speed 7900 single-row family bearing of 45 mm bore, 68 mm outside diameter and 12 mm width. The designation breaks down as 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 14,000 r/min sits 4,000 r/min above the 10,000 r/min grease figure — a 1.40x step that says how much headroom oil cooling buys. The 45/68/12 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 45 mm bore give the working limits. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 12.9 kN really covers the worst static case before substituting it for a 7000.",
      "A 7909 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 10,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 10,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 17.4/12.9 kN ratings and 0.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7909; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7909?",
        "a": "7909 is a single-row angular contact ball bearing to ISO 15: 45 mm bore, 68 mm outside diameter, 12 mm width (1.772 x 2.677 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 17.4 kN, C0 12.9 kN and a 0.9 kN fatigue load limit Pu; the grease limiting speed is 10,000 r/min and the oil rating 14,000 r/min; mass about 150 g."
      },
      {
        "q": "How is the 7909 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 68 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7909 support?",
        "a": "One 7909 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7909?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 10,000 r/min and the oil rating 14,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7909?",
        "a": "The 45/68/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 17.4 kN / C0 12.9 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7909",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7909"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7009-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7009",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 75,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 24.7,
    "static_load_kN": 17.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.29,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "speed_oil_rpm": 13000,
    "weight_g": 282,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the standard-section 7000 single-row family, 7009 measures 45 mm across the bore, 75 mm over the outer ring and 16 mm across the faces. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 13,000 r/min sits 3,500 r/min above the 9,500 r/min grease figure — a 1.37x step that says how much headroom oil cooling buys. Against a deep-groove bearing of the same 45 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 45 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7009 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 9,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 24.7/17.7 kN ratings and 1.29 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7009; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7009?",
        "a": "7009 is a single-row angular contact ball bearing to ISO 15: 45 mm bore, 75 mm outside diameter, 16 mm width (1.772 x 2.953 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 24.7 kN, C0 17.7 kN and a 1.29 kN fatigue load limit Pu; the grease limiting speed is 9,500 r/min and the oil rating 13,000 r/min; mass about 282 g."
      },
      {
        "q": "How is the 7009 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 75 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7009 support?",
        "a": "One 7009 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7009?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,500 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7009?",
        "a": "The 45/75/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 24.7 kN / C0 17.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7009",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7009",
      "7009-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5209S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5209S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 49.5,
    "static_load_kN": 38,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.3,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "speed_oil_rpm": 6700,
    "weight_g": 670,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5209S is the 45 mm bore member of NTN's medium-duty 5200S double-row family, with a 85 mm outside diameter and 30.2 mm section width. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 09 encodes the 45 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Catalogue mass is about 670 g, which at this 20.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Size selection is usually finished by checking that the C0 of 38 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 45 mm bore give the working limits. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The C0 of 38 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 49.5/38 kN ratings and 2.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5209S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5209S?",
        "a": "5209S is a double-row angular contact ball bearing to ISO 15: 45 mm bore, 85 mm outside diameter, 30.2 mm width (1.772 x 3.346 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 49.5 kN, C0 38 kN and a 2.3 kN fatigue load limit Pu; the grease limiting speed is 5,000 r/min and the oil rating 6,700 r/min; mass about 670 g."
      },
      {
        "q": "How is the 5209S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 09 encodes the 45 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 85 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5209S support?",
        "a": "5209S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5209S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,000 r/min and the oil rating 6,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5209S?",
        "a": "The 45/85/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 49.5 kN / C0 38 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5209S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5209s",
      "5209S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7209",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 44,
    "static_load_kN": 28.7,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.25,
    "limiting_speed_rpm": 8700,
    "max_rpm": 8700,
    "speed_oil_rpm": 12000,
    "weight_g": 404,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7209 measures 45 mm across the bore, 85 mm over the outer ring and 19 mm across the faces. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 44 kN against C0 28.7 kN — a C0/C ratio of 0.65 that is typical of an angular-contact contact ellipse. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 8,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 8,700 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 44/28.7 kN ratings and 2.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7209; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7209?",
        "a": "7209 is a single-row angular contact ball bearing to ISO 15: 45 mm bore, 85 mm outside diameter, 19 mm width (1.772 x 3.346 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 28.7 kN and a 2.25 kN fatigue load limit Pu; the grease limiting speed is 8,700 r/min and the oil rating 12,000 r/min; mass about 404 g."
      },
      {
        "q": "How is the 7209 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 85 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7209 support?",
        "a": "One 7209 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7209?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,700 r/min and the oil rating 12,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7209?",
        "a": "The 45/85/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 28.7 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209",
      "7209-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7209B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 40,
    "static_load_kN": 26.2,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.04,
    "limiting_speed_rpm": 7400,
    "max_rpm": 7400,
    "speed_oil_rpm": 9900,
    "weight_g": 410,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7209B belongs to the medium-duty 7200 single-row family: the catalogue boundary dimensions read 45 / 85 / 19 mm (bore / OD / width). Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 09 encodes the 45 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). At roughly 20.0 mm of radial section, the catalogue still quotes 40 kN dynamic capacity for the 45 mm bore. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Do not pair two random 7209B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 7,400 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 40/26.2 kN ratings and 2.04 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7209B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7209B?",
        "a": "7209B is a single-row angular contact ball bearing to ISO 15: 45 mm bore, 85 mm outside diameter, 19 mm width (1.772 x 3.346 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 40 kN, C0 26.2 kN and a 2.04 kN fatigue load limit Pu; the grease limiting speed is 7,400 r/min and the oil rating 9,900 r/min; mass about 410 g."
      },
      {
        "q": "How is the 7209B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 09 encodes the 45 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 85 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7209B support?",
        "a": "One 7209B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7209B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,400 r/min and the oil rating 9,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7209B?",
        "a": "The 45/85/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 40 kN / C0 26.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209b",
      "7209B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ209",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ209",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 55,
    "static_load_kN": 81,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.5,
    "limiting_speed_rpm": 6200,
    "max_rpm": 6200,
    "speed_oil_rpm": 8200,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ209 is the 45 mm bore member of NTN's medium-duty QJ200 four-point family, with a 85 mm outside diameter and 19 mm section width. The designation breaks down as QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 09 give the bore by the standard code table (45 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Against a deep-groove bearing of the same 45 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 6,200 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ209 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 6,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 55/81 kN ratings and 3.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ209; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ209?",
        "a": "QJ209 is a four-point contact ball bearing to ISO 15: 45 mm bore, 85 mm outside diameter, 19 mm width (1.772 x 3.346 x 0.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 55 kN, C0 81 kN and a 3.5 kN fatigue load limit Pu; the grease limiting speed is 6,200 r/min and the oil rating 8,200 r/min; mass about 520 g."
      },
      {
        "q": "How is the QJ209 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 09 give the bore by the standard code table (45 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 85 mm OD and 19 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ209 support?",
        "a": "QJ209 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ209?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,200 r/min and the oil rating 8,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ209?",
        "a": "The 45/85/19 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 55 kN / C0 81 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ209",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj209",
      "QJ209"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5309S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5309S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 68.5,
    "static_load_kN": 51,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.1,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "speed_oil_rpm": 6000,
    "weight_g": 1370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 5300S double-row family entry 5309S carries a 45 mm bore in a 100 mm outside diameter, 39.7 mm wide envelope. The designation breaks down as 53 is the double-row dimension series (heavy-duty 5300S double-row family); 09 encodes the 45 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. NTN prints 68.5 kN dynamic and 51 kN static for this size and a 3.1 kN fatigue load limit Pu. Against a deep-groove bearing of the same 45 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 45 mm bore give the working limits. ",
    "applications": [
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Do not pair two random 5309S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5309S without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 68.5/51 kN ratings and 3.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5309S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5309S?",
        "a": "5309S is a double-row angular contact ball bearing to ISO 15: 45 mm bore, 100 mm outside diameter, 39.7 mm width (1.772 x 3.937 x 1.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 68.5 kN, C0 51 kN and a 3.1 kN fatigue load limit Pu; the grease limiting speed is 4,500 r/min and the oil rating 6,000 r/min; mass about 1370 g."
      },
      {
        "q": "How is the 5309S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 09 encodes the 45 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 100 mm OD and 39.7 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5309S support?",
        "a": "5309S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5309S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,500 r/min and the oil rating 6,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5309S?",
        "a": "The 45/100/39.7 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 68.5 kN / C0 51 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5309S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5309s",
      "5309S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7309",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 70.5,
    "static_load_kN": 44,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.45,
    "limiting_speed_rpm": 7800,
    "max_rpm": 7800,
    "speed_oil_rpm": 10000,
    "weight_g": 837,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 45 x 100 x 25 mm. Decoding 7309: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 44 kN versus C 70.5 kN, is what supports slow oscillating duty and shock without immediate brinelling. The 45/100/25 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 7,800 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Do not pair two random 7309 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 70.5/44 kN ratings and 3.45 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7309; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7309?",
        "a": "7309 is a single-row angular contact ball bearing to ISO 15: 45 mm bore, 100 mm outside diameter, 25 mm width (1.772 x 3.937 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 70.5 kN, C0 44 kN and a 3.45 kN fatigue load limit Pu; the grease limiting speed is 7,800 r/min and the oil rating 10,000 r/min; mass about 837 g."
      },
      {
        "q": "How is the 7309 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 09 encodes the 45 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 100 mm OD and 25 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7309 support?",
        "a": "One 7309 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7309?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,800 r/min and the oil rating 10,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7309?",
        "a": "The 45/100/25 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 70.5 kN / C0 44 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309",
      "7309-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7309B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 64.5,
    "static_load_kN": 40.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.15,
    "limiting_speed_rpm": 6600,
    "max_rpm": 6600,
    "speed_oil_rpm": 8900,
    "weight_g": 854,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309B is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 45 x 100 x 25 mm. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 09 encodes the 45 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The oil rating of 8,900 r/min sits 2,300 r/min above the 6,600 r/min grease figure — a 1.35x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A 7309B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,600 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 64.5/40.5 kN ratings and 3.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7309B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7309B?",
        "a": "7309B is a single-row angular contact ball bearing to ISO 15: 45 mm bore, 100 mm outside diameter, 25 mm width (1.772 x 3.937 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 64.5 kN, C0 40.5 kN and a 3.15 kN fatigue load limit Pu; the grease limiting speed is 6,600 r/min and the oil rating 8,900 r/min; mass about 854 g."
      },
      {
        "q": "How is the 7309B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 09 encodes the 45 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 100 mm OD and 25 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7309B support?",
        "a": "One 7309B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7309B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,600 r/min and the oil rating 8,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7309B?",
        "a": "The 45/100/25 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 64.5 kN / C0 40.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309b",
      "7309B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ309",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ309",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 87,
    "static_load_kN": 121,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 5.2,
    "limiting_speed_rpm": 5500,
    "max_rpm": 5500,
    "speed_oil_rpm": 7400,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ309 is an NTN four-point contact ball bearing: heavy-duty QJ300 four-point family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 45 x 100 x 25 mm. NTN builds the number from QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), then the last two digits 09 give the bore by the standard code table (45 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 35 deg four-point geometry doubles the axial contact points, so the 87 kN rating is available for thrust in both directions. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 5,500 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 45 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 45 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A QJ309 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 87/121 kN ratings and 5.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ309; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ309?",
        "a": "QJ309 is a four-point contact ball bearing to ISO 15: 45 mm bore, 100 mm outside diameter, 25 mm width (1.772 x 3.937 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 87 kN, C0 121 kN and a 5.2 kN fatigue load limit Pu; the grease limiting speed is 5,500 r/min and the oil rating 7,400 r/min; mass about 1050 g."
      },
      {
        "q": "How is the QJ309 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 09 give the bore by the standard code table (45 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 100 mm OD and 25 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ309 support?",
        "a": "QJ309 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ309?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,500 r/min and the oil rating 7,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ309?",
        "a": "The 45/100/25 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 87 kN / C0 121 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ309",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj309",
      "QJ309"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7910",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7910",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 72,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 18.4,
    "static_load_kN": 14.5,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 0.98,
    "limiting_speed_rpm": 9200,
    "max_rpm": 9200,
    "speed_oil_rpm": 12000,
    "weight_g": 157,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7910 belongs to the extra-light, high-speed 7900 single-row family: the catalogue boundary dimensions read 50 / 72 / 12 mm (bore / OD / width). Decoding 7910: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Size selection is usually finished by checking that the C0 of 14.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 14.5 kN really covers the worst static case before substituting it for a 7000.",
      "The 9,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The C0 of 14.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 9,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 18.4/14.5 kN ratings and 0.98 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7910; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7910?",
        "a": "7910 is a single-row angular contact ball bearing to ISO 15: 50 mm bore, 72 mm outside diameter, 12 mm width (1.969 x 2.835 x 0.472 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 18.4 kN, C0 14.5 kN and a 0.98 kN fatigue load limit Pu; the grease limiting speed is 9,200 r/min and the oil rating 12,000 r/min; mass about 157 g."
      },
      {
        "q": "How is the 7910 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 72 mm OD and 12 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7910 support?",
        "a": "One 7910 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7910?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,200 r/min and the oil rating 12,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7910?",
        "a": "The 50/72/12 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 18.4 kN / C0 14.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7910",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7910"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7010-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7010",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 80,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 26.2,
    "static_load_kN": 20.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.42,
    "limiting_speed_rpm": 8600,
    "max_rpm": 8600,
    "speed_oil_rpm": 11000,
    "weight_g": 306,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7010 carries a 50 mm bore in a 80 mm outside diameter, 16 mm wide envelope. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 26.2 kN against C0 20.1 kN — a C0/C ratio of 0.77 that is typical of an angular-contact contact ellipse. Size selection is usually finished by checking that the C0 of 20.1 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7010 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 20.1 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 26.2/20.1 kN ratings and 1.42 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7010; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7010?",
        "a": "7010 is a single-row angular contact ball bearing to ISO 15: 50 mm bore, 80 mm outside diameter, 16 mm width (1.969 x 3.15 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 26.2 kN, C0 20.1 kN and a 1.42 kN fatigue load limit Pu; the grease limiting speed is 8,600 r/min and the oil rating 11,000 r/min; mass about 306 g."
      },
      {
        "q": "How is the 7010 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 80 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7010 support?",
        "a": "One 7010 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7010?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,600 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7010?",
        "a": "The 50/80/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 26.2 kN / C0 20.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7010",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7010",
      "7010-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5210S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5210S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 53,
    "static_load_kN": 43.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.7,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "speed_oil_rpm": 6000,
    "weight_g": 720,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5210S appears as a medium-duty 5200S double-row family bearing of 50 mm bore, 90 mm outside diameter and 30.2 mm width. Decoding 5210S: 52 is the double-row dimension series (medium-duty 5200S double-row family), with 10 encodes the 50 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Catalogue dynamic rating C is 53 kN against C0 43.5 kN — a C0/C ratio of 0.82 that is typical of an angular-contact contact ellipse. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "A 5210S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 4,800 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 53/43.5 kN ratings and 2.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5210S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5210S?",
        "a": "5210S is a double-row angular contact ball bearing to ISO 15: 50 mm bore, 90 mm outside diameter, 30.2 mm width (1.969 x 3.543 x 1.189 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 53 kN, C0 43.5 kN and a 2.7 kN fatigue load limit Pu; the grease limiting speed is 4,800 r/min and the oil rating 6,000 r/min; mass about 720 g."
      },
      {
        "q": "How is the 5210S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 10 encodes the 50 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 90 mm OD and 30.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5210S support?",
        "a": "5210S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5210S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,800 r/min and the oil rating 6,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5210S?",
        "a": "The 50/90/30.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 53 kN / C0 43.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5210S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5210s",
      "5210S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7210",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 45.5,
    "static_load_kN": 31.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.46,
    "limiting_speed_rpm": 7900,
    "max_rpm": 7900,
    "speed_oil_rpm": 10000,
    "weight_g": 457,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7210 carries a 50 mm bore in a 90 mm outside diameter, 20 mm wide envelope. Decoding 7210: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 20.0 mm of radial section, the catalogue still quotes 45.5 kN dynamic capacity for the 50 mm bore. Against a deep-groove bearing of the same 50 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 7,900 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 7,900 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 7210 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 45.5/31.5 kN ratings and 2.46 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7210; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7210?",
        "a": "7210 is a single-row angular contact ball bearing to ISO 15: 50 mm bore, 90 mm outside diameter, 20 mm width (1.969 x 3.543 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 45.5 kN, C0 31.5 kN and a 2.46 kN fatigue load limit Pu; the grease limiting speed is 7,900 r/min and the oil rating 10,000 r/min; mass about 457 g."
      },
      {
        "q": "How is the 7210 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 90 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7210 support?",
        "a": "One 7210 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7210?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,900 r/min and the oil rating 10,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7210?",
        "a": "The 50/90/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 45.5 kN / C0 31.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210",
      "7210-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7210B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 28.6,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.16,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "speed_oil_rpm": 9000,
    "weight_g": 466,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210B is the 50 mm bore member of NTN's medium-duty 7200 single-row family, with a 90 mm outside diameter and 20 mm section width. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 10 encodes the 50 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). With C 41.5 kN and C0 28.6 kN, each mm of bore carries about 0.83 kN of dynamic rating. Size selection is usually finished by checking that the C0 of 28.6 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Heat-mounting to 80-90 deg C is the clean route onto a 50 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A 7210B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "On a 50 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 41.5/28.6 kN ratings and 2.16 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7210B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7210B?",
        "a": "7210B is a single-row angular contact ball bearing to ISO 15: 50 mm bore, 90 mm outside diameter, 20 mm width (1.969 x 3.543 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 41.5 kN, C0 28.6 kN and a 2.16 kN fatigue load limit Pu; the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min; mass about 466 g."
      },
      {
        "q": "How is the 7210B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 10 encodes the 50 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 90 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7210B support?",
        "a": "One 7210B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7210B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7210B?",
        "a": "The 50/90/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 41.5 kN / C0 28.6 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210b",
      "7210B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ210",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ210",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 57.5,
    "static_load_kN": 89,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.8,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "speed_oil_rpm": 7500,
    "weight_g": 603,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty QJ200 four-point family, QJ210 measures 50 mm across the bore, 90 mm over the outer ring and 20 mm across the faces. Decoding QJ210: QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), with the last two digits 10 give the bore by the standard code table (50 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. On speed, the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 50 mm bore give the working limits. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,600 r/min with preload; check the grease speed factor against the catalogue figure.",
      "On a 50 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The C0 of 89 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 57.5/89 kN ratings and 3.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ210; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ210?",
        "a": "QJ210 is a four-point contact ball bearing to ISO 15: 50 mm bore, 90 mm outside diameter, 20 mm width (1.969 x 3.543 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 57.5 kN, C0 89 kN and a 3.8 kN fatigue load limit Pu; the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min; mass about 603 g."
      },
      {
        "q": "How is the QJ210 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 10 give the bore by the standard code table (50 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 90 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ210 support?",
        "a": "QJ210 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ210?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,600 r/min and the oil rating 7,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ210?",
        "a": "The 50/90/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 57.5 kN / C0 89 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ210",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj210",
      "QJ210"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5310S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5310S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 81.5,
    "static_load_kN": 61.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.8,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "speed_oil_rpm": 5600,
    "weight_g": 1840,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 5300S double-row family, 5310S measures 50 mm across the bore, 110 mm over the outer ring and 44.4 mm across the faces. Reading the code: 53 is the double-row dimension series (heavy-duty 5300S double-row family), 10 encodes the 50 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. NTN prints 81.5 kN dynamic and 61.5 kN static for this size and a 3.8 kN fatigue load limit Pu. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The 4,300 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 5310S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5310S without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 81.5/61.5 kN ratings and 3.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5310S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5310S?",
        "a": "5310S is a double-row angular contact ball bearing to ISO 15: 50 mm bore, 110 mm outside diameter, 44.4 mm width (1.969 x 4.331 x 1.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 81.5 kN, C0 61.5 kN and a 3.8 kN fatigue load limit Pu; the grease limiting speed is 4,300 r/min and the oil rating 5,600 r/min; mass about 1840 g."
      },
      {
        "q": "How is the 5310S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 10 encodes the 50 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 110 mm OD and 44.4 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5310S support?",
        "a": "5310S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5310S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,300 r/min and the oil rating 5,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5310S?",
        "a": "The 50/110/44.4 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 81.5 kN / C0 61.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5310S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5310s",
      "5310S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7310",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 82.5,
    "static_load_kN": 52.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.1,
    "limiting_speed_rpm": 7100,
    "max_rpm": 7100,
    "speed_oil_rpm": 9400,
    "weight_g": 1090,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 50 x 110 x 27 mm, NTN 7310 sits in the heavy-duty 7300 single-row family of the angular-contact programme. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 9,400 r/min sits 2,300 r/min above the 7,100 r/min grease figure — a 1.32x step that says how much headroom oil cooling buys. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 7,100 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 7,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 7310 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 7,100 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 82.5/52.5 kN ratings and 4.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7310; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7310?",
        "a": "7310 is a single-row angular contact ball bearing to ISO 15: 50 mm bore, 110 mm outside diameter, 27 mm width (1.969 x 4.331 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 82.5 kN, C0 52.5 kN and a 4.1 kN fatigue load limit Pu; the grease limiting speed is 7,100 r/min and the oil rating 9,400 r/min; mass about 1090 g."
      },
      {
        "q": "How is the 7310 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 10 encodes the 50 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 110 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7310 support?",
        "a": "One 7310 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7310?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,100 r/min and the oil rating 9,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7310?",
        "a": "The 50/110/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 82.5 kN / C0 52.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310",
      "7310-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7310B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 75.5,
    "static_load_kN": 48.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.8,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "speed_oil_rpm": 8100,
    "weight_g": 1110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7310B carries a 50 mm bore in a 110 mm outside diameter, 27 mm wide envelope. Decoding 7310B: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 10 encodes the 50 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The oil rating of 8,100 r/min sits 2,100 r/min above the 6,000 r/min grease figure — a 1.35x step that says how much headroom oil cooling buys. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. A 50 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Do not pair two random 7310B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 75.5/48.5 kN ratings and 3.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7310B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7310B?",
        "a": "7310B is a single-row angular contact ball bearing to ISO 15: 50 mm bore, 110 mm outside diameter, 27 mm width (1.969 x 4.331 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 75.5 kN, C0 48.5 kN and a 3.8 kN fatigue load limit Pu; the grease limiting speed is 6,000 r/min and the oil rating 8,100 r/min; mass about 1110 g."
      },
      {
        "q": "How is the 7310B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 10 encodes the 50 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 110 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7310B support?",
        "a": "One 7310B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7310B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,000 r/min and the oil rating 8,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7310B?",
        "a": "The 50/110/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 75.5 kN / C0 48.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310b",
      "7310B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ310",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ310",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 102,
    "static_load_kN": 145,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 6.2,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "speed_oil_rpm": 6700,
    "weight_g": 1380,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, QJ310 appears as a heavy-duty QJ300 four-point family bearing of 50 mm bore, 110 mm outside diameter and 27 mm width. Two fields make up the code — QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family) and the last two digits 10 give the bore by the standard code table (50 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The oil rating of 6,700 r/min sits 1,700 r/min above the 5,000 r/min grease figure — a 1.34x step that says how much headroom oil cooling buys. The 50/110/27 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 50 mm bore give the working limits. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 50 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ310 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 102/145 kN ratings and 6.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ310; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ310?",
        "a": "QJ310 is a four-point contact ball bearing to ISO 15: 50 mm bore, 110 mm outside diameter, 27 mm width (1.969 x 4.331 x 1.063 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 102 kN, C0 145 kN and a 6.2 kN fatigue load limit Pu; the grease limiting speed is 5,000 r/min and the oil rating 6,700 r/min; mass about 1380 g."
      },
      {
        "q": "How is the QJ310 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 10 give the bore by the standard code table (50 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 110 mm OD and 27 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ310 support?",
        "a": "QJ310 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ310?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,000 r/min and the oil rating 6,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ310?",
        "a": "The 50/110/27 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 102 kN / C0 145 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ310",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj310",
      "QJ310"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7911",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7911",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 80,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 19.2,
    "static_load_kN": 16.1,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 1.07,
    "limiting_speed_rpm": 8400,
    "max_rpm": 8400,
    "speed_oil_rpm": 11000,
    "weight_g": 214,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The extra-light, high-speed 7900 single-row family entry 7911 carries a 55 mm bore in a 80 mm outside diameter, 13 mm wide envelope. NTN builds the number from 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), then 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 214 g, which at this 12.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. A 55 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 16.1 kN really covers the worst static case before substituting it for a 7000.",
      "On a 55 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 19.2/16.1 kN ratings and 1.07 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7911; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7911?",
        "a": "7911 is a single-row angular contact ball bearing to ISO 15: 55 mm bore, 80 mm outside diameter, 13 mm width (2.165 x 3.15 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 19.2 kN, C0 16.1 kN and a 1.07 kN fatigue load limit Pu; the grease limiting speed is 8,400 r/min and the oil rating 11,000 r/min; mass about 214 g."
      },
      {
        "q": "How is the 7911 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 80 mm OD and 13 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7911 support?",
        "a": "One 7911 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7911?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 8,400 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7911?",
        "a": "The 55/80/13 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 19.2 kN / C0 16.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7911",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7911"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7011-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7011",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 90,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 34.5,
    "static_load_kN": 26.3,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.9,
    "limiting_speed_rpm": 7900,
    "max_rpm": 7900,
    "speed_oil_rpm": 11000,
    "weight_g": 447,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 55 x 90 x 18 mm, NTN 7011 sits in the standard-section 7000 single-row family of the angular-contact programme. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 17.5 mm of radial section, the catalogue still quotes 34.5 kN dynamic capacity for the 55 mm bore. The 55/90/18 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7011 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 34.5/26.3 kN ratings and 1.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7011; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7011?",
        "a": "7011 is a single-row angular contact ball bearing to ISO 15: 55 mm bore, 90 mm outside diameter, 18 mm width (2.165 x 3.543 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 34.5 kN, C0 26.3 kN and a 1.9 kN fatigue load limit Pu; the grease limiting speed is 7,900 r/min and the oil rating 11,000 r/min; mass about 447 g."
      },
      {
        "q": "How is the 7011 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 90 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7011 support?",
        "a": "One 7011 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7011?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,900 r/min and the oil rating 11,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7011?",
        "a": "The 55/90/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 34.5 kN / C0 26.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7011",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7011",
      "7011-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5211S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5211S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 33.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 56,
    "static_load_kN": 49,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "speed_oil_rpm": 5600,
    "weight_g": 1010,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 55 x 100 x 33.3 mm, NTN 5211S sits in the medium-duty 5200S double-row family of the angular-contact programme. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 11 encodes the 55 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. NTN prints 56 kN dynamic and 49 kN static for this size and a 3 kN fatigue load limit Pu. For a 55 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Heat-mounting to 80-90 deg C is the clean route onto a 55 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 5211S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5211S without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 56/49 kN ratings and 3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5211S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5211S?",
        "a": "5211S is a double-row angular contact ball bearing to ISO 15: 55 mm bore, 100 mm outside diameter, 33.3 mm width (2.165 x 3.937 x 1.311 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 56 kN, C0 49 kN and a 3 kN fatigue load limit Pu; the grease limiting speed is 4,300 r/min and the oil rating 5,600 r/min; mass about 1010 g."
      },
      {
        "q": "How is the 5211S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 11 encodes the 55 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 100 mm OD and 33.3 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5211S support?",
        "a": "5211S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5211S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,300 r/min and the oil rating 5,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5211S?",
        "a": "The 55/100/33.3 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 56 kN / C0 49 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5211S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5211s",
      "5211S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7211",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 56.5,
    "static_load_kN": 39.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.1,
    "limiting_speed_rpm": 7100,
    "max_rpm": 7100,
    "speed_oil_rpm": 9500,
    "weight_g": 600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 55 x 100 x 21 mm, NTN 7211 sits in the medium-duty 7200 single-row family of the angular-contact programme. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 56.5 kN dynamic and 39.5 kN static for this size and a 3.1 kN fatigue load limit Pu. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Grease quantity matters as much as grade at 7,100 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7211 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 39.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7211 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 56.5/39.5 kN ratings and 3.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7211; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7211?",
        "a": "7211 is a single-row angular contact ball bearing to ISO 15: 55 mm bore, 100 mm outside diameter, 21 mm width (2.165 x 3.937 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 56.5 kN, C0 39.5 kN and a 3.1 kN fatigue load limit Pu; the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min; mass about 600 g."
      },
      {
        "q": "How is the 7211 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 100 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7211 support?",
        "a": "One 7211 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7211?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,100 r/min and the oil rating 9,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7211?",
        "a": "The 55/100/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 56.5 kN / C0 39.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211",
      "7211-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7211B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 51.5,
    "static_load_kN": 36,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.74,
    "limiting_speed_rpm": 6100,
    "max_rpm": 6100,
    "speed_oil_rpm": 8200,
    "weight_g": 612,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7211B appears as a medium-duty 7200 single-row family bearing of 55 mm bore, 100 mm outside diameter and 21 mm width. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 11 encodes the 55 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The oil rating of 8,200 r/min sits 2,100 r/min above the 6,100 r/min grease figure — a 1.34x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 55 mm bore give the working limits. ",
    "applications": [
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,100 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random 7211B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,100 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 51.5/36 kN ratings and 2.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7211B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7211B?",
        "a": "7211B is a single-row angular contact ball bearing to ISO 15: 55 mm bore, 100 mm outside diameter, 21 mm width (2.165 x 3.937 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 51.5 kN, C0 36 kN and a 2.74 kN fatigue load limit Pu; the grease limiting speed is 6,100 r/min and the oil rating 8,200 r/min; mass about 612 g."
      },
      {
        "q": "How is the 7211B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 11 encodes the 55 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 100 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7211B support?",
        "a": "One 7211B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7211B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,100 r/min and the oil rating 8,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7211B?",
        "a": "The 55/100/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 51.5 kN / C0 36 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211b",
      "7211B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ211",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ211",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 71,
    "static_load_kN": 112,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 4.8,
    "limiting_speed_rpm": 5100,
    "max_rpm": 5100,
    "speed_oil_rpm": 6800,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ211 is an NTN four-point contact ball bearing: medium-duty QJ200 four-point family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 55 x 100 x 21 mm. NTN builds the number from QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), then the last two digits 11 give the bore by the standard code table (55 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. With C 71 kN and C0 112 kN, each mm of bore carries about 1.29 kN of dynamic rating. Choose the medium-duty QJ200 four-point family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Heat-mounting to 80-90 deg C is the clean route onto a 55 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 55 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 71/112 kN ratings and 4.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ211; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ211?",
        "a": "QJ211 is a four-point contact ball bearing to ISO 15: 55 mm bore, 100 mm outside diameter, 21 mm width (2.165 x 3.937 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 71 kN, C0 112 kN and a 4.8 kN fatigue load limit Pu; the grease limiting speed is 5,100 r/min and the oil rating 6,800 r/min; mass about 780 g."
      },
      {
        "q": "How is the QJ211 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 11 give the bore by the standard code table (55 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 100 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ211 support?",
        "a": "QJ211 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ211?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,100 r/min and the oil rating 6,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ211?",
        "a": "The 55/100/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 71 kN / C0 112 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ211",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj211",
      "QJ211"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5311S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5311S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 95,
    "static_load_kN": 73,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.5,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "speed_oil_rpm": 5000,
    "weight_g": 2400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5311S belongs to the heavy-duty 5300S double-row family: the catalogue boundary dimensions read 55 / 120 / 49.2 mm (bore / OD / width). Decoding 5311S: 53 is the double-row dimension series (heavy-duty 5300S double-row family), with 11 encodes the 55 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Catalogue mass is about 2400 g, which at this 32.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. A 55 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 95/73 kN ratings and 4.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5311S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5311S?",
        "a": "5311S is a double-row angular contact ball bearing to ISO 15: 55 mm bore, 120 mm outside diameter, 49.2 mm width (2.165 x 4.724 x 1.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 95 kN, C0 73 kN and a 4.5 kN fatigue load limit Pu; the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min; mass about 2400 g."
      },
      {
        "q": "How is the 5311S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 11 encodes the 55 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 120 mm OD and 49.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5311S support?",
        "a": "5311S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5311S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5311S?",
        "a": "The 55/120/49.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 95 kN / C0 73 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5311S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5311s",
      "5311S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7311",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 95,
    "static_load_kN": 61.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.8,
    "limiting_speed_rpm": 6400,
    "max_rpm": 6400,
    "speed_oil_rpm": 8600,
    "weight_g": 1390,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 is the 55 mm bore member of NTN's heavy-duty 7300 single-row family, with a 120 mm outside diameter and 29 mm section width. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 95 kN against C0 61.5 kN — a C0/C ratio of 0.65 that is typical of an angular-contact contact ellipse. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 6,400 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling",
      "industrial pump and blower impeller shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 95/61.5 kN ratings and 4.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7311; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7311?",
        "a": "7311 is a single-row angular contact ball bearing to ISO 15: 55 mm bore, 120 mm outside diameter, 29 mm width (2.165 x 4.724 x 1.142 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 95 kN, C0 61.5 kN and a 4.8 kN fatigue load limit Pu; the grease limiting speed is 6,400 r/min and the oil rating 8,600 r/min; mass about 1390 g."
      },
      {
        "q": "How is the 7311 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 11 encodes the 55 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 120 mm OD and 29 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7311 support?",
        "a": "One 7311 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7311?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,400 r/min and the oil rating 8,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7311?",
        "a": "The 55/120/29 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 95 kN / C0 61.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311",
      "7311-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7311B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 87,
    "static_load_kN": 56.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.45,
    "limiting_speed_rpm": 5500,
    "max_rpm": 5500,
    "speed_oil_rpm": 7300,
    "weight_g": 1420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7311B measures 55 mm across the bore, 120 mm over the outer ring and 29 mm across the faces. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 11 encodes the 55 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). At roughly 32.5 mm of radial section, the catalogue still quotes 87 kN dynamic capacity for the 55 mm bore. Against a deep-groove bearing of the same 55 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "industrial pump and blower impeller shafts",
      "gearbox input shafts under helical-gear thrust",
      "electric motor shafts with axial locating duty",
      "conveyor drive and tension-drum shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 56.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 87/56.5 kN ratings and 4.45 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7311B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7311B?",
        "a": "7311B is a single-row angular contact ball bearing to ISO 15: 55 mm bore, 120 mm outside diameter, 29 mm width (2.165 x 4.724 x 1.142 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 87 kN, C0 56.5 kN and a 4.45 kN fatigue load limit Pu; the grease limiting speed is 5,500 r/min and the oil rating 7,300 r/min; mass about 1420 g."
      },
      {
        "q": "How is the 7311B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 11 encodes the 55 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 120 mm OD and 29 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7311B support?",
        "a": "One 7311B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7311B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,500 r/min and the oil rating 7,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7311B?",
        "a": "The 55/120/29 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 87 kN / C0 56.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=129",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311b",
      "7311B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ311",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ311",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 118,
    "static_load_kN": 170,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 7.3,
    "limiting_speed_rpm": 4600,
    "max_rpm": 4600,
    "speed_oil_rpm": 6100,
    "weight_g": 1760,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN QJ311 belongs to the heavy-duty QJ300 four-point family: the catalogue boundary dimensions read 55 / 120 / 29 mm (bore / OD / width). Decoding QJ311: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), with the last two digits 11 give the bore by the standard code table (55 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Catalogue dynamic rating C is 118 kN against C0 170 kN — a C0/C ratio of 1.44 that is typical of an angular-contact contact ellipse. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Heat-mounting to 80-90 deg C is the clean route onto a 55 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "conveyor drive and tension-drum shafts",
      "agricultural gearbox and PTO shaft supports",
      "printing-press cylinder and folder shafts",
      "machine-tool spindle cartridges and driven tooling"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "In this size class the common miss is lubrication interval, not fit — a 55 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "The C0 of 170 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ311 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 118/170 kN ratings and 7.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ311; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ311?",
        "a": "QJ311 is a four-point contact ball bearing to ISO 15: 55 mm bore, 120 mm outside diameter, 29 mm width (2.165 x 4.724 x 1.142 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 118 kN, C0 170 kN and a 7.3 kN fatigue load limit Pu; the grease limiting speed is 4,600 r/min and the oil rating 6,100 r/min; mass about 1760 g."
      },
      {
        "q": "How is the QJ311 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 11 give the bore by the standard code table (55 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 120 mm OD and 29 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ311 support?",
        "a": "QJ311 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ311?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,600 r/min and the oil rating 6,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ311?",
        "a": "The 55/120/29 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 118 kN / C0 170 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ311",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj311",
      "QJ311"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7912",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7912",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 85,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 20,
    "static_load_kN": 17.4,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 1.16,
    "limiting_speed_rpm": 7800,
    "max_rpm": 7800,
    "speed_oil_rpm": 10000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 60 x 85 x 13 mm, NTN 7912 sits in the extra-light, high-speed 7900 single-row family of the angular-contact programme. The designation breaks down as 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 12.5 mm, and the catalogue couples that with C 20 kN / C0 17.4 kN. For a 60 mm shaft with combined load, the practical shortlist is this series, its 7000-series standard section, and — where thrust reverses — a back-to-back pair rather than a single row. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 17.4 kN really covers the worst static case before substituting it for a 7000.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7912 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 20/17.4 kN ratings and 1.16 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7912; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7912?",
        "a": "7912 is a single-row angular contact ball bearing to ISO 15: 60 mm bore, 85 mm outside diameter, 13 mm width (2.362 x 3.346 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 20 kN, C0 17.4 kN and a 1.16 kN fatigue load limit Pu; the grease limiting speed is 7,800 r/min and the oil rating 10,000 r/min; mass about 230 g."
      },
      {
        "q": "How is the 7912 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 85 mm OD and 13 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7912 support?",
        "a": "One 7912 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7912?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,800 r/min and the oil rating 10,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7912?",
        "a": "The 60/85/13 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 20 kN / C0 17.4 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7912",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7912"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7012-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7012",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 95,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 28.1,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 1.99,
    "limiting_speed_rpm": 7200,
    "max_rpm": 7200,
    "speed_oil_rpm": 9600,
    "weight_g": 478,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7012 carries a 60 mm bore in a 95 mm outside diameter, 18 mm wide envelope. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Size selection is usually finished by checking that the C0 of 28.1 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 7,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 7,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 35.5/28.1 kN ratings and 1.99 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7012; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7012?",
        "a": "7012 is a single-row angular contact ball bearing to ISO 15: 60 mm bore, 95 mm outside diameter, 18 mm width (2.362 x 3.74 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 35.5 kN, C0 28.1 kN and a 1.99 kN fatigue load limit Pu; the grease limiting speed is 7,200 r/min and the oil rating 9,600 r/min; mass about 478 g."
      },
      {
        "q": "How is the 7012 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 95 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7012 support?",
        "a": "One 7012 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7012?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,200 r/min and the oil rating 9,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7012?",
        "a": "The 60/95/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 35.5 kN / C0 28.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7012",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7012",
      "7012-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5212S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5212S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 69,
    "static_load_kN": 62,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.8,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "speed_oil_rpm": 5000,
    "weight_g": 1330,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5212S is an NTN double-row angular contact ball bearing: medium-duty 5200S double-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 60 x 110 x 36.5 mm. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 12 encodes the 60 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Catalogue mass is about 1330 g, which at this 25.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 60 mm bore give the working limits. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5212S without re-checking axial float, heat and housing width — the kinematics differ.",
      "Do not pair two random 5212S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 69/62 kN ratings and 3.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5212S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5212S?",
        "a": "5212S is a double-row angular contact ball bearing to ISO 15: 60 mm bore, 110 mm outside diameter, 36.5 mm width (2.362 x 4.331 x 1.437 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 69 kN, C0 62 kN and a 3.8 kN fatigue load limit Pu; the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min; mass about 1330 g."
      },
      {
        "q": "How is the 5212S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 12 encodes the 60 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 110 mm OD and 36.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5212S support?",
        "a": "5212S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5212S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5212S?",
        "a": "The 60/110/36.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 69 kN / C0 62 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5212S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5212s",
      "5212S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7212",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 68.5,
    "static_load_kN": 49,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.85,
    "limiting_speed_rpm": 6600,
    "max_rpm": 6600,
    "speed_oil_rpm": 8800,
    "weight_g": 765,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 is the 60 mm bore member of NTN's medium-duty 7200 single-row family, with a 110 mm outside diameter and 22 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Against a deep-groove bearing of the same 60 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 6,600 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7212 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 6,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 68.5/49 kN ratings and 3.85 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7212; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7212?",
        "a": "7212 is a single-row angular contact ball bearing to ISO 15: 60 mm bore, 110 mm outside diameter, 22 mm width (2.362 x 4.331 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 68.5 kN, C0 49 kN and a 3.85 kN fatigue load limit Pu; the grease limiting speed is 6,600 r/min and the oil rating 8,800 r/min; mass about 765 g."
      },
      {
        "q": "How is the 7212 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 110 mm OD and 22 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7212 support?",
        "a": "One 7212 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7212?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,600 r/min and the oil rating 8,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7212?",
        "a": "The 60/110/22 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 68.5 kN / C0 49 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212",
      "7212-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7212B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 62,
    "static_load_kN": 44.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.4,
    "limiting_speed_rpm": 5700,
    "max_rpm": 5700,
    "speed_oil_rpm": 7600,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 60 x 110 x 22 mm, NTN 7212B sits in the medium-duty 7200 single-row family of the angular-contact programme. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 12 encodes the 60 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). At roughly 25.0 mm of radial section, the catalogue still quotes 62 kN dynamic capacity for the 60 mm bore. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "On a 60 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 62/44.5 kN ratings and 3.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7212B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7212B?",
        "a": "7212B is a single-row angular contact ball bearing to ISO 15: 60 mm bore, 110 mm outside diameter, 22 mm width (2.362 x 4.331 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 62 kN, C0 44.5 kN and a 3.4 kN fatigue load limit Pu; the grease limiting speed is 5,700 r/min and the oil rating 7,600 r/min; mass about 780 g."
      },
      {
        "q": "How is the 7212B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 12 encodes the 60 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 110 mm OD and 22 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7212B support?",
        "a": "One 7212B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7212B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,700 r/min and the oil rating 7,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7212B?",
        "a": "The 60/110/22 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 62 kN / C0 44.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212b",
      "7212B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ212",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ212",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 86,
    "static_load_kN": 138,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 5.9,
    "limiting_speed_rpm": 4700,
    "max_rpm": 4700,
    "speed_oil_rpm": 6300,
    "weight_g": 980,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, QJ212 appears as a medium-duty QJ200 four-point family bearing of 60 mm bore, 110 mm outside diameter and 22 mm width. The designation breaks down as QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 12 give the bore by the standard code table (60 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The static margin, C0 138 kN versus C 86 kN, is what supports slow oscillating duty and shock without immediate brinelling. Size selection is usually finished by checking that the C0 of 138 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Do not pair two random QJ212 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ212 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Do not pair two random QJ212 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 86/138 kN ratings and 5.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ212; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ212?",
        "a": "QJ212 is a four-point contact ball bearing to ISO 15: 60 mm bore, 110 mm outside diameter, 22 mm width (2.362 x 4.331 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 86 kN, C0 138 kN and a 5.9 kN fatigue load limit Pu; the grease limiting speed is 4,700 r/min and the oil rating 6,300 r/min; mass about 980 g."
      },
      {
        "q": "How is the QJ212 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 12 give the bore by the standard code table (60 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 110 mm OD and 22 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ212 support?",
        "a": "QJ212 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ212?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,700 r/min and the oil rating 6,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ212?",
        "a": "The 60/110/22 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 86 kN / C0 138 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ212",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj212",
      "QJ212"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5312S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5312S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 54,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 125,
    "static_load_kN": 98.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4500,
    "weight_g": 2920,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5312S is the 60 mm bore member of NTN's heavy-duty 5300S double-row family, with a 130 mm outside diameter and 54 mm section width. The designation breaks down as 53 is the double-row dimension series (heavy-duty 5300S double-row family); 12 encodes the 60 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The built-in back-to-back contact lines give the double-row bearing its two-direction thrust and moment capacity from one ring set. The 60/130/54 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 5312S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 125/98.5 kN ratings and 6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5312S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5312S?",
        "a": "5312S is a double-row angular contact ball bearing to ISO 15: 60 mm bore, 130 mm outside diameter, 54 mm width (2.362 x 5.118 x 2.126 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 125 kN, C0 98.5 kN and a 6 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min; mass about 2920 g."
      },
      {
        "q": "How is the 5312S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 12 encodes the 60 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 130 mm OD and 54 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5312S support?",
        "a": "5312S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5312S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5312S?",
        "a": "The 60/130/54 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 125 kN / C0 98.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5312S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5312s",
      "5312S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7312",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 109,
    "static_load_kN": 71.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.6,
    "limiting_speed_rpm": 5900,
    "max_rpm": 5900,
    "speed_oil_rpm": 7900,
    "weight_g": 1740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 60 x 130 x 31 mm, NTN 7312 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Decoding 7312: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 109 kN dynamic and 71.5 kN static for this size and a 5.6 kN fatigue load limit Pu. For a 60 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. A 60 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7312 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7312 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7312 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 109/71.5 kN ratings and 5.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7312; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7312?",
        "a": "7312 is a single-row angular contact ball bearing to ISO 15: 60 mm bore, 130 mm outside diameter, 31 mm width (2.362 x 5.118 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 109 kN, C0 71.5 kN and a 5.6 kN fatigue load limit Pu; the grease limiting speed is 5,900 r/min and the oil rating 7,900 r/min; mass about 1740 g."
      },
      {
        "q": "How is the 7312 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 12 encodes the 60 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 130 mm OD and 31 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7312 support?",
        "a": "One 7312 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7312?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,900 r/min and the oil rating 7,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7312?",
        "a": "The 60/130/31 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 109 kN / C0 71.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312",
      "7312-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7312B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 99.5,
    "static_load_kN": 66,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.15,
    "limiting_speed_rpm": 5100,
    "max_rpm": 5100,
    "speed_oil_rpm": 6800,
    "weight_g": 1770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7312B belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 60 / 130 / 31 mm (bore / OD / width). Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 12 encodes the 60 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Grease quantity matters as much as grade at 5,100 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The C0 of 66 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 5,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 99.5/66 kN ratings and 5.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7312B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7312B?",
        "a": "7312B is a single-row angular contact ball bearing to ISO 15: 60 mm bore, 130 mm outside diameter, 31 mm width (2.362 x 5.118 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 99.5 kN, C0 66 kN and a 5.15 kN fatigue load limit Pu; the grease limiting speed is 5,100 r/min and the oil rating 6,800 r/min; mass about 1770 g."
      },
      {
        "q": "How is the 7312B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 12 encodes the 60 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 130 mm OD and 31 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7312B support?",
        "a": "One 7312B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7312B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,100 r/min and the oil rating 6,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7312B?",
        "a": "The 60/130/31 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 99.5 kN / C0 66 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312b",
      "7312B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ312",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ312",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 135,
    "static_load_kN": 198,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 8.5,
    "limiting_speed_rpm": 4200,
    "max_rpm": 4200,
    "speed_oil_rpm": 5700,
    "weight_g": 2180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty QJ300 four-point family entry QJ312 carries a 60 mm bore in a 130 mm outside diameter, 31 mm wide envelope. NTN builds the number from QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), then the last two digits 12 give the bore by the standard code table (60 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. At roughly 35.0 mm of radial section, the catalogue still quotes 135 kN dynamic capacity for the 60 mm bore. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 60 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,200 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 135/198 kN ratings and 8.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ312; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ312?",
        "a": "QJ312 is a four-point contact ball bearing to ISO 15: 60 mm bore, 130 mm outside diameter, 31 mm width (2.362 x 5.118 x 1.22 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 135 kN, C0 198 kN and a 8.5 kN fatigue load limit Pu; the grease limiting speed is 4,200 r/min and the oil rating 5,700 r/min; mass about 2180 g."
      },
      {
        "q": "How is the QJ312 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 12 give the bore by the standard code table (60 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 130 mm OD and 31 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ312 support?",
        "a": "QJ312 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ312?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,200 r/min and the oil rating 5,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ312?",
        "a": "The 60/130/31 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 135 kN / C0 198 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ312",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj312",
      "QJ312"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7913",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7913",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 90,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 20.2,
    "static_load_kN": 18,
    "cage_type": "polymer_PA66",
    "fatigue_load_limit_kN": 1.2,
    "limiting_speed_rpm": 7200,
    "max_rpm": 7200,
    "speed_oil_rpm": 9600,
    "weight_g": 245,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7913 is the 65 mm bore member of NTN's extra-light, high-speed 7900 single-row family, with a 90 mm outside diameter and 13 mm section width. Reading the code: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 18 kN static rating into useful one-direction thrust capacity. Against a deep-groove bearing of the same 65 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 65 mm bore give the working limits. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 18 kN really covers the worst static case before substituting it for a 7000.",
      "The C0 of 18 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Do not pair two random 7913 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A 7913 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 20.2/18 kN ratings and 1.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7913; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7913?",
        "a": "7913 is a single-row angular contact ball bearing to ISO 15: 65 mm bore, 90 mm outside diameter, 13 mm width (2.559 x 3.543 x 0.512 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 20.2 kN, C0 18 kN and a 1.2 kN fatigue load limit Pu; the grease limiting speed is 7,200 r/min and the oil rating 9,600 r/min; mass about 245 g."
      },
      {
        "q": "How is the 7913 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 90 mm OD and 13 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7913 support?",
        "a": "One 7913 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7913?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 7,200 r/min and the oil rating 9,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7913?",
        "a": "The 65/90/13 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 20.2 kN / C0 18 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7913",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7913"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7013-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7013",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 100,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 37.5,
    "static_load_kN": 31.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.18,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "speed_oil_rpm": 9000,
    "weight_g": 509,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 65 x 100 x 18 mm, NTN 7013 sits in the standard-section 7000 single-row family of the angular-contact programme. Decoding 7013: 70 is the single-row dimension series (standard-section 7000 single-row family), with 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 509 g, which at this 17.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. The 65/100/18 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 37.5/31.5 kN ratings and 2.18 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7013; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7013?",
        "a": "7013 is a single-row angular contact ball bearing to ISO 15: 65 mm bore, 100 mm outside diameter, 18 mm width (2.559 x 3.937 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 37.5 kN, C0 31.5 kN and a 2.18 kN fatigue load limit Pu; the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min; mass about 509 g."
      },
      {
        "q": "How is the 7013 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 100 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7013 support?",
        "a": "One 7013 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7013?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7013?",
        "a": "The 65/100/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 37.5 kN / C0 31.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7013",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7013",
      "7013-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5213S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5213S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 38.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 76.5,
    "static_load_kN": 69,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.2,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "speed_oil_rpm": 4500,
    "weight_g": 1710,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 5200S double-row family entry 5213S carries a 65 mm bore in a 120 mm outside diameter, 38.1 mm wide envelope. NTN builds the number from 52 is the double-row dimension series (medium-duty 5200S double-row family), then 13 encodes the 65 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The built-in back-to-back contact lines give the double-row bearing its two-direction thrust and moment capacity from one ring set. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A 5213S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 76.5/69 kN ratings and 4.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5213S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5213S?",
        "a": "5213S is a double-row angular contact ball bearing to ISO 15: 65 mm bore, 120 mm outside diameter, 38.1 mm width (2.559 x 4.724 x 1.5 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 76.5 kN, C0 69 kN and a 4.2 kN fatigue load limit Pu; the grease limiting speed is 3,600 r/min and the oil rating 4,500 r/min; mass about 1710 g."
      },
      {
        "q": "How is the 5213S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 13 encodes the 65 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 120 mm OD and 38.1 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5213S support?",
        "a": "5213S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5213S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,600 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5213S?",
        "a": "The 65/120/38.1 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 76.5 kN / C0 69 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5213S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5213s",
      "5213S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7213",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 78,
    "static_load_kN": 58,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.55,
    "limiting_speed_rpm": 6100,
    "max_rpm": 6100,
    "speed_oil_rpm": 8100,
    "weight_g": 962,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 65 x 120 x 23 mm, NTN 7213 sits in the medium-duty 7200 single-row family of the angular-contact programme. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 27.5 mm, and the catalogue couples that with C 78 kN / C0 58 kN. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. A 65 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Do not pair two random 7213 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 6,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 78/58 kN ratings and 4.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7213; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7213?",
        "a": "7213 is a single-row angular contact ball bearing to ISO 15: 65 mm bore, 120 mm outside diameter, 23 mm width (2.559 x 4.724 x 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 78 kN, C0 58 kN and a 4.55 kN fatigue load limit Pu; the grease limiting speed is 6,100 r/min and the oil rating 8,100 r/min; mass about 962 g."
      },
      {
        "q": "How is the 7213 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 120 mm OD and 23 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7213 support?",
        "a": "One 7213 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7213?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,100 r/min and the oil rating 8,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7213?",
        "a": "The 65/120/23 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 78 kN / C0 58 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213",
      "7213-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7213B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 70.5,
    "static_load_kN": 52.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.95,
    "limiting_speed_rpm": 5200,
    "max_rpm": 5200,
    "speed_oil_rpm": 7000,
    "weight_g": 981,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213B is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 65 x 120 x 23 mm. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 13 encodes the 65 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Against a deep-groove bearing of the same 65 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 65 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A 7213B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 5,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 70.5/52.5 kN ratings and 3.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7213B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7213B?",
        "a": "7213B is a single-row angular contact ball bearing to ISO 15: 65 mm bore, 120 mm outside diameter, 23 mm width (2.559 x 4.724 x 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 70.5 kN, C0 52.5 kN and a 3.95 kN fatigue load limit Pu; the grease limiting speed is 5,200 r/min and the oil rating 7,000 r/min; mass about 981 g."
      },
      {
        "q": "How is the 7213B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 13 encodes the 65 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 120 mm OD and 23 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7213B support?",
        "a": "One 7213B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7213B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,200 r/min and the oil rating 7,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7213B?",
        "a": "The 65/120/23 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 70.5 kN / C0 52.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213b",
      "7213B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ213",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ213",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 93.5,
    "static_load_kN": 153,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 6.55,
    "limiting_speed_rpm": 4400,
    "max_rpm": 4400,
    "speed_oil_rpm": 5800,
    "weight_g": 1240,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN QJ213 belongs to the medium-duty QJ200 four-point family: the catalogue boundary dimensions read 65 / 120 / 23 mm (bore / OD / width). Reading the code: QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), the last two digits 13 give the bore by the standard code table (65 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The oil rating of 5,800 r/min sits 1,400 r/min above the 4,400 r/min grease figure — a 1.32x step that says how much headroom oil cooling buys. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Grease quantity matters as much as grade at 4,400 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "The 4,400 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 93.5/153 kN ratings and 6.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ213; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ213?",
        "a": "QJ213 is a four-point contact ball bearing to ISO 15: 65 mm bore, 120 mm outside diameter, 23 mm width (2.559 x 4.724 x 0.906 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 93.5 kN, C0 153 kN and a 6.55 kN fatigue load limit Pu; the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min; mass about 1240 g."
      },
      {
        "q": "How is the QJ213 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 13 give the bore by the standard code table (65 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 120 mm OD and 23 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ213 support?",
        "a": "QJ213 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ213?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ213?",
        "a": "The 65/120/23 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 93.5 kN / C0 153 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ213",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj213",
      "QJ213"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5313S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5313S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 58.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 142,
    "static_load_kN": 113,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4300,
    "weight_g": 3670,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5313S appears as a heavy-duty 5300S double-row family bearing of 65 mm bore, 140 mm outside diameter and 58.7 mm width. Two fields make up the code — 53 is the double-row dimension series (heavy-duty 5300S double-row family) and 13 encodes the 65 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. With C 142 kN and C0 113 kN, each mm of bore carries about 2.18 kN of dynamic rating. Size selection is usually finished by checking that the C0 of 113 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Grease quantity matters as much as grade at 3,200 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "On a 65 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The C0 of 113 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "On a 65 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 142/113 kN ratings and 7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5313S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5313S?",
        "a": "5313S is a double-row angular contact ball bearing to ISO 15: 65 mm bore, 140 mm outside diameter, 58.7 mm width (2.559 x 5.512 x 2.311 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 142 kN, C0 113 kN and a 7 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min; mass about 3670 g."
      },
      {
        "q": "How is the 5313S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 13 encodes the 65 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 140 mm OD and 58.7 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5313S support?",
        "a": "5313S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5313S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5313S?",
        "a": "The 65/140/58.7 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 142 kN / C0 113 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5313S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5313s",
      "5313S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7313",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 123,
    "static_load_kN": 82,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6.35,
    "limiting_speed_rpm": 5500,
    "max_rpm": 5500,
    "speed_oil_rpm": 7300,
    "weight_g": 2110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 is the 65 mm bore member of NTN's heavy-duty 7300 single-row family, with a 140 mm outside diameter and 33 mm section width. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 65 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7313 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 5,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 123/82 kN ratings and 6.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7313; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7313?",
        "a": "7313 is a single-row angular contact ball bearing to ISO 15: 65 mm bore, 140 mm outside diameter, 33 mm width (2.559 x 5.512 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 123 kN, C0 82 kN and a 6.35 kN fatigue load limit Pu; the grease limiting speed is 5,500 r/min and the oil rating 7,300 r/min; mass about 2110 g."
      },
      {
        "q": "How is the 7313 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 13 encodes the 65 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 140 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7313 support?",
        "a": "One 7313 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7313?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,500 r/min and the oil rating 7,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7313?",
        "a": "The 65/140/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 123 kN / C0 82 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313",
      "7313-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7313B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 113,
    "static_load_kN": 75.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.85,
    "limiting_speed_rpm": 4700,
    "max_rpm": 4700,
    "speed_oil_rpm": 6300,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313B is the 65 mm bore member of NTN's heavy-duty 7300 single-row family, with a 140 mm outside diameter and 33 mm section width. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 13 encodes the 65 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The radial section height here is 37.5 mm, and the catalogue couples that with C 113 kN / C0 75.5 kN. For a 65 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The 4,700 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 113/75.5 kN ratings and 5.85 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7313B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7313B?",
        "a": "7313B is a single-row angular contact ball bearing to ISO 15: 65 mm bore, 140 mm outside diameter, 33 mm width (2.559 x 5.512 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 113 kN, C0 75.5 kN and a 5.85 kN fatigue load limit Pu; the grease limiting speed is 4,700 r/min and the oil rating 6,300 r/min; mass about 2150 g."
      },
      {
        "q": "How is the 7313B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 13 encodes the 65 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 140 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7313B support?",
        "a": "One 7313B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7313B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,700 r/min and the oil rating 6,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7313B?",
        "a": "The 65/140/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 113 kN / C0 75.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313b",
      "7313B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ313",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ313",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 153,
    "static_load_kN": 228,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 9.7,
    "limiting_speed_rpm": 3900,
    "max_rpm": 3900,
    "speed_oil_rpm": 5200,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 65 x 140 x 33 mm, NTN QJ313 sits in the heavy-duty QJ300 four-point family of the angular-contact programme. The designation breaks down as QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 13 give the bore by the standard code table (65 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. NTN prints 153 kN dynamic and 228 kN static for this size and a 9.7 kN fatigue load limit Pu. Choose the heavy-duty QJ300 four-point family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Grease quantity matters as much as grade at 3,900 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 65 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A QJ313 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 228 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ313 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 153/228 kN ratings and 9.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ313; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ313?",
        "a": "QJ313 is a four-point contact ball bearing to ISO 15: 65 mm bore, 140 mm outside diameter, 33 mm width (2.559 x 5.512 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 153 kN, C0 228 kN and a 9.7 kN fatigue load limit Pu; the grease limiting speed is 3,900 r/min and the oil rating 5,200 r/min; mass about 2700 g."
      },
      {
        "q": "How is the QJ313 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 13 give the bore by the standard code table (65 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 140 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ313 support?",
        "a": "QJ313 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ313?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,900 r/min and the oil rating 5,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ313?",
        "a": "The 65/140/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 153 kN / C0 228 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ313",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj313",
      "QJ313"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7914",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7914",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 100,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 29,
    "static_load_kN": 26.2,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 1.74,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "speed_oil_rpm": 9000,
    "weight_g": 397,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the extra-light, high-speed 7900 single-row family, 7914 measures 70 mm across the bore, 100 mm over the outer ring and 16 mm across the faces. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 70 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 26.2 kN really covers the worst static case before substituting it for a 7000.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A 7914 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 26.2 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 29/26.2 kN ratings and 1.74 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7914; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7914?",
        "a": "7914 is a single-row angular contact ball bearing to ISO 15: 70 mm bore, 100 mm outside diameter, 16 mm width (2.756 x 3.937 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 29 kN, C0 26.2 kN and a 1.74 kN fatigue load limit Pu; the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min; mass about 397 g."
      },
      {
        "q": "How is the 7914 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 100 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7914 support?",
        "a": "One 7914 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7914?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,700 r/min and the oil rating 9,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7914?",
        "a": "The 70/100/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 29 kN / C0 26.2 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7914",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7914"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7014-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7014",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 110,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 47.5,
    "static_load_kN": 39.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.78,
    "limiting_speed_rpm": 6200,
    "max_rpm": 6200,
    "speed_oil_rpm": 8300,
    "weight_g": 705,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7014 is the 70 mm bore member of NTN's standard-section 7000 single-row family, with a 110 mm outside diameter and 20 mm section width. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 20.0 mm, and the catalogue couples that with C 47.5 kN / C0 39.5 kN. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 70 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Grease rated for deep-groove motor duty is not automatically right at 6,200 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 47.5/39.5 kN ratings and 2.78 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7014; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7014?",
        "a": "7014 is a single-row angular contact ball bearing to ISO 15: 70 mm bore, 110 mm outside diameter, 20 mm width (2.756 x 4.331 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 47.5 kN, C0 39.5 kN and a 2.78 kN fatigue load limit Pu; the grease limiting speed is 6,200 r/min and the oil rating 8,300 r/min; mass about 705 g."
      },
      {
        "q": "How is the 7014 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 110 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7014 support?",
        "a": "One 7014 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7014?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,200 r/min and the oil rating 8,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7014?",
        "a": "The 70/110/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 47.5 kN / C0 39.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7014",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7014",
      "7014-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5214S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5214S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 94,
    "static_load_kN": 82,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4500,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 5200S double-row family, 5214S measures 70 mm across the bore, 125 mm over the outer ring and 39.7 mm across the faces. Reading the code: 52 is the double-row dimension series (medium-duty 5200S double-row family), 14 encodes the 70 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. With C 94 kN and C0 82 kN, each mm of bore carries about 1.34 kN of dynamic rating. The 70/125/39.7 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. A 70 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "Do not pair two random 5214S bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "On a 70 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 94/82 kN ratings and 5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5214S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5214S?",
        "a": "5214S is a double-row angular contact ball bearing to ISO 15: 70 mm bore, 125 mm outside diameter, 39.7 mm width (2.756 x 4.921 x 1.563 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 94 kN, C0 82 kN and a 5 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min; mass about 1750 g."
      },
      {
        "q": "How is the 5214S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 14 encodes the 70 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 125 mm OD and 39.7 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5214S support?",
        "a": "5214S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5214S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5214S?",
        "a": "The 70/125/39.7 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 94 kN / C0 82 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5214S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5214s",
      "5214S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7214",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 84.5,
    "static_load_kN": 63.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5,
    "limiting_speed_rpm": 5700,
    "max_rpm": 5700,
    "speed_oil_rpm": 7600,
    "weight_g": 1090,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 is the 70 mm bore member of NTN's medium-duty 7200 single-row family, with a 125 mm outside diameter and 24 mm section width. Decoding 7214: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 63.5 kN static rating into useful one-direction thrust capacity. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. A 70 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A 7214 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 84.5/63.5 kN ratings and 5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7214; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7214?",
        "a": "7214 is a single-row angular contact ball bearing to ISO 15: 70 mm bore, 125 mm outside diameter, 24 mm width (2.756 x 4.921 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 84.5 kN, C0 63.5 kN and a 5 kN fatigue load limit Pu; the grease limiting speed is 5,700 r/min and the oil rating 7,600 r/min; mass about 1090 g."
      },
      {
        "q": "How is the 7214 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 125 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7214 support?",
        "a": "One 7214 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7214?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,700 r/min and the oil rating 7,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7214?",
        "a": "The 70/125/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 84.5 kN / C0 63.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214",
      "7214-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7214B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 76.5,
    "static_load_kN": 58,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.35,
    "limiting_speed_rpm": 4900,
    "max_rpm": 4900,
    "speed_oil_rpm": 6500,
    "weight_g": 1110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7214B carries a 70 mm bore in a 125 mm outside diameter, 24 mm wide envelope. Decoding 7214B: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 14 encodes the 70 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The radial section height here is 27.5 mm, and the catalogue couples that with C 76.5 kN / C0 58 kN. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The C0 of 58 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 76.5/58 kN ratings and 4.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7214B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7214B?",
        "a": "7214B is a single-row angular contact ball bearing to ISO 15: 70 mm bore, 125 mm outside diameter, 24 mm width (2.756 x 4.921 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 76.5 kN, C0 58 kN and a 4.35 kN fatigue load limit Pu; the grease limiting speed is 4,900 r/min and the oil rating 6,500 r/min; mass about 1110 g."
      },
      {
        "q": "How is the 7214B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 14 encodes the 70 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 125 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7214B support?",
        "a": "One 7214B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7214B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,900 r/min and the oil rating 6,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7214B?",
        "a": "The 70/125/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 76.5 kN / C0 58 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214b",
      "7214B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ214",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ214",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 102,
    "static_load_kN": 168,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 7.15,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "speed_oil_rpm": 5400,
    "weight_g": 1360,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty QJ200 four-point family entry QJ214 carries a 70 mm bore in a 125 mm outside diameter, 24 mm wide envelope. Two fields make up the code — QJ2 is the four-point dimension series (medium-duty QJ200 four-point family) and the last two digits 14 give the bore by the standard code table (70 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Catalogue dynamic rating C is 102 kN against C0 168 kN — a C0/C ratio of 1.65 that is typical of an angular-contact contact ellipse. For a 70 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "On a 70 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The C0 of 168 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 102/168 kN ratings and 7.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ214; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ214?",
        "a": "QJ214 is a four-point contact ball bearing to ISO 15: 70 mm bore, 125 mm outside diameter, 24 mm width (2.756 x 4.921 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 102 kN, C0 168 kN and a 7.15 kN fatigue load limit Pu; the grease limiting speed is 4,000 r/min and the oil rating 5,400 r/min; mass about 1360 g."
      },
      {
        "q": "How is the QJ214 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 14 give the bore by the standard code table (70 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 125 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ214 support?",
        "a": "QJ214 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ214?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,000 r/min and the oil rating 5,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ214?",
        "a": "The 70/125/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 102 kN / C0 168 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ214",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj214",
      "QJ214"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5314S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5314S",
    "series": "5300S-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 63.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 159,
    "static_load_kN": 128,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7.9,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 3800,
    "weight_g": 4550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 70 x 150 x 63.5 mm, NTN 5314S sits in the heavy-duty 5300S double-row family of the angular-contact programme. NTN builds the number from 53 is the double-row dimension series (heavy-duty 5300S double-row family), then 14 encodes the 70 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The oil rating of 3,800 r/min sits 800 r/min above the 3,000 r/min grease figure — a 1.27x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "A 5314S mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 159/128 kN ratings and 7.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5314S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5314S?",
        "a": "5314S is a double-row angular contact ball bearing to ISO 15: 70 mm bore, 150 mm outside diameter, 63.5 mm width (2.756 x 5.906 x 2.5 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 159 kN, C0 128 kN and a 7.9 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 3,800 r/min; mass about 4550 g."
      },
      {
        "q": "How is the 5314S designation structured?",
        "a": "53 is the double-row dimension series (heavy-duty 5300S double-row family); 14 encodes the 70 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 150 mm OD and 63.5 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5314S support?",
        "a": "5314S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5314S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 3,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5314S?",
        "a": "The 70/150/63.5 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 159 kN / C0 128 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5314S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5314s",
      "5314S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7314",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 138,
    "static_load_kN": 93.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6.95,
    "limiting_speed_rpm": 5100,
    "max_rpm": 5100,
    "speed_oil_rpm": 6800,
    "weight_g": 2560,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 70 x 150 x 35 mm, NTN 7314 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 40.0 mm, and the catalogue couples that with C 138 kN / C0 93.5 kN. Against a deep-groove bearing of the same 70 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 70 mm bore give the working limits. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Do not pair two random 7314 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Do not pair two random 7314 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 138/93.5 kN ratings and 6.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7314; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7314?",
        "a": "7314 is a single-row angular contact ball bearing to ISO 15: 70 mm bore, 150 mm outside diameter, 35 mm width (2.756 x 5.906 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 138 kN, C0 93.5 kN and a 6.95 kN fatigue load limit Pu; the grease limiting speed is 5,100 r/min and the oil rating 6,800 r/min; mass about 2560 g."
      },
      {
        "q": "How is the 7314 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 14 encodes the 70 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 150 mm OD and 35 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7314 support?",
        "a": "One 7314 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7314?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,100 r/min and the oil rating 6,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7314?",
        "a": "The 70/150/35 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 138 kN / C0 93.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314",
      "7314-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7314B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 127,
    "static_load_kN": 86,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6.4,
    "limiting_speed_rpm": 4400,
    "max_rpm": 4400,
    "speed_oil_rpm": 5800,
    "weight_g": 2610,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7314B appears as a heavy-duty 7300 single-row family bearing of 70 mm bore, 150 mm outside diameter and 35 mm width. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 14 encodes the 70 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). On speed, the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Heat-mounting to 80-90 deg C is the clean route onto a 70 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7314B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The C0 of 86 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 127/86 kN ratings and 6.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7314B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7314B?",
        "a": "7314B is a single-row angular contact ball bearing to ISO 15: 70 mm bore, 150 mm outside diameter, 35 mm width (2.756 x 5.906 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 127 kN, C0 86 kN and a 6.4 kN fatigue load limit Pu; the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min; mass about 2610 g."
      },
      {
        "q": "How is the 7314B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 14 encodes the 70 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 150 mm OD and 35 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7314B support?",
        "a": "One 7314B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7314B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7314B?",
        "a": "The 70/150/35 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 127 kN / C0 86 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314b",
      "7314B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ314",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ314",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 172,
    "static_load_kN": 260,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 10.7,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "speed_oil_rpm": 4800,
    "weight_g": 3270,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ314 is the 70 mm bore member of NTN's heavy-duty QJ300 four-point family, with a 150 mm outside diameter and 35 mm section width. Reading the code: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), the last two digits 14 give the bore by the standard code table (70 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Size selection is usually finished by checking that the C0 of 260 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 70 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 3,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 172/260 kN ratings and 10.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ314; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ314?",
        "a": "QJ314 is a four-point contact ball bearing to ISO 15: 70 mm bore, 150 mm outside diameter, 35 mm width (2.756 x 5.906 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 172 kN, C0 260 kN and a 10.7 kN fatigue load limit Pu; the grease limiting speed is 3,600 r/min and the oil rating 4,800 r/min; mass about 3270 g."
      },
      {
        "q": "How is the QJ314 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 14 give the bore by the standard code table (70 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 150 mm OD and 35 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ314 support?",
        "a": "QJ314 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ314?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,600 r/min and the oil rating 4,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ314?",
        "a": "The 70/150/35 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 172 kN / C0 260 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ314",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj314",
      "QJ314"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7915",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7915",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 105,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 29.4,
    "static_load_kN": 27.1,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "speed_oil_rpm": 8400,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7915 is an NTN single-row angular contact ball bearing: extra-light, high-speed 7900 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 75 x 105 x 16 mm. Decoding 7915: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 29.4 kN and C0 27.1 kN, each mm of bore carries about 0.39 kN of dynamic rating. The 75/105/16 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 27.1 kN really covers the worst static case before substituting it for a 7000.",
      "A 7915 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 6,300 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "On a 75 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 29.4/27.1 kN ratings and 1.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7915; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7915?",
        "a": "7915 is a single-row angular contact ball bearing to ISO 15: 75 mm bore, 105 mm outside diameter, 16 mm width (2.953 x 4.134 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 29.4 kN, C0 27.1 kN and a 1.8 kN fatigue load limit Pu; the grease limiting speed is 6,300 r/min and the oil rating 8,400 r/min; mass about 420 g."
      },
      {
        "q": "How is the 7915 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 105 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7915 support?",
        "a": "One 7915 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7915?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 6,300 r/min and the oil rating 8,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7915?",
        "a": "The 75/105/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 29.4 kN / C0 27.1 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7915",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7915"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7015-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7015",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 115,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 48.5,
    "static_load_kN": 41.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 2.9,
    "limiting_speed_rpm": 5800,
    "max_rpm": 5800,
    "speed_oil_rpm": 7800,
    "weight_g": 745,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 75 x 115 x 20 mm, NTN 7015 sits in the standard-section 7000 single-row family of the angular-contact programme. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 5,800 r/min and the oil rating 7,800 r/min. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Heat-mounting to 80-90 deg C is the clean route onto a 75 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "On a 75 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The C0 of 41.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 48.5/41.5 kN ratings and 2.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7015; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7015?",
        "a": "7015 is a single-row angular contact ball bearing to ISO 15: 75 mm bore, 115 mm outside diameter, 20 mm width (2.953 x 4.528 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 48.5 kN, C0 41.5 kN and a 2.9 kN fatigue load limit Pu; the grease limiting speed is 5,800 r/min and the oil rating 7,800 r/min; mass about 745 g."
      },
      {
        "q": "How is the 7015 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 115 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7015 support?",
        "a": "One 7015 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7015?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,800 r/min and the oil rating 7,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7015?",
        "a": "The 75/115/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 48.5 kN / C0 41.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7015",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7015",
      "7015-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5215S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5215S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 41.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 93.5,
    "static_load_kN": 83,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.1,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4300,
    "weight_g": 1880,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 5215S belongs to the medium-duty 5200S double-row family: the catalogue boundary dimensions read 75 / 130 / 41.3 mm (bore / OD / width). Decoding 5215S: 52 is the double-row dimension series (medium-duty 5200S double-row family), with 15 encodes the 75 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The oil rating of 4,300 r/min sits 1,100 r/min above the 3,200 r/min grease figure — a 1.34x step that says how much headroom oil cooling buys. Size selection is usually finished by checking that the C0 of 83 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The C0 of 83 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The C0 of 83 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,200 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 93.5/83 kN ratings and 5.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5215S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5215S?",
        "a": "5215S is a double-row angular contact ball bearing to ISO 15: 75 mm bore, 130 mm outside diameter, 41.3 mm width (2.953 x 5.118 x 1.626 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 93.5 kN, C0 83 kN and a 5.1 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min; mass about 1880 g."
      },
      {
        "q": "How is the 5215S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 15 encodes the 75 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 130 mm OD and 41.3 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5215S support?",
        "a": "5215S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5215S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5215S?",
        "a": "The 75/130/41.3 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 93.5 kN / C0 83 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5215S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5215s",
      "5215S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7215",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 87.5,
    "static_load_kN": 68.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.2,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "speed_oil_rpm": 7100,
    "weight_g": 1170,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 75 x 130 x 25 mm, NTN 7215 sits in the medium-duty 7200 single-row family of the angular-contact programme. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 87.5 kN and C0 68.5 kN, each mm of bore carries about 1.17 kN of dynamic rating. Size selection is usually finished by checking that the C0 of 68.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 75 mm bore give the working limits. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "On a 75 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 87.5/68.5 kN ratings and 5.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7215; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7215?",
        "a": "7215 is a single-row angular contact ball bearing to ISO 15: 75 mm bore, 130 mm outside diameter, 25 mm width (2.953 x 5.118 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 87.5 kN, C0 68.5 kN and a 5.2 kN fatigue load limit Pu; the grease limiting speed is 5,300 r/min and the oil rating 7,100 r/min; mass about 1170 g."
      },
      {
        "q": "How is the 7215 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 130 mm OD and 25 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7215 support?",
        "a": "One 7215 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7215?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,300 r/min and the oil rating 7,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7215?",
        "a": "The 75/130/25 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 87.5 kN / C0 68.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215",
      "7215-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7215B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 79,
    "static_load_kN": 62,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.5,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "speed_oil_rpm": 6000,
    "weight_g": 1190,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7215B measures 75 mm across the bore, 130 mm over the outer ring and 25 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 15 encodes the 75 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). On speed, the grease limiting speed is 4,500 r/min and the oil rating 6,000 r/min. For a 75 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. Grease quantity matters as much as grade at 4,500 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7215B without re-checking axial float, heat and housing width — the kinematics differ.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The C0 of 62 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 79/62 kN ratings and 4.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7215B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7215B?",
        "a": "7215B is a single-row angular contact ball bearing to ISO 15: 75 mm bore, 130 mm outside diameter, 25 mm width (2.953 x 5.118 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 79 kN, C0 62 kN and a 4.5 kN fatigue load limit Pu; the grease limiting speed is 4,500 r/min and the oil rating 6,000 r/min; mass about 1190 g."
      },
      {
        "q": "How is the 7215B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 15 encodes the 75 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 130 mm OD and 25 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7215B support?",
        "a": "One 7215B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7215B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,500 r/min and the oil rating 6,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7215B?",
        "a": "The 75/130/25 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 79 kN / C0 62 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215b",
      "7215B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ215",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ215",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 106,
    "static_load_kN": 183,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 7.55,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "speed_oil_rpm": 5000,
    "weight_g": 1530,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 75 x 130 x 25 mm, NTN QJ215 sits in the medium-duty QJ200 four-point family of the angular-contact programme. Decoding QJ215: QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), with the last two digits 15 give the bore by the standard code table (75 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. At roughly 27.5 mm of radial section, the catalogue still quotes 106 kN dynamic capacity for the 75 mm bore. Against a deep-groove bearing of the same 75 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 75 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ215 without re-checking axial float, heat and housing width — the kinematics differ.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 106/183 kN ratings and 7.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ215; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ215?",
        "a": "QJ215 is a four-point contact ball bearing to ISO 15: 75 mm bore, 130 mm outside diameter, 25 mm width (2.953 x 5.118 x 0.984 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 106 kN, C0 183 kN and a 7.55 kN fatigue load limit Pu; the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min; mass about 1530 g."
      },
      {
        "q": "How is the QJ215 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 15 give the bore by the standard code table (75 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 130 mm OD and 25 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ215 support?",
        "a": "QJ215 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ215?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ215?",
        "a": "The 75/130/25 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 106 kN / C0 183 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ215",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj215",
      "QJ215"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7315",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 150,
    "static_load_kN": 106,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7.65,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "speed_oil_rpm": 6300,
    "weight_g": 3070,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7315 is the 75 mm bore member of NTN's heavy-duty 7300 single-row family, with a 160 mm outside diameter and 37 mm section width. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 106 kN static rating into useful one-direction thrust capacity. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 75 mm bore give the working limits. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The C0 of 106 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A 7315 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 150/106 kN ratings and 7.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7315; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7315?",
        "a": "7315 is a single-row angular contact ball bearing to ISO 15: 75 mm bore, 160 mm outside diameter, 37 mm width (2.953 x 6.299 x 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 150 kN, C0 106 kN and a 7.65 kN fatigue load limit Pu; the grease limiting speed is 4,800 r/min and the oil rating 6,300 r/min; mass about 3070 g."
      },
      {
        "q": "How is the 7315 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 15 encodes the 75 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 160 mm OD and 37 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7315 support?",
        "a": "One 7315 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7315?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,800 r/min and the oil rating 6,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7315?",
        "a": "The 75/160/37 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 150 kN / C0 106 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315",
      "7315-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7315B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 138,
    "static_load_kN": 97.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7,
    "limiting_speed_rpm": 4100,
    "max_rpm": 4100,
    "speed_oil_rpm": 5400,
    "weight_g": 3130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 75 x 160 x 37 mm, NTN 7315B sits in the heavy-duty 7300 single-row family of the angular-contact programme. Decoding 7315B: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 15 encodes the 75 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The static margin, C0 97.5 kN versus C 138 kN, is what supports slow oscillating duty and shock without immediate brinelling. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 75 mm bore give the working limits. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,100 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Do not pair two random 7315B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 138/97.5 kN ratings and 7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7315B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7315B?",
        "a": "7315B is a single-row angular contact ball bearing to ISO 15: 75 mm bore, 160 mm outside diameter, 37 mm width (2.953 x 6.299 x 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 138 kN, C0 97.5 kN and a 7 kN fatigue load limit Pu; the grease limiting speed is 4,100 r/min and the oil rating 5,400 r/min; mass about 3130 g."
      },
      {
        "q": "How is the 7315B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 15 encodes the 75 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 160 mm OD and 37 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7315B support?",
        "a": "One 7315B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7315B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,100 r/min and the oil rating 5,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7315B?",
        "a": "The 75/160/37 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 138 kN / C0 97.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315b",
      "7315B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ315",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ315",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 187,
    "static_load_kN": 294,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 11.7,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4500,
    "weight_g": 3900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty QJ300 four-point family, QJ315 measures 75 mm across the bore, 160 mm over the outer ring and 37 mm across the faces. Two fields make up the code — QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family) and the last two digits 15 give the bore by the standard code table (75 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Catalogue mass is about 3900 g, which at this 42.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. A 75 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 75 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 187/294 kN ratings and 11.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ315; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ315?",
        "a": "QJ315 is a four-point contact ball bearing to ISO 15: 75 mm bore, 160 mm outside diameter, 37 mm width (2.953 x 6.299 x 1.457 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 187 kN, C0 294 kN and a 11.7 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min; mass about 3900 g."
      },
      {
        "q": "How is the QJ315 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 15 give the bore by the standard code table (75 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 160 mm OD and 37 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ315 support?",
        "a": "QJ315 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ315?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ315?",
        "a": "The 75/160/37 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 187 kN / C0 294 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ315",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj315",
      "QJ315"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7916",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7916",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 110,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 29.8,
    "static_load_kN": 28,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 1.86,
    "limiting_speed_rpm": 5900,
    "max_rpm": 5900,
    "speed_oil_rpm": 7800,
    "weight_g": 444,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7916 appears as a extra-light, high-speed 7900 single-row family bearing of 80 mm bore, 110 mm outside diameter and 16 mm width. NTN builds the number from 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), then 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 28 kN versus C 29.8 kN, is what supports slow oscillating duty and shock without immediate brinelling. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 5,900 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 28 kN really covers the worst static case before substituting it for a 7000.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Do not pair two random 7916 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 29.8/28 kN ratings and 1.86 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7916; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7916?",
        "a": "7916 is a single-row angular contact ball bearing to ISO 15: 80 mm bore, 110 mm outside diameter, 16 mm width (3.15 x 4.331 x 0.63 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 29.8 kN, C0 28 kN and a 1.86 kN fatigue load limit Pu; the grease limiting speed is 5,900 r/min and the oil rating 7,800 r/min; mass about 444 g."
      },
      {
        "q": "How is the 7916 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 110 mm OD and 16 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7916 support?",
        "a": "One 7916 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7916?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,900 r/min and the oil rating 7,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7916?",
        "a": "The 80/110/16 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 29.8 kN / C0 28 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7916",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7916"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7016-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7016",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 125,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 59,
    "static_load_kN": 50.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.5,
    "limiting_speed_rpm": 5500,
    "max_rpm": 5500,
    "speed_oil_rpm": 7300,
    "weight_g": 994,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7016 is the 80 mm bore member of NTN's standard-section 7000 single-row family, with a 125 mm outside diameter and 22 mm section width. NTN builds the number from 70 is the single-row dimension series (standard-section 7000 single-row family), then 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 59 kN and C0 50.5 kN, each mm of bore carries about 0.74 kN of dynamic rating. For a 80 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. Heat-mounting to 80-90 deg C is the clean route onto a 80 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A 7016 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "On a 80 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 59/50.5 kN ratings and 3.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7016; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7016?",
        "a": "7016 is a single-row angular contact ball bearing to ISO 15: 80 mm bore, 125 mm outside diameter, 22 mm width (3.15 x 4.921 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 59 kN, C0 50.5 kN and a 3.5 kN fatigue load limit Pu; the grease limiting speed is 5,500 r/min and the oil rating 7,300 r/min; mass about 994 g."
      },
      {
        "q": "How is the 7016 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 125 mm OD and 22 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7016 support?",
        "a": "One 7016 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7016?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,500 r/min and the oil rating 7,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7016?",
        "a": "The 80/125/22 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 59 kN / C0 50.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7016",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7016",
      "7016-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5216S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5216S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 99,
    "static_load_kN": 93,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.7,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 3800,
    "weight_g": 2510,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "5216S is the 80 mm bore member of NTN's medium-duty 5200S double-row family, with a 140 mm outside diameter and 44.4 mm section width. The designation breaks down as 52 is the double-row dimension series (medium-duty 5200S double-row family); 16 encodes the 80 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. At roughly 30.0 mm of radial section, the catalogue still quotes 99 kN dynamic capacity for the 80 mm bore. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Grease quantity matters as much as grade at 3,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 99/93 kN ratings and 5.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5216S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5216S?",
        "a": "5216S is a double-row angular contact ball bearing to ISO 15: 80 mm bore, 140 mm outside diameter, 44.4 mm width (3.15 x 5.512 x 1.748 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 99 kN, C0 93 kN and a 5.7 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 3,800 r/min; mass about 2510 g."
      },
      {
        "q": "How is the 5216S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 16 encodes the 80 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 140 mm OD and 44.4 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5216S support?",
        "a": "5216S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5216S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 3,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5216S?",
        "a": "The 80/140/44.4 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 99 kN / C0 93 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5216S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5216s",
      "5216S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7216",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 98.5,
    "static_load_kN": 76,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.65,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "speed_oil_rpm": 6600,
    "weight_g": 1390,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 is the 80 mm bore member of NTN's medium-duty 7200 single-row family, with a 140 mm outside diameter and 26 mm section width. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 76 kN versus C 98.5 kN, is what supports slow oscillating duty and shock without immediate brinelling. The 80/140/26 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 80 mm bore give the working limits. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 80 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 80 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Do not pair two random 7216 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 98.5/76 kN ratings and 5.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7216; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7216?",
        "a": "7216 is a single-row angular contact ball bearing to ISO 15: 80 mm bore, 140 mm outside diameter, 26 mm width (3.15 x 5.512 x 1.024 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 98.5 kN, C0 76 kN and a 5.65 kN fatigue load limit Pu; the grease limiting speed is 5,000 r/min and the oil rating 6,600 r/min; mass about 1390 g."
      },
      {
        "q": "How is the 7216 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 140 mm OD and 26 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7216 support?",
        "a": "One 7216 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7216?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,000 r/min and the oil rating 6,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7216?",
        "a": "The 80/140/26 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 98.5 kN / C0 76 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216",
      "7216-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7216B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 89,
    "static_load_kN": 69.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.9,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "speed_oil_rpm": 5700,
    "weight_g": 1420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7216B belongs to the medium-duty 7200 single-row family: the catalogue boundary dimensions read 80 / 140 / 26 mm (bore / OD / width). Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 16 encodes the 80 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The static margin, C0 69.5 kN versus C 89 kN, is what supports slow oscillating duty and shock without immediate brinelling. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7216B without re-checking axial float, heat and housing width — the kinematics differ.",
      "Do not pair two random 7216B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 89/69.5 kN ratings and 4.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7216B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7216B?",
        "a": "7216B is a single-row angular contact ball bearing to ISO 15: 80 mm bore, 140 mm outside diameter, 26 mm width (3.15 x 5.512 x 1.024 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 89 kN, C0 69.5 kN and a 4.9 kN fatigue load limit Pu; the grease limiting speed is 4,300 r/min and the oil rating 5,700 r/min; mass about 1420 g."
      },
      {
        "q": "How is the 7216B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 16 encodes the 80 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 140 mm OD and 26 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7216B support?",
        "a": "One 7216B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7216B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,300 r/min and the oil rating 5,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7216B?",
        "a": "The 80/140/26 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 89 kN / C0 69.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216b",
      "7216B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ216",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ216",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 124,
    "static_load_kN": 217,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 8.65,
    "limiting_speed_rpm": 3500,
    "max_rpm": 3500,
    "speed_oil_rpm": 4700,
    "weight_g": 1830,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ216 is the 80 mm bore member of NTN's medium-duty QJ200 four-point family, with a 140 mm outside diameter and 26 mm section width. NTN builds the number from QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), then the last two digits 16 give the bore by the standard code table (80 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. NTN prints 124 kN dynamic and 217 kN static for this size and a 8.65 kN fatigue load limit Pu. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "The C0 of 217 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ216 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 124/217 kN ratings and 8.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ216; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ216?",
        "a": "QJ216 is a four-point contact ball bearing to ISO 15: 80 mm bore, 140 mm outside diameter, 26 mm width (3.15 x 5.512 x 1.024 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 124 kN, C0 217 kN and a 8.65 kN fatigue load limit Pu; the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min; mass about 1830 g."
      },
      {
        "q": "How is the QJ216 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 16 give the bore by the standard code table (80 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 140 mm OD and 26 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ216 support?",
        "a": "QJ216 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ216?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ216?",
        "a": "The 80/140/26 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 124 kN / C0 217 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ216",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj216",
      "QJ216"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7316",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 163,
    "static_load_kN": 119,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.3,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "speed_oil_rpm": 5900,
    "weight_g": 3650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7316 measures 80 mm across the bore, 170 mm over the outer ring and 39 mm across the faces. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 4,500 r/min and the oil rating 5,900 r/min. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 80 mm bore give the working limits. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The C0 of 119 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 163/119 kN ratings and 8.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7316; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7316?",
        "a": "7316 is a single-row angular contact ball bearing to ISO 15: 80 mm bore, 170 mm outside diameter, 39 mm width (3.15 x 6.693 x 1.535 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 163 kN, C0 119 kN and a 8.3 kN fatigue load limit Pu; the grease limiting speed is 4,500 r/min and the oil rating 5,900 r/min; mass about 3650 g."
      },
      {
        "q": "How is the 7316 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 16 encodes the 80 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 170 mm OD and 39 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7316 support?",
        "a": "One 7316 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7316?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,500 r/min and the oil rating 5,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7316?",
        "a": "The 80/170/39 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 163 kN / C0 119 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316",
      "7316-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7316B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 149,
    "static_load_kN": 109,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7.65,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "speed_oil_rpm": 5100,
    "weight_g": 3720,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316B is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 80 x 170 x 39 mm. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 16 encodes the 80 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue dynamic rating C is 149 kN against C0 109 kN — a C0/C ratio of 0.73 that is typical of an angular-contact contact ellipse. The 80/170/39 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "On a 80 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 80 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 149/109 kN ratings and 7.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7316B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7316B?",
        "a": "7316B is a single-row angular contact ball bearing to ISO 15: 80 mm bore, 170 mm outside diameter, 39 mm width (3.15 x 6.693 x 1.535 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 149 kN, C0 109 kN and a 7.65 kN fatigue load limit Pu; the grease limiting speed is 3,800 r/min and the oil rating 5,100 r/min; mass about 3720 g."
      },
      {
        "q": "How is the 7316B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 16 encodes the 80 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 170 mm OD and 39 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7316B support?",
        "a": "One 7316B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7316B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,800 r/min and the oil rating 5,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7316B?",
        "a": "The 80/170/39 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 149 kN / C0 109 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316b",
      "7316B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ316",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ316",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 202,
    "static_load_kN": 330,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 12.7,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4200,
    "weight_g": 4640,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ316 is an NTN four-point contact ball bearing: heavy-duty QJ300 four-point family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 80 x 170 x 39 mm. Decoding QJ316: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), with the last two digits 16 give the bore by the standard code table (80 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The radial section height here is 45.0 mm, and the catalogue couples that with C 202 kN / C0 330 kN. For a 80 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 80 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,200 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random QJ316 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 202/330 kN ratings and 12.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ316; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ316?",
        "a": "QJ316 is a four-point contact ball bearing to ISO 15: 80 mm bore, 170 mm outside diameter, 39 mm width (3.15 x 6.693 x 1.535 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 202 kN, C0 330 kN and a 12.7 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,200 r/min; mass about 4640 g."
      },
      {
        "q": "How is the QJ316 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 16 give the bore by the standard code table (80 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 170 mm OD and 39 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ316 support?",
        "a": "QJ316 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ316?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ316?",
        "a": "The 80/170/39 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 202 kN / C0 330 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ316",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj316",
      "QJ316"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7917",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7917",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 120,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 40,
    "static_load_kN": 38,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 2.49,
    "limiting_speed_rpm": 5500,
    "max_rpm": 5500,
    "speed_oil_rpm": 7400,
    "weight_g": 628,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7917 belongs to the extra-light, high-speed 7900 single-row family: the catalogue boundary dimensions read 85 / 120 / 18 mm (bore / OD / width). The designation breaks down as 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 7,400 r/min sits 1,900 r/min above the 5,500 r/min grease figure — a 1.35x step that says how much headroom oil cooling buys. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 38 kN really covers the worst static case before substituting it for a 7000.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 85 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 40/38 kN ratings and 2.49 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7917; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7917?",
        "a": "7917 is a single-row angular contact ball bearing to ISO 15: 85 mm bore, 120 mm outside diameter, 18 mm width (3.346 x 4.724 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 40 kN, C0 38 kN and a 2.49 kN fatigue load limit Pu; the grease limiting speed is 5,500 r/min and the oil rating 7,400 r/min; mass about 628 g."
      },
      {
        "q": "How is the 7917 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 120 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7917 support?",
        "a": "One 7917 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7917?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,500 r/min and the oil rating 7,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7917?",
        "a": "The 85/120/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 40 kN / C0 38 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7917",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7917"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7017-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7017",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 130,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 60.5,
    "static_load_kN": 53.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 3.6,
    "limiting_speed_rpm": 5100,
    "max_rpm": 5100,
    "speed_oil_rpm": 6900,
    "weight_g": 1040,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 85 x 130 x 22 mm, NTN 7017 sits in the standard-section 7000 single-row family of the angular-contact programme. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Against a deep-groove bearing of the same 85 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 85 mm bore give the working limits. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 53.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 5,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 60.5/53.5 kN ratings and 3.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7017; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7017?",
        "a": "7017 is a single-row angular contact ball bearing to ISO 15: 85 mm bore, 130 mm outside diameter, 22 mm width (3.346 x 5.118 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 60.5 kN, C0 53.5 kN and a 3.6 kN fatigue load limit Pu; the grease limiting speed is 5,100 r/min and the oil rating 6,900 r/min; mass about 1040 g."
      },
      {
        "q": "How is the 7017 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 130 mm OD and 22 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7017 support?",
        "a": "One 7017 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7017?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,100 r/min and the oil rating 6,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7017?",
        "a": "The 85/130/22 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 60.5 kN / C0 53.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7017",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7017",
      "7017-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "5217S",
    "brand": "NTN",
    "manufacturer_designation": "NTN 5217S",
    "series": "5200S-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 116,
    "static_load_kN": 110,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6.7,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3600,
    "weight_g": 3160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 5217S appears as a medium-duty 5200S double-row family bearing of 85 mm bore, 150 mm outside diameter and 49.2 mm width. Two fields make up the code — 52 is the double-row dimension series (medium-duty 5200S double-row family) and 17 encodes the 85 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Choose the medium-duty 5200S double-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The double-row bearing takes reversing thrust in one envelope, but its two contact lines mean more heat than a single row at the same speed — check the thermal balance before copying a single-row speed figure.",
      "The 2,800 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 5217S without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 2,800 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 116/110 kN ratings and 6.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 5217S; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 5217S?",
        "a": "5217S is a double-row angular contact ball bearing to ISO 15: 85 mm bore, 150 mm outside diameter, 49.2 mm width (3.346 x 5.906 x 1.937 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 116 kN, C0 110 kN and a 6.7 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,600 r/min; mass about 3160 g."
      },
      {
        "q": "How is the 5217S designation structured?",
        "a": "52 is the double-row dimension series (medium-duty 5200S double-row family); 17 encodes the 85 mm bore (bore code x 5), and the trailing S marks the current internal design of the family. The 150 mm OD and 49.2 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 5217S support?",
        "a": "5217S is a double-row bearing working like a built-in back-to-back pair: it takes thrust in both directions plus radial load and moment (tilting) load in a single envelope."
      },
      {
        "q": "What lubrication speeds does NTN print for 5217S?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,800 r/min and the oil rating 3,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 5217S?",
        "a": "The 85/150/49.2 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 116 kN / C0 110 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "5217S",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=135",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "5217s",
      "5217S"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7217",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 110,
    "static_load_kN": 88.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6.25,
    "limiting_speed_rpm": 4700,
    "max_rpm": 4700,
    "speed_oil_rpm": 6200,
    "weight_g": 1780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7217 measures 85 mm across the bore, 150 mm over the outer ring and 28 mm across the faces. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 6,200 r/min sits 1,500 r/min above the 4,700 r/min grease figure — a 1.32x step that says how much headroom oil cooling buys. Size selection is usually finished by checking that the C0 of 88.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 85 mm bore give the working limits. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A 7217 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 110/88.5 kN ratings and 6.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7217; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7217?",
        "a": "7217 is a single-row angular contact ball bearing to ISO 15: 85 mm bore, 150 mm outside diameter, 28 mm width (3.346 x 5.906 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 110 kN, C0 88.5 kN and a 6.25 kN fatigue load limit Pu; the grease limiting speed is 4,700 r/min and the oil rating 6,200 r/min; mass about 1780 g."
      },
      {
        "q": "How is the 7217 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 150 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7217 support?",
        "a": "One 7217 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7217?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,700 r/min and the oil rating 6,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7217?",
        "a": "The 85/150/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 110 kN / C0 88.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217",
      "7217-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7217B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 99.5,
    "static_load_kN": 80.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.45,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "speed_oil_rpm": 5300,
    "weight_g": 1820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7217B is the 85 mm bore member of NTN's medium-duty 7200 single-row family, with a 150 mm outside diameter and 28 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 17 encodes the 85 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue dynamic rating C is 99.5 kN against C0 80.5 kN — a C0/C ratio of 0.81 that is typical of an angular-contact contact ellipse. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 85 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Do not pair two random 7217B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 99.5/80.5 kN ratings and 5.45 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7217B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7217B?",
        "a": "7217B is a single-row angular contact ball bearing to ISO 15: 85 mm bore, 150 mm outside diameter, 28 mm width (3.346 x 5.906 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 99.5 kN, C0 80.5 kN and a 5.45 kN fatigue load limit Pu; the grease limiting speed is 4,000 r/min and the oil rating 5,300 r/min; mass about 1820 g."
      },
      {
        "q": "How is the 7217B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 17 encodes the 85 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 150 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7217B support?",
        "a": "One 7217B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7217B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,000 r/min and the oil rating 5,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7217B?",
        "a": "The 85/150/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 99.5 kN / C0 80.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=130",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217b",
      "7217B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ217",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ217",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 139,
    "static_load_kN": 252,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 9.65,
    "limiting_speed_rpm": 3300,
    "max_rpm": 3300,
    "speed_oil_rpm": 4400,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty QJ200 four-point family, QJ217 measures 85 mm across the bore, 150 mm over the outer ring and 28 mm across the faces. The designation breaks down as QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 17 give the bore by the standard code table (85 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. The 85/150/28 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 85 mm bore give the working limits. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Do not pair two random QJ217 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 3,300 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 139/252 kN ratings and 9.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ217; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ217?",
        "a": "QJ217 is a four-point contact ball bearing to ISO 15: 85 mm bore, 150 mm outside diameter, 28 mm width (3.346 x 5.906 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 139 kN, C0 252 kN and a 9.65 kN fatigue load limit Pu; the grease limiting speed is 3,300 r/min and the oil rating 4,400 r/min; mass about 2300 g."
      },
      {
        "q": "How is the QJ217 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 17 give the bore by the standard code table (85 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 150 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ217 support?",
        "a": "QJ217 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ217?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,300 r/min and the oil rating 4,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ217?",
        "a": "The 85/150/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 139 kN / C0 252 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ217",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj217",
      "QJ217"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7317",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 176,
    "static_load_kN": 133,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 9,
    "limiting_speed_rpm": 4200,
    "max_rpm": 4200,
    "speed_oil_rpm": 5600,
    "weight_g": 4340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 is the 85 mm bore member of NTN's heavy-duty 7300 single-row family, with a 180 mm outside diameter and 41 mm section width. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 133 kN versus C 176 kN, is what supports slow oscillating duty and shock without immediate brinelling. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 4,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 7317 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 176/133 kN ratings and 9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7317; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7317?",
        "a": "7317 is a single-row angular contact ball bearing to ISO 15: 85 mm bore, 180 mm outside diameter, 41 mm width (3.346 x 7.087 x 1.614 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 176 kN, C0 133 kN and a 9 kN fatigue load limit Pu; the grease limiting speed is 4,200 r/min and the oil rating 5,600 r/min; mass about 4340 g."
      },
      {
        "q": "How is the 7317 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 17 encodes the 85 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 180 mm OD and 41 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7317 support?",
        "a": "One 7317 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7317?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,200 r/min and the oil rating 5,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7317?",
        "a": "The 85/180/41 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 176 kN / C0 133 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317",
      "7317-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7317B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 161,
    "static_load_kN": 122,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.3,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "speed_oil_rpm": 4800,
    "weight_g": 4430,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7317B carries a 85 mm bore in a 180 mm outside diameter, 41 mm wide envelope. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 17 encodes the 85 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). NTN prints 161 kN dynamic and 122 kN static for this size and a 8.3 kN fatigue load limit Pu. Size selection is usually finished by checking that the C0 of 122 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. A 85 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A 7317B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7317B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 161/122 kN ratings and 8.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7317B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7317B?",
        "a": "7317B is a single-row angular contact ball bearing to ISO 15: 85 mm bore, 180 mm outside diameter, 41 mm width (3.346 x 7.087 x 1.614 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 161 kN, C0 122 kN and a 8.3 kN fatigue load limit Pu; the grease limiting speed is 3,600 r/min and the oil rating 4,800 r/min; mass about 4430 g."
      },
      {
        "q": "How is the 7317B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 17 encodes the 85 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 180 mm OD and 41 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7317B support?",
        "a": "One 7317B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7317B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,600 r/min and the oil rating 4,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7317B?",
        "a": "The 85/180/41 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 161 kN / C0 122 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317b",
      "7317B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ317",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ317",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 218,
    "static_load_kN": 370,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 13.8,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 4000,
    "weight_g": 5430,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, QJ317 appears as a heavy-duty QJ300 four-point family bearing of 85 mm bore, 180 mm outside diameter and 41 mm width. NTN builds the number from QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), then the last two digits 17 give the bore by the standard code table (85 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 35 deg four-point geometry doubles the axial contact points, so the 218 kN rating is available for thrust in both directions. Against a deep-groove bearing of the same 85 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 85 mm bore give the working limits. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 85 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A QJ317 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A QJ317 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 218/370 kN ratings and 13.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ317; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ317?",
        "a": "QJ317 is a four-point contact ball bearing to ISO 15: 85 mm bore, 180 mm outside diameter, 41 mm width (3.346 x 7.087 x 1.614 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 218 kN, C0 370 kN and a 13.8 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min; mass about 5430 g."
      },
      {
        "q": "How is the QJ317 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 17 give the bore by the standard code table (85 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 180 mm OD and 41 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ317 support?",
        "a": "QJ317 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ317?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ317?",
        "a": "The 85/180/41 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 218 kN / C0 370 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ317",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj317",
      "QJ317"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7918",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7918",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 125,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 39.5,
    "static_load_kN": 38,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 2.42,
    "limiting_speed_rpm": 5200,
    "max_rpm": 5200,
    "speed_oil_rpm": 7000,
    "weight_g": 658,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The extra-light, high-speed 7900 single-row family entry 7918 carries a 90 mm bore in a 125 mm outside diameter, 18 mm wide envelope. Reading the code: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 39.5 kN against C0 38 kN — a C0/C ratio of 0.96 that is typical of an angular-contact contact ellipse. Choose the extra-light, high-speed 7900 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. A 90 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 38 kN really covers the worst static case before substituting it for a 7000.",
      "Grease rated for deep-groove motor duty is not automatically right at 5,200 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 39.5/38 kN ratings and 2.42 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7918; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7918?",
        "a": "7918 is a single-row angular contact ball bearing to ISO 15: 90 mm bore, 125 mm outside diameter, 18 mm width (3.543 x 4.921 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 39.5 kN, C0 38 kN and a 2.42 kN fatigue load limit Pu; the grease limiting speed is 5,200 r/min and the oil rating 7,000 r/min; mass about 658 g."
      },
      {
        "q": "How is the 7918 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 125 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7918 support?",
        "a": "One 7918 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7918?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,200 r/min and the oil rating 7,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7918?",
        "a": "The 90/125/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 39.5 kN / C0 38 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7918",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7918"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7018-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7018",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 140,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 72,
    "static_load_kN": 63.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.15,
    "limiting_speed_rpm": 4900,
    "max_rpm": 4900,
    "speed_oil_rpm": 6500,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7018 is the 90 mm bore member of NTN's standard-section 7000 single-row family, with a 140 mm outside diameter and 24 mm section width. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 1350 g, which at this 25.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 90 mm bore give the working limits. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 72/63.5 kN ratings and 4.15 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7018; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7018?",
        "a": "7018 is a single-row angular contact ball bearing to ISO 15: 90 mm bore, 140 mm outside diameter, 24 mm width (3.543 x 5.512 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 72 kN, C0 63.5 kN and a 4.15 kN fatigue load limit Pu; the grease limiting speed is 4,900 r/min and the oil rating 6,500 r/min; mass about 1350 g."
      },
      {
        "q": "How is the 7018 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 140 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7018 support?",
        "a": "One 7018 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7018?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,900 r/min and the oil rating 6,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7018?",
        "a": "The 90/140/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 72 kN / C0 63.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7018",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7018",
      "7018-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7218",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 130,
    "static_load_kN": 103,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7.2,
    "limiting_speed_rpm": 4400,
    "max_rpm": 4400,
    "speed_oil_rpm": 5900,
    "weight_g": 2180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7218 is the 90 mm bore member of NTN's medium-duty 7200 single-row family, with a 160 mm outside diameter and 30 mm section width. Decoding 7218: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 35.0 mm of radial section, the catalogue still quotes 130 kN dynamic capacity for the 90 mm bore. The 90/160/30 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 103 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 130/103 kN ratings and 7.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7218; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7218?",
        "a": "7218 is a single-row angular contact ball bearing to ISO 15: 90 mm bore, 160 mm outside diameter, 30 mm width (3.543 x 6.299 x 1.181 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 130 kN, C0 103 kN and a 7.2 kN fatigue load limit Pu; the grease limiting speed is 4,400 r/min and the oil rating 5,900 r/min; mass about 2180 g."
      },
      {
        "q": "How is the 7218 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 160 mm OD and 30 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7218 support?",
        "a": "One 7218 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7218?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,400 r/min and the oil rating 5,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7218?",
        "a": "The 90/160/30 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 130 kN / C0 103 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218",
      "7218-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7218B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 118,
    "static_load_kN": 94,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 6.3,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "speed_oil_rpm": 5000,
    "weight_g": 2220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7218B appears as a medium-duty 7200 single-row family bearing of 90 mm bore, 160 mm outside diameter and 30 mm width. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 18 encodes the 90 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). NTN prints 118 kN dynamic and 94 kN static for this size and a 6.3 kN fatigue load limit Pu. The 90/160/30 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 90 mm bore give the working limits. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 94 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "On a 90 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7218B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 118/94 kN ratings and 6.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7218B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7218B?",
        "a": "7218B is a single-row angular contact ball bearing to ISO 15: 90 mm bore, 160 mm outside diameter, 30 mm width (3.543 x 6.299 x 1.181 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 118 kN, C0 94 kN and a 6.3 kN fatigue load limit Pu; the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min; mass about 2220 g."
      },
      {
        "q": "How is the 7218B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 18 encodes the 90 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 160 mm OD and 30 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7218B support?",
        "a": "One 7218B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7218B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,800 r/min and the oil rating 5,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7218B?",
        "a": "The 90/160/30 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 118 kN / C0 94 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218b",
      "7218B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ218",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ218",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 164,
    "static_load_kN": 293,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 11.1,
    "limiting_speed_rpm": 3100,
    "max_rpm": 3100,
    "speed_oil_rpm": 4200,
    "weight_g": 2760,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ218 is an NTN four-point contact ball bearing: medium-duty QJ200 four-point family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 90 x 160 x 30 mm. Reading the code: QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), the last two digits 18 give the bore by the standard code table (90 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Catalogue mass is about 2760 g, which at this 35.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Heat-mounting to 80-90 deg C is the clean route onto a 90 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A QJ218 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A QJ218 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 164/293 kN ratings and 11.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ218; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ218?",
        "a": "QJ218 is a four-point contact ball bearing to ISO 15: 90 mm bore, 160 mm outside diameter, 30 mm width (3.543 x 6.299 x 1.181 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 164 kN, C0 293 kN and a 11.1 kN fatigue load limit Pu; the grease limiting speed is 3,100 r/min and the oil rating 4,200 r/min; mass about 2760 g."
      },
      {
        "q": "How is the QJ218 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 18 give the bore by the standard code table (90 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 160 mm OD and 30 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ218 support?",
        "a": "QJ218 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ218?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,100 r/min and the oil rating 4,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ218?",
        "a": "The 90/160/30 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 164 kN / C0 293 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ218",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj218",
      "QJ218"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7318",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 189,
    "static_load_kN": 147,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 9.7,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "speed_oil_rpm": 5300,
    "weight_g": 5060,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7318 measures 90 mm across the bore, 190 mm over the outer ring and 43 mm across the faces. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 5,300 r/min sits 1,300 r/min above the 4,000 r/min grease figure — a 1.32x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 189/147 kN ratings and 9.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7318; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7318?",
        "a": "7318 is a single-row angular contact ball bearing to ISO 15: 90 mm bore, 190 mm outside diameter, 43 mm width (3.543 x 7.48 x 1.693 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 189 kN, C0 147 kN and a 9.7 kN fatigue load limit Pu; the grease limiting speed is 4,000 r/min and the oil rating 5,300 r/min; mass about 5060 g."
      },
      {
        "q": "How is the 7318 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 18 encodes the 90 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 190 mm OD and 43 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7318 support?",
        "a": "One 7318 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7318?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,000 r/min and the oil rating 5,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7318?",
        "a": "The 90/190/43 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 189 kN / C0 147 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318",
      "7318-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7318B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 173,
    "static_load_kN": 135,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.95,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4500,
    "weight_g": 5160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7318B measures 90 mm across the bore, 190 mm over the outer ring and 43 mm across the faces. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 18 encodes the 90 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 5160 g, which at this 50.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 3,400 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 173/135 kN ratings and 8.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7318B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7318B?",
        "a": "7318B is a single-row angular contact ball bearing to ISO 15: 90 mm bore, 190 mm outside diameter, 43 mm width (3.543 x 7.48 x 1.693 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 173 kN, C0 135 kN and a 8.95 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min; mass about 5160 g."
      },
      {
        "q": "How is the 7318B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 18 encodes the 90 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 190 mm OD and 43 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7318B support?",
        "a": "One 7318B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7318B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7318B?",
        "a": "The 90/190/43 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 173 kN / C0 135 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318b",
      "7318B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ318",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ318",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 235,
    "static_load_kN": 410,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.8,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3800,
    "weight_g": 6310,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN QJ318 belongs to the heavy-duty QJ300 four-point family: the catalogue boundary dimensions read 90 / 190 / 43 mm (bore / OD / width). The designation breaks down as QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 18 give the bore by the standard code table (90 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. On speed, the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 90 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 90 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Do not pair two random QJ318 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 2,800 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The C0 of 410 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 235/410 kN ratings and 14.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ318; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ318?",
        "a": "QJ318 is a four-point contact ball bearing to ISO 15: 90 mm bore, 190 mm outside diameter, 43 mm width (3.543 x 7.48 x 1.693 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 235 kN, C0 410 kN and a 14.8 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min; mass about 6310 g."
      },
      {
        "q": "How is the QJ318 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 18 give the bore by the standard code table (90 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 190 mm OD and 43 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ318 support?",
        "a": "QJ318 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ318?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ318?",
        "a": "The 90/190/43 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 235 kN / C0 410 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ318",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj318",
      "QJ318"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7919",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7919",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 130,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 40.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 2.54,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "speed_oil_rpm": 6600,
    "weight_g": 688,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 95 x 130 x 18 mm, NTN 7919 sits in the extra-light, high-speed 7900 single-row family of the angular-contact programme. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 17.5 mm of radial section, the catalogue still quotes 41.5 kN dynamic capacity for the 95 mm bore. Size selection is usually finished by checking that the C0 of 40.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 40.5 kN really covers the worst static case before substituting it for a 7000.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7919 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 41.5/40.5 kN ratings and 2.54 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7919; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7919?",
        "a": "7919 is a single-row angular contact ball bearing to ISO 15: 95 mm bore, 130 mm outside diameter, 18 mm width (3.74 x 5.118 x 0.709 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 41.5 kN, C0 40.5 kN and a 2.54 kN fatigue load limit Pu; the grease limiting speed is 5,000 r/min and the oil rating 6,600 r/min; mass about 688 g."
      },
      {
        "q": "How is the 7919 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 130 mm OD and 18 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7919 support?",
        "a": "One 7919 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7919?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 5,000 r/min and the oil rating 6,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7919?",
        "a": "The 95/130/18 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 41.5 kN / C0 40.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7919",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7919"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7019-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7019",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 145,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 74,
    "static_load_kN": 67,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.25,
    "limiting_speed_rpm": 4600,
    "max_rpm": 4600,
    "speed_oil_rpm": 6100,
    "weight_g": 1410,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the standard-section 7000 single-row family, 7019 measures 95 mm across the bore, 145 mm over the outer ring and 24 mm across the faces. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 25.0 mm, and the catalogue couples that with C 74 kN / C0 67 kN. Against a deep-groove bearing of the same 95 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 95 mm bore give the working limits. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7019 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "On a 95 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 74/67 kN ratings and 4.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7019; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7019?",
        "a": "7019 is a single-row angular contact ball bearing to ISO 15: 95 mm bore, 145 mm outside diameter, 24 mm width (3.74 x 5.709 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 74 kN, C0 67 kN and a 4.25 kN fatigue load limit Pu; the grease limiting speed is 4,600 r/min and the oil rating 6,100 r/min; mass about 1410 g."
      },
      {
        "q": "How is the 7019 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 145 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7019 support?",
        "a": "One 7019 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7019?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,600 r/min and the oil rating 6,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7019?",
        "a": "The 95/145/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 74 kN / C0 67 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7019",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7019",
      "7019-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7219",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 148,
    "static_load_kN": 118,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.05,
    "limiting_speed_rpm": 4100,
    "max_rpm": 4100,
    "speed_oil_rpm": 5500,
    "weight_g": 2670,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7219 measures 95 mm across the bore, 170 mm over the outer ring and 32 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 148 kN dynamic and 118 kN static for this size and a 8.05 kN fatigue load limit Pu. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 4,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7219 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7219 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 148/118 kN ratings and 8.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7219; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7219?",
        "a": "7219 is a single-row angular contact ball bearing to ISO 15: 95 mm bore, 170 mm outside diameter, 32 mm width (3.74 x 6.693 x 1.26 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 148 kN, C0 118 kN and a 8.05 kN fatigue load limit Pu; the grease limiting speed is 4,100 r/min and the oil rating 5,500 r/min; mass about 2670 g."
      },
      {
        "q": "How is the 7219 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 170 mm OD and 32 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7219 support?",
        "a": "One 7219 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7219?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,100 r/min and the oil rating 5,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7219?",
        "a": "The 95/170/32 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 148 kN / C0 118 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219",
      "7219-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7219B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 134,
    "static_load_kN": 107,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7,
    "limiting_speed_rpm": 3500,
    "max_rpm": 3500,
    "speed_oil_rpm": 4700,
    "weight_g": 2720,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 95 x 170 x 32 mm, NTN 7219B sits in the medium-duty 7200 single-row family of the angular-contact programme. Decoding 7219B: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 19 encodes the 95 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 2720 g, which at this 37.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Size selection is usually finished by checking that the C0 of 107 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 134/107 kN ratings and 7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7219B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7219B?",
        "a": "7219B is a single-row angular contact ball bearing to ISO 15: 95 mm bore, 170 mm outside diameter, 32 mm width (3.74 x 6.693 x 1.26 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 134 kN, C0 107 kN and a 7 kN fatigue load limit Pu; the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min; mass about 2720 g."
      },
      {
        "q": "How is the 7219B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 19 encodes the 95 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 170 mm OD and 32 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7219B support?",
        "a": "One 7219B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7219B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7219B?",
        "a": "The 95/170/32 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 134 kN / C0 107 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219b",
      "7219B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ219",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ219",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 186,
    "static_load_kN": 335,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 12.4,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 3900,
    "weight_g": 3350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, QJ219 appears as a medium-duty QJ200 four-point family bearing of 95 mm bore, 170 mm outside diameter and 32 mm width. Two fields make up the code — QJ2 is the four-point dimension series (medium-duty QJ200 four-point family) and the last two digits 19 give the bore by the standard code table (95 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The radial section height here is 37.5 mm, and the catalogue couples that with C 186 kN / C0 335 kN. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 3,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 186/335 kN ratings and 12.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ219; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ219?",
        "a": "QJ219 is a four-point contact ball bearing to ISO 15: 95 mm bore, 170 mm outside diameter, 32 mm width (3.74 x 6.693 x 1.26 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 186 kN, C0 335 kN and a 12.4 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 3,900 r/min; mass about 3350 g."
      },
      {
        "q": "How is the QJ219 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 19 give the bore by the standard code table (95 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 170 mm OD and 32 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ219 support?",
        "a": "QJ219 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ219?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 3,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ219?",
        "a": "The 95/170/32 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 186 kN / C0 335 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ219",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj219",
      "QJ219"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7319",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 202,
    "static_load_kN": 162,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 10.5,
    "limiting_speed_rpm": 3700,
    "max_rpm": 3700,
    "speed_oil_rpm": 5000,
    "weight_g": 5890,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7319 is the 95 mm bore member of NTN's heavy-duty 7300 single-row family, with a 200 mm outside diameter and 45 mm section width. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 52.5 mm of radial section, the catalogue still quotes 202 kN dynamic capacity for the 95 mm bore. Size selection is usually finished by checking that the C0 of 162 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 162 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 202/162 kN ratings and 10.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7319; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7319?",
        "a": "7319 is a single-row angular contact ball bearing to ISO 15: 95 mm bore, 200 mm outside diameter, 45 mm width (3.74 x 7.874 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 202 kN, C0 162 kN and a 10.5 kN fatigue load limit Pu; the grease limiting speed is 3,700 r/min and the oil rating 5,000 r/min; mass about 5890 g."
      },
      {
        "q": "How is the 7319 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 19 encodes the 95 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 200 mm OD and 45 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7319 support?",
        "a": "One 7319 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7319?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,700 r/min and the oil rating 5,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7319?",
        "a": "The 95/200/45 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 202 kN / C0 162 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319",
      "7319-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7319B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 185,
    "static_load_kN": 149,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 9.6,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4200,
    "weight_g": 6000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7319B belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 95 / 200 / 45 mm (bore / OD / width). Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 19 encodes the 95 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 deg contact angle is the lever that turns the 149 kN static rating into useful one-direction thrust capacity. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Grease quantity matters as much as grade at 3,200 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7319B without re-checking axial float, heat and housing width — the kinematics differ.",
      "A 7319B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A 7319B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 185/149 kN ratings and 9.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7319B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7319B?",
        "a": "7319B is a single-row angular contact ball bearing to ISO 15: 95 mm bore, 200 mm outside diameter, 45 mm width (3.74 x 7.874 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 185 kN, C0 149 kN and a 9.6 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,200 r/min; mass about 6000 g."
      },
      {
        "q": "How is the 7319B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 19 encodes the 95 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 200 mm OD and 45 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7319B support?",
        "a": "One 7319B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7319B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7319B?",
        "a": "The 95/200/45 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 185 kN / C0 149 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319b",
      "7319B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ319",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ319",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 251,
    "static_load_kN": 450,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 16,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3500,
    "weight_g": 7410,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty QJ300 four-point family entry QJ319 carries a 95 mm bore in a 200 mm outside diameter, 45 mm wide envelope. Reading the code: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), the last two digits 19 give the bore by the standard code table (95 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. With C 251 kN and C0 450 kN, each mm of bore carries about 2.64 kN of dynamic rating. The 95/200/45 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 95 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "The 2,700 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "On a 95 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 251/450 kN ratings and 16 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ319; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ319?",
        "a": "QJ319 is a four-point contact ball bearing to ISO 15: 95 mm bore, 200 mm outside diameter, 45 mm width (3.74 x 7.874 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 251 kN, C0 450 kN and a 16 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,500 r/min; mass about 7410 g."
      },
      {
        "q": "How is the QJ319 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 19 give the bore by the standard code table (95 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 200 mm OD and 45 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ319 support?",
        "a": "QJ319 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ319?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ319?",
        "a": "The 95/200/45 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 251 kN / C0 450 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ319",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj319",
      "QJ319"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7920",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7920",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 140,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 53,
    "static_load_kN": 52.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.2,
    "limiting_speed_rpm": 4700,
    "max_rpm": 4700,
    "speed_oil_rpm": 6200,
    "weight_g": 934,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7920 is the 100 mm bore member of NTN's extra-light, high-speed 7900 single-row family, with a 140 mm outside diameter and 20 mm section width. The designation breaks down as 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 20.0 mm, and the catalogue couples that with C 53 kN / C0 52.5 kN. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Grease quantity matters as much as grade at 4,700 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 52.5 kN really covers the worst static case before substituting it for a 7000.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 53/52.5 kN ratings and 3.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7920; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7920?",
        "a": "7920 is a single-row angular contact ball bearing to ISO 15: 100 mm bore, 140 mm outside diameter, 20 mm width (3.937 x 5.512 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 53 kN, C0 52.5 kN and a 3.2 kN fatigue load limit Pu; the grease limiting speed is 4,700 r/min and the oil rating 6,200 r/min; mass about 934 g."
      },
      {
        "q": "How is the 7920 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 140 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7920 support?",
        "a": "One 7920 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7920?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,700 r/min and the oil rating 6,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7920?",
        "a": "The 100/140/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 53 kN / C0 52.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7920",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7920"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7020-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7020",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 150,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 75.5,
    "static_load_kN": 70.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.35,
    "limiting_speed_rpm": 4400,
    "max_rpm": 4400,
    "speed_oil_rpm": 5800,
    "weight_g": 1470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7020 carries a 100 mm bore in a 150 mm outside diameter, 24 mm wide envelope. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 70.5 kN static rating into useful one-direction thrust capacity. Size selection is usually finished by checking that the C0 of 70.5 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 4,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 4,400 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 7020 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 75.5/70.5 kN ratings and 4.35 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7020; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7020?",
        "a": "7020 is a single-row angular contact ball bearing to ISO 15: 100 mm bore, 150 mm outside diameter, 24 mm width (3.937 x 5.906 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 75.5 kN, C0 70.5 kN and a 4.35 kN fatigue load limit Pu; the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min; mass about 1470 g."
      },
      {
        "q": "How is the 7020 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 150 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7020 support?",
        "a": "One 7020 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7020?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,400 r/min and the oil rating 5,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7020?",
        "a": "The 100/150/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 75.5 kN / C0 70.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7020",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7020",
      "7020-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7220",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 159,
    "static_load_kN": 126,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.3,
    "limiting_speed_rpm": 3900,
    "max_rpm": 3900,
    "speed_oil_rpm": 5200,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7220 carries a 100 mm bore in a 180 mm outside diameter, 34 mm wide envelope. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Heat-mounting to 80-90 deg C is the clean route onto a 100 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 126 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "On a 100 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 3,900 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 159/126 kN ratings and 8.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7220; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7220?",
        "a": "7220 is a single-row angular contact ball bearing to ISO 15: 100 mm bore, 180 mm outside diameter, 34 mm width (3.937 x 7.087 x 1.339 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 159 kN, C0 126 kN and a 8.3 kN fatigue load limit Pu; the grease limiting speed is 3,900 r/min and the oil rating 5,200 r/min; mass about 3200 g."
      },
      {
        "q": "How is the 7220 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 180 mm OD and 34 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7220 support?",
        "a": "One 7220 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7220?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,900 r/min and the oil rating 5,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7220?",
        "a": "The 100/180/34 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 159 kN / C0 126 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220",
      "7220-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7220B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 144,
    "static_load_kN": 114,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 7.3,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4500,
    "weight_g": 3260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7220B is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 100 x 180 x 34 mm. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 20 encodes the 100 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 3260 g, which at this 40.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Against a deep-groove bearing of the same 100 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. A 100 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 144/114 kN ratings and 7.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7220B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7220B?",
        "a": "7220B is a single-row angular contact ball bearing to ISO 15: 100 mm bore, 180 mm outside diameter, 34 mm width (3.937 x 7.087 x 1.339 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 144 kN, C0 114 kN and a 7.3 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min; mass about 3260 g."
      },
      {
        "q": "How is the 7220B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 20 encodes the 100 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 180 mm OD and 34 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7220B support?",
        "a": "One 7220B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7220B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7220B?",
        "a": "The 100/180/34 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 144 kN / C0 114 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220b",
      "7220B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ220",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ220",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 200,
    "static_load_kN": 355,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 12.9,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3700,
    "weight_g": 4020,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN QJ220 belongs to the medium-duty QJ200 four-point family: the catalogue boundary dimensions read 100 / 180 / 34 mm (bore / OD / width). The designation breaks down as QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 20 give the bore by the standard code table (100 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The static margin, C0 355 kN versus C 200 kN, is what supports slow oscillating duty and shock without immediate brinelling. For a 100 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "On a 100 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Do not pair two random QJ220 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 200/355 kN ratings and 12.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ220; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ220?",
        "a": "QJ220 is a four-point contact ball bearing to ISO 15: 100 mm bore, 180 mm outside diameter, 34 mm width (3.937 x 7.087 x 1.339 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 200 kN, C0 355 kN and a 12.9 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,700 r/min; mass about 4020 g."
      },
      {
        "q": "How is the QJ220 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 20 give the bore by the standard code table (100 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 180 mm OD and 34 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ220 support?",
        "a": "QJ220 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ220?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,800 r/min and the oil rating 3,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ220?",
        "a": "The 100/180/34 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 200 kN / C0 355 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ220",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj220",
      "QJ220"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7320",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 230,
    "static_load_kN": 193,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 12,
    "limiting_speed_rpm": 3500,
    "max_rpm": 3500,
    "speed_oil_rpm": 4700,
    "weight_g": 7180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 100 x 215 x 47 mm, NTN 7320 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Decoding 7320: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 57.5 mm, and the catalogue couples that with C 230 kN / C0 193 kN. For a 100 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. A 100 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7320 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 230/193 kN ratings and 12 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7320; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7320?",
        "a": "7320 is a single-row angular contact ball bearing to ISO 15: 100 mm bore, 215 mm outside diameter, 47 mm width (3.937 x 8.465 x 1.85 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 230 kN, C0 193 kN and a 12 kN fatigue load limit Pu; the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min; mass about 7180 g."
      },
      {
        "q": "How is the 7320 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 20 encodes the 100 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 215 mm OD and 47 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7320 support?",
        "a": "One 7320 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7320?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7320?",
        "a": "The 100/215/47 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 230 kN / C0 193 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320",
      "7320-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7320B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 211,
    "static_load_kN": 178,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 11.1,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 4000,
    "weight_g": 7320,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7320B is the 100 mm bore member of NTN's heavy-duty 7300 single-row family, with a 215 mm outside diameter and 47 mm section width. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 20 encodes the 100 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). NTN prints 211 kN dynamic and 178 kN static for this size and a 11.1 kN fatigue load limit Pu. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. A 100 mm shaft typically takes a k5/m5 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Do not pair two random 7320B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7320B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 211/178 kN ratings and 11.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7320B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7320B?",
        "a": "7320B is a single-row angular contact ball bearing to ISO 15: 100 mm bore, 215 mm outside diameter, 47 mm width (3.937 x 8.465 x 1.85 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 211 kN, C0 178 kN and a 11.1 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min; mass about 7320 g."
      },
      {
        "q": "How is the 7320B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 20 encodes the 100 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 215 mm OD and 47 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7320B support?",
        "a": "One 7320B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7320B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7320B?",
        "a": "The 100/215/47 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 211 kN / C0 178 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320b",
      "7320B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ320",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ320",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 300,
    "static_load_kN": 585,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 20,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3400,
    "weight_g": 9140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 100 x 215 x 47 mm, NTN QJ320 sits in the heavy-duty QJ300 four-point family of the angular-contact programme. NTN builds the number from QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), then the last two digits 20 give the bore by the standard code table (100 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. At roughly 57.5 mm of radial section, the catalogue still quotes 300 kN dynamic capacity for the 100 mm bore. Size selection is usually finished by checking that the C0 of 585 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 100 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "On a 100 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 300/585 kN ratings and 20 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ320; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ320?",
        "a": "QJ320 is a four-point contact ball bearing to ISO 15: 100 mm bore, 215 mm outside diameter, 47 mm width (3.937 x 8.465 x 1.85 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 300 kN, C0 585 kN and a 20 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min; mass about 9140 g."
      },
      {
        "q": "How is the QJ320 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 20 give the bore by the standard code table (100 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 215 mm OD and 47 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ320 support?",
        "a": "QJ320 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ320?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ320?",
        "a": "The 100/215/47 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 300 kN / C0 585 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ320",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj320",
      "QJ320"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7921",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7921",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 145,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 54,
    "static_load_kN": 54.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.25,
    "limiting_speed_rpm": 4400,
    "max_rpm": 4400,
    "speed_oil_rpm": 5900,
    "weight_g": 972,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the extra-light, high-speed 7900 single-row family, 7921 measures 105 mm across the bore, 145 mm over the outer ring and 20 mm across the faces. Reading the code: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 54.5 kN static rating into useful one-direction thrust capacity. The 105/145/20 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 54.5 kN really covers the worst static case before substituting it for a 7000.",
      "A 7921 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 54.5 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A 7921 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 54/54.5 kN ratings and 3.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7921; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7921?",
        "a": "7921 is a single-row angular contact ball bearing to ISO 15: 105 mm bore, 145 mm outside diameter, 20 mm width (4.134 x 5.709 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 54 kN, C0 54.5 kN and a 3.25 kN fatigue load limit Pu; the grease limiting speed is 4,400 r/min and the oil rating 5,900 r/min; mass about 972 g."
      },
      {
        "q": "How is the 7921 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 145 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7921 support?",
        "a": "One 7921 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7921?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,400 r/min and the oil rating 5,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7921?",
        "a": "The 105/145/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 54 kN / C0 54.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7921",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7921"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7021-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7021",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 160,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 88.5,
    "static_load_kN": 81.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 4.95,
    "limiting_speed_rpm": 4100,
    "max_rpm": 4100,
    "speed_oil_rpm": 5500,
    "weight_g": 1860,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7021 belongs to the standard-section 7000 single-row family: the catalogue boundary dimensions read 105 / 160 / 26 mm (bore / OD / width). Decoding 7021: 70 is the single-row dimension series (standard-section 7000 single-row family), with 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 88.5 kN and C0 81.5 kN, each mm of bore carries about 0.84 kN of dynamic rating. The 105/160/26 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Heat-mounting to 80-90 deg C is the clean route onto a 105 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7021 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "On a 105 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 88.5/81.5 kN ratings and 4.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7021; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7021?",
        "a": "7021 is a single-row angular contact ball bearing to ISO 15: 105 mm bore, 160 mm outside diameter, 26 mm width (4.134 x 6.299 x 1.024 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 88.5 kN, C0 81.5 kN and a 4.95 kN fatigue load limit Pu; the grease limiting speed is 4,100 r/min and the oil rating 5,500 r/min; mass about 1860 g."
      },
      {
        "q": "How is the 7021 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 160 mm OD and 26 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7021 support?",
        "a": "One 7021 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7021?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,100 r/min and the oil rating 5,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7021?",
        "a": "The 105/160/26 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 88.5 kN / C0 81.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7021",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7021",
      "7021-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7221-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7221",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 173,
    "static_load_kN": 142,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 9.1,
    "limiting_speed_rpm": 3700,
    "max_rpm": 3700,
    "speed_oil_rpm": 5000,
    "weight_g": 3790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 105 x 190 x 36 mm, NTN 7221 sits in the medium-duty 7200 single-row family of the angular-contact programme. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 3790 g, which at this 42.5 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Against a deep-groove bearing of the same 105 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Heat-mounting to 80-90 deg C is the clean route onto a 105 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 3,700 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 7221 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 173/142 kN ratings and 9.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7221; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7221?",
        "a": "7221 is a single-row angular contact ball bearing to ISO 15: 105 mm bore, 190 mm outside diameter, 36 mm width (4.134 x 7.48 x 1.417 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 173 kN, C0 142 kN and a 9.1 kN fatigue load limit Pu; the grease limiting speed is 3,700 r/min and the oil rating 5,000 r/min; mass about 3790 g."
      },
      {
        "q": "How is the 7221 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 190 mm OD and 36 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7221 support?",
        "a": "One 7221 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7221?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,700 r/min and the oil rating 5,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7221?",
        "a": "The 105/190/36 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 173 kN / C0 142 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7221",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×190×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7221-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×190×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7221-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×190×36 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7221",
      "7221-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7221B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7221B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 157,
    "static_load_kN": 129,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.05,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4300,
    "weight_g": 3870,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7221B carries a 105 mm bore in a 190 mm outside diameter, 36 mm wide envelope. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 21 encodes the 105 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 deg contact angle is the lever that turns the 129 kN static rating into useful one-direction thrust capacity. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7221B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 3,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 7221B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 157/129 kN ratings and 8.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7221B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7221B?",
        "a": "7221B is a single-row angular contact ball bearing to ISO 15: 105 mm bore, 190 mm outside diameter, 36 mm width (4.134 x 7.48 x 1.417 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 157 kN, C0 129 kN and a 8.05 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min; mass about 3870 g."
      },
      {
        "q": "How is the 7221B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 21 encodes the 105 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 190 mm OD and 36 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7221B support?",
        "a": "One 7221B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7221B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7221B?",
        "a": "The 105/190/36 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 157 kN / C0 129 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7221B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7221b",
      "7221B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ221",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ221",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 218,
    "static_load_kN": 400,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.2,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3600,
    "weight_g": 4750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty QJ200 four-point family entry QJ221 carries a 105 mm bore in a 190 mm outside diameter, 36 mm wide envelope. Reading the code: QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), the last two digits 21 give the bore by the standard code table (105 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The oil rating of 3,600 r/min sits 900 r/min above the 2,700 r/min grease figure — a 1.33x step that says how much headroom oil cooling buys. Against a deep-groove bearing of the same 105 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 105 mm bore give the working limits. ",
    "applications": [
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ221 without re-checking axial float, heat and housing width — the kinematics differ.",
      "On a 105 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 218/400 kN ratings and 14.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ221; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ221?",
        "a": "QJ221 is a four-point contact ball bearing to ISO 15: 105 mm bore, 190 mm outside diameter, 36 mm width (4.134 x 7.48 x 1.417 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 218 kN, C0 400 kN and a 14.2 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min; mass about 4750 g."
      },
      {
        "q": "How is the QJ221 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 21 give the bore by the standard code table (105 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 190 mm OD and 36 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ221 support?",
        "a": "QJ221 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ221?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ221?",
        "a": "The 105/190/36 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 218 kN / C0 400 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ221",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj221",
      "QJ221"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7321-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7321",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 244,
    "static_load_kN": 210,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 12.8,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "speed_oil_rpm": 4500,
    "weight_g": 8200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7321 carries a 105 mm bore in a 225 mm outside diameter, 49 mm wide envelope. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 105 mm bore give the working limits. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 210 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The C0 of 210 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 244/210 kN ratings and 12.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7321; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7321?",
        "a": "7321 is a single-row angular contact ball bearing to ISO 15: 105 mm bore, 225 mm outside diameter, 49 mm width (4.134 x 8.858 x 1.929 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 244 kN, C0 210 kN and a 12.8 kN fatigue load limit Pu; the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min; mass about 8200 g."
      },
      {
        "q": "How is the 7321 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 21 encodes the 105 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 225 mm OD and 49 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7321 support?",
        "a": "One 7321 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7321?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,400 r/min and the oil rating 4,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7321?",
        "a": "The 105/225/49 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 244 kN / C0 210 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7321",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7321-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7321-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7321-DECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7321",
      "7321-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7321B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7321B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 224,
    "static_load_kN": 194,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 11.8,
    "limiting_speed_rpm": 2900,
    "max_rpm": 2900,
    "speed_oil_rpm": 3800,
    "weight_g": 8360,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7321B appears as a heavy-duty 7300 single-row family bearing of 105 mm bore, 225 mm outside diameter and 49 mm width. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 21 encodes the 105 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 8360 g, which at this 60.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 224/194 kN ratings and 11.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7321B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7321B?",
        "a": "7321B is a single-row angular contact ball bearing to ISO 15: 105 mm bore, 225 mm outside diameter, 49 mm width (4.134 x 8.858 x 1.929 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 224 kN, C0 194 kN and a 11.8 kN fatigue load limit Pu; the grease limiting speed is 2,900 r/min and the oil rating 3,800 r/min; mass about 8360 g."
      },
      {
        "q": "How is the 7321B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 21 encodes the 105 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 225 mm OD and 49 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7321B support?",
        "a": "One 7321B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7321B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,900 r/min and the oil rating 3,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7321B?",
        "a": "The 105/225/49 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 224 kN / C0 194 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7321B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7321b",
      "7321B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ321",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ321",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 305,
    "static_load_kN": 585,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 19.6,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3200,
    "weight_g": 10400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ321 is the 105 mm bore member of NTN's heavy-duty QJ300 four-point family, with a 225 mm outside diameter and 49 mm section width. The designation breaks down as QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 21 give the bore by the standard code table (105 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. NTN prints 305 kN dynamic and 585 kN static for this size and a 19.6 kN fatigue load limit Pu. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 105 mm bore give the working limits. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 105 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ321 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 305/585 kN ratings and 19.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ321; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ321?",
        "a": "QJ321 is a four-point contact ball bearing to ISO 15: 105 mm bore, 225 mm outside diameter, 49 mm width (4.134 x 8.858 x 1.929 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 305 kN, C0 585 kN and a 19.6 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,200 r/min; mass about 10400 g."
      },
      {
        "q": "How is the QJ321 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 21 give the bore by the standard code table (105 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 225 mm OD and 49 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ321 support?",
        "a": "QJ321 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ321?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,400 r/min and the oil rating 3,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ321?",
        "a": "The 105/225/49 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 305 kN / C0 585 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ321",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj321",
      "QJ321"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7922",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7922",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 150,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 54.5,
    "static_load_kN": 56,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.25,
    "limiting_speed_rpm": 4200,
    "max_rpm": 4200,
    "speed_oil_rpm": 5700,
    "weight_g": 1010,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7922 is an NTN single-row angular contact ball bearing: extra-light, high-speed 7900 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 110 x 150 x 20 mm. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 4,200 r/min and the oil rating 5,700 r/min. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. A 110 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts",
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 56 kN really covers the worst static case before substituting it for a 7000.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The C0 of 56 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 54.5/56 kN ratings and 3.25 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7922; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7922?",
        "a": "7922 is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 150 mm outside diameter, 20 mm width (4.331 x 5.906 x 0.787 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 54.5 kN, C0 56 kN and a 3.25 kN fatigue load limit Pu; the grease limiting speed is 4,200 r/min and the oil rating 5,700 r/min; mass about 1010 g."
      },
      {
        "q": "How is the 7922 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 150 mm OD and 20 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7922 support?",
        "a": "One 7922 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7922?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 4,200 r/min and the oil rating 5,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7922?",
        "a": "The 110/150/20 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 54.5 kN / C0 56 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7922",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7922"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7022-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7022",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 170,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 102,
    "static_load_kN": 93,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.5,
    "limiting_speed_rpm": 3900,
    "max_rpm": 3900,
    "speed_oil_rpm": 5300,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7022 carries a 110 mm bore in a 170 mm outside diameter, 28 mm wide envelope. The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 93 kN versus C 102 kN, is what supports slow oscillating duty and shock without immediate brinelling. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 110 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions",
      "marine auxiliary and winch gearbox shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7022 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random 7022 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 102/93 kN ratings and 5.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7022; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7022?",
        "a": "7022 is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 170 mm outside diameter, 28 mm width (4.331 x 6.693 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 102 kN, C0 93 kN and a 5.5 kN fatigue load limit Pu; the grease limiting speed is 3,900 r/min and the oil rating 5,300 r/min; mass about 2300 g."
      },
      {
        "q": "How is the 7022 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 170 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7022 support?",
        "a": "One 7022 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7022?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,900 r/min and the oil rating 5,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7022?",
        "a": "The 110/170/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 102 kN / C0 93 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7022",
        "equiv_brand": "GENERIC-ISO",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7022",
      "7022-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7222",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 188,
    "static_load_kN": 158,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 9.95,
    "limiting_speed_rpm": 3500,
    "max_rpm": 3500,
    "speed_oil_rpm": 4700,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7222 carries a 110 mm bore in a 200 mm outside diameter, 38 mm wide envelope. Decoding 7222: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 4,700 r/min sits 1,200 r/min above the 3,500 r/min grease figure — a 1.34x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 110 mm bore give the working limits. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 188/158 kN ratings and 9.95 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7222; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7222?",
        "a": "7222 is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 200 mm outside diameter, 38 mm width (4.331 x 7.874 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 188 kN, C0 158 kN and a 9.95 kN fatigue load limit Pu; the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min; mass about 4450 g."
      },
      {
        "q": "How is the 7222 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 200 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7222 support?",
        "a": "One 7222 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7222?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,500 r/min and the oil rating 4,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7222?",
        "a": "The 110/200/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 188 kN / C0 158 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222",
      "7222-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7222B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 170,
    "static_load_kN": 144,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 8.8,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 4000,
    "weight_g": 4540,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7222B measures 110 mm across the bore, 200 mm over the outer ring and 38 mm across the faces. Decoding 7222B: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 22 encodes the 110 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). With C 170 kN and C0 144 kN, each mm of bore carries about 1.55 kN of dynamic rating. For a 110 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. Grease quantity matters as much as grade at 3,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A 7222B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "On a 110 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 170/144 kN ratings and 8.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7222B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7222B?",
        "a": "7222B is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 200 mm outside diameter, 38 mm width (4.331 x 7.874 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 170 kN, C0 144 kN and a 8.8 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min; mass about 4540 g."
      },
      {
        "q": "How is the 7222B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 22 encodes the 110 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 200 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7222B support?",
        "a": "One 7222B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7222B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7222B?",
        "a": "The 110/200/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 170 kN / C0 144 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222b",
      "7222B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ222",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ222",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 236,
    "static_load_kN": 450,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 15.5,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3400,
    "weight_g": 5620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 110 x 200 x 38 mm, NTN QJ222 sits in the medium-duty QJ200 four-point family of the angular-contact programme. Two fields make up the code — QJ2 is the four-point dimension series (medium-duty QJ200 four-point family) and the last two digits 22 give the bore by the standard code table (110 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Catalogue dynamic rating C is 236 kN against C0 450 kN — a C0/C ratio of 1.91 that is typical of an angular-contact contact ellipse. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 110 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "The C0 of 450 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 236/450 kN ratings and 15.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ222; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ222?",
        "a": "QJ222 is a four-point contact ball bearing to ISO 15: 110 mm bore, 200 mm outside diameter, 38 mm width (4.331 x 7.874 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 236 kN, C0 450 kN and a 15.5 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min; mass about 5620 g."
      },
      {
        "q": "How is the QJ222 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 22 give the bore by the standard code table (110 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 200 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ222 support?",
        "a": "QJ222 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ222?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ222?",
        "a": "The 110/200/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 236 kN / C0 450 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ222",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj222",
      "QJ222"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322-NTN",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7322",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 273,
    "static_load_kN": 246,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 14.5,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4300,
    "weight_g": 9600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 110 x 240 x 50 mm, NTN 7322 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 273 kN and C0 246 kN, each mm of bore carries about 2.48 kN of dynamic rating. Against a deep-groove bearing of the same 110 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 110 mm bore give the working limits. ",
    "applications": [
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts",
      "mining conveyor head-shaft positions"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 3,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 7322 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "On a 110 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 273/246 kN ratings and 14.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7322; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7322?",
        "a": "7322 is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 240 mm outside diameter, 50 mm width (4.331 x 9.449 x 1.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 273 kN, C0 246 kN and a 14.5 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min; mass about 9600 g."
      },
      {
        "q": "How is the 7322 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 22 encodes the 110 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 240 mm OD and 50 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7322 support?",
        "a": "One 7322 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7322?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7322?",
        "a": "The 110/240/50 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 273 kN / C0 246 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322",
      "7322-NTN"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7322B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 250,
    "static_load_kN": 226,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 13.3,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3700,
    "weight_g": 9800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 110 x 240 x 50 mm, NTN 7322B sits in the heavy-duty 7300 single-row family of the angular-contact programme. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 22 encodes the 110 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 deg contact angle is the lever that turns the 226 kN static rating into useful one-direction thrust capacity. The 110/240/50 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Grease quantity matters as much as grade at 2,700 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives",
      "extruder and mixer gearbox output shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "On a 110 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 7322B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 250/226 kN ratings and 13.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7322B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7322B?",
        "a": "7322B is a single-row angular contact ball bearing to ISO 15: 110 mm bore, 240 mm outside diameter, 50 mm width (4.331 x 9.449 x 1.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 250 kN, C0 226 kN and a 13.3 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,700 r/min; mass about 9800 g."
      },
      {
        "q": "How is the 7322B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 22 encodes the 110 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 240 mm OD and 50 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7322B support?",
        "a": "One 7322B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7322B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7322B?",
        "a": "The 110/240/50 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 250 kN / C0 226 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322b",
      "7322B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ322",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ322",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 340,
    "static_load_kN": 680,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 22.1,
    "limiting_speed_rpm": 2300,
    "max_rpm": 2300,
    "speed_oil_rpm": 3100,
    "weight_g": 12000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty QJ300 four-point family, QJ322 measures 110 mm across the bore, 240 mm over the outer ring and 50 mm across the faces. Reading the code: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), the last two digits 22 give the bore by the standard code table (110 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. For a 110 mm shaft with combined load, the practical shortlist is this series, its neighbouring dimension series, and — where thrust reverses — a back-to-back pair rather than a single row. Heat-mounting to 80-90 deg C is the clean route onto a 110 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "rolling-mill and metalworking drive shafts",
      "large pump, fan and compressor rotor shafts",
      "crane and hoist gearbox shafts",
      "paper-machine roll and calendar drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "Bearings of 110 mm bore arrive heavy enough that handling damage (dents from slings, tilting on the shaft) is a real failure precursor — use proper lifting and heating kit.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ322 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 2,300 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 340/680 kN ratings and 22.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ322; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ322?",
        "a": "QJ322 is a four-point contact ball bearing to ISO 15: 110 mm bore, 240 mm outside diameter, 50 mm width (4.331 x 9.449 x 1.969 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 340 kN, C0 680 kN and a 22.1 kN fatigue load limit Pu; the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min; mass about 12000 g."
      },
      {
        "q": "How is the QJ322 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 22 give the bore by the standard code table (110 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 240 mm OD and 50 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ322 support?",
        "a": "QJ322 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ322?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ322?",
        "a": "The 110/240/50 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 340 kN / C0 680 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ322",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj322",
      "QJ322"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7924",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7924",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 165,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 67.5,
    "static_load_kN": 69.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 3.9,
    "limiting_speed_rpm": 3900,
    "max_rpm": 3900,
    "speed_oil_rpm": 5200,
    "weight_g": 1660,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7924 belongs to the extra-light, high-speed 7900 single-row family: the catalogue boundary dimensions read 120 / 165 / 22 mm (bore / OD / width). NTN builds the number from 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), then 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 69.5 kN versus C 67.5 kN, is what supports slow oscillating duty and shock without immediate brinelling. Choose the extra-light, high-speed 7900 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 120 mm bore give the working limits. ",
    "applications": [
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 69.5 kN really covers the worst static case before substituting it for a 7000.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random 7924 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Do not pair two random 7924 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 67.5/69.5 kN ratings and 3.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7924; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7924?",
        "a": "7924 is a single-row angular contact ball bearing to ISO 15: 120 mm bore, 165 mm outside diameter, 22 mm width (4.724 x 6.496 x 0.866 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 67.5 kN, C0 69.5 kN and a 3.9 kN fatigue load limit Pu; the grease limiting speed is 3,900 r/min and the oil rating 5,200 r/min; mass about 1660 g."
      },
      {
        "q": "How is the 7924 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 165 mm OD and 22 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7924 support?",
        "a": "One 7924 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7924?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,900 r/min and the oil rating 5,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7924?",
        "a": "The 120/165/22 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 67.5 kN / C0 69.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7924",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=131",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7924"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7024",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7024",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 180,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 104,
    "static_load_kN": 98.5,
    "cage_type": "steel_stamped_J",
    "fatigue_load_limit_kN": 5.55,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "speed_oil_rpm": 4800,
    "weight_g": 2470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7024 carries a 120 mm bore in a 180 mm outside diameter, 28 mm wide envelope. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 104 kN against C0 98.5 kN — a C0/C ratio of 0.95 that is typical of an angular-contact contact ellipse. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 120 mm bore give the working limits. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 120 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 104/98.5 kN ratings and 5.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7024; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7024?",
        "a": "7024 is a single-row angular contact ball bearing to ISO 15: 120 mm bore, 180 mm outside diameter, 28 mm width (4.724 x 7.087 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 104 kN, C0 98.5 kN and a 5.55 kN fatigue load limit Pu; the grease limiting speed is 3,600 r/min and the oil rating 4,800 r/min; mass about 2470 g."
      },
      {
        "q": "How is the 7024 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 180 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7024 support?",
        "a": "One 7024 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7024?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,600 r/min and the oil rating 4,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7024?",
        "a": "The 120/180/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 104 kN / C0 98.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7024-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×180×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7024"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7224",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7224",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 202,
    "static_load_kN": 177,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 10.7,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "speed_oil_rpm": 4300,
    "weight_g": 6260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7224 is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 120 x 215 x 40 mm. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 4,300 r/min sits 1,100 r/min above the 3,200 r/min grease figure — a 1.34x step that says how much headroom oil cooling buys. The 120/215/40 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 3,200 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 7224 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,200 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 202/177 kN ratings and 10.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7224; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7224?",
        "a": "7224 is a single-row angular contact ball bearing to ISO 15: 120 mm bore, 215 mm outside diameter, 40 mm width (4.724 x 8.465 x 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 202 kN, C0 177 kN and a 10.7 kN fatigue load limit Pu; the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min; mass about 6260 g."
      },
      {
        "q": "How is the 7224 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 215 mm OD and 40 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7224 support?",
        "a": "One 7224 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7224?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,200 r/min and the oil rating 4,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7224?",
        "a": "The 120/215/40 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 202 kN / C0 177 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7224-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7224-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7224"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7224B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7224B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 183,
    "static_load_kN": 162,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 9.4,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3700,
    "weight_g": 6260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7224B is the 120 mm bore member of NTN's medium-duty 7200 single-row family, with a 215 mm outside diameter and 40 mm section width. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 24 encodes the 120 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). At roughly 47.5 mm of radial section, the catalogue still quotes 183 kN dynamic capacity for the 120 mm bore. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 120 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 162 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 183/162 kN ratings and 9.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7224B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7224B?",
        "a": "7224B is a single-row angular contact ball bearing to ISO 15: 120 mm bore, 215 mm outside diameter, 40 mm width (4.724 x 8.465 x 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 183 kN, C0 162 kN and a 9.4 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,700 r/min; mass about 6260 g."
      },
      {
        "q": "How is the 7224B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 24 encodes the 120 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 215 mm OD and 40 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7224B support?",
        "a": "One 7224B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7224B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,800 r/min and the oil rating 3,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7224B?",
        "a": "The 120/215/40 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 183 kN / C0 162 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7224B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7224b",
      "7224B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ224",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ224",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 266,
    "static_load_kN": 540,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 17.7,
    "limiting_speed_rpm": 2300,
    "max_rpm": 2300,
    "speed_oil_rpm": 3100,
    "weight_g": 6750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty QJ200 four-point family, QJ224 measures 120 mm across the bore, 215 mm over the outer ring and 40 mm across the faces. NTN builds the number from QJ2 is the four-point dimension series (medium-duty QJ200 four-point family), then the last two digits 24 give the bore by the standard code table (120 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. NTN prints 266 kN dynamic and 540 kN static for this size and a 17.7 kN fatigue load limit Pu. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 2,300 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "A QJ224 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single QJ224 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 266/540 kN ratings and 17.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ224; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ224?",
        "a": "QJ224 is a four-point contact ball bearing to ISO 15: 120 mm bore, 215 mm outside diameter, 40 mm width (4.724 x 8.465 x 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 266 kN, C0 540 kN and a 17.7 kN fatigue load limit Pu; the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min; mass about 6750 g."
      },
      {
        "q": "How is the QJ224 designation structured?",
        "a": "QJ2 is the four-point dimension series (medium-duty QJ200 four-point family); the last two digits 24 give the bore by the standard code table (120 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 215 mm OD and 40 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ224 support?",
        "a": "QJ224 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ224?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ224?",
        "a": "The 120/215/40 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 266 kN / C0 540 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ224",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj224",
      "QJ224"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7324",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7324",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 260,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 273,
    "static_load_kN": 252,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.3,
    "limiting_speed_rpm": 2900,
    "max_rpm": 2900,
    "speed_oil_rpm": 3900,
    "weight_g": 14700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7324 belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 120 / 260 / 55 mm (bore / OD / width). NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 273 kN dynamic and 252 kN static for this size and a 14.3 kN fatigue load limit Pu. Against a deep-groove bearing of the same 120 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7324 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 2,900 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7324 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 273/252 kN ratings and 14.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7324; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7324?",
        "a": "7324 is a single-row angular contact ball bearing to ISO 15: 120 mm bore, 260 mm outside diameter, 55 mm width (4.724 x 10.236 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 273 kN, C0 252 kN and a 14.3 kN fatigue load limit Pu; the grease limiting speed is 2,900 r/min and the oil rating 3,900 r/min; mass about 14700 g."
      },
      {
        "q": "How is the 7324 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 24 encodes the 120 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 260 mm OD and 55 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7324 support?",
        "a": "One 7324 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7324?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,900 r/min and the oil rating 3,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7324?",
        "a": "The 120/260/55 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 273 kN / C0 252 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7324-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×260×55 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7324"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7324B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7324B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 260,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 249,
    "static_load_kN": 231,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 13.1,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3300,
    "weight_g": 14700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7324B carries a 120 mm bore in a 260 mm outside diameter, 55 mm wide envelope. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 24 encodes the 120 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The oil rating of 3,300 r/min sits 800 r/min above the 2,500 r/min grease figure — a 1.32x step that says how much headroom oil cooling buys. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Heat-mounting to 80-90 deg C is the clean route onto a 120 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 249/231 kN ratings and 13.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7324B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7324B?",
        "a": "7324B is a single-row angular contact ball bearing to ISO 15: 120 mm bore, 260 mm outside diameter, 55 mm width (4.724 x 10.236 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 249 kN, C0 231 kN and a 13.1 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min; mass about 14700 g."
      },
      {
        "q": "How is the 7324B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 24 encodes the 120 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 260 mm OD and 55 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7324B support?",
        "a": "One 7324B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7324B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7324B?",
        "a": "The 120/260/55 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 249 kN / C0 231 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7324B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7324b",
      "7324B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ324",
    "brand": "NTN",
    "manufacturer_designation": "NTN QJ324",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 260,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 360,
    "static_load_kN": 765,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 23.8,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 2800,
    "weight_g": 15900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, QJ324 appears as a heavy-duty QJ300 four-point family bearing of 120 mm bore, 260 mm outside diameter and 55 mm width. Decoding QJ324: QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family), with the last two digits 24 give the bore by the standard code table (120 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The radial section height here is 70.0 mm, and the catalogue couples that with C 360 kN / C0 765 kN. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Grease quantity matters as much as grade at 2,100 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 120 mm bore bearing forgives nothing in a poorly machined housing.",
      "The QJ split inner ring must be clamped by the shaft nut/shoulder on both halves — assembling it against a single small shoulder leaves one half-ring free to walk.",
      "Do not pair two random QJ324 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The C0 of 765 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 360/765 kN ratings and 23.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for QJ324; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN QJ324?",
        "a": "QJ324 is a four-point contact ball bearing to ISO 15: 120 mm bore, 260 mm outside diameter, 55 mm width (4.724 x 10.236 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 360 kN, C0 765 kN and a 23.8 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min; mass about 15900 g."
      },
      {
        "q": "How is the QJ324 designation structured?",
        "a": "QJ3 is the four-point dimension series (heavy-duty QJ300 four-point family); the last two digits 24 give the bore by the standard code table (120 mm); there is no suffix — the split inner ring and 35 deg contact angle are inherent to the QJ design. The 260 mm OD and 55 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does QJ324 support?",
        "a": "QJ324 is a four-point contact bearing: the split inner ring lets each ball touch the raceways at two points, so one bearing locates the shaft in both axial directions at its 35 deg contact angle. It is normally mounted with slight radial clearance against the housing as the axial-locating member."
      },
      {
        "q": "What lubrication speeds does NTN print for QJ324?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for QJ324?",
        "a": "The 120/260/55 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 360 kN / C0 765 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ324",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=134",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "qj324",
      "QJ324"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7926",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7926",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 180,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 83,
    "static_load_kN": 87.5,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 4.65,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "speed_oil_rpm": 4700,
    "weight_g": 1820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 130 x 180 x 24 mm, NTN 7926 sits in the extra-light, high-speed 7900 single-row family of the angular-contact programme. Reading the code: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 83 kN against C0 87.5 kN — a C0/C ratio of 1.05 that is typical of an angular-contact contact ellipse. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 130 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 87.5 kN really covers the worst static case before substituting it for a 7000.",
      "Do not pair two random 7926 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 3,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 83/87.5 kN ratings and 4.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7926; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7926?",
        "a": "7926 is a single-row angular contact ball bearing to ISO 15: 130 mm bore, 180 mm outside diameter, 24 mm width (5.118 x 7.087 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 83 kN, C0 87.5 kN and a 4.65 kN fatigue load limit Pu; the grease limiting speed is 3,600 r/min and the oil rating 4,700 r/min; mass about 1820 g."
      },
      {
        "q": "How is the 7926 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 180 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7926 support?",
        "a": "One 7926 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7926?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,600 r/min and the oil rating 4,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7926?",
        "a": "The 130/180/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 83 kN / C0 87.5 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7926",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7926"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7026",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7026",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 200,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 130,
    "static_load_kN": 125,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 6.75,
    "limiting_speed_rpm": 3300,
    "max_rpm": 3300,
    "speed_oil_rpm": 4400,
    "weight_g": 3730,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7026 is the 130 mm bore member of NTN's standard-section 7000 single-row family, with a 200 mm outside diameter and 33 mm section width. NTN builds the number from 70 is the single-row dimension series (standard-section 7000 single-row family), then 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 130 kN dynamic and 125 kN static for this size and a 6.75 kN fatigue load limit Pu. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 130 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 125 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Do not pair two random 7026 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7026 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 130/125 kN ratings and 6.75 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7026; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7026?",
        "a": "7026 is a single-row angular contact ball bearing to ISO 15: 130 mm bore, 200 mm outside diameter, 33 mm width (5.118 x 7.874 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 130 kN, C0 125 kN and a 6.75 kN fatigue load limit Pu; the grease limiting speed is 3,300 r/min and the oil rating 4,400 r/min; mass about 3730 g."
      },
      {
        "q": "How is the 7026 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 200 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7026 support?",
        "a": "One 7026 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7026?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,300 r/min and the oil rating 4,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7026?",
        "a": "The 130/200/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 130 kN / C0 125 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7026",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7026"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7226",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7226",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 217,
    "static_load_kN": 198,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 11.5,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "speed_oil_rpm": 4000,
    "weight_g": 7150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7226 belongs to the medium-duty 7200 single-row family: the catalogue boundary dimensions read 130 / 230 / 40 mm (bore / OD / width). Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 50.0 mm of radial section, the catalogue still quotes 217 kN dynamic capacity for the 130 mm bore. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 130 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7226 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 217/198 kN ratings and 11.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7226; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7226?",
        "a": "7226 is a single-row angular contact ball bearing to ISO 15: 130 mm bore, 230 mm outside diameter, 40 mm width (5.118 x 9.055 x 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 217 kN, C0 198 kN and a 11.5 kN fatigue load limit Pu; the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min; mass about 7150 g."
      },
      {
        "q": "How is the 7226 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 230 mm OD and 40 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7226 support?",
        "a": "One 7226 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7226?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,000 r/min and the oil rating 4,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7226?",
        "a": "The 130/230/40 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 217 kN / C0 198 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7226-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7226-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7226"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7226B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7226B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 196,
    "static_load_kN": 180,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 10,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3400,
    "weight_g": 7150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 130 x 230 x 40 mm, NTN 7226B sits in the medium-duty 7200 single-row family of the angular-contact programme. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 26 encodes the 130 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The radial section height here is 50.0 mm, and the catalogue couples that with C 196 kN / C0 180 kN. Size selection is usually finished by checking that the C0 of 180 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 130 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The 2,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The C0 of 180 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 196/180 kN ratings and 10 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7226B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7226B?",
        "a": "7226B is a single-row angular contact ball bearing to ISO 15: 130 mm bore, 230 mm outside diameter, 40 mm width (5.118 x 9.055 x 1.575 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 196 kN, C0 180 kN and a 10 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min; mass about 7150 g."
      },
      {
        "q": "How is the 7226B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 26 encodes the 130 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 230 mm OD and 40 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7226B support?",
        "a": "One 7226B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7226B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7226B?",
        "a": "The 130/230/40 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 196 kN / C0 180 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7226B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7226b",
      "7226B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7326",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7326",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 280,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 305,
    "static_load_kN": 293,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 16,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3600,
    "weight_g": 17600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 130 x 280 x 58 mm, NTN 7326 sits in the heavy-duty 7300 single-row family of the angular-contact programme. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 17600 g, which at this 75.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. The 130/280/58 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 130 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 130 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 305/293 kN ratings and 16 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7326; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7326?",
        "a": "7326 is a single-row angular contact ball bearing to ISO 15: 130 mm bore, 280 mm outside diameter, 58 mm width (5.118 x 11.024 x 2.283 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 305 kN, C0 293 kN and a 16 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min; mass about 17600 g."
      },
      {
        "q": "How is the 7326 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 26 encodes the 130 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 280 mm OD and 58 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7326 support?",
        "a": "One 7326 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7326?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7326?",
        "a": "The 130/280/58 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 305 kN / C0 293 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7326-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×280×58 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7326-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×280×58 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7326"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7326B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7326B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 280,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 277,
    "static_load_kN": 268,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.7,
    "limiting_speed_rpm": 2300,
    "max_rpm": 2300,
    "speed_oil_rpm": 3100,
    "weight_g": 17600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7326B belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 130 / 280 / 58 mm (bore / OD / width). NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 26 encodes the 130 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Against a deep-groove bearing of the same 130 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 130 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 2,300 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 277/268 kN ratings and 14.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7326B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7326B?",
        "a": "7326B is a single-row angular contact ball bearing to ISO 15: 130 mm bore, 280 mm outside diameter, 58 mm width (5.118 x 11.024 x 2.283 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 277 kN, C0 268 kN and a 14.7 kN fatigue load limit Pu; the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min; mass about 17600 g."
      },
      {
        "q": "How is the 7326B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 26 encodes the 130 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 280 mm OD and 58 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7326B support?",
        "a": "One 7326B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7326B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7326B?",
        "a": "The 130/280/58 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 277 kN / C0 268 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7326B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7326b",
      "7326B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7928",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7928",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 190,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 83.5,
    "static_load_kN": 90,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 4.65,
    "limiting_speed_rpm": 3300,
    "max_rpm": 3300,
    "speed_oil_rpm": 4400,
    "weight_g": 1940,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the extra-light, high-speed 7900 single-row family, 7928 measures 140 mm across the bore, 190 mm over the outer ring and 24 mm across the faces. Decoding 7928: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 83.5 kN dynamic and 90 kN static for this size and a 4.65 kN fatigue load limit Pu. Against a deep-groove bearing of the same 140 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 140 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 90 kN really covers the worst static case before substituting it for a 7000.",
      "On a 140 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 140 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7928 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 83.5/90 kN ratings and 4.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7928; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7928?",
        "a": "7928 is a single-row angular contact ball bearing to ISO 15: 140 mm bore, 190 mm outside diameter, 24 mm width (5.512 x 7.48 x 0.945 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 83.5 kN, C0 90 kN and a 4.65 kN fatigue load limit Pu; the grease limiting speed is 3,300 r/min and the oil rating 4,400 r/min; mass about 1940 g."
      },
      {
        "q": "How is the 7928 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 190 mm OD and 24 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7928 support?",
        "a": "One 7928 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7928?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,300 r/min and the oil rating 4,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7928?",
        "a": "The 140/190/24 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 83.5 kN / C0 90 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7928",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7928"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7028",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7028",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 210,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 133,
    "static_load_kN": 133,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 6.85,
    "limiting_speed_rpm": 3100,
    "max_rpm": 3100,
    "speed_oil_rpm": 4100,
    "weight_g": 3960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7028 is an NTN single-row angular contact ball bearing: standard-section 7000 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 140 x 210 x 33 mm. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 3960 g, which at this 35.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Choose the standard-section 7000 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 140 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7028 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 3,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 133/133 kN ratings and 6.85 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7028; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7028?",
        "a": "7028 is a single-row angular contact ball bearing to ISO 15: 140 mm bore, 210 mm outside diameter, 33 mm width (5.512 x 8.268 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 133 kN, C0 133 kN and a 6.85 kN fatigue load limit Pu; the grease limiting speed is 3,100 r/min and the oil rating 4,100 r/min; mass about 3960 g."
      },
      {
        "q": "How is the 7028 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 210 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7028 support?",
        "a": "One 7028 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7028?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,100 r/min and the oil rating 4,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7028?",
        "a": "The 140/210/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 133 kN / C0 133 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7028-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×210×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7028"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7228",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7228",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 250,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 225,
    "static_load_kN": 215,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 11.7,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3600,
    "weight_g": 8780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 140 x 250 x 42 mm, NTN 7228 sits in the medium-duty 7200 single-row family of the angular-contact programme. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. Size selection is usually finished by checking that the C0 of 215 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Heat-mounting to 80-90 deg C is the clean route onto a 140 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 140 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 2,700 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 225/215 kN ratings and 11.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7228; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7228?",
        "a": "7228 is a single-row angular contact ball bearing to ISO 15: 140 mm bore, 250 mm outside diameter, 42 mm width (5.512 x 9.843 x 1.654 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 225 kN, C0 215 kN and a 11.7 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min; mass about 8780 g."
      },
      {
        "q": "How is the 7228 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 250 mm OD and 42 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7228 support?",
        "a": "One 7228 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7228?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7228?",
        "a": "The 140/250/42 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 225 kN / C0 215 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7228-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7228-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7228"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7228B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7228B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 250,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 203,
    "static_load_kN": 195,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 10.1,
    "limiting_speed_rpm": 2300,
    "max_rpm": 2300,
    "speed_oil_rpm": 3100,
    "weight_g": 8780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7228B carries a 140 mm bore in a 250 mm outside diameter, 42 mm wide envelope. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 28 encodes the 140 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The static margin, C0 195 kN versus C 203 kN, is what supports slow oscillating duty and shock without immediate brinelling. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 140 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,300 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7228B without re-checking axial float, heat and housing width — the kinematics differ.",
      "Do not pair two random 7228B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 203/195 kN ratings and 10.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7228B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7228B?",
        "a": "7228B is a single-row angular contact ball bearing to ISO 15: 140 mm bore, 250 mm outside diameter, 42 mm width (5.512 x 9.843 x 1.654 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 203 kN, C0 195 kN and a 10.1 kN fatigue load limit Pu; the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min; mass about 8780 g."
      },
      {
        "q": "How is the 7228B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 28 encodes the 140 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 250 mm OD and 42 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7228B support?",
        "a": "One 7228B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7228B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7228B?",
        "a": "The 140/250/42 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 203 kN / C0 195 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7228B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7228b",
      "7228B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7328",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7328",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 300,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 335,
    "static_load_kN": 335,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 17.7,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3300,
    "weight_g": 21500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7328 measures 140 mm across the bore, 300 mm over the outer ring and 62 mm across the faces. Decoding 7328: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 335 kN static rating into useful one-direction thrust capacity. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Heat-mounting to 80-90 deg C is the clean route onto a 140 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 140 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7328 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A 7328 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 335/335 kN ratings and 17.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7328; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7328?",
        "a": "7328 is a single-row angular contact ball bearing to ISO 15: 140 mm bore, 300 mm outside diameter, 62 mm width (5.512 x 11.811 x 2.441 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 335 kN, C0 335 kN and a 17.7 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min; mass about 21500 g."
      },
      {
        "q": "How is the 7328 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 28 encodes the 140 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 300 mm OD and 62 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7328 support?",
        "a": "One 7328 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7328?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7328?",
        "a": "The 140/300/62 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 335 kN / C0 335 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7328-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×300×62 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7328"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7328B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7328B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 300,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 305,
    "static_load_kN": 310,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 16.3,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 2800,
    "weight_g": 21500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7328B appears as a heavy-duty 7300 single-row family bearing of 140 mm bore, 300 mm outside diameter and 62 mm width. Decoding 7328B: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 28 encodes the 140 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). On speed, the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min. For a 140 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 140 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 310 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The C0 of 310 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 305/310 kN ratings and 16.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7328B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7328B?",
        "a": "7328B is a single-row angular contact ball bearing to ISO 15: 140 mm bore, 300 mm outside diameter, 62 mm width (5.512 x 11.811 x 2.441 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 305 kN, C0 310 kN and a 16.3 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min; mass about 21500 g."
      },
      {
        "q": "How is the 7328B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 28 encodes the 140 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 300 mm OD and 62 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7328B support?",
        "a": "One 7328B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7328B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7328B?",
        "a": "The 140/300/62 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 305 kN / C0 310 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7328B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7328b",
      "7328B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7930",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7930",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 210,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 108,
    "static_load_kN": 117,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 5.8,
    "limiting_speed_rpm": 3100,
    "max_rpm": 3100,
    "speed_oil_rpm": 4100,
    "weight_g": 2960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7930 appears as a extra-light, high-speed 7900 single-row family bearing of 150 mm bore, 210 mm outside diameter and 28 mm width. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. On speed, the grease limiting speed is 3,100 r/min and the oil rating 4,100 r/min. Choose the extra-light, high-speed 7900 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 150 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 117 kN really covers the worst static case before substituting it for a 7000.",
      "Grease rated for deep-groove motor duty is not automatically right at 3,100 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7930 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The C0 of 117 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 108/117 kN ratings and 5.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7930; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7930?",
        "a": "7930 is a single-row angular contact ball bearing to ISO 15: 150 mm bore, 210 mm outside diameter, 28 mm width (5.906 x 8.268 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 108 kN, C0 117 kN and a 5.8 kN fatigue load limit Pu; the grease limiting speed is 3,100 r/min and the oil rating 4,100 r/min; mass about 2960 g."
      },
      {
        "q": "How is the 7930 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 210 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7930 support?",
        "a": "One 7930 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7930?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 3,100 r/min and the oil rating 4,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7930?",
        "a": "The 150/210/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 108 kN / C0 117 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7930",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7930"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7030",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7030",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 225,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 152,
    "static_load_kN": 154,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 7.65,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3800,
    "weight_g": 4820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7030 belongs to the standard-section 7000 single-row family: the catalogue boundary dimensions read 150 / 225 / 35 mm (bore / OD / width). The designation breaks down as 70 is the single-row dimension series (standard-section 7000 single-row family); 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 154 kN versus C 152 kN, is what supports slow oscillating duty and shock without immediate brinelling. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 150 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "On a 150 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "On a 150 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Do not pair two random 7030 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 152/154 kN ratings and 7.65 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7030; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7030?",
        "a": "7030 is a single-row angular contact ball bearing to ISO 15: 150 mm bore, 225 mm outside diameter, 35 mm width (5.906 x 8.858 x 1.378 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 152 kN, C0 154 kN and a 7.65 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min; mass about 4820 g."
      },
      {
        "q": "How is the 7030 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 225 mm OD and 35 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7030 support?",
        "a": "One 7030 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7030?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7030?",
        "a": "The 150/225/35 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 152 kN / C0 154 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7030-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×225×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7030"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7230",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7230",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 270,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 257,
    "static_load_kN": 259,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 13.7,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3400,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7230 measures 150 mm across the bore, 270 mm over the outer ring and 45 mm across the faces. Decoding 7230: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 257 kN and C0 259 kN, each mm of bore carries about 1.71 kN of dynamic rating. The 150/270/45 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 150 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 2,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "On a 150 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 257/259 kN ratings and 13.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7230; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7230?",
        "a": "7230 is a single-row angular contact ball bearing to ISO 15: 150 mm bore, 270 mm outside diameter, 45 mm width (5.906 x 10.63 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 257 kN, C0 259 kN and a 13.7 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min; mass about 11000 g."
      },
      {
        "q": "How is the 7230 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 270 mm OD and 45 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7230 support?",
        "a": "One 7230 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7230?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7230?",
        "a": "The 150/270/45 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 257 kN / C0 259 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7230-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×270×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7230"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7230B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7230B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 270,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 232,
    "static_load_kN": 235,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 11.9,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 2900,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7230B belongs to the medium-duty 7200 single-row family: the catalogue boundary dimensions read 150 / 270 / 45 mm (bore / OD / width). Decoding 7230B: 72 is the single-row dimension series (medium-duty 7200 single-row family), with 30 encodes the 150 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). On speed, the grease limiting speed is 2,200 r/min and the oil rating 2,900 r/min. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. A 150 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 150 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 235 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "On a 150 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The C0 of 235 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "The 232/235 kN ratings and 11.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7230B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7230B?",
        "a": "7230B is a single-row angular contact ball bearing to ISO 15: 150 mm bore, 270 mm outside diameter, 45 mm width (5.906 x 10.63 x 1.772 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 232 kN, C0 235 kN and a 11.9 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 2,900 r/min; mass about 11000 g."
      },
      {
        "q": "How is the 7230B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 30 encodes the 150 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 270 mm OD and 45 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7230B support?",
        "a": "One 7230B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7230B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,200 r/min and the oil rating 2,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7230B?",
        "a": "The 150/270/45 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 232 kN / C0 235 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7230B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7230b",
      "7230B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7330",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7330",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 320,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 365,
    "static_load_kN": 380,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 19.5,
    "limiting_speed_rpm": 2300,
    "max_rpm": 2300,
    "speed_oil_rpm": 3100,
    "weight_g": 25100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7330 appears as a heavy-duty 7300 single-row family bearing of 150 mm bore, 320 mm outside diameter and 65 mm width. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 365 kN against C0 380 kN — a C0/C ratio of 1.04 that is typical of an angular-contact contact ellipse. Against a deep-groove bearing of the same 150 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 150 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7330 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 380 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 365/380 kN ratings and 19.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7330; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7330?",
        "a": "7330 is a single-row angular contact ball bearing to ISO 15: 150 mm bore, 320 mm outside diameter, 65 mm width (5.906 x 12.598 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 365 kN, C0 380 kN and a 19.5 kN fatigue load limit Pu; the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min; mass about 25100 g."
      },
      {
        "q": "How is the 7330 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 30 encodes the 150 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 320 mm OD and 65 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7330 support?",
        "a": "One 7330 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7330?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7330?",
        "a": "The 150/320/65 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 365 kN / C0 380 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7330-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7330"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7330B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7330B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 320,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 335,
    "static_load_kN": 350,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 17.9,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2600,
    "weight_g": 25100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7330B is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 150 x 320 x 65 mm. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 30 encodes the 150 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The static margin, C0 350 kN versus C 335 kN, is what supports slow oscillating duty and shock without immediate brinelling. Size selection is usually finished by checking that the C0 of 350 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 150 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 2,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Do not pair two random 7330B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 335/350 kN ratings and 17.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7330B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7330B?",
        "a": "7330B is a single-row angular contact ball bearing to ISO 15: 150 mm bore, 320 mm outside diameter, 65 mm width (5.906 x 12.598 x 2.559 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 335 kN, C0 350 kN and a 17.9 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,600 r/min; mass about 25100 g."
      },
      {
        "q": "How is the 7330B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 30 encodes the 150 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 320 mm OD and 65 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7330B support?",
        "a": "One 7330B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7330B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,000 r/min and the oil rating 2,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7330B?",
        "a": "The 150/320/65 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 335 kN / C0 350 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7330B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7330b",
      "7330B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7932",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7932",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 220,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 109,
    "static_load_kN": 121,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 5.8,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "speed_oil_rpm": 3800,
    "weight_g": 3130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The extra-light, high-speed 7900 single-row family entry 7932 carries a 160 mm bore in a 220 mm outside diameter, 28 mm wide envelope. NTN builds the number from 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), then 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 121 kN versus C 109 kN, is what supports slow oscillating duty and shock without immediate brinelling. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 160 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 121 kN really covers the worst static case before substituting it for a 7000.",
      "Do not pair two random 7932 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The C0 of 121 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Do not pair two random 7932 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 109/121 kN ratings and 5.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7932; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7932?",
        "a": "7932 is a single-row angular contact ball bearing to ISO 15: 160 mm bore, 220 mm outside diameter, 28 mm width (6.299 x 8.661 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 109 kN, C0 121 kN and a 5.8 kN fatigue load limit Pu; the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min; mass about 3130 g."
      },
      {
        "q": "How is the 7932 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 220 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7932 support?",
        "a": "One 7932 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7932?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,800 r/min and the oil rating 3,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7932?",
        "a": "The 160/220/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 109 kN / C0 121 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7932",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7932"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7032",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7032",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 240,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 172,
    "static_load_kN": 176,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 8.55,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3600,
    "weight_g": 5960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 160 x 240 x 38 mm, NTN 7032 sits in the standard-section 7000 single-row family of the angular-contact programme. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 172 kN against C0 176 kN — a C0/C ratio of 1.02 that is typical of an angular-contact contact ellipse. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 160 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The C0 of 176 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7032 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 172/176 kN ratings and 8.55 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7032; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7032?",
        "a": "7032 is a single-row angular contact ball bearing to ISO 15: 160 mm bore, 240 mm outside diameter, 38 mm width (6.299 x 9.449 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 172 kN, C0 176 kN and a 8.55 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min; mass about 5960 g."
      },
      {
        "q": "How is the 7032 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 240 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7032 support?",
        "a": "One 7032 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7032?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7032?",
        "a": "The 160/240/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 172 kN / C0 176 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7032",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7032"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7232",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7232",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 290,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 291,
    "static_load_kN": 305,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 15.8,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3200,
    "weight_g": 13700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7232 appears as a medium-duty 7200 single-row family bearing of 160 mm bore, 290 mm outside diameter and 48 mm width. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 3,200 r/min sits 800 r/min above the 2,400 r/min grease figure — a 1.33x step that says how much headroom oil cooling buys. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Heat-mounting to 80-90 deg C is the clean route onto a 160 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 160 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7232 without re-checking axial float, heat and housing width — the kinematics differ.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,400 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 291/305 kN ratings and 15.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7232; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7232?",
        "a": "7232 is a single-row angular contact ball bearing to ISO 15: 160 mm bore, 290 mm outside diameter, 48 mm width (6.299 x 11.417 x 1.89 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 291 kN, C0 305 kN and a 15.8 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,200 r/min; mass about 13700 g."
      },
      {
        "q": "How is the 7232 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 290 mm OD and 48 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7232 support?",
        "a": "One 7232 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7232?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,400 r/min and the oil rating 3,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7232?",
        "a": "The 160/290/48 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 291 kN / C0 305 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7232-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 160×290×48 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7232"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7232B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7232B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 290,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 263,
    "static_load_kN": 279,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 13.7,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2700,
    "weight_g": 13700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7232B appears as a medium-duty 7200 single-row family bearing of 160 mm bore, 290 mm outside diameter and 48 mm width. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 32 encodes the 160 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue dynamic rating C is 263 kN against C0 279 kN — a C0/C ratio of 1.06 that is typical of an angular-contact contact ellipse. Size selection is usually finished by checking that the C0 of 279 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Grease quantity matters as much as grade at 2,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 160 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The 2,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 2,000 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 263/279 kN ratings and 13.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7232B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7232B?",
        "a": "7232B is a single-row angular contact ball bearing to ISO 15: 160 mm bore, 290 mm outside diameter, 48 mm width (6.299 x 11.417 x 1.89 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 263 kN, C0 279 kN and a 13.7 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,700 r/min; mass about 13700 g."
      },
      {
        "q": "How is the 7232B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 32 encodes the 160 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 290 mm OD and 48 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7232B support?",
        "a": "One 7232B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7232B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,000 r/min and the oil rating 2,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7232B?",
        "a": "The 160/290/48 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 263 kN / C0 279 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7232B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7232b",
      "7232B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7332",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7332",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 340,
    "B_mm": 68,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 385,
    "static_load_kN": 420,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 20.9,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 2800,
    "weight_g": 29800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7332 carries a 160 mm bore in a 340 mm outside diameter, 68 mm wide envelope. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 385 kN dynamic and 420 kN static for this size and a 20.9 kN fatigue load limit Pu. The 160/340/68 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Heat-mounting to 80-90 deg C is the clean route onto a 160 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 160 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7332 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 385/420 kN ratings and 20.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7332; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7332?",
        "a": "7332 is a single-row angular contact ball bearing to ISO 15: 160 mm bore, 340 mm outside diameter, 68 mm width (6.299 x 13.386 x 2.677 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 385 kN, C0 420 kN and a 20.9 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min; mass about 29800 g."
      },
      {
        "q": "How is the 7332 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 32 encodes the 160 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 340 mm OD and 68 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7332 support?",
        "a": "One 7332 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7332?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7332?",
        "a": "The 160/340/68 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 385 kN / C0 420 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7332",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7332"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7332B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7332B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 340,
    "B_mm": 68,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 350,
    "static_load_kN": 385,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 19.1,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2400,
    "weight_g": 29800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the heavy-duty 7300 single-row family, 7332B measures 160 mm across the bore, 340 mm over the outer ring and 68 mm across the faces. The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 32 encodes the 160 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). NTN prints 350 kN dynamic and 385 kN static for this size and a 19.1 kN fatigue load limit Pu. Choose the heavy-duty 7300 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 160 mm bore give the working limits. ",
    "applications": [
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 160 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Do not pair two random 7332B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7332B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 350/385 kN ratings and 19.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7332B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7332B?",
        "a": "7332B is a single-row angular contact ball bearing to ISO 15: 160 mm bore, 340 mm outside diameter, 68 mm width (6.299 x 13.386 x 2.677 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 350 kN, C0 385 kN and a 19.1 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min; mass about 29800 g."
      },
      {
        "q": "How is the 7332B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 32 encodes the 160 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 340 mm OD and 68 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7332B support?",
        "a": "One 7332B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7332B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7332B?",
        "a": "The 160/340/68 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 350 kN / C0 385 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7332B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7332b",
      "7332B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7934",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7934",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 230,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 115,
    "static_load_kN": 129,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 6.05,
    "limiting_speed_rpm": 2700,
    "max_rpm": 2700,
    "speed_oil_rpm": 3600,
    "weight_g": 3290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7934 is the 170 mm bore member of NTN's extra-light, high-speed 7900 single-row family, with a 230 mm outside diameter and 28 mm section width. Reading the code: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 115 kN against C0 129 kN — a C0/C ratio of 1.12 that is typical of an angular-contact contact ellipse. Against a deep-groove bearing of the same 170 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 170 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 129 kN really covers the worst static case before substituting it for a 7000.",
      "On a 170 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 115/129 kN ratings and 6.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7934; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7934?",
        "a": "7934 is a single-row angular contact ball bearing to ISO 15: 170 mm bore, 230 mm outside diameter, 28 mm width (6.693 x 9.055 x 1.102 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 115 kN, C0 129 kN and a 6.05 kN fatigue load limit Pu; the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min; mass about 3290 g."
      },
      {
        "q": "How is the 7934 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 230 mm OD and 28 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7934 support?",
        "a": "One 7934 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7934?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,700 r/min and the oil rating 3,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7934?",
        "a": "The 170/230/28 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 115 kN / C0 129 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7934",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7934"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7034",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7034",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 260,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 206,
    "static_load_kN": 214,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 10.2,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3300,
    "weight_g": 7960,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the standard-section 7000 single-row family, 7034 measures 170 mm across the bore, 260 mm over the outer ring and 42 mm across the faces. NTN builds the number from 70 is the single-row dimension series (standard-section 7000 single-row family), then 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 206 kN dynamic and 214 kN static for this size and a 10.2 kN fatigue load limit Pu. Choose the standard-section 7000 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 170 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7034 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The C0 of 214 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7034 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 206/214 kN ratings and 10.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7034; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7034?",
        "a": "7034 is a single-row angular contact ball bearing to ISO 15: 170 mm bore, 260 mm outside diameter, 42 mm width (6.693 x 10.236 x 1.654 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 206 kN, C0 214 kN and a 10.2 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min; mass about 7960 g."
      },
      {
        "q": "How is the 7034 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 260 mm OD and 42 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7034 support?",
        "a": "One 7034 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7034?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7034?",
        "a": "The 170/260/42 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 206 kN / C0 214 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7034-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×260×42 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7034"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7234",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7234",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 310,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 325,
    "static_load_kN": 360,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 18,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 3000,
    "weight_g": 17000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The medium-duty 7200 single-row family entry 7234 carries a 170 mm bore in a 310 mm outside diameter, 52 mm wide envelope. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. At roughly 70.0 mm of radial section, the catalogue still quotes 325 kN dynamic capacity for the 170 mm bore. Size selection is usually finished by checking that the C0 of 360 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Grease quantity matters as much as grade at 2,200 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 170 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Do not pair two random 7234 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 325/360 kN ratings and 18 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7234; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7234?",
        "a": "7234 is a single-row angular contact ball bearing to ISO 15: 170 mm bore, 310 mm outside diameter, 52 mm width (6.693 x 12.205 x 2.047 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 325 kN, C0 360 kN and a 18 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 3,000 r/min; mass about 17000 g."
      },
      {
        "q": "How is the 7234 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 310 mm OD and 52 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7234 support?",
        "a": "One 7234 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7234?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,200 r/min and the oil rating 3,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7234?",
        "a": "The 170/310/52 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 325 kN / C0 360 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7234-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×310×52 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7234"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7234B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7234B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 310,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 295,
    "static_load_kN": 325,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 15.6,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "speed_oil_rpm": 2500,
    "weight_g": 17000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7234B is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 170 x 310 x 52 mm. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 34 encodes the 170 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Catalogue mass is about 17000 g, which at this 70.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Choose the medium-duty 7200 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Heat-mounting to 80-90 deg C is the clean route onto a 170 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 170 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Do not pair two random 7234B bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 295/325 kN ratings and 15.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7234B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7234B?",
        "a": "7234B is a single-row angular contact ball bearing to ISO 15: 170 mm bore, 310 mm outside diameter, 52 mm width (6.693 x 12.205 x 2.047 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 295 kN, C0 325 kN and a 15.6 kN fatigue load limit Pu; the grease limiting speed is 1,900 r/min and the oil rating 2,500 r/min; mass about 17000 g."
      },
      {
        "q": "How is the 7234B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 34 encodes the 170 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 310 mm OD and 52 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7234B support?",
        "a": "One 7234B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7234B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,900 r/min and the oil rating 2,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7234B?",
        "a": "The 170/310/52 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 295 kN / C0 325 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7234B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7234b",
      "7234B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7334",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7334",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 360,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 430,
    "static_load_kN": 485,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 23.3,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2700,
    "weight_g": 35300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7334 is the 170 mm bore member of NTN's heavy-duty 7300 single-row family, with a 360 mm outside diameter and 72 mm section width. Reading the code: 73 is the single-row dimension series (heavy-duty 7300 single-row family), 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 35300 g, which at this 95.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Grease quantity matters as much as grade at 2,000 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 170 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 7334 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 430/485 kN ratings and 23.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7334; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7334?",
        "a": "7334 is a single-row angular contact ball bearing to ISO 15: 170 mm bore, 360 mm outside diameter, 72 mm width (6.693 x 14.173 x 2.835 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 430 kN, C0 485 kN and a 23.3 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,700 r/min; mass about 35300 g."
      },
      {
        "q": "How is the 7334 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 34 encodes the 170 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 360 mm OD and 72 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7334 support?",
        "a": "One 7334 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7334?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,000 r/min and the oil rating 2,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7334?",
        "a": "The 170/360/72 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 430 kN / C0 485 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7334-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×360×72 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=132",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7334"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7334B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7334B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 360,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 395,
    "static_load_kN": 445,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 21.3,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2300,
    "weight_g": 35300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7334B is the 170 mm bore member of NTN's heavy-duty 7300 single-row family, with a 360 mm outside diameter and 72 mm section width. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 34 encodes the 170 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 40 deg contact angle is the lever that turns the 445 kN static rating into useful one-direction thrust capacity. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 170 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 170 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 445 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 7334B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 395/445 kN ratings and 21.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7334B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7334B?",
        "a": "7334B is a single-row angular contact ball bearing to ISO 15: 170 mm bore, 360 mm outside diameter, 72 mm width (6.693 x 14.173 x 2.835 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 395 kN, C0 445 kN and a 21.3 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,300 r/min; mass about 35300 g."
      },
      {
        "q": "How is the 7334B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 34 encodes the 170 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 360 mm OD and 72 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7334B support?",
        "a": "One 7334B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7334B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,700 r/min and the oil rating 2,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7334B?",
        "a": "The 170/360/72 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 395 kN / C0 445 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7334B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7334b",
      "7334B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7936",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7936",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 250,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 145,
    "static_load_kN": 163,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 7.4,
    "limiting_speed_rpm": 2500,
    "max_rpm": 2500,
    "speed_oil_rpm": 3300,
    "weight_g": 4870,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7936 is an NTN single-row angular contact ball bearing: extra-light, high-speed 7900 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 180 x 250 x 33 mm. Decoding 7936: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 145 kN dynamic and 163 kN static for this size and a 7.4 kN fatigue load limit Pu. The 180/250/33 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Heat-mounting to 80-90 deg C is the clean route onto a 180 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 163 kN really covers the worst static case before substituting it for a 7000.",
      "The C0 of 163 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "A 7936 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7936 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 145/163 kN ratings and 7.4 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7936; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7936?",
        "a": "7936 is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 250 mm outside diameter, 33 mm width (7.087 x 9.843 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 145 kN, C0 163 kN and a 7.4 kN fatigue load limit Pu; the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min; mass about 4870 g."
      },
      {
        "q": "How is the 7936 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 250 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7936 support?",
        "a": "One 7936 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7936?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,500 r/min and the oil rating 3,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7936?",
        "a": "The 180/250/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 145 kN / C0 163 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7936",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7936"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7036",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7036",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 280,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 242,
    "static_load_kN": 266,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 12.3,
    "limiting_speed_rpm": 2300,
    "max_rpm": 2300,
    "speed_oil_rpm": 3100,
    "weight_g": 10400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7036 appears as a standard-section 7000 single-row family bearing of 180 mm bore, 280 mm outside diameter and 46 mm width. Reading the code: 70 is the single-row dimension series (standard-section 7000 single-row family), 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 10400 g, which at this 50.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. If the duty is mainly high speed with modest thrust, the 7900-series cross-section is the lighter alternative; if thrust dominates, the 7300-series section carries more. Heat-mounting to 80-90 deg C is the clean route onto a 180 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 242/266 kN ratings and 12.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7036; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7036?",
        "a": "7036 is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 280 mm outside diameter, 46 mm width (7.087 x 11.024 x 1.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 242 kN, C0 266 kN and a 12.3 kN fatigue load limit Pu; the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min; mass about 10400 g."
      },
      {
        "q": "How is the 7036 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 280 mm OD and 46 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7036 support?",
        "a": "One 7036 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7036?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,300 r/min and the oil rating 3,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7036?",
        "a": "The 180/280/46 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 242 kN / C0 266 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7036-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×280×46 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7036"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7236",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7236",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 320,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 340,
    "static_load_kN": 385,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 18.6,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 2800,
    "weight_g": 17700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7236 is the 180 mm bore member of NTN's medium-duty 7200 single-row family, with a 320 mm outside diameter and 52 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. For a 180 mm shaft with combined load, the practical shortlist is this series, its 7300-series heavier section, and — where thrust reverses — a back-to-back pair rather than a single row. A 180 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 2,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 2,100 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 340/385 kN ratings and 18.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7236; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7236?",
        "a": "7236 is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 320 mm outside diameter, 52 mm width (7.087 x 12.598 x 2.047 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 340 kN, C0 385 kN and a 18.6 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min; mass about 17700 g."
      },
      {
        "q": "How is the 7236 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 320 mm OD and 52 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7236 support?",
        "a": "One 7236 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7236?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7236?",
        "a": "The 180/320/52 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 340 kN / C0 385 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7236-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×320×52 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7236"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7236B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7236B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 320,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 305,
    "static_load_kN": 350,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 16.1,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2400,
    "weight_g": 17700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the medium-duty 7200 single-row family, 7236B measures 180 mm across the bore, 320 mm over the outer ring and 52 mm across the faces. The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 36 encodes the 180 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). With C 305 kN and C0 350 kN, each mm of bore carries about 1.69 kN of dynamic rating. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "A 7236B mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "On a 180 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 305/350 kN ratings and 16.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7236B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7236B?",
        "a": "7236B is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 320 mm outside diameter, 52 mm width (7.087 x 12.598 x 2.047 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 305 kN, C0 350 kN and a 16.1 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min; mass about 17700 g."
      },
      {
        "q": "How is the 7236B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 36 encodes the 180 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 320 mm OD and 52 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7236B support?",
        "a": "One 7236B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7236B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7236B?",
        "a": "The 180/320/52 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 305 kN / C0 350 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7236B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7236b",
      "7236B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7336",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7336",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 380,
    "B_mm": 75,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 455,
    "static_load_kN": 535,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 24.9,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "speed_oil_rpm": 2500,
    "weight_g": 40900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7336 is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 180 x 380 x 75 mm. Decoding 7336: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 535 kN static rating into useful one-direction thrust capacity. Size selection is usually finished by checking that the C0 of 535 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. A 180 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "The 1,900 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "A 7336 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 455/535 kN ratings and 24.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7336; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7336?",
        "a": "7336 is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 380 mm outside diameter, 75 mm width (7.087 x 14.961 x 2.953 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 455 kN, C0 535 kN and a 24.9 kN fatigue load limit Pu; the grease limiting speed is 1,900 r/min and the oil rating 2,500 r/min; mass about 40900 g."
      },
      {
        "q": "How is the 7336 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 36 encodes the 180 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 380 mm OD and 75 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7336 support?",
        "a": "One 7336 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7336?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,900 r/min and the oil rating 2,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7336?",
        "a": "The 180/380/75 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 455 kN / C0 535 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7336-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×380×75 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7336"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7336B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7336B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 380,
    "B_mm": 75,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 415,
    "static_load_kN": 490,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 22.8,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2100,
    "weight_g": 40900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 180 x 380 x 75 mm, NTN 7336B sits in the heavy-duty 7300 single-row family of the angular-contact programme. Decoding 7336B: 73 is the single-row dimension series (heavy-duty 7300 single-row family), with 36 encodes the 180 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The oil rating of 2,100 r/min sits 500 r/min above the 1,600 r/min grease figure — a 1.31x step that says how much headroom oil cooling buys. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Grease quantity matters as much as grade at 1,600 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 180 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The 1,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,600 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,600 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 415/490 kN ratings and 22.8 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7336B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7336B?",
        "a": "7336B is a single-row angular contact ball bearing to ISO 15: 180 mm bore, 380 mm outside diameter, 75 mm width (7.087 x 14.961 x 2.953 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 415 kN, C0 490 kN and a 22.8 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,100 r/min; mass about 40900 g."
      },
      {
        "q": "How is the 7336B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 36 encodes the 180 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 380 mm OD and 75 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7336B support?",
        "a": "One 7336B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7336B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,600 r/min and the oil rating 2,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7336B?",
        "a": "The 180/380/75 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 415 kN / C0 490 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7336B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7336b",
      "7336B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7938",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7938",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 260,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 147,
    "static_load_kN": 169,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 7.45,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "speed_oil_rpm": 3200,
    "weight_g": 5100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7938 belongs to the extra-light, high-speed 7900 single-row family: the catalogue boundary dimensions read 190 / 260 / 33 mm (bore / OD / width). The designation breaks down as 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue mass is about 5100 g, which at this 35.0 mm radial section keeps the bearing comfortably inside high-speed spindle weight budgets. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Grease quantity matters as much as grade at 2,400 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 190 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 169 kN really covers the worst static case before substituting it for a 7000.",
      "A 7938 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 147/169 kN ratings and 7.45 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7938; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7938?",
        "a": "7938 is a single-row angular contact ball bearing to ISO 15: 190 mm bore, 260 mm outside diameter, 33 mm width (7.48 x 10.236 x 1.299 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 147 kN, C0 169 kN and a 7.45 kN fatigue load limit Pu; the grease limiting speed is 2,400 r/min and the oil rating 3,200 r/min; mass about 5100 g."
      },
      {
        "q": "How is the 7938 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 260 mm OD and 33 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7938 support?",
        "a": "One 7938 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7938?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,400 r/min and the oil rating 3,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7938?",
        "a": "The 190/260/33 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 147 kN / C0 169 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7938",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7938"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7038",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7038",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 290,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 248,
    "static_load_kN": 280,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 12.6,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 2900,
    "weight_g": 10800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The standard-section 7000 single-row family entry 7038 carries a 190 mm bore in a 290 mm outside diameter, 46 mm wide envelope. Decoding 7038: 70 is the single-row dimension series (standard-section 7000 single-row family), with 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 280 kN static rating into useful one-direction thrust capacity. Against a deep-groove bearing of the same 190 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Grease quantity matters as much as grade at 2,200 r/min: fill about a third of the free space and let the bearing purge on first run. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 190 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "A 7038 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "A 7038 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 248/280 kN ratings and 12.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7038; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7038?",
        "a": "7038 is a single-row angular contact ball bearing to ISO 15: 190 mm bore, 290 mm outside diameter, 46 mm width (7.48 x 11.417 x 1.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 248 kN, C0 280 kN and a 12.6 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 2,900 r/min; mass about 10800 g."
      },
      {
        "q": "How is the 7038 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 290 mm OD and 46 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7038 support?",
        "a": "One 7038 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7038?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,200 r/min and the oil rating 2,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7038?",
        "a": "The 190/290/46 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 248 kN / C0 280 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7038-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×290×46 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7038"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7238",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7238",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 340,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 335,
    "static_load_kN": 390,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 17.9,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2600,
    "weight_g": 21300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7238 is an NTN single-row angular contact ball bearing: medium-duty 7200 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 190 x 340 x 55 mm. Reading the code: 72 is the single-row dimension series (medium-duty 7200 single-row family), 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The radial section height here is 75.0 mm, and the catalogue couples that with C 335 kN / C0 390 kN. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 190 mm bore give the working limits. ",
    "applications": [
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 190 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Grease rated for deep-groove motor duty is not automatically right at 2,000 r/min with preload; check the grease speed factor against the catalogue figure.",
      "On a 190 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 335/390 kN ratings and 17.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7238; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7238?",
        "a": "7238 is a single-row angular contact ball bearing to ISO 15: 190 mm bore, 340 mm outside diameter, 55 mm width (7.48 x 13.386 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 335 kN, C0 390 kN and a 17.9 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,600 r/min; mass about 21300 g."
      },
      {
        "q": "How is the 7238 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 340 mm OD and 55 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7238 support?",
        "a": "One 7238 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7238?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,000 r/min and the oil rating 2,600 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7238?",
        "a": "The 190/340/55 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 335 kN / C0 390 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7238-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7238"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7238B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7238B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 340,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 300,
    "static_load_kN": 355,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 15.5,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2200,
    "weight_g": 21300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7238B is the 190 mm bore member of NTN's medium-duty 7200 single-row family, with a 340 mm outside diameter and 55 mm section width. NTN builds the number from 72 is the single-row dimension series (medium-duty 7200 single-row family), then 38 encodes the 190 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). At roughly 75.0 mm of radial section, the catalogue still quotes 300 kN dynamic capacity for the 190 mm bore. Where the same envelope must also be sealed, or where mounting mistakes are likely, compare with the double-row 52/53 catalogue pages before fixing the bill of materials. Set preload or end-play with the pair as a unit and lock the adjustment; a single angular-contact bearing cannot run free like a deep-groove one. ",
    "applications": [
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 190 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7238B without re-checking axial float, heat and housing width — the kinematics differ.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 300/355 kN ratings and 15.5 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7238B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7238B?",
        "a": "7238B is a single-row angular contact ball bearing to ISO 15: 190 mm bore, 340 mm outside diameter, 55 mm width (7.48 x 13.386 x 2.165 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 300 kN, C0 355 kN and a 15.5 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,200 r/min; mass about 21300 g."
      },
      {
        "q": "How is the 7238B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 38 encodes the 190 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 340 mm OD and 55 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7238B support?",
        "a": "One 7238B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7238B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,700 r/min and the oil rating 2,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7238B?",
        "a": "The 190/340/55 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 300 kN / C0 355 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7238B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7238b",
      "7238B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7338",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7338",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 400,
    "B_mm": 78,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 475,
    "static_load_kN": 585,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 26.6,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2300,
    "weight_g": 47000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7338 belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 190 / 400 / 78 mm (bore / OD / width). The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. With C 475 kN and C0 585 kN, each mm of bore carries about 2.50 kN of dynamic rating. For a 190 mm shaft with combined load, the practical shortlist is this series, its 7200-series lighter section, and — where thrust reverses — a back-to-back pair rather than a single row. Shaft and housing shoulders must clear the ring corners yet support enough face — the catalogue abutment diameters for the 190 mm bore give the working limits. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 190 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7338 without re-checking axial float, heat and housing width — the kinematics differ.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "On a 190 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "The 475/585 kN ratings and 26.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7338; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7338?",
        "a": "7338 is a single-row angular contact ball bearing to ISO 15: 190 mm bore, 400 mm outside diameter, 78 mm width (7.48 x 15.748 x 3.071 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 475 kN, C0 585 kN and a 26.6 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,300 r/min; mass about 47000 g."
      },
      {
        "q": "How is the 7338 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 38 encodes the 190 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 400 mm OD and 78 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7338 support?",
        "a": "One 7338 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7338?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,800 r/min and the oil rating 2,300 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7338?",
        "a": "The 190/400/78 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 475 kN / C0 585 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7338-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7338"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7338B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7338B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 400,
    "B_mm": 78,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 430,
    "static_load_kN": 535,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 24,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "speed_oil_rpm": 2000,
    "weight_g": 47000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The heavy-duty 7300 single-row family entry 7338B carries a 190 mm bore in a 400 mm outside diameter, 78 mm wide envelope. Two fields make up the code — 73 is the single-row dimension series (heavy-duty 7300 single-row family) and 38 encodes the 190 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. The 190/400/78 envelope is an ISO 15 boundary plan, so dimensional interchange with other makers holds — ratings and internal geometry do not automatically follow. Heat-mounting to 80-90 deg C is the clean route onto a 190 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 190 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,500 r/min with preload; check the grease speed factor against the catalogue figure.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "The 1,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 430/535 kN ratings and 24 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7338B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7338B?",
        "a": "7338B is a single-row angular contact ball bearing to ISO 15: 190 mm bore, 400 mm outside diameter, 78 mm width (7.48 x 15.748 x 3.071 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 430 kN, C0 535 kN and a 24 kN fatigue load limit Pu; the grease limiting speed is 1,500 r/min and the oil rating 2,000 r/min; mass about 47000 g."
      },
      {
        "q": "How is the 7338B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 38 encodes the 190 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 400 mm OD and 78 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7338B support?",
        "a": "One 7338B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7338B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,500 r/min and the oil rating 2,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7338B?",
        "a": "The 190/400/78 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 430 kN / C0 535 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7338B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7338b",
      "7338B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7940",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7940",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 280,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 205,
    "static_load_kN": 231,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 9.9,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "speed_oil_rpm": 3000,
    "weight_g": 7150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 200 x 280 x 38 mm, NTN 7940 sits in the extra-light, high-speed 7900 single-row family of the angular-contact programme. NTN builds the number from 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), then 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The static margin, C0 231 kN versus C 205 kN, is what supports slow oscillating duty and shock without immediate brinelling. Against a deep-groove bearing of the same 200 mm bore, this bearing trades some pure-radial comfort for real one-direction thrust capacity and higher running accuracy. Heat-mounting to 80-90 deg C is the clean route onto a 200 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 200 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 231 kN really covers the worst static case before substituting it for a 7000.",
      "On a 200 mm shaft, an interference fit eats internal clearance; skipping the clearance/preload recalculation is the classic cause of a new bearing running 20 deg C hotter than the drawing suggests.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Do not pair two random 7940 bearings from stock and expect catalogue paired ratings — matched-set grinding is what makes DB/DF/DT preload behave, and NTN sells those as separate order numbers.",
      "The 205/231 kN ratings and 9.9 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7940; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7940?",
        "a": "7940 is a single-row angular contact ball bearing to ISO 15: 200 mm bore, 280 mm outside diameter, 38 mm width (7.874 x 11.024 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 205 kN, C0 231 kN and a 9.9 kN fatigue load limit Pu; the grease limiting speed is 2,200 r/min and the oil rating 3,000 r/min; mass about 7150 g."
      },
      {
        "q": "How is the 7940 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 280 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7940 support?",
        "a": "One 7940 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7940?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,200 r/min and the oil rating 3,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7940?",
        "a": "The 200/280/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 205 kN / C0 231 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7940",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7940"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7040",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7040",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 310,
    "B_mm": 51,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 279,
    "static_load_kN": 325,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.3,
    "limiting_speed_rpm": 2100,
    "max_rpm": 2100,
    "speed_oil_rpm": 2800,
    "weight_g": 14000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7040 is the 200 mm bore member of NTN's standard-section 7000 single-row family, with a 310 mm outside diameter and 51 mm section width. Two fields make up the code — 70 is the single-row dimension series (standard-section 7000 single-row family) and 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. Catalogue dynamic rating C is 279 kN against C0 325 kN — a C0/C ratio of 1.16 that is typical of an angular-contact contact ellipse. Choose the standard-section 7000 single-row family when the shaft needs a stiff locating support and the axial component is known to act mostly one way. Heat-mounting to 80-90 deg C is the clean route onto a 200 mm shaft; drive-fits through the balls transmit force through the contact ellipse and can brinell it. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 200 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "A 7040 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "The 279/325 kN ratings and 14.3 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7040; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7040?",
        "a": "7040 is a single-row angular contact ball bearing to ISO 15: 200 mm bore, 310 mm outside diameter, 51 mm width (7.874 x 12.205 x 2.008 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 279 kN, C0 325 kN and a 14.3 kN fatigue load limit Pu; the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min; mass about 14000 g."
      },
      {
        "q": "How is the 7040 designation structured?",
        "a": "70 is the single-row dimension series (standard-section 7000 single-row family); 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 310 mm OD and 51 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7040 support?",
        "a": "One 7040 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7040?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,100 r/min and the oil rating 2,800 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7040?",
        "a": "The 200/310/51 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 279 kN / C0 325 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7040-BGM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 200×310×51 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7040"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7240",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7240",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 360,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 375,
    "static_load_kN": 450,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 20.2,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "speed_oil_rpm": 2500,
    "weight_g": 25300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7240 belongs to the medium-duty 7200 single-row family: the catalogue boundary dimensions read 200 / 360 / 58 mm (bore / OD / width). The designation breaks down as 72 is the single-row dimension series (medium-duty 7200 single-row family); 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The oil rating of 2,500 r/min sits 600 r/min above the 1,900 r/min grease figure — a 1.32x step that says how much headroom oil cooling buys. Size selection is usually finished by checking that the C0 of 450 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. A 200 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 200 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7240 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,900 r/min with preload; check the grease speed factor against the catalogue figure.",
      "The 375/450 kN ratings and 20.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7240; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7240?",
        "a": "7240 is a single-row angular contact ball bearing to ISO 15: 200 mm bore, 360 mm outside diameter, 58 mm width (7.874 x 14.173 x 2.283 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 375 kN, C0 450 kN and a 20.2 kN fatigue load limit Pu; the grease limiting speed is 1,900 r/min and the oil rating 2,500 r/min; mass about 25300 g."
      },
      {
        "q": "How is the 7240 designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 360 mm OD and 58 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7240 support?",
        "a": "One 7240 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7240?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,900 r/min and the oil rating 2,500 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7240?",
        "a": "The 200/360/58 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 375 kN / C0 450 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7240-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 200×360×58 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7240"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7240B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7240B",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 360,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 335,
    "static_load_kN": 410,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 17.6,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "speed_oil_rpm": 2100,
    "weight_g": 25300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 200 x 360 x 58 mm, NTN 7240B sits in the medium-duty 7200 single-row family of the angular-contact programme. Two fields make up the code — 72 is the single-row dimension series (medium-duty 7200 single-row family) and 40 encodes the 200 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). Because the contact line is angled, one bearing of this type takes radial load plus thrust from one direction only — the opposite direction needs a second bearing or a matched set. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 200 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,600 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7240B without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 1,600 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "The 335/410 kN ratings and 17.6 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7240B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7240B?",
        "a": "7240B is a single-row angular contact ball bearing to ISO 15: 200 mm bore, 360 mm outside diameter, 58 mm width (7.874 x 14.173 x 2.283 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 335 kN, C0 410 kN and a 17.6 kN fatigue load limit Pu; the grease limiting speed is 1,600 r/min and the oil rating 2,100 r/min; mass about 25300 g."
      },
      {
        "q": "How is the 7240B designation structured?",
        "a": "72 is the single-row dimension series (medium-duty 7200 single-row family); 40 encodes the 200 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 360 mm OD and 58 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7240B support?",
        "a": "One 7240B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7240B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,600 r/min and the oil rating 2,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7240B?",
        "a": "The 200/360/58 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 335 kN / C0 410 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7240B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7240b",
      "7240B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7340",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7340",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 420,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 500,
    "static_load_kN": 610,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 27,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2200,
    "weight_g": 53100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "At 200 x 420 x 80 mm, NTN 7340 sits in the heavy-duty 7300 single-row family of the angular-contact programme. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 500 kN dynamic and 610 kN static for this size and a 27 kN fatigue load limit Pu. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 200 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 200 mm bore bearing forgives nothing in a poorly machined housing.",
      "The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Grease rated for deep-groove motor duty is not automatically right at 1,700 r/min with preload; check the grease speed factor against the catalogue figure.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7340 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 500/610 kN ratings and 27 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7340; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7340?",
        "a": "7340 is a single-row angular contact ball bearing to ISO 15: 200 mm bore, 420 mm outside diameter, 80 mm width (7.874 x 16.535 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 500 kN, C0 610 kN and a 27 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,200 r/min; mass about 53100 g."
      },
      {
        "q": "How is the 7340 designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 40 encodes the 200 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 420 mm OD and 80 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7340 support?",
        "a": "One 7340 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7340?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,700 r/min and the oil rating 2,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7340?",
        "a": "The 200/420/80 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 500 kN / C0 610 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7340-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7340"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7340B",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7340B",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 420,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 455,
    "static_load_kN": 555,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 24.7,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "speed_oil_rpm": 1900,
    "weight_g": 53100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7340B belongs to the heavy-duty 7300 single-row family: the catalogue boundary dimensions read 200 / 420 / 80 mm (bore / OD / width). The designation breaks down as 73 is the single-row dimension series (heavy-duty 7300 single-row family); 40 encodes the 200 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). At roughly 110.0 mm of radial section, the catalogue still quotes 455 kN dynamic capacity for the 200 mm bore. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 200 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 40 deg B-execution raises axial capacity but lowers the speed ceiling — do not copy the standard-bearing speed and preload settings onto it.",
      "The C0 of 555 kN is a static rating, not a permissible running thrust — sizing continuous axial load from C0 alone is a recurring drawing-office error.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "The 455/555 kN ratings and 24.7 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7340B; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7340B?",
        "a": "7340B is a single-row angular contact ball bearing to ISO 15: 200 mm bore, 420 mm outside diameter, 80 mm width (7.874 x 16.535 x 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 455 kN, C0 555 kN and a 24.7 kN fatigue load limit Pu; the grease limiting speed is 1,400 r/min and the oil rating 1,900 r/min; mass about 53100 g."
      },
      {
        "q": "How is the 7340B designation structured?",
        "a": "73 is the single-row dimension series (heavy-duty 7300 single-row family); 40 encodes the 200 mm bore (bore code x 5), and the trailing B marks the 40 deg contact-angle execution (the no-letter standard bearing works at 30 deg). The 420 mm OD and 80 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7340B support?",
        "a": "One 7340B alone takes thrust in one direction only, along its 40 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7340B?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,400 r/min and the oil rating 1,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7340B?",
        "a": "The 200/420/80 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 455 kN / C0 555 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7340B",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7340b",
      "7340B"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7944",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7944",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 220,
    "D_mm": 300,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 207,
    "static_load_kN": 239,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 9.85,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "speed_oil_rpm": 2700,
    "weight_g": 7740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "In NTN Ball and Roller Bearings CAT.No.2203E, 7944 appears as a extra-light, high-speed 7900 single-row family bearing of 220 mm bore, 300 mm outside diameter and 38 mm width. Decoding 7944: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 44 encodes the 220 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 207 kN dynamic and 239 kN static for this size and a 9.85 kN fatigue load limit Pu. Selection starts from the thrust share: as axial load grows past roughly half the radial load, an angular-contact position of this section usually outlives a deep-groove one. A 220 mm shaft typically takes a m6/n6 fit for rotating inner-ring load; keep the housing bore to G6/H6 class so the contact geometry is not distorted. ",
    "applications": [
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 220 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 239 kN really covers the worst static case before substituting it for a 7000.",
      "A 7944 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7944 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 207/239 kN ratings and 9.85 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7944; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7944?",
        "a": "7944 is a single-row angular contact ball bearing to ISO 15: 220 mm bore, 300 mm outside diameter, 38 mm width (8.661 x 11.811 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 207 kN, C0 239 kN and a 9.85 kN fatigue load limit Pu; the grease limiting speed is 2,000 r/min and the oil rating 2,700 r/min; mass about 7740 g."
      },
      {
        "q": "How is the 7944 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 44 encodes the 220 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 300 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7944 support?",
        "a": "One 7944 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7944?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 2,000 r/min and the oil rating 2,700 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7944?",
        "a": "The 220/300/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 207 kN / C0 239 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7944",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7944"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7948",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7948",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 240,
    "D_mm": 320,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 213,
    "static_load_kN": 255,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 10.1,
    "limiting_speed_rpm": 1800,
    "max_rpm": 1800,
    "speed_oil_rpm": 2400,
    "weight_g": 8340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7948 is the 240 mm bore member of NTN's extra-light, high-speed 7900 single-row family, with a 320 mm outside diameter and 38 mm section width. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 48 encodes the 240 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 255 kN static rating into useful one-direction thrust capacity. For a 240 mm shaft with combined load, the practical shortlist is this series, its 7000-series standard section, and — where thrust reverses — a back-to-back pair rather than a single row. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 240 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 255 kN really covers the worst static case before substituting it for a 7000.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "The 1,800 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "A 7948 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 213/255 kN ratings and 10.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7948; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7948?",
        "a": "7948 is a single-row angular contact ball bearing to ISO 15: 240 mm bore, 320 mm outside diameter, 38 mm width (9.449 x 12.598 x 1.496 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 213 kN, C0 255 kN and a 10.1 kN fatigue load limit Pu; the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min; mass about 8340 g."
      },
      {
        "q": "How is the 7948 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 48 encodes the 240 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 320 mm OD and 38 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7948 support?",
        "a": "One 7948 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7948?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,800 r/min and the oil rating 2,400 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7948?",
        "a": "The 240/320/38 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 213 kN / C0 255 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7948",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7948"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7952",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7952",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 260,
    "D_mm": 360,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 285,
    "static_load_kN": 375,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.1,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "speed_oil_rpm": 2200,
    "weight_g": 14000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "NTN 7952 belongs to the extra-light, high-speed 7900 single-row family: the catalogue boundary dimensions read 260 / 360 / 46 mm (bore / OD / width). Decoding 7952: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 52 encodes the 260 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 285 kN dynamic and 375 kN static for this size and a 14.1 kN fatigue load limit Pu. Size selection is usually finished by checking that the C0 of 375 kN covers the maximum static or shock condition with the catalogue safety factor, not only the running load. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away. ",
    "applications": [
      "large fan, blower and turbo-compressor rotors",
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "resin-cage cracking on the 7900-series sizes after hot, dry running or solvent attack on the polymer",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 260 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 375 kN really covers the worst static case before substituting it for a 7000.",
      "A single-row angular contact left loose on the shaft to \"help assembly\" will fret the seat: the contact angle keeps driving the ring axially under load.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7952 without re-checking axial float, heat and housing width — the kinematics differ.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7952 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 285/375 kN ratings and 14.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7952; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7952?",
        "a": "7952 is a single-row angular contact ball bearing to ISO 15: 260 mm bore, 360 mm outside diameter, 46 mm width (10.236 x 14.173 x 1.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 285 kN, C0 375 kN and a 14.1 kN fatigue load limit Pu; the grease limiting speed is 1,700 r/min and the oil rating 2,200 r/min; mass about 14000 g."
      },
      {
        "q": "How is the 7952 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 52 encodes the 260 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 360 mm OD and 46 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7952 support?",
        "a": "One 7952 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7952?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,700 r/min and the oil rating 2,200 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7952?",
        "a": "The 260/360/46 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 285 kN / C0 375 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7952",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7952"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7956",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7956",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 280,
    "D_mm": 380,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 289,
    "static_load_kN": 385,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 14.1,
    "limiting_speed_rpm": 1500,
    "max_rpm": 1500,
    "speed_oil_rpm": 2100,
    "weight_g": 14800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "From the extra-light, high-speed 7900 single-row family, 7956 measures 280 mm across the bore, 380 mm over the outer ring and 46 mm across the faces. Two fields make up the code — 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family) and 56 encodes the 280 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 385 kN static rating into useful one-direction thrust capacity. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "rolling-mill backup and drive spindles",
      "crusher and mill pinion shafts",
      "large pump and turbine auxiliary shafts",
      "steel-plant conveyor and table roll drives"
    ],
    "failure_modes": [
      "false brinelling on the raceway contact ellipses when a preloaded spindle sits vibrating at standstill — visible as evenly spaced flute-like wear at ball pitch",
      "thermal runaway from excessive preload: the pair runs hot, grease darkens and the contact ellipse spreads until the raceways smear",
      "machined-cage land scoring when a high-speed spindle runs past its grease rating and the cage runs dry on its guidance surface",
      "lubricant starvation scoring at the ball/raceway contact when grease volume or relubrication interval is guessed instead of calculated",
      "contamination-induced denting — hard particles rolled into the contact ellipse become the initiation points for surface fatigue"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 280 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 385 kN really covers the worst static case before substituting it for a 7000.",
      "The 1,500 r/min speed figure assumes the catalogue lubrication state and a correctly set pair; real limits drop fast with excess grease fill or heavy preload.",
      "Catalogue mass and ratings belong to the open execution; shields, seals and resin cages change both the speed ceiling and the thermal behaviour of the same basic size.",
      "A 7956 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.",
      "The 289/385 kN ratings and 14.1 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7956; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7956?",
        "a": "7956 is a single-row angular contact ball bearing to ISO 15: 280 mm bore, 380 mm outside diameter, 46 mm width (11.024 x 14.961 x 1.811 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 289 kN, C0 385 kN and a 14.1 kN fatigue load limit Pu; the grease limiting speed is 1,500 r/min and the oil rating 2,100 r/min; mass about 14800 g."
      },
      {
        "q": "How is the 7956 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 56 encodes the 280 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 380 mm OD and 46 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7956 support?",
        "a": "One 7956 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7956?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,500 r/min and the oil rating 2,100 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7956?",
        "a": "The 280/380/46 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 289 kN / C0 385 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7956",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7956"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7960",
    "brand": "NTN",
    "manufacturer_designation": "NTN 7960",
    "series": "7900-series",
    "type": "angular_contact",
    "d_mm": 300,
    "D_mm": 420,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "dynamic_load_kN": 360,
    "static_load_kN": 520,
    "cage_type": "brass",
    "fatigue_load_limit_kN": 18.2,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "speed_oil_rpm": 1900,
    "weight_g": 23700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "The extra-light, high-speed 7900 single-row family entry 7960 carries a 300 mm bore in a 420 mm outside diameter, 56 mm wide envelope. Decoding 7960: 79 is the single-row dimension series (extra-light, high-speed 7900 single-row family), with 60 encodes the 300 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. NTN prints 360 kN dynamic and 520 kN static for this size and a 18.2 kN fatigue load limit Pu. For a 300 mm shaft with combined load, the practical shortlist is this series, its 7000-series standard section, and — where thrust reverses — a back-to-back pair rather than a single row. After mounting, check axial float or preload with a dial gauge on the shaft end — the specification, not hand feel, decides whether the contact angle works as rated. ",
    "applications": [
      "steel-plant conveyor and table roll drives",
      "wind-turbine and heavy-machinery auxiliaries",
      "heavy industrial gearbox main shafts",
      "large fan, blower and turbo-compressor rotors"
    ],
    "failure_modes": [
      "impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle",
      "loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow",
      "pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed",
      "flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share",
      "current-erosion pitting on VFD-driven motor shafts, first visible as a grey frosted band across both raceways"
    ],
    "pitfalls": [
      "At this size the shaft fit, shoulder geometry and preload procedure dominate the outcome; a 300 mm bore bearing forgives nothing in a poorly machined housing.",
      "The 7900 extra-light section is chosen for speed and stiffness, not for load margin — check that C0 520 kN really covers the worst static case before substituting it for a 7000.",
      "If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.",
      "Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.",
      "Never use a four-point or double-row bearing as a like-for-like swap for a single 7960 without re-checking axial float, heat and housing width — the kinematics differ.",
      "The 360/520 kN ratings and 18.2 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7960; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue ratings of NTN 7960?",
        "a": "7960 is a single-row angular contact ball bearing to ISO 15: 300 mm bore, 420 mm outside diameter, 56 mm width (11.811 x 16.535 x 2.205 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 360 kN, C0 520 kN and a 18.2 kN fatigue load limit Pu; the grease limiting speed is 1,400 r/min and the oil rating 1,900 r/min; mass about 23700 g."
      },
      {
        "q": "How is the 7960 designation structured?",
        "a": "79 is the single-row dimension series (extra-light, high-speed 7900 single-row family); 60 encodes the 300 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 420 mm OD and 56 mm width follow the ISO 15 boundary-dimension plan for that series."
      },
      {
        "q": "Which axial direction does 7960 support?",
        "a": "One 7960 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact."
      },
      {
        "q": "What lubrication speeds does NTN print for 7960?",
        "a": "Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 1,400 r/min and the oil rating 1,900 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit."
      },
      {
        "q": "What should be checked before substituting another make for 7960?",
        "a": "The 300/420/56 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 360 kN / C0 520 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7960",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://www.ntnglobal.com/en/products/catalog/pdf/ntn_ball_roller_2203E.pdf#page=133",
    "catalog_ver": "NTN Ball and Roller Bearings CAT.No.2203E",
    "extracted_at": "2026-10-01",
    "last_verified": "2026-10-01",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7960"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7200",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7200 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 30,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 7.02,
    "static_load_kN": 3.35,
    "fatigue_load_limit_kN": 0.14,
    "reference_speed_rpm": 30000,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 10 mm shaft carrying combined load, SKF lists 7200 under catalogue execution 7200 BEP: one open single-row angular-contact ball bearing, 40° contact angle, in the light (7200) series of the 7xxx family.Digit by digit, 7200 reads as bearing type 7 (single-row angular contact), light section diameter series 2, and bore reference 00 resolving to 10 mm (codes 00-03 use the 10/12/15/17 mm exception table); 30 mm OD and 9 width are the matching ISO 15 boundary values. Suffix letters after 7200 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. Catalogue mass 30 g for the 10×30×9 mm open execution covers the PA66 cage and standard ball complement; sealed or brass-cage variants of the same size differ slightly in mass and carry their own order numbers. A single 7200 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "encoder and resolver mountings",
      "instrument and rotary-table drives",
      "dental and laboratory high-speed rotors",
      "small machine-tool spindles and high-speed heads"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "At a 10 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7200 shows up as spindle vibration long before it fails.",
      "The 72xx light section at 10 mm bore is the general-purpose angular-contact envelope (30×9 mm); stepping up to a 7300 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7200 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "At the 7.02 kN rating of 7200, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 30,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Open 7200 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 7.02/3.35 kN ratings are SKF catalogue 17000 values for the 7200 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7200 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7200 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7200 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7200?",
        "a": "The SKF 7200 BEP is a single-row angular-contact ball bearing with 10 mm bore, 30 mm outer diameter and 9 mm width (0.394 × 1.181 × 0.354 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 7.02 kN, C0 3.35 kN, fatigue load limit Pu 0.14 kN, reference speed 30,000 r/min, limiting speed 30,000 r/min, mass about 30 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 30,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7200 bore code work?",
        "a": "The last two digits of 7200 are bore code 00, giving a 10 mm bore under the exception table. The 30 mm OD and 9 mm width come from the ISO 15 diameter-series plan, shared with the 6200 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7200 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7200 compare with a deep-groove 6200?",
        "a": "Both use the 10×30×9 mm ISO 15 envelope, but the angular-contact 7200 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7200 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7200-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 10×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6200",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6200-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6200-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6200-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7200-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7200 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7200-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7200 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7200 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7201",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7201 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 36,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 7.61,
    "static_load_kN": 3.8,
    "fatigue_load_limit_kN": 0.16,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7201 (7201 BEP) is the light (7200) series angular-contact choice for a 12 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 32×10 mm ISO 15 envelope.Numbering ties the bearing to its envelope: 7201 means angular-contact type 7, light section section 2, 12 mm bore (codes 00-03 use the 10/12/15/17 mm exception table) — which is why the 32×10 mm outline swaps dimensionally with a 6201, though the load behaviour does not. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7201 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. At 28,000 r/min reference speed the 10.0 mm-section 7201 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 26,000 r/min as the mechanical ceiling. Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7201 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 12 mm shaft positions.",
    "applications": [
      "dental and laboratory high-speed rotors",
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At a 12 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7201 shows up as spindle vibration long before it fails.",
      "The 72xx light section at 12 mm bore is the general-purpose angular-contact envelope (32×10 mm); stepping up to a 7301 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Do not mix execution classes inside one 7201 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7201 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "Shaft and housing fillets must clear the bearing chamfer so the 10 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 7.61/3.8 kN ratings are SKF catalogue 17000 values for the 7201 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7201 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7201 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7201 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7201?",
        "a": "The SKF 7201 BEP is a single-row angular-contact ball bearing with 12 mm bore, 32 mm outer diameter and 10 mm width (0.472 × 1.26 × 0.394 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 7.61 kN, C0 3.8 kN, fatigue load limit Pu 0.16 kN, reference speed 28,000 r/min, limiting speed 26,000 r/min, mass about 36 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7201 bore code work?",
        "a": "The last two digits of 7201 are bore code 01, giving a 12 mm bore under the exception table. The 32 mm OD and 10 mm width come from the ISO 15 diameter-series plan, shared with the 6201 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7201 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7201 compare with a deep-groove 6201?",
        "a": "Both use the 12×32×10 mm ISO 15 envelope, but the angular-contact 7201 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6201 cannot be dropped into a combined-load 7201 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7201-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "6201",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6201-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6201-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6201-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7201-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7201 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7201-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7201 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7201 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7202 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 45,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 8.32,
    "static_load_kN": 4.4,
    "fatigue_load_limit_kN": 0.183,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "Ordering number 7202 BEP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 15 mm shaft, light (7200) series, with an open PA66-caged execution and one-direction axial capacity.On the SKF nameplate, 7202 follows the ISO numbering convention: 7 for the angular-contact type, 2 for the light section section, final digits 02 for the 15 mm bore (codes 00-03 use the 10/12/15/17 mm exception table). In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Speed planning uses two different ceilings: 24,000 r/min reference (thermal, under representative load) and 24,000 r/min limiting (mechanical cage/ball limit) — for this size the catalogue lists them at the same value. Specify pairs rather than single units wherever thrust reverses: the 40° angle of 7202 generates an induced axial load under radial force, and an unpaired bearing on a reversing shaft will run slack in one direction and fret its seat.",
    "applications": [
      "servo and stepper motor shafts",
      "textile and wire-guide spindles",
      "small gear pumps and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "At a 15 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7202 shows up as spindle vibration long before it fails.",
      "The 72xx light section at 15 mm bore is the general-purpose angular-contact envelope (35×11 mm); stepping up to a 7302 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7202 mounting error.",
      "Do not mix execution classes inside one 7202 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Catalogue reference speed and limiting speed are different limits: the 24,000 r/min reference is a thermal criterion under load, while the 24,000 r/min limiting value is the mechanical ceiling — observe both.",
      "The 8.32/4.4 kN ratings are SKF catalogue 17000 values for the 7202 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7202 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7202 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7202 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7202?",
        "a": "The SKF 7202 BEP is a single-row angular-contact ball bearing with 15 mm bore, 35 mm outer diameter and 11 mm width (0.591 × 1.378 × 0.433 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 8.32 kN, C0 4.4 kN, fatigue load limit Pu 0.183 kN, reference speed 24,000 r/min, limiting speed 24,000 r/min, mass about 45 g. It is an open 40° contact-angle bearing with a PA66 cage. For this size the two values coincide, so either thermal or mechanical conditions set the same ceiling."
      },
      {
        "q": "How does the 7202 bore code work?",
        "a": "The last two digits of 7202 are bore code 02, giving a 15 mm bore under the exception table. The 35 mm OD and 11 mm width come from the ISO 15 diameter-series plan, shared with the 6202 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7202 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7202 compare with a deep-groove 6202?",
        "a": "Both use the 15×35×11 mm ISO 15 envelope, but the angular-contact 7202 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 8.32 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6202",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6202-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6202-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6202-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7202-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7202 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7202-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7202 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7202-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7202 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7202-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7202 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-202-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 202 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7203 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 65,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 10.4,
    "static_load_kN": 5.5,
    "fatigue_load_limit_kN": 0.236,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7203 is SKF's single-row angular-contact ball bearing in the light (7200) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7203 BEP in the SKF Rolling Bearings catalogue.The code breaks down as type prefix 7 (angular contact), diameter series 2 (the light section), and bore code 03 = 17 mm (codes 00-03 use the 10/12/15/17 mm exception table); dimensions 17×40×12 mm therefore match the 6203 deep-groove envelope even though the internal design is different. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). With C 10.4 kN and C0 5.5 kN, the 7203 pair-sizing check is dominated by the axial share: keep the equivalent load P below the rating at the required L10, remembering one bearing alone cannot cover reversing thrust at 20,000 r/min. Because the contact line runs at 40°, one 7203 reacts thrust in a single direction; bidirectional shafts need a DB or DF pair with defined preload, and a rotating inner ring on a 17 mm shaft typically takes a j5 seat with an H7 housing bore.",
    "applications": [
      "small gear pumps and metering pumps",
      "encoder and resolver mountings",
      "instrument and rotary-table drives",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "At a 17 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7203 shows up as spindle vibration long before it fails.",
      "The 72xx light section at 17 mm bore is the general-purpose angular-contact envelope (40×12 mm); stepping up to a 7303 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7203 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7203 mounting error.",
      "The 7203 shares its ISO 15 envelope with deep-groove 6203 but is not a drop-in replacement: it cannot run effectively under pure radial load without a minimum axial load, and a deep-groove bearing cannot replace its combined-load duty.",
      "The 10.4/5.5 kN ratings are SKF catalogue 17000 values for the 7203 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7203 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7203 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7203 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7203?",
        "a": "The SKF 7203 BEP is a single-row angular-contact ball bearing with 17 mm bore, 40 mm outer diameter and 12 mm width (0.669 × 1.575 × 0.472 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 10.4 kN, C0 5.5 kN, fatigue load limit Pu 0.236 kN, reference speed 22,000 r/min, limiting speed 20,000 r/min, mass about 65 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 22,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7203 bore code work?",
        "a": "The last two digits of 7203 are bore code 03, giving a 17 mm bore under the exception table. The 40 mm OD and 12 mm width come from the ISO 15 diameter-series plan, shared with the 6203 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7203 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7203 compare with a deep-groove 6203?",
        "a": "Both use the 17×40×12 mm ISO 15 envelope, but the angular-contact 7203 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7203 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6203",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6203-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6203-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6203-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7203 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7203 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7203 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7203 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7203 BEY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7203 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 203 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7204 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 110,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 13.3,
    "static_load_kN": 7.65,
    "fatigue_load_limit_kN": 0.325,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "The SKF 7204 BEP is a 20×47×14 mm single-row angular-contact ball bearing — the light (7200) series of the SKF 7xxx line, built on the ISO 15 envelope shared with the 6204 deep-groove size but cut for combined radial and one-direction axial load.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 2 is ISO diameter series 2 (light section), and the last two digits encode the 20 mm bore; the 47 mm OD and 14 mm width follow the ISO 15 general plan. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. The 0.325 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.58 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. For a 20 mm shaft the usual seat is k5 with an H7 housing when the inner ring rotates; arrange two 7204 bearings as a set for two-direction location and set preload from the load diagram, never from assembly feel.",
    "applications": [
      "instrument and rotary-table drives",
      "dental and laboratory high-speed rotors",
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At a 20 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7204 shows up as spindle vibration long before it fails.",
      "The 72xx light section at 20 mm bore is the general-purpose angular-contact envelope (47×14 mm); stepping up to a 7304 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7204 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7204 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the inner ring only, or brinell marks on the 47 mm race release as noise within the first running hours.",
      "The 13.3/7.65 kN ratings are SKF catalogue 17000 values for the 7204 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7204 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7204 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7204 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7204?",
        "a": "The SKF 7204 BEP is a single-row angular-contact ball bearing with 20 mm bore, 47 mm outer diameter and 14 mm width (0.787 × 1.85 × 0.551 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 13.3 kN, C0 7.65 kN, fatigue load limit Pu 0.325 kN, reference speed 19,000 r/min, limiting speed 18,000 r/min, mass about 110 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7204 bore code work?",
        "a": "The last two digits of 7204 are bore code 04, so 04 × 5 = 20 mm bore. The 47 mm OD and 14 mm width come from the ISO 15 diameter-series plan, shared with the 6204 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7204 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7204 compare with a deep-groove 6204?",
        "a": "Both use the 20×47×14 mm ISO 15 envelope, but the angular-contact 7204 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6204 cannot be dropped into a combined-load 7204 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6204",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6204-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6204-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6204-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7204 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7204 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7204 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7204 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7204 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7204 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7204 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7205 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 130,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 14.8,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "In SKF catalogue PUB BU/P1 17000, 7205 appears as 7205 BEP: a 40° contact-angle, open, one-direction-thrust ball bearing in the light (7200) series, supplied with a glass-fibre PA66 cage as standard.Digit by digit, 7205 reads as bearing type 7 (single-row angular contact), light section diameter series 2, and bore reference 05 resolving to 25 mm; 52 mm OD and 15 width are the matching ISO 15 boundary values. Suffix letters after 7205 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. Selection arithmetic: the C0/C ratio is about 0.63 (static 9.3 kN against dynamic 14.8 kN), typical of a 40° angle sized for axial capacity, and the 0.4 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. Mounting practice for 7205: the rotating ring takes the interference fit (k5 on a 25 mm rotating shaft), the stationary ring slides for axial location, and reversing-thrust duty demands a paired DB/DF set rather than one bearing.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "pre-grease degradation after long shelf storage without rotation or re-greasing"
    ],
    "pitfalls": [
      "On this 25 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7205 pair heats, loses preload control and smears the raceways.",
      "The 72xx light section at 25 mm bore is the general-purpose angular-contact envelope (52×15 mm); stepping up to a 7305 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "A single 7205 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7205 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 14.8/9.3 kN ratings are SKF catalogue 17000 values for the 7205 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7205 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7205 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7205 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7205?",
        "a": "The SKF 7205 BEP is a single-row angular-contact ball bearing with 25 mm bore, 52 mm outer diameter and 15 mm width (0.984 × 2.047 × 0.591 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 14.8 kN, C0 9.3 kN, fatigue load limit Pu 0.4 kN, reference speed 16,000 r/min, limiting speed 15,000 r/min, mass about 130 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 15,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7205 bore code work?",
        "a": "The last two digits of 7205 are bore code 05, so 05 × 5 = 25 mm bore. The 52 mm OD and 15 mm width come from the ISO 15 diameter-series plan, shared with the 6205 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7205 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7205 compare with a deep-groove 6205?",
        "a": "Both use the 25×52×15 mm ISO 15 envelope, but the angular-contact 7205 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 14.8 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6205",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6205-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6205-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6205-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BEY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7205 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7205 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 205 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7206 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 200,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.61,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7206 BEP belongs to SKF's universal single-row angular-contact range — the 30 mm bore entry in the light (7200) series, dimensioned 62 mm OD and 16 mm wide to the same ISO 15 boundary plan as the 6206 deep-groove envelope.Numbering ties the bearing to its envelope: 7206 means angular-contact type 7, light section section 2, 30 mm bore — which is why the 62×16 mm outline swaps dimensionally with a 6206, though the load behaviour does not. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7206 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 16.0 mm radial section height ((62−30)/2) and 200 g catalogue mass frame a 30 mm bore bearing rated at 22.5 kN C — roughly 0.75 kN of dynamic capacity per millimetre of bore before application factors. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7206 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "automotive and industrial transmissions",
      "belt-driven fan and blower shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "false brinelling on idle paired sets exposed to machine vibration",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "mounting score marks when the bearing is cocked over the shaft keyway or a burr"
    ],
    "pitfalls": [
      "On this 30 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7206 pair heats, loses preload control and smears the raceways.",
      "The 72xx light section at 30 mm bore is the general-purpose angular-contact envelope (62×16 mm); stepping up to a 7306 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "At the 22.5 kN rating of 7206, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 13,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "A single 7206 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "The 200 g mass and 16 mm width mean locknut and spacer faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the contact angle and concentrates load on one shoulder of 7206.",
      "The 22.5/14.3 kN ratings are SKF catalogue 17000 values for the 7206 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7206 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7206 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7206 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7206?",
        "a": "The SKF 7206 BEP is a single-row angular-contact ball bearing with 30 mm bore, 62 mm outer diameter and 16 mm width (1.181 × 2.441 × 0.63 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 22.5 kN, C0 14.3 kN, fatigue load limit Pu 0.61 kN, reference speed 13,000 r/min, limiting speed 13,000 r/min, mass about 200 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 13,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7206 bore code work?",
        "a": "The last two digits of 7206 are bore code 06, so 06 × 5 = 30 mm bore. The 62 mm OD and 16 mm width come from the ISO 15 diameter-series plan, shared with the 6206 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7206 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7206 compare with a deep-groove 6206?",
        "a": "Both use the 30×62×16 mm ISO 15 envelope, but the angular-contact 7206 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7206 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "6206",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6206-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6206-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6206-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7206 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7206 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7206 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7206 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7206 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7206 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7206 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 206 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 206 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7207 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 280,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 29.1,
    "static_load_kN": 19,
    "fatigue_load_limit_kN": 0.815,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 35 mm shaft carrying combined load, SKF lists 7207 under catalogue execution 7207 BEP: one open single-row angular-contact ball bearing, 40° contact angle, in the light (7200) series of the 7xxx family.On the SKF nameplate, 7207 follows the ISO numbering convention: 7 for the angular-contact type, 2 for the light section section, final digits 07 for the 35 mm bore. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Catalogue mass 280 g for the 35×72×17 mm open execution covers the PA66 cage and standard ball complement; sealed or brass-cage variants of the same size differ slightly in mass and carry their own order numbers. A single 7207 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "automotive and industrial transmissions",
      "belt-driven fan and blower shafts",
      "printing cylinders and packaging machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "On this 35 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7207 pair heats, loses preload control and smears the raceways.",
      "The 72xx light section at 35 mm bore is the general-purpose angular-contact envelope (72×17 mm); stepping up to a 7307 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7207 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "At the 29.1 kN rating of 7207, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 11,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Open 7207 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 29.1/19 kN ratings are SKF catalogue 17000 values for the 7207 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7207 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7207 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7207 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7207?",
        "a": "The SKF 7207 BEP is a single-row angular-contact ball bearing with 35 mm bore, 72 mm outer diameter and 17 mm width (1.378 × 2.835 × 0.669 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 29.1 kN, C0 19 kN, fatigue load limit Pu 0.815 kN, reference speed 11,000 r/min, limiting speed 11,000 r/min, mass about 280 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7207 bore code work?",
        "a": "The last two digits of 7207 are bore code 07, so 07 × 5 = 35 mm bore. The 72 mm OD and 17 mm width come from the ISO 15 diameter-series plan, shared with the 6207 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7207 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7207 compare with a deep-groove 6207?",
        "a": "Both use the 35×72×17 mm ISO 15 envelope, but the angular-contact 7207 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6207 cannot be dropped into a combined-load 7207 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6207",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6207-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6207-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7207 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7207 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7207 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7207 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7207 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7207 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 207 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7208 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 370,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 34.5,
    "static_load_kN": 24,
    "fatigue_load_limit_kN": 1.02,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7208 (7208 BEP) is the light (7200) series angular-contact choice for a 40 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 80×18 mm ISO 15 envelope.The code breaks down as type prefix 7 (angular contact), diameter series 2 (the light section), and bore code 08 = 40 mm; dimensions 40×80×18 mm therefore match the 6208 deep-groove envelope even though the internal design is different. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). At 10,000 r/min reference speed the 20.0 mm-section 7208 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 10,000 r/min as the mechanical ceiling. Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7208 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 40 mm shaft positions.",
    "applications": [
      "printing cylinders and packaging machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "On this 40 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7208 pair heats, loses preload control and smears the raceways.",
      "The 72xx light section at 40 mm bore is the general-purpose angular-contact envelope (80×18 mm); stepping up to a 7308 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Do not mix execution classes inside one 7208 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7208 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "Shaft and housing fillets must clear the bearing chamfer so the 18 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 34.5/24 kN ratings are SKF catalogue 17000 values for the 7208 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7208 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7208 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7208 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7208?",
        "a": "The SKF 7208 BEP is a single-row angular-contact ball bearing with 40 mm bore, 80 mm outer diameter and 18 mm width (1.575 × 3.15 × 0.709 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 34.5 kN, C0 24 kN, fatigue load limit Pu 1.02 kN, reference speed 10,000 r/min, limiting speed 10,000 r/min, mass about 370 g. It is an open 40° contact-angle bearing with a PA66 cage. For this size the two values coincide, so either thermal or mechanical conditions set the same ceiling."
      },
      {
        "q": "How does the 7208 bore code work?",
        "a": "The last two digits of 7208 are bore code 08, so 08 × 5 = 40 mm bore. The 80 mm OD and 18 mm width come from the ISO 15 diameter-series plan, shared with the 6208 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7208 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7208 compare with a deep-groove 6208?",
        "a": "Both use the 40×80×18 mm ISO 15 envelope, but the angular-contact 7208 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 34.5 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6208",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6208-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6208-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6208-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7208 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7208 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7208 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7208 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7208 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7208 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7208 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 208 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7209 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 420,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 38,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "Ordering number 7209 BECBP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 45 mm shaft, light (7200) series, with an open PA66-caged execution and one-direction axial capacity.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 2 is ISO diameter series 2 (light section), and the last two digits encode the 45 mm bore; the 85 mm OD and 19 mm width follow the ISO 15 general plan. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. As a CB execution the rings are delivered match-ready: face-to-face or back-to-back pairs can be assembled without regrinding, and Normal (CB) clearance suits general preloaded pairs — GA/GB/GC suffixes would denote factory-set light/medium preload. Speed planning uses two different ceilings: 9,500 r/min reference (thermal, under representative load) and 10,000 r/min limiting (mechanical cage/ball limit). Specify pairs rather than single units wherever thrust reverses: the 40° angle of 7209 generates an induced axial load under radial force, and an unpaired bearing on a reversing shaft will run slack in one direction and fret its seat.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "automotive and industrial transmissions"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "On this 45 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7209 pair heats, loses preload control and smears the raceways.",
      "The 72xx light section at 45 mm bore is the general-purpose angular-contact envelope (85×19 mm); stepping up to a 7309 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7209 mounting error.",
      "Do not mix execution classes inside one 7209 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Catalogue reference speed and limiting speed are different limits: the 9,500 r/min reference is a thermal criterion under load, while the 10,000 r/min limiting value is the mechanical ceiling — observe both.",
      "The 38/28.5 kN ratings are SKF catalogue 17000 values for the 7209 BECBP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7209 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7209 BECBP designation when purchasing and match the execution to the mounting arrangement.",
      "The CB execution (7209 BECBP) ships prepared for pair mounting but is not a matched set by itself: preload results from how the pair is clamped, so follow the SKF stand-off-ring and nut-torque procedure rather than assuming the bearings arrive preloaded."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7209?",
        "a": "The SKF 7209 BECBP is a single-row angular-contact ball bearing with 45 mm bore, 85 mm outer diameter and 19 mm width (1.772 × 3.346 × 0.748 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 38 kN, C0 28.5 kN, fatigue load limit Pu 1.22 kN, reference speed 9,500 r/min, limiting speed 10,000 r/min, mass about 420 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 9,500 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7209 bore code work?",
        "a": "The last two digits of 7209 are bore code 09, so 09 × 5 = 45 mm bore. The 85 mm OD and 19 mm width come from the ISO 15 diameter-series plan, shared with the 6209 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BECBP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. CB adds Normal axial clearance with ground faces for universal DB/DF/DT pair mounting. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7209 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7209 compare with a deep-groove 6209?",
        "a": "Both use the 45×85×19 mm ISO 15 envelope, but the angular-contact 7209 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7209 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6209",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6209-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6209-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7209 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7209 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7209 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7209 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7209 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7209 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 209 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7210 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 470,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 37.7,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7210 is SKF's single-row angular-contact ball bearing in the light (7200) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7210 BEP in the SKF Rolling Bearings catalogue.On the SKF nameplate, 7210 follows the ISO numbering convention: 7 for the angular-contact type, 2 for the light section section, final digits 10 for the 50 mm bore. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. The 1.22 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.76 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7210 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "belt-driven fan and blower shafts",
      "printing cylinders and packaging machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "On this 50 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7210 pair heats, loses preload control and smears the raceways.",
      "The 72xx light section at 50 mm bore is the general-purpose angular-contact envelope (90×20 mm); stepping up to a 7310 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7210 mounting error.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7210 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 37.7/28.5 kN ratings are SKF catalogue 17000 values for the 7210 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7210 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7210 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7210 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7210?",
        "a": "The SKF 7210 BEP is a single-row angular-contact ball bearing with 50 mm bore, 90 mm outer diameter and 20 mm width (1.969 × 3.543 × 0.787 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 37.7 kN, C0 28.5 kN, fatigue load limit Pu 1.22 kN, reference speed 9,000 r/min, limiting speed 8,500 r/min, mass about 470 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7210 bore code work?",
        "a": "The last two digits of 7210 are bore code 10, so 10 × 5 = 50 mm bore. The 90 mm OD and 20 mm width come from the ISO 15 diameter-series plan, shared with the 6210 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7210 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7210 compare with a deep-groove 6210?",
        "a": "Both use the 50×90×20 mm ISO 15 envelope, but the angular-contact 7210 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6210 cannot be dropped into a combined-load 7210 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6210",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6210-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6210-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7210 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7210 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7210 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7210 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7210 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7210 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7210 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 210 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7211 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 620,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 46.2,
    "static_load_kN": 36,
    "fatigue_load_limit_kN": 1.53,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "The SKF 7211 BEP is a 55×100×21 mm single-row angular-contact ball bearing — the light (7200) series of the SKF 7xxx line, built on the ISO 15 envelope shared with the 6211 deep-groove size but cut for combined radial and one-direction axial load.The code breaks down as type prefix 7 (angular contact), diameter series 2 (the light section), and bore code 11 = 55 mm; dimensions 55×100×21 mm therefore match the 6211 deep-groove envelope even though the internal design is different. Suffix letters after 7211 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. Selection arithmetic: the C0/C ratio is about 0.78 (static 36 kN against dynamic 46.2 kN), typical of a 40° angle sized for axial capacity, and the 1.53 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. A single 7211 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Mount the 55 mm bore 7211 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 55 mm bore is the general-purpose angular-contact envelope (100×21 mm); stepping up to a 7311 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7211 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "Do not mix execution classes inside one 7211 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "The 620 g mass and 21 mm width mean locknut and spacer faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the contact angle and concentrates load on one shoulder of 7211.",
      "The 46.2/36 kN ratings are SKF catalogue 17000 values for the 7211 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7211 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7211 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7211 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7211?",
        "a": "The SKF 7211 BEP is a single-row angular-contact ball bearing with 55 mm bore, 100 mm outer diameter and 21 mm width (2.165 × 3.937 × 0.827 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 46.2 kN, C0 36 kN, fatigue load limit Pu 1.53 kN, reference speed 8,000 r/min, limiting speed 7,500 r/min, mass about 620 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 7,500 r/min value is the one to design against."
      },
      {
        "q": "How does the 7211 bore code work?",
        "a": "The last two digits of 7211 are bore code 11, so 11 × 5 = 55 mm bore. The 100 mm OD and 21 mm width come from the ISO 15 diameter-series plan, shared with the 6211 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7211 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7211 compare with a deep-groove 6211?",
        "a": "Both use the 55×100×21 mm ISO 15 envelope, but the angular-contact 7211 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 46.2 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6211",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6211-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6211-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7211 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7211 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7211 BECBP shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7211 BECBPH shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7211 BECBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7211 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7211 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 211 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 211 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7212 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 800,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 57.2,
    "static_load_kN": 45.5,
    "fatigue_load_limit_kN": 1.93,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "In SKF catalogue PUB BU/P1 17000, 7212 appears as 7212 BEP: a 40° contact-angle, open, one-direction-thrust ball bearing in the light (7200) series, supplied with a glass-fibre PA66 cage as standard.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 2 is ISO diameter series 2 (light section), and the last two digits encode the 60 mm bore; the 110 mm OD and 22 mm width follow the ISO 15 general plan. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7212 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 25.0 mm radial section height ((110−60)/2) and 800 g catalogue mass frame a 60 mm bore bearing rated at 57.2 kN C — roughly 0.95 kN of dynamic capacity per millimetre of bore before application factors. Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7212 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 60 mm shaft positions.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "agricultural and construction machinery drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Mount the 60 mm bore 7212 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 60 mm bore is the general-purpose angular-contact envelope (110×22 mm); stepping up to a 7312 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7212 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7212 mounting error.",
      "Open 7212 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 57.2/45.5 kN ratings are SKF catalogue 17000 values for the 7212 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7212 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7212 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7212 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7212?",
        "a": "The SKF 7212 BEP is a single-row angular-contact ball bearing with 60 mm bore, 110 mm outer diameter and 22 mm width (2.362 × 4.331 × 0.866 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 57.2 kN, C0 45.5 kN, fatigue load limit Pu 1.93 kN, reference speed 7,000 r/min, limiting speed 7,000 r/min, mass about 800 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 7,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7212 bore code work?",
        "a": "The last two digits of 7212 are bore code 12, so 12 × 5 = 60 mm bore. The 110 mm OD and 22 mm width come from the ISO 15 diameter-series plan, shared with the 6212 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7212 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7212 compare with a deep-groove 6212?",
        "a": "Both use the 60×110×22 mm ISO 15 envelope, but the angular-contact 7212 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7212 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6212",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6212-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6212-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7212 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7212 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7212 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7212 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7212 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7212 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 212 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 212 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 212 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7213 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1000,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 66.3,
    "static_load_kN": 54,
    "fatigue_load_limit_kN": 2.28,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7213 BEP belongs to SKF's universal single-row angular-contact range — the 65 mm bore entry in the light (7200) series, dimensioned 120 mm OD and 23 mm wide to the same ISO 15 boundary plan as the 6213 deep-groove envelope.Digit by digit, 7213 reads as bearing type 7 (single-row angular contact), light section diameter series 2, and bore reference 13 resolving to 65 mm; 120 mm OD and 23 width are the matching ISO 15 boundary values. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Catalogue mass 1000 g for the 65×120×23 mm open execution covers the PA66 cage and standard ball complement; sealed or brass-cage variants of the same size differ slightly in mass and carry their own order numbers. Specify pairs rather than single units wherever thrust reverses: the 40° angle of 7213 generates an induced axial load under radial force, and an unpaired bearing on a reversing shaft will run slack in one direction and fret its seat.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "agricultural and construction machinery drives",
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "false brinelling on idle paired sets exposed to machine vibration",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount the 65 mm bore 7213 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 65 mm bore is the general-purpose angular-contact envelope (120×23 mm); stepping up to a 7313 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "A single 7213 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7213 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "Shaft and housing fillets must clear the bearing chamfer so the 23 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 66.3/54 kN ratings are SKF catalogue 17000 values for the 7213 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7213 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7213 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7213 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7213?",
        "a": "The SKF 7213 BEP is a single-row angular-contact ball bearing with 65 mm bore, 120 mm outer diameter and 23 mm width (2.559 × 4.724 × 0.906 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 66.3 kN, C0 54 kN, fatigue load limit Pu 2.28 kN, reference speed 6,700 r/min, limiting speed 6,300 r/min, mass about 1000 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7213 bore code work?",
        "a": "The last two digits of 7213 are bore code 13, so 13 × 5 = 65 mm bore. The 120 mm OD and 23 mm width come from the ISO 15 diameter-series plan, shared with the 6213 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7213 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7213 compare with a deep-groove 6213?",
        "a": "Both use the 65×120×23 mm ISO 15 envelope, but the angular-contact 7213 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6213 cannot be dropped into a combined-load 7213 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6213",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6213-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7213 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7213 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7213 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7213 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7213 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7213 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 213 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 213 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 213 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7214 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1100,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 67.6,
    "static_load_kN": 56,
    "fatigue_load_limit_kN": 2.36,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 70 mm shaft carrying combined load, SKF lists 7214 under catalogue execution 7214 BEP: one open single-row angular-contact ball bearing, 40° contact angle, in the light (7200) series of the 7xxx family.Numbering ties the bearing to its envelope: 7214 means angular-contact type 7, light section section 2, 70 mm bore — which is why the 125×24 mm outline swaps dimensionally with a 6214, though the load behaviour does not. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). At 6,300 r/min reference speed the 27.5 mm-section 7214 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 6,000 r/min as the mechanical ceiling. Because the contact line runs at 40°, one 7214 reacts thrust in a single direction; bidirectional shafts need a DB or DF pair with defined preload, and a rotating inner ring on a 70 mm shaft typically takes a k5 seat with an H7 housing bore.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Mount the 70 mm bore 7214 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 70 mm bore is the general-purpose angular-contact envelope (125×24 mm); stepping up to a 7314 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "At the 67.6 kN rating of 7214, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 6,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7214 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "Catalogue reference speed and limiting speed are different limits: the 6,300 r/min reference is a thermal criterion under load, while the 6,000 r/min limiting value is the mechanical ceiling — observe both.",
      "The 67.6/56 kN ratings are SKF catalogue 17000 values for the 7214 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7214 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7214 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7214 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7214?",
        "a": "The SKF 7214 BEP is a single-row angular-contact ball bearing with 70 mm bore, 125 mm outer diameter and 24 mm width (2.756 × 4.921 × 0.945 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 67.6 kN, C0 56 kN, fatigue load limit Pu 2.36 kN, reference speed 6,300 r/min, limiting speed 6,000 r/min, mass about 1100 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 6,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7214 bore code work?",
        "a": "The last two digits of 7214 are bore code 14, so 14 × 5 = 70 mm bore. The 125 mm OD and 24 mm width come from the ISO 15 diameter-series plan, shared with the 6214 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7214 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7214 compare with a deep-groove 6214?",
        "a": "Both use the 70×125×24 mm ISO 15 envelope, but the angular-contact 7214 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 67.6 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6214",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6214-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6214-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7214 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7214 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7214 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7214 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7214 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7214 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 214 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 214 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 214 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7215 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1200,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 70.2,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.5,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7215 (7215 BEP) is the light (7200) series angular-contact choice for a 75 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 130×25 mm ISO 15 envelope.On the SKF nameplate, 7215 follows the ISO numbering convention: 7 for the angular-contact type, 2 for the light section section, final digits 15 for the 75 mm bore. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. Speed planning uses two different ceilings: 6,000 r/min reference (thermal, under representative load) and 5,600 r/min limiting (mechanical cage/ball limit). For a 75 mm shaft the usual seat is k5 with an H7 housing when the inner ring rotates; arrange two 7215 bearings as a set for two-direction location and set preload from the load diagram, never from assembly feel.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Mount the 75 mm bore 7215 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 75 mm bore is the general-purpose angular-contact envelope (130×25 mm); stepping up to a 7315 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7215 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "A single 7215 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "The 7215 shares its ISO 15 envelope with deep-groove 6215 but is not a drop-in replacement: it cannot run effectively under pure radial load without a minimum axial load, and a deep-groove bearing cannot replace its combined-load duty.",
      "The 70.2/60 kN ratings are SKF catalogue 17000 values for the 7215 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7215 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7215 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7215 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7215?",
        "a": "The SKF 7215 BEP is a single-row angular-contact ball bearing with 75 mm bore, 130 mm outer diameter and 25 mm width (2.953 × 5.118 × 0.984 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 70.2 kN, C0 60 kN, fatigue load limit Pu 2.5 kN, reference speed 6,000 r/min, limiting speed 5,600 r/min, mass about 1200 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 6,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7215 bore code work?",
        "a": "The last two digits of 7215 are bore code 15, so 15 × 5 = 75 mm bore. The 130 mm OD and 25 mm width come from the ISO 15 diameter-series plan, shared with the 6215 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7215 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7215 compare with a deep-groove 6215?",
        "a": "Both use the 75×130×25 mm ISO 15 envelope, but the angular-contact 7215 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7215 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6215",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6215-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6215-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7215 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7215 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7215 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7215 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7215 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 215 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 215 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 215 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7216 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1450,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 80.6,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 2.8,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "Ordering number 7216 BEP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 80 mm shaft, light (7200) series, with an open PA66-caged execution and one-direction axial capacity.The code breaks down as type prefix 7 (angular contact), diameter series 2 (the light section), and bore code 16 = 80 mm; dimensions 80×140×26 mm therefore match the 6216 deep-groove envelope even though the internal design is different. Suffix letters after 7216 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. With C 80.6 kN and C0 69.5 kN, the 7216 pair-sizing check is dominated by the axial share: keep the equivalent load P below the rating at the required L10, remembering one bearing alone cannot cover reversing thrust at 5,300 r/min. Mounting practice for 7216: the rotating ring takes the interference fit (k5 on a 80 mm rotating shaft), the stationary ring slides for axial location, and reversing-thrust duty demands a paired DB/DF set rather than one bearing.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "agricultural and construction machinery drives",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount the 80 mm bore 7216 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 80 mm bore is the general-purpose angular-contact envelope (140×26 mm); stepping up to a 7316 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Do not mix execution classes inside one 7216 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "At the 80.6 kN rating of 7216, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 5,300 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the inner ring only, or brinell marks on the 140 mm race release as noise within the first running hours.",
      "The 80.6/69.5 kN ratings are SKF catalogue 17000 values for the 7216 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7216 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7216 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7216 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7216?",
        "a": "The SKF 7216 BEP is a single-row angular-contact ball bearing with 80 mm bore, 140 mm outer diameter and 26 mm width (3.15 × 5.512 × 1.024 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 80.6 kN, C0 69.5 kN, fatigue load limit Pu 2.8 kN, reference speed 5,600 r/min, limiting speed 5,300 r/min, mass about 1450 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7216 bore code work?",
        "a": "The last two digits of 7216 are bore code 16, so 16 × 5 = 80 mm bore. The 140 mm OD and 26 mm width come from the ISO 15 diameter-series plan, shared with the 6216 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7216 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7216 compare with a deep-groove 6216?",
        "a": "Both use the 80×140×26 mm ISO 15 envelope, but the angular-contact 7216 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6216 cannot be dropped into a combined-load 7216 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6216",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6216-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6216-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7216 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7216 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7216 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7216 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7216 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7216 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 216 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 216 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7217 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1850,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.25,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7217 is SKF's single-row angular-contact ball bearing in the light (7200) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7217 BEP in the SKF Rolling Bearings catalogue.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 2 is ISO diameter series 2 (light section), and the last two digits encode the 85 mm bore; the 150 mm OD and 28 mm width follow the ISO 15 general plan. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7217 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 3.25 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.87 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7217 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "agricultural and construction machinery drives",
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "pre-grease degradation after long shelf storage without rotation or re-greasing"
    ],
    "pitfalls": [
      "Mount the 85 mm bore 7217 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 85 mm bore is the general-purpose angular-contact envelope (150×28 mm); stepping up to a 7317 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7217 mounting error.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7217 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 95.6/83 kN ratings are SKF catalogue 17000 values for the 7217 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7217 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7217 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7217 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7217?",
        "a": "The SKF 7217 BEP is a single-row angular-contact ball bearing with 85 mm bore, 150 mm outer diameter and 28 mm width (3.346 × 5.906 × 1.102 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 95.6 kN, C0 83 kN, fatigue load limit Pu 3.25 kN, reference speed 5,300 r/min, limiting speed 5,000 r/min, mass about 1850 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 5,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7217 bore code work?",
        "a": "The last two digits of 7217 are bore code 17, so 17 × 5 = 85 mm bore. The 150 mm OD and 28 mm width come from the ISO 15 diameter-series plan, shared with the 6217 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7217 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7217 compare with a deep-groove 6217?",
        "a": "Both use the 85×150×28 mm ISO 15 envelope, but the angular-contact 7217 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 95.6 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6217",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6217-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6217-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7217 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7217 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7217 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7217 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-217-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 217 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-217-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 217 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7218 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 2300,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 108,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "The SKF 7218 BEP is a 90×160×30 mm single-row angular-contact ball bearing — the light (7200) series of the SKF 7xxx line, built on the ISO 15 envelope shared with the 6218 deep-groove size but cut for combined radial and one-direction axial load.Digit by digit, 7218 reads as bearing type 7 (single-row angular contact), light section diameter series 2, and bore reference 18 resolving to 90 mm; 160 mm OD and 30 width are the matching ISO 15 boundary values. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Selection arithmetic: the C0/C ratio is about 0.89 (static 96.5 kN against dynamic 108 kN), typical of a 40° angle sized for axial capacity, and the 3.65 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. A single 7218 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "mounting score marks when the bearing is cocked over the shaft keyway or a burr"
    ],
    "pitfalls": [
      "Mount the 90 mm bore 7218 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 72xx light section at 90 mm bore is the general-purpose angular-contact envelope (160×30 mm); stepping up to a 7318 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7218 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "Do not mix execution classes inside one 7218 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "The 2300 g mass and 30 mm width mean locknut and spacer faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the contact angle and concentrates load on one shoulder of 7218.",
      "The 108/96.5 kN ratings are SKF catalogue 17000 values for the 7218 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7218 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7218 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7218 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7218?",
        "a": "The SKF 7218 BEP is a single-row angular-contact ball bearing with 90 mm bore, 160 mm outer diameter and 30 mm width (3.543 × 6.299 × 1.181 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 108 kN, C0 96.5 kN, fatigue load limit Pu 3.65 kN, reference speed 5,000 r/min, limiting speed 4,500 r/min, mass about 2300 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 5,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7218 bore code work?",
        "a": "The last two digits of 7218 are bore code 18, so 18 × 5 = 90 mm bore. The 160 mm OD and 30 mm width come from the ISO 15 diameter-series plan, shared with the 6218 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7218 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7218 compare with a deep-groove 6218?",
        "a": "Both use the 90×160×30 mm ISO 15 envelope, but the angular-contact 7218 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7218 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6218",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6218-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6218-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7218-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7218 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7218-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7218 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7218-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7218 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7218-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7218 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-218-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 218 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7219 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 2700,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 124,
    "static_load_kN": 108,
    "fatigue_load_limit_kN": 4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "In SKF catalogue PUB BU/P1 17000, 7219 appears as 7219 BEP: a 40° contact-angle, open, one-direction-thrust ball bearing in the light (7200) series, supplied with a glass-fibre PA66 cage as standard.Numbering ties the bearing to its envelope: 7219 means angular-contact type 7, light section section 2, 95 mm bore — which is why the 170×32 mm outline swaps dimensionally with a 6219, though the load behaviour does not. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). The 37.5 mm radial section height ((170−95)/2) and 2700 g catalogue mass frame a 95 mm bore bearing rated at 124 kN C — roughly 1.31 kN of dynamic capacity per millimetre of bore before application factors. Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7219 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 95 mm shaft positions.",
    "applications": [
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "At 95 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 72xx light section at 95 mm bore is the general-purpose angular-contact envelope (170×32 mm); stepping up to a 7319 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7219 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7219 mounting error.",
      "Open 7219 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 124/108 kN ratings are SKF catalogue 17000 values for the 7219 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7219 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7219 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7219 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7219?",
        "a": "The SKF 7219 BEP is a single-row angular-contact ball bearing with 95 mm bore, 170 mm outer diameter and 32 mm width (3.74 × 6.693 × 1.26 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 124 kN, C0 108 kN, fatigue load limit Pu 4 kN, reference speed 4,500 r/min, limiting speed 4,300 r/min, mass about 2700 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7219 bore code work?",
        "a": "The last two digits of 7219 are bore code 19, so 19 × 5 = 95 mm bore. The 170 mm OD and 32 mm width come from the ISO 15 diameter-series plan, shared with the 6219 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7219 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7219 compare with a deep-groove 6219?",
        "a": "Both use the 95×170×32 mm ISO 15 envelope, but the angular-contact 7219 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6219 cannot be dropped into a combined-load 7219 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6219",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6219-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6219-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7219 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7219 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7219 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7219 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7219 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-219-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 219 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7220 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 3300,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 135,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7220 BEP belongs to SKF's universal single-row angular-contact range — the 100 mm bore entry in the light (7200) series, dimensioned 180 mm OD and 34 mm wide to the same ISO 15 boundary plan as the 6220 deep-groove envelope.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 2 is ISO diameter series 2 (light section), and the last two digits encode the 100 mm bore; the 180 mm OD and 34 mm width follow the ISO 15 general plan. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). At 4,300 r/min reference speed the 40.0 mm-section 7220 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 4,000 r/min as the mechanical ceiling. Mounting practice for 7220: the rotating ring takes the interference fit (k5 on a 100 mm rotating shaft), the stationary ring slides for axial location, and reversing-thrust duty demands a paired DB/DF set rather than one bearing.",
    "applications": [
      "large mud pumps and offshore winch drums",
      "heavy industrial gearboxes",
      "large process pumps and compressors",
      "marine propulsion and deck machinery"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "false brinelling on idle paired sets exposed to machine vibration",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "pre-grease degradation after long shelf storage without rotation or re-greasing"
    ],
    "pitfalls": [
      "At 100 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 72xx light section at 100 mm bore is the general-purpose angular-contact envelope (180×34 mm); stepping up to a 7320 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7220 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "Do not mix execution classes inside one 7220 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "The 7220 shares its ISO 15 envelope with deep-groove 6220 but is not a drop-in replacement: it cannot run effectively under pure radial load without a minimum axial load, and a deep-groove bearing cannot replace its combined-load duty.",
      "The 135/122 kN ratings are SKF catalogue 17000 values for the 7220 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7220 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7220 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7220 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7220?",
        "a": "The SKF 7220 BEP is a single-row angular-contact ball bearing with 100 mm bore, 180 mm outer diameter and 34 mm width (3.937 × 7.087 × 1.339 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 135 kN, C0 122 kN, fatigue load limit Pu 4.4 kN, reference speed 4,300 r/min, limiting speed 4,000 r/min, mass about 3300 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 4,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7220 bore code work?",
        "a": "The last two digits of 7220 are bore code 20, so 20 × 5 = 100 mm bore. The 180 mm OD and 34 mm width come from the ISO 15 diameter-series plan, shared with the 6220 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7220 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7220 compare with a deep-groove 6220?",
        "a": "Both use the 100×180×34 mm ISO 15 envelope, but the angular-contact 7220 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 135 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6220",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6220-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6220-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7220-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7220 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7220-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7220 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7220-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7220 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7220-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7220 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-220-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 220 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7221",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7221 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 3950,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 156,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 105 mm shaft carrying combined load, SKF lists 7221 under catalogue execution 7221 BECBP: one open single-row angular-contact ball bearing, 40° contact angle, in the light (7200) series of the 7xxx family.Digit by digit, 7221 reads as bearing type 7 (single-row angular contact), light section diameter series 2, and bore reference 21 resolving to 105 mm; 190 mm OD and 36 width are the matching ISO 15 boundary values. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. As a CB execution the rings are delivered match-ready: face-to-face or back-to-back pairs can be assembled without regrinding, and Normal (CB) clearance suits general preloaded pairs — GA/GB/GC suffixes would denote factory-set light/medium preload. Speed planning uses two different ceilings: 4,000 r/min reference (thermal, under representative load) and 4,300 r/min limiting (mechanical cage/ball limit). Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7221 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "large process pumps and compressors",
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "mounting score marks when the bearing is cocked over the shaft keyway or a burr"
    ],
    "pitfalls": [
      "At 105 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 72xx light section at 105 mm bore is the general-purpose angular-contact envelope (190×36 mm); stepping up to a 7321 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "A single 7221 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7221 mounting error.",
      "Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the inner ring only, or brinell marks on the 190 mm race release as noise within the first running hours.",
      "The 156/150 kN ratings are SKF catalogue 17000 values for the 7221 BECBP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7221 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7221 BECBP designation when purchasing and match the execution to the mounting arrangement.",
      "The CB execution (7221 BECBP) ships prepared for pair mounting but is not a matched set by itself: preload results from how the pair is clamped, so follow the SKF stand-off-ring and nut-torque procedure rather than assuming the bearings arrive preloaded."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7221?",
        "a": "The SKF 7221 BECBP is a single-row angular-contact ball bearing with 105 mm bore, 190 mm outer diameter and 36 mm width (4.134 × 7.48 × 1.417 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 156 kN, C0 150 kN, fatigue load limit Pu 5.2 kN, reference speed 4,000 r/min, limiting speed 4,300 r/min, mass about 3950 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 4,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7221 bore code work?",
        "a": "The last two digits of 7221 are bore code 21, so 21 × 5 = 105 mm bore. The 190 mm OD and 36 mm width come from the ISO 15 diameter-series plan, shared with the 6221 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BECBP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. CB adds Normal axial clearance with ground faces for universal DB/DF/DT pair mounting. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7221 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7221 compare with a deep-groove 6221?",
        "a": "Both use the 105×190×36 mm ISO 15 envelope, but the angular-contact 7221 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7221 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7221-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "6221",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6221-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7221-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7221 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7221-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7221 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7221 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7222 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 4600,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 153,
    "static_load_kN": 143,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7222 (7222 BEP) is the light (7200) series angular-contact choice for a 110 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 200×38 mm ISO 15 envelope.Numbering ties the bearing to its envelope: 7222 means angular-contact type 7, light section section 2, 110 mm bore — which is why the 200×38 mm outline swaps dimensionally with a 6222, though the load behaviour does not. Suffix letters after 7222 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. With C 153 kN and C0 143 kN, the 7222 pair-sizing check is dominated by the axial share: keep the equivalent load P below the rating at the required L10, remembering one bearing alone cannot cover reversing thrust at 3,600 r/min. A single 7222 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "At 110 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 72xx light section at 110 mm bore is the general-purpose angular-contact envelope (200×38 mm); stepping up to a 7322 changes OD, width and heat generation — it is not a drop-in swap when the housing and speed are fixed.",
      "At the 153 kN rating of 7222, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 3,600 r/min speed end and heavier preload only where moment stiffness dominates.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7222 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 153/143 kN ratings are SKF catalogue 17000 values for the 7222 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7222 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7222 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7222 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7222?",
        "a": "The SKF 7222 BEP is a single-row angular-contact ball bearing with 110 mm bore, 200 mm outer diameter and 38 mm width (4.331 × 7.874 × 1.496 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 153 kN, C0 143 kN, fatigue load limit Pu 4.9 kN, reference speed 4,000 r/min, limiting speed 3,600 r/min, mass about 4600 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7222 bore code work?",
        "a": "The last two digits of 7222 are bore code 22, so 22 × 5 = 110 mm bore. The 200 mm OD and 38 mm width come from the ISO 15 diameter-series plan, shared with the 6222 deep-groove envelope."
      },
      {
        "q": "What do the 72xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 2 is the ISO diameter series (light section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7222 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7222 compare with a deep-groove 6222?",
        "a": "Both use the 110×200×38 mm ISO 15 envelope, but the angular-contact 7222 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6222 cannot be dropped into a combined-load 7222 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6222",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6222-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6222-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7222-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7222 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7222-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7222 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7222-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7222 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7222-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7222 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-222-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 222 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7301",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7301 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 60,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 10.6,
    "static_load_kN": 5,
    "fatigue_load_limit_kN": 0.208,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7301 is SKF's single-row angular-contact ball bearing in the medium (7300) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7301 BEP in the SKF Rolling Bearings catalogue.Digit by digit, 7301 reads as bearing type 7 (single-row angular contact), medium section diameter series 3, and bore reference 01 resolving to 12 mm (codes 00-03 use the 10/12/15/17 mm exception table); 37 mm OD and 12 width are the matching ISO 15 boundary values. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. The 0.208 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.47 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7301 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 12 mm shaft positions.",
    "applications": [
      "instrument and rotary-table drives",
      "dental and laboratory high-speed rotors",
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "pre-grease degradation after long shelf storage without rotation or re-greasing"
    ],
    "pitfalls": [
      "At a 12 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7301 shows up as spindle vibration long before it fails.",
      "The 73xx medium section at 12 mm bore (37×12 mm) is heavier-rated than the 7201 but runs hotter at the same speed; do not substitute a 7301 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "A single 7301 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "Do not mix execution classes inside one 7301 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the inner ring only, or brinell marks on the 37 mm race release as noise within the first running hours.",
      "The 10.6/5 kN ratings are SKF catalogue 17000 values for the 7301 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7301 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7301 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7301 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7301?",
        "a": "The SKF 7301 BEP is a single-row angular-contact ball bearing with 12 mm bore, 37 mm outer diameter and 12 mm width (0.472 × 1.457 × 0.472 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 10.6 kN, C0 5 kN, fatigue load limit Pu 0.208 kN, reference speed 26,000 r/min, limiting speed 24,000 r/min, mass about 60 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 24,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7301 bore code work?",
        "a": "The last two digits of 7301 are bore code 01, giving a 12 mm bore under the exception table. The 37 mm OD and 12 mm width come from the ISO 15 diameter-series plan, shared with the 6301 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7301 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7301 compare with a deep-groove 6301?",
        "a": "Both use the 12×37×12 mm ISO 15 envelope, but the angular-contact 7301 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 10.6 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7301-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 12×37×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6301",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6301-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6301-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6301-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7301-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7301 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7301-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7301 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7301 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7302",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7302 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 80,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 13,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.28,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "The SKF 7302 BEP is a 15×42×13 mm single-row angular-contact ball bearing — the medium (7300) series of the SKF 7xxx line, built on the ISO 15 envelope shared with the 6302 deep-groove size but cut for combined radial and one-direction axial load.Numbering ties the bearing to its envelope: 7302 means angular-contact type 7, medium section section 3, 15 mm bore (codes 00-03 use the 10/12/15/17 mm exception table) — which is why the 42×13 mm outline swaps dimensionally with a 6302, though the load behaviour does not. Suffix letters after 7302 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. Selection arithmetic: the C0/C ratio is about 0.52 (static 6.7 kN against dynamic 13 kN), typical of a 40° angle sized for axial capacity, and the 0.28 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. Specify pairs rather than single units wherever thrust reverses: the 40° angle of 7302 generates an induced axial load under radial force, and an unpaired bearing on a reversing shaft will run slack in one direction and fret its seat.",
    "applications": [
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles",
      "small gear pumps and metering pumps"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "mounting score marks when the bearing is cocked over the shaft keyway or a burr"
    ],
    "pitfalls": [
      "At a 15 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7302 shows up as spindle vibration long before it fails.",
      "The 73xx medium section at 15 mm bore (42×13 mm) is heavier-rated than the 7202 but runs hotter at the same speed; do not substitute a 7302 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "At the 13 kN rating of 7302, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 20,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7302 mounting error.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 13/6.7 kN ratings are SKF catalogue 17000 values for the 7302 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7302 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7302 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7302 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7302?",
        "a": "The SKF 7302 BEP is a single-row angular-contact ball bearing with 15 mm bore, 42 mm outer diameter and 13 mm width (0.591 × 1.654 × 0.512 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 13 kN, C0 6.7 kN, fatigue load limit Pu 0.28 kN, reference speed 22,000 r/min, limiting speed 20,000 r/min, mass about 80 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 22,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7302 bore code work?",
        "a": "The last two digits of 7302 are bore code 02, giving a 15 mm bore under the exception table. The 42 mm OD and 13 mm width come from the ISO 15 diameter-series plan, shared with the 6302 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7302 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7302 compare with a deep-groove 6302?",
        "a": "Both use the 15×42×13 mm ISO 15 envelope, but the angular-contact 7302 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7302 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7302-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6302",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6302-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6302-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6302-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7302-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7302 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7302-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7302 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7302-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7302 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7302 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7303",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7303 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 110,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 8.3,
    "fatigue_load_limit_kN": 0.355,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "In SKF catalogue PUB BU/P1 17000, 7303 appears as 7303 BEP: a 40° contact-angle, open, one-direction-thrust ball bearing in the medium (7300) series, supplied with a glass-fibre PA66 cage as standard.On the SKF nameplate, 7303 follows the ISO numbering convention: 7 for the angular-contact type, 3 for the medium section section, final digits 03 for the 17 mm bore (codes 00-03 use the 10/12/15/17 mm exception table). The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7303 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 15.0 mm radial section height ((47−17)/2) and 110 g catalogue mass frame a 17 mm bore bearing rated at 15.9 kN C — roughly 0.94 kN of dynamic capacity per millimetre of bore before application factors. Because the contact line runs at 40°, one 7303 reacts thrust in a single direction; bidirectional shafts need a DB or DF pair with defined preload, and a rotating inner ring on a 17 mm shaft typically takes a j5 seat with an H7 housing bore.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear pumps and metering pumps",
      "encoder and resolver mountings",
      "instrument and rotary-table drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "At a 17 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7303 shows up as spindle vibration long before it fails.",
      "The 73xx medium section at 17 mm bore (47×14 mm) is heavier-rated than the 7203 but runs hotter at the same speed; do not substitute a 7303 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7303 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7303 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "The 110 g mass and 14 mm width mean locknut and spacer faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the contact angle and concentrates load on one shoulder of 7303.",
      "The 15.9/8.3 kN ratings are SKF catalogue 17000 values for the 7303 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7303 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7303 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7303 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7303?",
        "a": "The SKF 7303 BEP is a single-row angular-contact ball bearing with 17 mm bore, 47 mm outer diameter and 14 mm width (0.669 × 1.85 × 0.551 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 15.9 kN, C0 8.3 kN, fatigue load limit Pu 0.355 kN, reference speed 20,000 r/min, limiting speed 19,000 r/min, mass about 110 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7303 bore code work?",
        "a": "The last two digits of 7303 are bore code 03, giving a 17 mm bore under the exception table. The 47 mm OD and 14 mm width come from the ISO 15 diameter-series plan, shared with the 6303 deep-groove envelope. Codes 00–03 follow the 10/12/15/17 mm exception table."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7303 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7303 compare with a deep-groove 6303?",
        "a": "Both use the 17×47×14 mm ISO 15 envelope, but the angular-contact 7303 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6303 cannot be dropped into a combined-load 7303 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6303",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6303-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6303-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7303-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7303 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7303-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7303 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7303-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7303 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-303-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 303 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7303 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7304 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 140,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 17.4,
    "static_load_kN": 9.5,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7304 BEP belongs to SKF's universal single-row angular-contact range — the 20 mm bore entry in the medium (7300) series, dimensioned 52 mm OD and 15 mm wide to the same ISO 15 boundary plan as the 6304 deep-groove envelope.The code breaks down as type prefix 7 (angular contact), diameter series 3 (the medium section), and bore code 04 = 20 mm; dimensions 20×52×15 mm therefore match the 6304 deep-groove envelope even though the internal design is different. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Catalogue mass 140 g for the 20×52×15 mm open execution covers the PA66 cage and standard ball complement; sealed or brass-cage variants of the same size differ slightly in mass and carry their own order numbers. For a 20 mm shaft the usual seat is k5 with an H7 housing when the inner ring rotates; arrange two 7304 bearings as a set for two-direction location and set preload from the load diagram, never from assembly feel.",
    "applications": [
      "encoder and resolver mountings",
      "instrument and rotary-table drives",
      "dental and laboratory high-speed rotors",
      "small machine-tool spindles and high-speed heads"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "false brinelling on idle paired sets exposed to machine vibration",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "At a 20 mm bore the thin rings are easily distorted by an over-tight shaft nut; check seat runout (target Ra ≤ 0.8 µm) and torque the locknut progressively — a pinched 7304 shows up as spindle vibration long before it fails.",
      "The 73xx medium section at 20 mm bore (52×15 mm) is heavier-rated than the 7204 but runs hotter at the same speed; do not substitute a 7304 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "Do not mix execution classes inside one 7304 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7304 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "Open 7304 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 17.4/9.5 kN ratings are SKF catalogue 17000 values for the 7304 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7304 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7304 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7304 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7304?",
        "a": "The SKF 7304 BEP is a single-row angular-contact ball bearing with 20 mm bore, 52 mm outer diameter and 15 mm width (0.787 × 2.047 × 0.591 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 17.4 kN, C0 9.5 kN, fatigue load limit Pu 0.4 kN, reference speed 17,000 r/min, limiting speed 16,000 r/min, mass about 140 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 16,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7304 bore code work?",
        "a": "The last two digits of 7304 are bore code 04, so 04 × 5 = 20 mm bore. The 52 mm OD and 15 mm width come from the ISO 15 diameter-series plan, shared with the 6304 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7304 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7304 compare with a deep-groove 6304?",
        "a": "Both use the 20×52×15 mm ISO 15 envelope, but the angular-contact 7304 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 17.4 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6304",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6304-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6304-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6304-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7304 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7304 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7304 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7304 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7304 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7304 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7304 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 304 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 304 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 304 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7305 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 230,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 24.2,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.6,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 25 mm shaft carrying combined load, SKF lists 7305 under catalogue execution 7305 BEP: one open single-row angular-contact ball bearing, 40° contact angle, in the medium (7300) series of the 7xxx family.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 3 is ISO diameter series 3 (medium section), and the last two digits encode the 25 mm bore; the 62 mm OD and 17 mm width follow the ISO 15 general plan. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). At 14,000 r/min reference speed the 18.5 mm-section 7305 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 14,000 r/min as the mechanical ceiling. Mounting practice for 7305: the rotating ring takes the interference fit (k5 on a 25 mm rotating shaft), the stationary ring slides for axial location, and reversing-thrust duty demands a paired DB/DF set rather than one bearing.",
    "applications": [
      "printing cylinders and packaging machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "On this 25 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7305 pair heats, loses preload control and smears the raceways.",
      "The 73xx medium section at 25 mm bore (62×17 mm) is heavier-rated than the 7205 but runs hotter at the same speed; do not substitute a 7305 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7305 mounting error.",
      "A single 7305 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "Shaft and housing fillets must clear the bearing chamfer so the 17 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 24.2/14 kN ratings are SKF catalogue 17000 values for the 7305 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7305 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7305 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7305 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7305?",
        "a": "The SKF 7305 BEP is a single-row angular-contact ball bearing with 25 mm bore, 62 mm outer diameter and 17 mm width (0.984 × 2.441 × 0.669 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 24.2 kN, C0 14 kN, fatigue load limit Pu 0.6 kN, reference speed 14,000 r/min, limiting speed 14,000 r/min, mass about 230 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 14,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7305 bore code work?",
        "a": "The last two digits of 7305 are bore code 05, so 05 × 5 = 25 mm bore. The 62 mm OD and 17 mm width come from the ISO 15 diameter-series plan, shared with the 6305 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7305 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7305 compare with a deep-groove 6305?",
        "a": "Both use the 25×62×17 mm ISO 15 envelope, but the angular-contact 7305 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7305 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6305",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6305-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6305-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6305-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BEY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7305 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7305 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 305 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 305 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7306 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 340,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 19.3,
    "fatigue_load_limit_kN": 0.815,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7306 (7306 BEP) is the medium (7300) series angular-contact choice for a 30 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 72×19 mm ISO 15 envelope.Digit by digit, 7306 reads as bearing type 7 (single-row angular contact), medium section diameter series 3, and bore reference 06 resolving to 30 mm; 72 mm OD and 19 width are the matching ISO 15 boundary values. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. Speed planning uses two different ceilings: 12,000 r/min reference (thermal, under representative load) and 12,000 r/min limiting (mechanical cage/ball limit) — for this size the catalogue lists them at the same value. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7306 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "automotive and industrial transmissions"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "On this 30 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7306 pair heats, loses preload control and smears the raceways.",
      "The 73xx medium section at 30 mm bore (72×19 mm) is heavier-rated than the 7206 but runs hotter at the same speed; do not substitute a 7306 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7306 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "At the 32.5 kN rating of 7306, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 12,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Catalogue reference speed and limiting speed are different limits: the 12,000 r/min reference is a thermal criterion under load, while the 12,000 r/min limiting value is the mechanical ceiling — observe both.",
      "The 32.5/19.3 kN ratings are SKF catalogue 17000 values for the 7306 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7306 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7306 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7306 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7306?",
        "a": "The SKF 7306 BEP is a single-row angular-contact ball bearing with 30 mm bore, 72 mm outer diameter and 19 mm width (1.181 × 2.835 × 0.748 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 32.5 kN, C0 19.3 kN, fatigue load limit Pu 0.815 kN, reference speed 12,000 r/min, limiting speed 12,000 r/min, mass about 340 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7306 bore code work?",
        "a": "The last two digits of 7306 are bore code 06, so 06 × 5 = 30 mm bore. The 72 mm OD and 19 mm width come from the ISO 15 diameter-series plan, shared with the 6306 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7306 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7306 compare with a deep-groove 6306?",
        "a": "Both use the 30×72×19 mm ISO 15 envelope, but the angular-contact 7306 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6306 cannot be dropped into a combined-load 7306 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6306",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6306-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6306-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6306-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7306 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7306 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7306 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7306 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7306 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7306 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7306 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 306 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 306 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 306 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7307 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 450,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 39,
    "static_load_kN": 24.5,
    "fatigue_load_limit_kN": 1.04,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "Ordering number 7307 BEP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 35 mm shaft, medium (7300) series, with an open PA66-caged execution and one-direction axial capacity.Numbering ties the bearing to its envelope: 7307 means angular-contact type 7, medium section section 3, 35 mm bore — which is why the 80×21 mm outline swaps dimensionally with a 6307, though the load behaviour does not. Suffix letters after 7307 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. With C 39 kN and C0 24.5 kN, the 7307 pair-sizing check is dominated by the axial share: keep the equivalent load P below the rating at the required L10, remembering one bearing alone cannot cover reversing thrust at 10,000 r/min. A single 7307 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "centrifugal and vacuum pumps",
      "automotive and industrial transmissions",
      "belt-driven fan and blower shafts",
      "printing cylinders and packaging machine shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "On this 35 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7307 pair heats, loses preload control and smears the raceways.",
      "The 73xx medium section at 35 mm bore (80×21 mm) is heavier-rated than the 7207 but runs hotter at the same speed; do not substitute a 7307 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7307 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7307 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "The 7307 shares its ISO 15 envelope with deep-groove 6307 but is not a drop-in replacement: it cannot run effectively under pure radial load without a minimum axial load, and a deep-groove bearing cannot replace its combined-load duty.",
      "The 39/24.5 kN ratings are SKF catalogue 17000 values for the 7307 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7307 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7307 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7307 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7307?",
        "a": "The SKF 7307 BEP is a single-row angular-contact ball bearing with 35 mm bore, 80 mm outer diameter and 21 mm width (1.378 × 3.15 × 0.827 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 39 kN, C0 24.5 kN, fatigue load limit Pu 1.04 kN, reference speed 11,000 r/min, limiting speed 10,000 r/min, mass about 450 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 10,000 r/min value is the one to design against."
      },
      {
        "q": "How does the 7307 bore code work?",
        "a": "The last two digits of 7307 are bore code 07, so 07 × 5 = 35 mm bore. The 80 mm OD and 21 mm width come from the ISO 15 diameter-series plan, shared with the 6307 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7307 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7307 compare with a deep-groove 6307?",
        "a": "Both use the 35×80×21 mm ISO 15 envelope, but the angular-contact 7307 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 39 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6307",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6307-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6307-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7307 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7307 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7307 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7307 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7307 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7307 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7307 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 307 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 307 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 307 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7308 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 620,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 46.2,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 1.29,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7308 is SKF's single-row angular-contact ball bearing in the medium (7300) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7308 BEP in the SKF Rolling Bearings catalogue.On the SKF nameplate, 7308 follows the ISO numbering convention: 7 for the angular-contact type, 3 for the medium section section, final digits 08 for the 40 mm bore. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7308 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 1.29 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.66 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7308 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 40 mm shaft positions.",
    "applications": [
      "belt-driven fan and blower shafts",
      "printing cylinders and packaging machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "On this 40 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7308 pair heats, loses preload control and smears the raceways.",
      "The 73xx medium section at 40 mm bore (90×23 mm) is heavier-rated than the 7208 but runs hotter at the same speed; do not substitute a 7308 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "A single 7308 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "Do not mix execution classes inside one 7308 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the inner ring only, or brinell marks on the 90 mm race release as noise within the first running hours.",
      "The 46.2/30.5 kN ratings are SKF catalogue 17000 values for the 7308 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7308 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7308 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7308 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7308?",
        "a": "The SKF 7308 BEP is a single-row angular-contact ball bearing with 40 mm bore, 90 mm outer diameter and 23 mm width (1.575 × 3.543 × 0.906 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 46.2 kN, C0 30.5 kN, fatigue load limit Pu 1.29 kN, reference speed 9,500 r/min, limiting speed 9,000 r/min, mass about 620 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 9,500 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7308 bore code work?",
        "a": "The last two digits of 7308 are bore code 08, so 08 × 5 = 40 mm bore. The 90 mm OD and 23 mm width come from the ISO 15 diameter-series plan, shared with the 6308 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7308 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7308 compare with a deep-groove 6308?",
        "a": "Both use the 40×90×23 mm ISO 15 envelope, but the angular-contact 7308 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7308 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6308",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6308-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6308-RSR",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6308-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7308 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7308 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7308 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7308 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7308 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7308 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7308 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 308 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 308 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 308 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7309 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 820,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 55.9,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.6,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "The SKF 7309 BEP is a 45×100×25 mm single-row angular-contact ball bearing — the medium (7300) series of the SKF 7xxx line, built on the ISO 15 envelope shared with the 6309 deep-groove size but cut for combined radial and one-direction axial load.The code breaks down as type prefix 7 (angular contact), diameter series 3 (the medium section), and bore code 09 = 45 mm; dimensions 45×100×25 mm therefore match the 6309 deep-groove envelope even though the internal design is different. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Selection arithmetic: the C0/C ratio is about 0.67 (static 37.5 kN against dynamic 55.9 kN), typical of a 40° angle sized for axial capacity, and the 1.6 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. Specify pairs rather than single units wherever thrust reverses: the 40° angle of 7309 generates an induced axial load under radial force, and an unpaired bearing on a reversing shaft will run slack in one direction and fret its seat.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "On this 45 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7309 pair heats, loses preload control and smears the raceways.",
      "The 73xx medium section at 45 mm bore (100×25 mm) is heavier-rated than the 7209 but runs hotter at the same speed; do not substitute a 7309 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "At the 55.9 kN rating of 7309, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 8,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7309 mounting error.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 55.9/37.5 kN ratings are SKF catalogue 17000 values for the 7309 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7309 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7309 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7309 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7309?",
        "a": "The SKF 7309 BEP is a single-row angular-contact ball bearing with 45 mm bore, 100 mm outer diameter and 25 mm width (1.772 × 3.937 × 0.984 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 55.9 kN, C0 37.5 kN, fatigue load limit Pu 1.6 kN, reference speed 8,500 r/min, limiting speed 8,000 r/min, mass about 820 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7309 bore code work?",
        "a": "The last two digits of 7309 are bore code 09, so 09 × 5 = 45 mm bore. The 100 mm OD and 25 mm width come from the ISO 15 diameter-series plan, shared with the 6309 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7309 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7309 compare with a deep-groove 6309?",
        "a": "Both use the 45×100×25 mm ISO 15 envelope, but the angular-contact 7309 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6309 cannot be dropped into a combined-load 7309 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6309",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6309-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6309-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7309 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7309 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7309 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7309 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7309 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7309 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7309 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 309 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 309 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 309 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 309 PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7310 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1100,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 75,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "In SKF catalogue PUB BU/P1 17000, 7310 appears as 7310 BECBP: a 40° contact-angle, open, one-direction-thrust ball bearing in the medium (7300) series, supplied with a glass-fibre PA66 cage as standard.Numbering ties the bearing to its envelope: 7310 means angular-contact type 7, medium section section 3, 50 mm bore — which is why the 110×27 mm outline swaps dimensionally with a 6310, though the load behaviour does not. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. CB means the side faces are ground for universal matching with Normal internal axial clearance, which is the starting point for field-set preload rather than a factory-matched fixed-preload set. Catalogue mass 1100 g for the 50×110×27 mm open execution covers the PA66 cage and standard ball complement; sealed or brass-cage variants of the same size differ slightly in mass and carry their own order numbers. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7310 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "automotive and industrial transmissions",
      "belt-driven fan and blower shafts",
      "printing cylinders and packaging machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "On this 50 mm bore, interference and temperature rise consume clearance inside a preloaded pair; calculate the residual clearance after mounting and at operating temperature — an over-tight 7310 pair heats, loses preload control and smears the raceways.",
      "The 73xx medium section at 50 mm bore (110×27 mm) is heavier-rated than the 7210 but runs hotter at the same speed; do not substitute a 7310 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "At the 75 kN rating of 7310, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 8,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Do not mix execution classes inside one 7310 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Shaft and housing fillets must clear the bearing chamfer so the 27 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 75/51 kN ratings are SKF catalogue 17000 values for the 7310 BECBP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7310 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7310 BECBP designation when purchasing and match the execution to the mounting arrangement.",
      "The CB execution (7310 BECBP) ships prepared for pair mounting but is not a matched set by itself: preload results from how the pair is clamped, so follow the SKF stand-off-ring and nut-torque procedure rather than assuming the bearings arrive preloaded."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7310?",
        "a": "The SKF 7310 BECBP is a single-row angular-contact ball bearing with 50 mm bore, 110 mm outer diameter and 27 mm width (1.969 × 4.331 × 1.063 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 75 kN, C0 51 kN, fatigue load limit Pu 2.16 kN, reference speed 7,500 r/min, limiting speed 8,000 r/min, mass about 1100 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 7,500 r/min value is the one to design against."
      },
      {
        "q": "How does the 7310 bore code work?",
        "a": "The last two digits of 7310 are bore code 10, so 10 × 5 = 50 mm bore. The 110 mm OD and 27 mm width come from the ISO 15 diameter-series plan, shared with the 6310 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BECBP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. CB adds Normal axial clearance with ground faces for universal DB/DF/DT pair mounting. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7310 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7310 compare with a deep-groove 6310?",
        "a": "Both use the 50×110×27 mm ISO 15 envelope, but the angular-contact 7310 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 75 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "6310",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6310-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6310-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7310 BE-2RZP (glass-fibre PA66 cage, non-contact NBR seals (-2RZ)) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7310 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7310 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7310 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7310 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7310 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 310 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 310 PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7311 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1400,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 79.3,
    "static_load_kN": 55,
    "fatigue_load_limit_kN": 2.32,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7311 BEP belongs to SKF's universal single-row angular-contact range — the 55 mm bore entry in the medium (7300) series, dimensioned 120 mm OD and 29 mm wide to the same ISO 15 boundary plan as the 6311 deep-groove envelope.On the SKF nameplate, 7311 follows the ISO numbering convention: 7 for the angular-contact type, 3 for the medium section section, final digits 11 for the 55 mm bore. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). At 7,000 r/min reference speed the 32.5 mm-section 7311 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 6,700 r/min as the mechanical ceiling. A single 7311 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "false brinelling on idle paired sets exposed to machine vibration",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Mount the 55 mm bore 7311 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 55 mm bore (120×29 mm) is heavier-rated than the 7211 but runs hotter at the same speed; do not substitute a 7311 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7311 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7311 mounting error.",
      "Catalogue reference speed and limiting speed are different limits: the 7,000 r/min reference is a thermal criterion under load, while the 6,700 r/min limiting value is the mechanical ceiling — observe both.",
      "The 79.3/55 kN ratings are SKF catalogue 17000 values for the 7311 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7311 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7311 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7311 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7311?",
        "a": "The SKF 7311 BEP is a single-row angular-contact ball bearing with 55 mm bore, 120 mm outer diameter and 29 mm width (2.165 × 4.724 × 1.142 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 79.3 kN, C0 55 kN, fatigue load limit Pu 2.32 kN, reference speed 7,000 r/min, limiting speed 6,700 r/min, mass about 1400 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 7,000 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7311 bore code work?",
        "a": "The last two digits of 7311 are bore code 11, so 11 × 5 = 55 mm bore. The 120 mm OD and 29 mm width come from the ISO 15 diameter-series plan, shared with the 6311 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7311 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7311 compare with a deep-groove 6311?",
        "a": "Both use the 55×120×29 mm ISO 15 envelope, but the angular-contact 7311 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7311 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6311",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6311-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6311-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7311 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7311 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7311 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7311 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7311 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7311 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 311 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 311 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7312 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 1750,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 3,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 60 mm shaft carrying combined load, SKF lists 7312 under catalogue execution 7312 BEP: one open single-row angular-contact ball bearing, 40° contact angle, in the medium (7300) series of the 7xxx family.The code breaks down as type prefix 7 (angular contact), diameter series 3 (the medium section), and bore code 12 = 60 mm; dimensions 60×130×31 mm therefore match the 6312 deep-groove envelope even though the internal design is different. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. Speed planning uses two different ceilings: 6,300 r/min reference (thermal, under representative load) and 6,000 r/min limiting (mechanical cage/ball limit). Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7312 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 60 mm shaft positions.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Mount the 60 mm bore 7312 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 60 mm bore (130×31 mm) is heavier-rated than the 7212 but runs hotter at the same speed; do not substitute a 7312 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "Do not mix execution classes inside one 7312 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7312 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "The 7312 shares its ISO 15 envelope with deep-groove 6312 but is not a drop-in replacement: it cannot run effectively under pure radial load without a minimum axial load, and a deep-groove bearing cannot replace its combined-load duty.",
      "The 95.6/69.5 kN ratings are SKF catalogue 17000 values for the 7312 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7312 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7312 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7312 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7312?",
        "a": "The SKF 7312 BEP is a single-row angular-contact ball bearing with 60 mm bore, 130 mm outer diameter and 31 mm width (2.362 × 5.118 × 1.22 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 95.6 kN, C0 69.5 kN, fatigue load limit Pu 3 kN, reference speed 6,300 r/min, limiting speed 6,000 r/min, mass about 1750 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7312 bore code work?",
        "a": "The last two digits of 7312 are bore code 12, so 12 × 5 = 60 mm bore. The 130 mm OD and 31 mm width come from the ISO 15 diameter-series plan, shared with the 6312 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7312 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7312 compare with a deep-groove 6312?",
        "a": "Both use the 60×130×31 mm ISO 15 envelope, but the angular-contact 7312 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6312 cannot be dropped into a combined-load 7312 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6312",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6312-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6312-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7312 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7312 BECBP shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7312 BECBPH shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7312 BECBY shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7312 BECBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7312 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 312 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 312 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 312 PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7313 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 2150,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 108,
    "static_load_kN": 80,
    "fatigue_load_limit_kN": 3.35,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7313 (7313 BEP) is the medium (7300) series angular-contact choice for a 65 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 140×33 mm ISO 15 envelope.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 3 is ISO diameter series 3 (medium section), and the last two digits encode the 65 mm bore; the 140 mm OD and 33 mm width follow the ISO 15 general plan. Suffix letters after 7313 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. With C 108 kN and C0 80 kN, the 7313 pair-sizing check is dominated by the axial share: keep the equivalent load P below the rating at the required L10, remembering one bearing alone cannot cover reversing thrust at 5,600 r/min. Specify pairs rather than single units wherever thrust reverses: the 40° angle of 7313 generates an induced axial load under radial force, and an unpaired bearing on a reversing shaft will run slack in one direction and fret its seat.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "agricultural and construction machinery drives",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "pre-grease degradation after long shelf storage without rotation or re-greasing"
    ],
    "pitfalls": [
      "Mount the 65 mm bore 7313 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 65 mm bore (140×33 mm) is heavier-rated than the 7213 but runs hotter at the same speed; do not substitute a 7313 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7313 mounting error.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7313 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "Never press both rings through the wrong element during fitting: force for an interference shaft seat goes through the inner ring only, or brinell marks on the 140 mm race release as noise within the first running hours.",
      "The 108/80 kN ratings are SKF catalogue 17000 values for the 7313 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7313 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7313 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7313 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7313?",
        "a": "The SKF 7313 BEP is a single-row angular-contact ball bearing with 65 mm bore, 140 mm outer diameter and 33 mm width (2.559 × 5.512 × 1.299 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 108 kN, C0 80 kN, fatigue load limit Pu 3.35 kN, reference speed 6,000 r/min, limiting speed 5,600 r/min, mass about 2150 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 5,600 r/min value is the one to design against."
      },
      {
        "q": "How does the 7313 bore code work?",
        "a": "The last two digits of 7313 are bore code 13, so 13 × 5 = 65 mm bore. The 140 mm OD and 33 mm width come from the ISO 15 diameter-series plan, shared with the 6313 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7313 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7313 compare with a deep-groove 6313?",
        "a": "Both use the 65×140×33 mm ISO 15 envelope, but the angular-contact 7313 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 108 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6313",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6313-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6313-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7313 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7313 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7313 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7313 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7313 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7313 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 313 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 313 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7314 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 2650,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 119,
    "static_load_kN": 90,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "Ordering number 7314 BEP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 70 mm shaft, medium (7300) series, with an open PA66-caged execution and one-direction axial capacity.Digit by digit, 7314 reads as bearing type 7 (single-row angular contact), medium section diameter series 3, and bore reference 14 resolving to 70 mm; 150 mm OD and 35 width are the matching ISO 15 boundary values. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7314 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 3.65 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.76 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Because the contact line runs at 40°, one 7314 reacts thrust in a single direction; bidirectional shafts need a DB or DF pair with defined preload, and a rotating inner ring on a 70 mm shaft typically takes a k5 seat with an H7 housing bore.",
    "applications": [
      "agricultural and construction machinery drives",
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "mounting score marks when the bearing is cocked over the shaft keyway or a burr"
    ],
    "pitfalls": [
      "Mount the 70 mm bore 7314 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 70 mm bore (150×35 mm) is heavier-rated than the 7214 but runs hotter at the same speed; do not substitute a 7314 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7314 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "A single 7314 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.",
      "The 119/90 kN ratings are SKF catalogue 17000 values for the 7314 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7314 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7314 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7314 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7314?",
        "a": "The SKF 7314 BEP is a single-row angular-contact ball bearing with 70 mm bore, 150 mm outer diameter and 35 mm width (2.756 × 5.906 × 1.378 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 119 kN, C0 90 kN, fatigue load limit Pu 3.65 kN, reference speed 5,600 r/min, limiting speed 5,300 r/min, mass about 2650 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 5,600 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7314 bore code work?",
        "a": "The last two digits of 7314 are bore code 14, so 14 × 5 = 70 mm bore. The 150 mm OD and 35 mm width come from the ISO 15 diameter-series plan, shared with the 6314 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7314 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7314 compare with a deep-groove 6314?",
        "a": "Both use the 70×150×35 mm ISO 15 envelope, but the angular-contact 7314 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7314 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6314",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6314-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6314-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7314 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7314 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7314 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7314 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7314 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7314 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF 7314 ACCBM shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 314 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 314 MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 314 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7315 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 3200,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 125,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.8,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7315 is SKF's single-row angular-contact ball bearing in the medium (7300) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7315 BEP in the SKF Rolling Bearings catalogue.Numbering ties the bearing to its envelope: 7315 means angular-contact type 7, medium section section 3, 75 mm bore — which is why the 160×37 mm outline swaps dimensionally with a 6315, though the load behaviour does not. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Selection arithmetic: the C0/C ratio is about 0.78 (static 98 kN against dynamic 125 kN), typical of a 40° angle sized for axial capacity, and the 3.8 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. For a 75 mm shaft the usual seat is k5 with an H7 housing when the inner ring rotates; arrange two 7315 bearings as a set for two-direction location and set preload from the load diagram, never from assembly feel.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Mount the 75 mm bore 7315 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 75 mm bore (160×37 mm) is heavier-rated than the 7215 but runs hotter at the same speed; do not substitute a 7315 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7315 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "At the 125 kN rating of 7315, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 5,000 r/min speed end and heavier preload only where moment stiffness dominates.",
      "The 3200 g mass and 37 mm width mean locknut and spacer faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the contact angle and concentrates load on one shoulder of 7315.",
      "The 125/98 kN ratings are SKF catalogue 17000 values for the 7315 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7315 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7315 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7315 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7315?",
        "a": "The SKF 7315 BEP is a single-row angular-contact ball bearing with 75 mm bore, 160 mm outer diameter and 37 mm width (2.953 × 6.299 × 1.457 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 125 kN, C0 98 kN, fatigue load limit Pu 3.8 kN, reference speed 5,300 r/min, limiting speed 5,000 r/min, mass about 3200 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7315 bore code work?",
        "a": "The last two digits of 7315 are bore code 15, so 15 × 5 = 75 mm bore. The 160 mm OD and 37 mm width come from the ISO 15 diameter-series plan, shared with the 6315 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7315 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7315 compare with a deep-groove 6315?",
        "a": "Both use the 75×160×37 mm ISO 15 envelope, but the angular-contact 7315 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6315 cannot be dropped into a combined-load 7315 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6315",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6315-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6315-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7315 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7315 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7315 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7315 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7315 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 315 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 315 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7316 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 3800,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 135,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "The SKF 7316 BEP is a 80×170×39 mm single-row angular-contact ball bearing — the medium (7300) series of the SKF 7xxx line, built on the ISO 15 envelope shared with the 6316 deep-groove size but cut for combined radial and one-direction axial load.On the SKF nameplate, 7316 follows the ISO numbering convention: 7 for the angular-contact type, 3 for the medium section section, final digits 16 for the 80 mm bore. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). The 45.0 mm radial section height ((170−80)/2) and 3800 g catalogue mass frame a 80 mm bore bearing rated at 135 kN C — roughly 1.69 kN of dynamic capacity per millimetre of bore before application factors. Mounting practice for 7316: the rotating ring takes the interference fit (k5 on a 80 mm rotating shaft), the stationary ring slides for axial location, and reversing-thrust duty demands a paired DB/DF set rather than one bearing.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "agricultural and construction machinery drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Mount the 80 mm bore 7316 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 80 mm bore (170×39 mm) is heavier-rated than the 7216 but runs hotter at the same speed; do not substitute a 7316 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "A single 7316 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7316 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "Open 7316 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 135/110 kN ratings are SKF catalogue 17000 values for the 7316 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7316 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7316 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7316 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7316?",
        "a": "The SKF 7316 BEP is a single-row angular-contact ball bearing with 80 mm bore, 170 mm outer diameter and 39 mm width (3.15 × 6.693 × 1.535 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 135 kN, C0 110 kN, fatigue load limit Pu 4.15 kN, reference speed 5,000 r/min, limiting speed 4,500 r/min, mass about 3800 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 4,500 r/min value is the one to design against."
      },
      {
        "q": "How does the 7316 bore code work?",
        "a": "The last two digits of 7316 are bore code 16, so 16 × 5 = 80 mm bore. The 170 mm OD and 39 mm width come from the ISO 15 diameter-series plan, shared with the 6316 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7316 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7316 compare with a deep-groove 6316?",
        "a": "Both use the 80×170×39 mm ISO 15 envelope, but the angular-contact 7316 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 135 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6316",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6316-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6316-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7316 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7316 BEM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7316 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7316 BECBPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7316 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7316 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 316 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 316 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7317 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 4450,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 146,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "In SKF catalogue PUB BU/P1 17000, 7317 appears as 7317 BEP: a 40° contact-angle, open, one-direction-thrust ball bearing in the medium (7300) series, supplied with a glass-fibre PA66 cage as standard.The code breaks down as type prefix 7 (angular contact), diameter series 3 (the medium section), and bore code 17 = 85 mm; dimensions 85×180×41 mm therefore match the 6317 deep-groove envelope even though the internal design is different. Here B marks the steep 40° contact angle (the highest-capacity single-row angle), E the modernised internal geometry and P the glass-fibre nylon cage; the same bare size in a 25° A-angle or brass M-cage execution carries a different suffix. Catalogue mass 4450 g for the 85×180×41 mm open execution covers the PA66 cage and standard ball complement; sealed or brass-cage variants of the same size differ slightly in mass and carry their own order numbers. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7317 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "agricultural and construction machinery drives",
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Mount the 85 mm bore 7317 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 85 mm bore (180×41 mm) is heavier-rated than the 7217 but runs hotter at the same speed; do not substitute a 7317 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "At the 146 kN rating of 7317, preload class changes stiffness by tens of percent but also heat generation; select light preload for the 4,300 r/min speed end and heavier preload only where moment stiffness dominates.",
      "Do not mix execution classes inside one 7317 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "Shaft and housing fillets must clear the bearing chamfer so the 41 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 146/122 kN ratings are SKF catalogue 17000 values for the 7317 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7317 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7317 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7317 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7317?",
        "a": "The SKF 7317 BEP is a single-row angular-contact ball bearing with 85 mm bore, 180 mm outer diameter and 41 mm width (3.346 × 7.087 × 1.614 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 146 kN, C0 122 kN, fatigue load limit Pu 4.5 kN, reference speed 4,500 r/min, limiting speed 4,300 r/min, mass about 4450 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 4,500 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7317 bore code work?",
        "a": "The last two digits of 7317 are bore code 17, so 17 × 5 = 85 mm bore. The 180 mm OD and 41 mm width come from the ISO 15 diameter-series plan, shared with the 6317 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7317 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7317 compare with a deep-groove 6317?",
        "a": "Both use the 85×180×41 mm ISO 15 envelope, but the angular-contact 7317 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7317 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6317",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6317-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6317-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7317 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7317 BEM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7317 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7317 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7317 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7317 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 317 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7318 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 5200,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 156,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.8,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7318 BEP belongs to SKF's universal single-row angular-contact range — the 90 mm bore entry in the medium (7300) series, dimensioned 190 mm OD and 43 mm wide to the same ISO 15 boundary plan as the 6318 deep-groove envelope.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 3 is ISO diameter series 3 (medium section), and the last two digits encode the 90 mm bore; the 190 mm OD and 43 mm width follow the ISO 15 general plan. Suffix letters after 7318 describe the build: B fixes the 40° contact angle, E denotes the reinforced internal geometry, and P identifies the moulded PA66 glass-fibre cage rather than a stamped-steel or machined-brass one. At 4,300 r/min reference speed the 50.0 mm-section 7318 is governed thermally by preload and lubricant flow; oil-air or grease pack selection should be made against that value, with 4,000 r/min as the mechanical ceiling. A single 7318 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "false brinelling on idle paired sets exposed to machine vibration",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount the 90 mm bore 7318 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.",
      "The 73xx medium section at 90 mm bore (190×43 mm) is heavier-rated than the 7218 but runs hotter at the same speed; do not substitute a 7318 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "When the outer ring rotates, reverse the fit logic and provide outer-ring location; the steep 40° contact of 7318 pushes the rings apart under load, so a non-located outer ring walks its seat even when the shaft is fixed.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7318 mounting error.",
      "Catalogue reference speed and limiting speed are different limits: the 4,300 r/min reference is a thermal criterion under load, while the 4,000 r/min limiting value is the mechanical ceiling — observe both.",
      "The 156/134 kN ratings are SKF catalogue 17000 values for the 7318 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7318 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7318 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7318 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7318?",
        "a": "The SKF 7318 BEP is a single-row angular-contact ball bearing with 90 mm bore, 190 mm outer diameter and 43 mm width (3.543 × 7.48 × 1.693 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 156 kN, C0 134 kN, fatigue load limit Pu 4.8 kN, reference speed 4,300 r/min, limiting speed 4,000 r/min, mass about 5200 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7318 bore code work?",
        "a": "The last two digits of 7318 are bore code 18, so 18 × 5 = 90 mm bore. The 190 mm OD and 43 mm width come from the ISO 15 diameter-series plan, shared with the 6318 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7318 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7318 compare with a deep-groove 6318?",
        "a": "Both use the 90×190×43 mm ISO 15 envelope, but the angular-contact 7318 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6318 cannot be dropped into a combined-load 7318 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6318",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6318-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6318-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7318 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7318 BEM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7318 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7318 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7318 BEGAPH (PEEK cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7318 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 318 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 318 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7319 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 6050,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 168,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "For a 95 mm shaft carrying combined load, SKF lists 7319 under catalogue execution 7319 BEP: one open single-row angular-contact ball bearing, 40° contact angle, in the medium (7300) series of the 7xxx family.Digit by digit, 7319 reads as bearing type 7 (single-row angular contact), medium section diameter series 3, and bore reference 19 resolving to 95 mm; 200 mm OD and 45 width are the matching ISO 15 boundary values. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7319 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. Speed planning uses two different ceilings: 4,000 r/min reference (thermal, under representative load) and 3,800 r/min limiting (mechanical cage/ball limit). Note the minimum-axial-load requirement: at light radial load and high speed the balls of 7319 must still be held into the contact ellipse, which is another reason the catalogue recommends paired mounting with controlled preload on 95 mm shaft positions.",
    "applications": [
      "large process pumps and compressors",
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "At 95 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 73xx medium section at 95 mm bore (200×45 mm) is heavier-rated than the 7219 but runs hotter at the same speed; do not substitute a 7319 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "Do not mix execution classes inside one 7319 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7319 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "The 7319 shares its ISO 15 envelope with deep-groove 6319 but is not a drop-in replacement: it cannot run effectively under pure radial load without a minimum axial load, and a deep-groove bearing cannot replace its combined-load duty.",
      "The 168/150 kN ratings are SKF catalogue 17000 values for the 7319 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7319 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7319 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7319 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7319?",
        "a": "The SKF 7319 BEP is a single-row angular-contact ball bearing with 95 mm bore, 200 mm outer diameter and 45 mm width (3.74 × 7.874 × 1.772 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 168 kN, C0 150 kN, fatigue load limit Pu 5.2 kN, reference speed 4,000 r/min, limiting speed 3,800 r/min, mass about 6050 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 3,800 r/min value is the one to design against."
      },
      {
        "q": "How does the 7319 bore code work?",
        "a": "The last two digits of 7319 are bore code 19, so 19 × 5 = 95 mm bore. The 200 mm OD and 45 mm width come from the ISO 15 diameter-series plan, shared with the 6319 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7319 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7319 compare with a deep-groove 6319?",
        "a": "Both use the 95×200×45 mm ISO 15 envelope, but the angular-contact 7319 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 168 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6319",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6319-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6319-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7319 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7319 BEM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7319 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7319 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7319 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 319 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 319 N2PHAS shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7320 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 7500,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 203,
    "static_load_kN": 190,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "SKF 7320 (7320 BEP) is the medium (7300) series angular-contact choice for a 100 mm shaft — one row of balls on a steepened, asymmetric raceway giving a nominal 40° contact angle inside the 215×47 mm ISO 15 envelope.The code breaks down as type prefix 7 (angular contact), diameter series 3 (the medium section), and bore code 20 = 100 mm; dimensions 100×215×47 mm therefore match the 6320 deep-groove envelope even though the internal design is different. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7320 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 6.4 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.94 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Mounting practice for 7320: the rotating ring takes the interference fit (k5 on a 100 mm rotating shaft), the stationary ring slides for axial location, and reversing-thrust duty demands a paired DB/DF set rather than one bearing.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "heavy industrial gearboxes",
      "large process pumps and compressors"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "contact-angle shift and edge loading after a pair is tilted in by uneven locknut torque",
      "preload loss as a matched pair runs loose, letting the balls skid and smear the raceways",
      "cage pocket damage when the bearing is started cold with grease of too-high base-oil viscosity",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "At 100 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 73xx medium section at 100 mm bore (215×47 mm) is heavier-rated than the 7220 but runs hotter at the same speed; do not substitute a 7320 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "Do not mix execution classes inside one 7320 pair — universal-matchable (CB) bearings are ground for arbitrary pairing, but a CB unit paired with an unmatched basic BEP bearing will not share preload evenly.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7320 mounting error.",
      "The 7500 g mass and 47 mm width mean locknut and spacer faces must be square to the axis within the bearing's own P0 tolerance; a tilted spacer tilts the contact angle and concentrates load on one shoulder of 7320.",
      "The 203/190 kN ratings are SKF catalogue 17000 values for the 7320 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7320 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7320 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7320 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7320?",
        "a": "The SKF 7320 BEP is a single-row angular-contact ball bearing with 100 mm bore, 215 mm outer diameter and 47 mm width (3.937 × 8.465 × 1.85 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 203 kN, C0 190 kN, fatigue load limit Pu 6.4 kN, reference speed 3,800 r/min, limiting speed 3,600 r/min, mass about 7500 g. It is an open 40° contact-angle bearing with a PA66 cage. Preload and lubricant film move the real thermal limit, so treat 3,800 r/min as catalogue conditions, not a guarantee in the housing."
      },
      {
        "q": "How does the 7320 bore code work?",
        "a": "The last two digits of 7320 are bore code 20, so 20 × 5 = 100 mm bore. The 215 mm OD and 47 mm width come from the ISO 15 diameter-series plan, shared with the 6320 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7320 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Preload light/medium choice changes stiffness and heat, so calculate it from the load diagram rather than torquing until the pair feels tight."
      },
      {
        "q": "How does 7320 compare with a deep-groove 6320?",
        "a": "Both use the 100×215×47 mm ISO 15 envelope, but the angular-contact 7320 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. Envelope interchange is therefore dimensional only; the application must actually present axial load for the 7320 design to perform."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6320-2RS",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6320-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7320 BEM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7320 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7320 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7320 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7320 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-320-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 320 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7321",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7321 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 8550,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 203,
    "static_load_kN": 193,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "Ordering number 7321 BEP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 105 mm shaft, medium (7300) series, with an open PA66-caged execution and one-direction axial capacity.Reading the designation: the leading 7 marks a single-row angular-contact ball bearing, the 3 is ISO diameter series 3 (medium section), and the last two digits encode the 105 mm bore; the 225 mm OD and 49 mm width follow the ISO 15 general plan. In SKF suffix language B sets the steep 40° angle for high axial capacity, E is the optimised internal design, and P is the polymer cage; variants with seals (BE-2RZP), 25° angles (A/ACC) or brass cages (BECBM) are separate order numbers. Selection arithmetic: the C0/C ratio is about 0.95 (static 193 kN against dynamic 203 kN), typical of a 40° angle sized for axial capacity, and the 6.4 kN fatigue load limit Pu is the equivalent-load floor used in the SKF life calculation. Fit selection follows the rotating ring — interference on a rotating inner ring — and two 7321 units are required to take reversing thrust; keep the induced axial load (0.5·Fr/Y for the 40° angle) inside the rated capacity when calculating the pair.",
    "applications": [
      "heavy industrial gearboxes",
      "large process pumps and compressors",
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "fretting at the ground set faces of a pair whose clamp torque relaxes in service",
      "thermal preload runaway in a back-to-back pair when inner-ring heat has nowhere to expand",
      "PA66 cage embrittlement after sustained running above its 120 °C continuous-temperature ceiling",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At 105 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 73xx medium section at 105 mm bore (225×49 mm) is heavier-rated than the 7221 but runs hotter at the same speed; do not substitute a 7321 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "DB (back-to-back) pairs are stiffer against moments, DF (face-to-face) pairs tolerate misalignment and thermal growth better; choosing the arrangement from the 2D drawing rather than the actual shaft thermal expansion is a common 7321 mounting error.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7321 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "Open 7321 units need application-supplied sealing and a defined lubricant supply; in oil lubrication keep the oil level below the lowest rolling element or churning raises temperature well beyond the catalogue speed figures.",
      "The 203/193 kN ratings are SKF catalogue 17000 values for the 7321 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7321 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7321 BEP designation when purchasing and match the execution to the mounting arrangement.",
      "A plain 7321 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7321?",
        "a": "The SKF 7321 BEP is a single-row angular-contact ball bearing with 105 mm bore, 225 mm outer diameter and 49 mm width (4.134 × 8.858 × 1.929 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 203 kN, C0 193 kN, fatigue load limit Pu 6.4 kN, reference speed 3,600 r/min, limiting speed 3,400 r/min, mass about 8550 g. It is an open 40° contact-angle bearing with a PA66 cage. The two speed figures are independent limits and the operating point must clear both."
      },
      {
        "q": "How does the 7321 bore code work?",
        "a": "The last two digits of 7321 are bore code 21, so 21 × 5 = 105 mm bore. The 225 mm OD and 49 mm width come from the ISO 15 diameter-series plan, shared with the 6321 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BEP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. The plain BEP is the basic open single bearing; BECBP is the universally matchable version. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7321 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. Universally matchable CB executions can be assembled into pairs directly; define the preload class against the load and speed of the position."
      },
      {
        "q": "How does 7321 compare with a deep-groove 6321?",
        "a": "Both use the 105×225×49 mm ISO 15 envelope, but the angular-contact 7321 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. A 6321 cannot be dropped into a combined-load 7321 position and vice versa — verify load direction, Fa/Fr ratio and speed before substituting."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7321-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6321",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "6321-ZZ",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7321-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7321 BEP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7321-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7321 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7321-DECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7321 DECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7321 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322",
    "brand": "SKF",
    "manufacturer_designation": "SKF 7322 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "material": "GCr15",
    "weight_g": 10000,
    "weight_estimated": false,
    "standard": "ISO 15",
    "dynamic_load_kN": 240,
    "static_load_kN": 245,
    "fatigue_load_limit_kN": 7.8,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "naming_rule_text": "7322 is SKF's single-row angular-contact ball bearing in the medium (7300) series of the 7xxx range: an asymmetric-raceway open bearing with a nominal 40° contact angle, listed as 7322 BECBP in the SKF Rolling Bearings catalogue.Digit by digit, 7322 reads as bearing type 7 (single-row angular contact), medium section diameter series 3, and bore reference 22 resolving to 110 mm; 240 mm OD and 50 width are the matching ISO 15 boundary values. The suffix decodes as B for the 40° contact-angle execution, E for SKF's enhanced internal design with larger/fewer balls, and P for the glass-fibre reinforced PA66 ball-centred cage (continuous temperature ceiling 120 °C). CB means the side faces are ground for universal matching with Normal internal axial clearance, which is the starting point for field-set preload rather than a factory-matched fixed-preload set. The 65.0 mm radial section height ((240−110)/2) and 10000 g catalogue mass frame a 110 mm bore bearing rated at 240 kN C — roughly 2.18 kN of dynamic capacity per millimetre of bore before application factors. A single 7322 locates the shaft in one axial direction only; for bidirectional location order a matched pair — DB for moment stiffness, DF for tolerance of thermal expansion — and size the preload against the real load and speed of the position.",
    "applications": [
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives"
    ],
    "failure_modes": [
      "contamination wear through the open arrangement when no external seal is provided",
      "raceway smearing under marginal lubrication at start-up before oil reaches the contact ellipse",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "false brinelling on idle paired sets exposed to machine vibration",
      "cage wear from speed beyond the catalogue limiting value with thin or aged lubricant",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "At 110 mm bore the ring mass is high enough that cocking during mounting damages the cage and race lips; guide the ring square, confirm seat contact around the full circumference, and re-check preload after the first thermal cycle of the paired set.",
      "The 73xx medium section at 110 mm bore (240×50 mm) is heavier-rated than the 7222 but runs hotter at the same speed; do not substitute a 7322 into a 72-series spindle position without re-checking dn, lubricant film and preload.",
      "The 40° contact angle creates an induced axial load under pure radial force; include it in the 7322 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.",
      "Preload is a design value, not an assembly feel: excessive preload in the 7322 pair raises operating temperature and can trigger thermal runaway back-to-back, while too little lets the balls skid and smear the raceway under light load.",
      "Shaft and housing fillets must clear the bearing chamfer so the 50 mm-wide ring seats square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.",
      "The 240/245 kN ratings are SKF catalogue 17000 values for the 7322 BECBP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.",
      "SKF lists several executions of 7322 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7322 BECBP designation when purchasing and match the execution to the mounting arrangement.",
      "The CB execution (7322 BECBP) ships prepared for pair mounting but is not a matched set by itself: preload results from how the pair is clamped, so follow the SKF stand-off-ring and nut-torque procedure rather than assuming the bearings arrive preloaded."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of SKF 7322?",
        "a": "The SKF 7322 BECBP is a single-row angular-contact ball bearing with 110 mm bore, 240 mm outer diameter and 50 mm width (4.331 × 9.449 × 1.969 in) per ISO 15. From SKF catalogue 17000: basic dynamic load rating C 240 kN, C0 245 kN, fatigue load limit Pu 7.8 kN, reference speed 3,400 r/min, limiting speed 3,600 r/min, mass about 10000 g. It is an open 40° contact-angle bearing with a PA66 cage. Here the 3,400 r/min value is the one to design against."
      },
      {
        "q": "How does the 7322 bore code work?",
        "a": "The last two digits of 7322 are bore code 22, so 22 × 5 = 110 mm bore. The 240 mm OD and 50 mm width come from the ISO 15 diameter-series plan, shared with the 6322 deep-groove envelope."
      },
      {
        "q": "What do the 73xx and BECBP designations mean?",
        "a": "The leading 7 marks a single-row angular-contact bearing; the second digit 3 is the ISO diameter series (medium section). In the SKF suffix, B denotes the 40° contact angle, E the enhanced internal design, P the glass-fibre PA66 cage. CB adds Normal axial clearance with ground faces for universal DB/DF/DT pair mounting. A 25° variant (suffix A, e.g. ACC) runs faster but carries less thrust."
      },
      {
        "q": "Can a single 7322 take axial load in both directions?",
        "a": "No — one single-row angular-contact bearing reacts thrust in one direction only, and under radial load its 40° contact angle induces an axial force. Use two bearings as a matched pair: DB (back-to-back) for a rigid, moment-resisting arrangement, DF (face-to-face) where thermal expansion must be tolerated, or DT (tandem) where one-direction thrust is shared. A CB (universal) execution arrives with ground side faces for set mounting; basic BEP bearings are single units and are not ground for arbitrary pairing."
      },
      {
        "q": "How does 7322 compare with a deep-groove 6322?",
        "a": "Both use the 110×240×50 mm ISO 15 envelope, but the angular-contact 7322 has an asymmetric raceway at a nominal 40° angle: higher combined axial-plus-radial capacity and controlled preload, at the cost of speed, one-direction thrust, mandatory pairing for reversing loads and a minimum axial load requirement. The shared outline is why the two types cross-reference each other in catalogues, but ratings at 240 kN C apply only to the angular-contact design shown here."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "6322",
        "equiv_brand": "SKF",
        "level": "verify",
        "note": "Identical envelope but a different bearing type — confirm load and speed suitability before substitution."
      },
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7322 BEY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7322 BEM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7322 BECBP (glass-fibre PA66 cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7322 BECBY (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF 7322 BECBM (brass cage, open arrangement) is the same-envelope execution with ratings within 10 % — boundary dimensions interchangeable."
      },
      {
        "equiv_sku": "QJ-322-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF QJ 322 N2MA shares the envelope but catalogue C/C0 differ — envelope match only after a load check."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB",
    "extracted_at": "2026-09-26",
    "last_verified": "2026-09-26",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7200-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7200 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.02,
    "static_load_kN": 3.35,
    "fatigue_load_limit_kN": 0.14,
    "reference_speed_rpm": 30000,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "weight_g": 30,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7200 BECBP is SKF's 10 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 10×30×9 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 10×30×9 mm (0.394×1.181×0.354 in), 10.0 mm radial section height, C 7.02 kN, C0 3.35 kN, Pu 0.14 kN.reference speed 30,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical), which coincide for this size, catalogue mass 30 g. Load balance: C0 3.35 kN against C 7.02 kN gives a 0.48 ratio, typical of a steep-angle axial-oriented design; Pu 0.14 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 10 mm bore: 7.02 kN C divided by the 10.0 mm radial section height gives 0.7 kN per section millimetre; the 30 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 30 over bore 10 is a 3.00× step for this size, and the 9 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 10 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles",
      "small machine-tool spindles and high-speed heads"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "Assign interference to the rotating ring — roughly j5 on a 10 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring — roughly j5 on a 10 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7200-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7200-BECBP?",
        "a": "7200 BECBP measures 10 mm bore × 30 mm OD × 9 mm width (0.394 × 1.181 × 0.354 in), mass about 30 g. SKF 17000 ratings: C 7.02 kN, C0 3.35 kN, Pu 0.14 kN, reference speed 30,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7200-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 30,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7200-BECBP?",
        "a": "The 30,000 r/min reference (thermal) and 30,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7200-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 10×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7200-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×9 mm envelope with catalogue ratings within 10 %; 7200 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7200",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7200 BEP is the basic 10×30×9 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7200-BECBP",
      "7200 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7200-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7200 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.02,
    "static_load_kN": 3.35,
    "fatigue_load_limit_kN": 0.14,
    "reference_speed_rpm": 30000,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "weight_g": 30,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7200 BEP is SKF's 10 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 10×30×9 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 10×30×9 mm (0.394×1.181×0.354 in), 10.0 mm radial section height, C 7.02 kN, C0 3.35 kN, Pu 0.14 kN.reference speed 30,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical), which coincide for this size, catalogue mass 30 g. Sizing arithmetic on the 10 mm bore: 7.02 kN C divided by the 10.0 mm radial section height gives 0.7 kN per section millimetre; the 30 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. The 0.14 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 7.02/3.35 kN ratings and 30 g mass this execution carries about 0.70 kN of C per millimetre of bore. Bore-to-OD planning: OD 30 over bore 10 is a 3.00× step for this size, and the 9 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 10 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly j5 on a 10 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7200-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7200 BEP as the single basic pa66 execution; the other order numbers of the 7200 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7200-BEP?",
        "a": "7200 BEP measures 10 mm bore × 30 mm OD × 9 mm width (0.394 × 1.181 × 0.354 in), mass about 30 g. SKF 17000 ratings: C 7.02 kN, C0 3.35 kN, Pu 0.14 kN, reference speed 30,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7200-BEP?",
        "a": "With a rotating inner ring use roughly j5 on the 10 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7200-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 10×30×9 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7200-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×9 mm envelope with catalogue ratings within 10 %; 7200 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7200",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7200 BEP is the basic 10×30×9 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7200-BEP",
      "7200 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7201-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7201 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.61,
    "static_load_kN": 3.8,
    "fatigue_load_limit_kN": 0.16,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "weight_g": 36,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7201 BECBP is SKF's 12 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 12×32×10 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 12×32×10 mm (0.472×1.26×0.394 in), 10.0 mm radial section height, C 7.61 kN, C0 3.8 kN, Pu 0.16 kN.reference speed 28,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical), catalogue mass 36 g. At the printed limiting speed of 26,000 r/min the mean pitch diameter dm ≈ 22.0 mm implies a dn value around 572k mm·r/min; the 28,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 10 mm width over a 10.0 mm section yields 1.00 mm of ring width per section millimetre, and the bearing weighs 36 g for 7.61 kN of dynamic capacity — about 5 g per rated kN. Bore-to-OD planning: OD 32 over bore 12 is a 2.67× step for this size, and the 10 mm width gives a bore/width ratio of 1.20; use these ratios when housing space around the 12 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "high-speed engraving and routing spindles",
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 10 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 10 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7201-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7201-BECBP?",
        "a": "7201 BECBP measures 12 mm bore × 32 mm OD × 10 mm width (0.472 × 1.26 × 0.394 in), mass about 36 g. SKF 17000 ratings: C 7.61 kN, C0 3.8 kN, Pu 0.16 kN, reference speed 28,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7201-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7201-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7201-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×10 mm envelope with catalogue ratings within 10 %; 7201 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7201",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7201 BEP is the basic 12×32×10 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7201-BECBP",
      "7201 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7201-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7201 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 10,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.61,
    "static_load_kN": 3.8,
    "fatigue_load_limit_kN": 0.16,
    "reference_speed_rpm": 28000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "weight_g": 36,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7201 BEP is SKF's 12 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 12×32×10 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 12×32×10 mm (0.472×1.26×0.394 in), 10.0 mm radial section height, C 7.61 kN, C0 3.8 kN, Pu 0.16 kN.reference speed 28,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical), catalogue mass 36 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 26,000 r/min while thermal balance under catalogue load sets the 28,000 r/min reference; at dm ≈ 22.0 mm the corresponding dn is approximately 572k mm·r/min. Sizing arithmetic on the 12 mm bore: 7.61 kN C divided by the 10.0 mm radial section height gives 0.8 kN per section millimetre; the 36 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 32 over bore 12 is a 2.67× step for this size, and the 10 mm width gives a bore/width ratio of 1.20; use these ratios when housing space around the 12 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 10 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7201-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7201 BEP as the single basic pa66 execution; the other order numbers of the 7201 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7201-BEP?",
        "a": "7201 BEP measures 12 mm bore × 32 mm OD × 10 mm width (0.472 × 1.26 × 0.394 in), mass about 36 g. SKF 17000 ratings: C 7.61 kN, C0 3.8 kN, Pu 0.16 kN, reference speed 28,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7201-BEP?",
        "a": "The 28,000 r/min reference (thermal) and 26,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7201-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7201-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7201-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×10 mm envelope with catalogue ratings within 10 %; 7201 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7201",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7201 BEP is the basic 12×32×10 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7201-BEP",
      "7201 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7301-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7301 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.6,
    "static_load_kN": 5,
    "fatigue_load_limit_kN": 0.208,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7301 BE-2RZP is SKF's 12 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 12×37×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 12×37×12 mm (0.472×1.457×0.472 in), 12.5 mm radial section height, C 10.6 kN, C0 5 kN, Pu 0.208 kN.reference speed 26,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 60 g. Sizing arithmetic on the 12 mm bore: 10.6 kN C divided by the 12.5 mm radial section height gives 0.8 kN per section millimetre; the 60 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. The 0.208 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 10.6/5 kN ratings and 60 g mass this execution carries about 0.88 kN of C per millimetre of bore. Bore-to-OD planning: OD 37 over bore 12 is a 3.08× step for this size, and the 12 mm width gives a bore/width ratio of 1.00; use these ratios when housing space around the 12 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7301-BE-2RZP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7301-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7301-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7301-BE-2RZP?",
        "a": "7301 BE-2RZP measures 12 mm bore × 37 mm OD × 12 mm width (0.472 × 1.457 × 0.472 in), mass about 60 g. SKF 17000 ratings: C 10.6 kN, C0 5 kN, Pu 0.208 kN, reference speed 26,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Can one 7301-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7301-BE-2RZP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7301-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 12×37×12 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7301-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×37×12 mm envelope with catalogue ratings within 10 %; 7301 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7301",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7301 BEP is the basic 12×37×12 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7301-BE-2RZP",
      "7301 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7301-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7301 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 37,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.6,
    "static_load_kN": 5,
    "fatigue_load_limit_kN": 0.208,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 60,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7301 BEP is SKF's 12 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 12×37×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 12×37×12 mm (0.472×1.457×0.472 in), 12.5 mm radial section height, C 10.6 kN, C0 5 kN, Pu 0.208 kN.reference speed 26,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical), catalogue mass 60 g. Sizing arithmetic on the 12 mm bore: 10.6 kN C divided by the 12.5 mm radial section height gives 0.8 kN per section millimetre; the 60 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. The 0.208 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 10.6/5 kN ratings and 60 g mass this execution carries about 0.88 kN of C per millimetre of bore. Bore-to-OD planning: OD 37 over bore 12 is a 3.08× step for this size, and the 12 mm width gives a bore/width ratio of 1.00; use these ratios when housing space around the 12 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly j5 on a 12 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7301-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7301 BEP as the single basic pa66 execution; the other order numbers of the 7301 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7301-BEP?",
        "a": "7301 BEP measures 12 mm bore × 37 mm OD × 12 mm width (0.472 × 1.457 × 0.472 in), mass about 60 g. SKF 17000 ratings: C 10.6 kN, C0 5 kN, Pu 0.208 kN, reference speed 26,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7301-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 24,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7301-BEP?",
        "a": "The 26,000 r/min reference (thermal) and 24,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7301-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 12×37×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7301-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×37×12 mm envelope with catalogue ratings within 10 %; 7301 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7301",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7301 BEP is the basic 12×37×12 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7301-BEP",
      "7301 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7202 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.32,
    "static_load_kN": 4.4,
    "fatigue_load_limit_kN": 0.183,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 45,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7202 BE-2RZP is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 15×35×11 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 15×35×11 mm (0.591×1.378×0.433 in), 10.0 mm radial section height, C 8.32 kN, C0 4.4 kN, Pu 0.183 kN.reference speed 24,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 45 g. Mass and section check: 45 g inside the 15×35×11 mm outline leaves a 10.0 mm radial section, and the 4.4 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 4.4 kN against C 8.32 kN gives a 0.53 ratio, typical of a steep-angle axial-oriented design; Pu 0.183 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 24,000 r/min against a 20,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.20. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7202-BE-2RZP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BE-2RZP unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7202-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7202-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7202-BE-2RZP?",
        "a": "7202 BE-2RZP measures 15 mm bore × 35 mm OD × 11 mm width (0.591 × 1.378 × 0.433 in), mass about 45 g. SKF 17000 ratings: C 8.32 kN, C0 4.4 kN, Pu 0.183 kN, reference speed 24,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7202-BE-2RZP?",
        "a": "With a rotating inner ring use roughly j5 on the 15 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7202-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×11 mm envelope with catalogue ratings within 10 %; 7202 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7202-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×11 mm envelope with catalogue ratings within 10 %; 7202 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7202-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (8.32/4.4 kN vs 10.2/5.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-202-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (8.32/4.4 kN vs 12.7/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7202 BEP is the basic 15×35×11 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202-BE-2RZP",
      "7202 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7202 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.32,
    "static_load_kN": 4.4,
    "fatigue_load_limit_kN": 0.183,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 45,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7202 BEP is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 15×35×11 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 15×35×11 mm (0.591×1.378×0.433 in), 10.0 mm radial section height, C 8.32 kN, C0 4.4 kN, Pu 0.183 kN.reference speed 24,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical), which coincide for this size, catalogue mass 45 g. Mass and section check: 45 g inside the 15×35×11 mm outline leaves a 10.0 mm radial section, and the 4.4 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 4.4 kN against C 8.32 kN gives a 0.53 ratio, typical of a steep-angle axial-oriented design; Pu 0.183 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 24,000 r/min against a 24,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 15 mm bore the j5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7202-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7202 BEP as the single basic pa66 execution; the other order numbers of the 7202 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7202-BEP?",
        "a": "7202 BEP measures 15 mm bore × 35 mm OD × 11 mm width (0.591 × 1.378 × 0.433 in), mass about 45 g. SKF 17000 ratings: C 8.32 kN, C0 4.4 kN, Pu 0.183 kN, reference speed 24,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7202-BEP?",
        "a": "With a rotating inner ring use roughly j5 on the 15 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7202-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×11 mm envelope with catalogue ratings within 10 %; 7202 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7202-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×11 mm envelope with catalogue ratings within 10 %; 7202 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7202-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (8.32/4.4 kN vs 10.2/5.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-202-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (8.32/4.4 kN vs 12.7/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7202 BEP is the basic 15×35×11 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202-BEP",
      "7202 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7202 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 8.8,
    "static_load_kN": 4.65,
    "fatigue_load_limit_kN": 0.196,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "weight_g": 45,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7202 BECBP is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 15×35×11 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 15×35×11 mm (0.591×1.378×0.433 in), 10.0 mm radial section height, C 8.8 kN, C0 4.65 kN, Pu 0.196 kN.reference speed 24,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical), catalogue mass 45 g. Sizing arithmetic on the 15 mm bore: 8.8 kN C divided by the 10.0 mm radial section height gives 0.9 kN per section millimetre; the 45 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 45 g inside the 15×35×11 mm outline leaves a 10.0 mm radial section, and the 4.65 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 24,000 r/min against a 26,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 11 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "At 15 mm bore the j5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7202-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7202-BECBP?",
        "a": "7202 BECBP measures 15 mm bore × 35 mm OD × 11 mm width (0.591 × 1.378 × 0.433 in), mass about 45 g. SKF 17000 ratings: C 8.8 kN, C0 4.65 kN, Pu 0.196 kN, reference speed 24,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7202-BECBP?",
        "a": "With a rotating inner ring use roughly j5 on the 15 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7202-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×11 mm envelope with catalogue ratings within 10 %; 7202 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7202-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×11 mm envelope with catalogue ratings within 10 %; 7202 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7202-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (8.8/4.65 kN vs 10.2/5.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-202-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (8.8/4.65 kN vs 12.7/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7202 BEP is the basic 15×35×11 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202-BECBP",
      "7202 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7202-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7202 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 10.2,
    "static_load_kN": 5.2,
    "fatigue_load_limit_kN": 0.224,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 40000,
    "max_rpm": 40000,
    "weight_g": 45,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7202 ACCBM is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 15×35×11 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 15×35×11 mm (0.591×1.378×0.433 in), 10.0 mm radial section height, C 10.2 kN, C0 5.2 kN, Pu 0.224 kN.reference speed 26,000 r/min (thermal) and limiting speed 40,000 r/min (mechanical), catalogue mass 45 g. Envelope economics: the 11 mm width over a 10.0 mm section yields 1.10 mm of ring width per section millimetre, and the bearing weighs 45 g for 10.2 kN of dynamic capacity — about 4 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 40,000 r/min while thermal balance under catalogue load sets the 26,000 r/min reference; at dm ≈ 25.0 mm the corresponding dn is approximately 1,000k mm·r/min. Bore-to-OD planning: OD 35 over bore 15 is a 2.33× step for this size, and the 11 mm width gives a bore/width ratio of 1.36; use these ratios when housing space around the 15 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly j5 on a 15 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Assign interference to the rotating ring — roughly j5 on a 15 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The 25° AC angle of 7202-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7202-ACCBM?",
        "a": "7202 ACCBM measures 15 mm bore × 35 mm OD × 11 mm width (0.591 × 1.378 × 0.433 in), mass about 45 g. SKF 17000 ratings: C 10.2 kN, C0 5.2 kN, Pu 0.224 kN, reference speed 26,000 r/min (thermal) and limiting speed 40,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7202-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7202-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (10.2/5.2 kN vs 8.32/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (10.2/5.2 kN vs 8.32/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (10.2/5.2 kN vs 8.8/4.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-202-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (10.2/5.2 kN vs 12.7/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7202 BEP shares the 15×35×11 mm angular-contact envelope, but catalogue C/C0 differ (10.2/5.2 kN vs 8.32/4.4 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7202-ACCBM",
      "7202 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7302-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7302 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 13,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.28,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 82,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7302 BE-2RZP is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 15×42×13 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 15×42×13 mm (0.591×1.654×0.512 in), 13.5 mm radial section height, C 13 kN, C0 6.7 kN, Pu 0.28 kN.reference speed 22,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 82 g. Envelope economics: the 13 mm width over a 13.5 mm section yields 0.96 mm of ring width per section millimetre, and the bearing weighs 82 g for 13 kN of dynamic capacity — about 6 g per rated kN. Mass and section check: 82 g inside the 15×42×13 mm outline leaves a 13.5 mm radial section, and the 6.7 kN static rating is 0.52× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 17,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.29. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "small gear and metering pumps",
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 15 mm bore the j5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7302-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7302-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7302-BE-2RZP?",
        "a": "7302 BE-2RZP measures 15 mm bore × 42 mm OD × 13 mm width (0.591 × 1.654 × 0.512 in), mass about 82 g. SKF 17000 ratings: C 13 kN, C0 6.7 kN, Pu 0.28 kN, reference speed 22,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Which fits should I use for 7302-BE-2RZP?",
        "a": "With a rotating inner ring use roughly j5 on the 15 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7302-BE-2RZP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 17,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7302-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7302-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×13 mm envelope with catalogue ratings within 10 %; 7302 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7302-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×13 mm envelope with catalogue ratings within 10 %; 7302 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7302",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7302 BEP is the basic 15×42×13 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7302-BE-2RZP",
      "7302 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7302-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7302 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 13,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.28,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 80,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7302 BECBP is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 15×42×13 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 15×42×13 mm (0.591×1.654×0.512 in), 13.5 mm radial section height, C 13 kN, C0 6.7 kN, Pu 0.28 kN.reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 80 g. Selection figures for 7302 BECBP: the static-to-dynamic ratio C0/C is 0.52, Pu 0.28 kN is about 2 % of C, and catalogue mass works out to roughly 5 g per millimetre of bore. At the printed limiting speed of 20,000 r/min the mean pitch diameter dm ≈ 28.5 mm implies a dn value around 570k mm·r/min; the 22,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 20,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.10. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7302-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7302-BECBP?",
        "a": "7302 BECBP measures 15 mm bore × 42 mm OD × 13 mm width (0.591 × 1.654 × 0.512 in), mass about 80 g. SKF 17000 ratings: C 13 kN, C0 6.7 kN, Pu 0.28 kN, reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7302-BECBP?",
        "a": "With a rotating inner ring use roughly j5 on the 15 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7302-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 20,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7302-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7302-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×13 mm envelope with catalogue ratings within 10 %; 7302 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7302-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×13 mm envelope with catalogue ratings within 10 %; 7302 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7302",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7302 BEP is the basic 15×42×13 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7302-BECBP",
      "7302 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7302-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7302 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 13,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 13,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.28,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 80,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7302 BEP is SKF's 15 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 15×42×13 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 15×42×13 mm (0.591×1.654×0.512 in), 13.5 mm radial section height, C 13 kN, C0 6.7 kN, Pu 0.28 kN.reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 80 g. Envelope economics: the 13 mm width over a 13.5 mm section yields 0.96 mm of ring width per section millimetre, and the bearing weighs 80 g for 13 kN of dynamic capacity — about 6 g per rated kN. Mass and section check: 80 g inside the 15×42×13 mm outline leaves a 13.5 mm radial section, and the 6.7 kN static rating is 0.52× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 20,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.10. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "small gear and metering pumps",
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 13 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 13 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7302-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7302 BEP as the single basic pa66 execution; the other order numbers of the 7302 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7302-BEP?",
        "a": "7302 BEP measures 15 mm bore × 42 mm OD × 13 mm width (0.591 × 1.654 × 0.512 in), mass about 80 g. SKF 17000 ratings: C 13 kN, C0 6.7 kN, Pu 0.28 kN, reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which fits should I use for 7302-BEP?",
        "a": "With a rotating inner ring use roughly j5 on the 15 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7302-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 20,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7302-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 15×42×13 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7302-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×13 mm envelope with catalogue ratings within 10 %; 7302 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7302-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×13 mm envelope with catalogue ratings within 10 %; 7302 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7302",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7302 BEP is the basic 15×42×13 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7302-BEP",
      "7302 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7203 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.4,
    "static_load_kN": 5.5,
    "fatigue_load_limit_kN": 0.236,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 63,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203 BE-2RZP is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 17×40×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 10.4 kN, C0 5.5 kN, Pu 0.236 kN.reference speed 22,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 63 g. Envelope economics: the 12 mm width over a 11.5 mm section yields 1.04 mm of ring width per section millimetre, and the bearing weighs 63 g for 10.4 kN of dynamic capacity — about 6 g per rated kN. Mass and section check: 63 g inside the 17×40×12 mm outline leaves a 11.5 mm radial section, and the 5.5 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 17,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.29. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "small gear and metering pumps",
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "At 17 mm bore the j5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7203-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 12 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7203-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7203-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7203-BE-2RZP?",
        "a": "7203 BE-2RZP measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 63 g. SKF 17000 ratings: C 10.4 kN, C0 5.5 kN, Pu 0.236 kN, reference speed 22,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7203-BE-2RZP?",
        "a": "The 22,000 r/min reference (thermal) and 17,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7203-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (10.4/5.5 kN vs 11.1/6.1 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (10.4/5.5 kN vs 12.5/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (10.4/5.5 kN vs 17/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7203 BEP is the basic 17×40×12 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203-BE-2RZP",
      "7203 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7203 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.4,
    "static_load_kN": 5.5,
    "fatigue_load_limit_kN": 0.236,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 65,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203 BEP is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 17×40×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 10.4 kN, C0 5.5 kN, Pu 0.236 kN.reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 65 g. Envelope economics: the 12 mm width over a 11.5 mm section yields 1.04 mm of ring width per section millimetre, and the bearing weighs 65 g for 10.4 kN of dynamic capacity — about 6 g per rated kN. Mass and section check: 65 g inside the 17×40×12 mm outline leaves a 11.5 mm radial section, and the 5.5 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 20,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.10. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "small gear and metering pumps",
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7203-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7203-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7203 BEP as the single basic pa66 execution; the other order numbers of the 7203 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7203-BEP?",
        "a": "7203 BEP measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 65 g. SKF 17000 ratings: C 10.4 kN, C0 5.5 kN, Pu 0.236 kN, reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7203-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (10.4/5.5 kN vs 11.1/6.1 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (10.4/5.5 kN vs 12.5/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (10.4/5.5 kN vs 17/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7203 BEP is the basic 17×40×12 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203-BEP",
      "7203 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7203 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 11,
    "static_load_kN": 5.85,
    "fatigue_load_limit_kN": 0.25,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 65,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203 BECBP is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 17×40×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 11 kN, C0 5.85 kN, Pu 0.25 kN.reference speed 22,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical), which coincide for this size, catalogue mass 65 g. Selection figures for 7203 BECBP: the static-to-dynamic ratio C0/C is 0.53, Pu 0.25 kN is about 2 % of C, and catalogue mass works out to roughly 4 g per millimetre of bore. At the printed limiting speed of 22,000 r/min the mean pitch diameter dm ≈ 28.5 mm implies a dn value around 627k mm·r/min; the 22,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 22,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7203-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7203-BECBP?",
        "a": "7203 BECBP measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 65 g. SKF 17000 ratings: C 11 kN, C0 5.85 kN, Pu 0.25 kN, reference speed 22,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7203-BECBP?",
        "a": "The 22,000 r/min reference (thermal) and 22,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7203-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11/5.85 kN vs 12.5/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11/5.85 kN vs 17/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7203 BEP is the basic 17×40×12 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203-BECBP",
      "7203 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7203 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 11,
    "static_load_kN": 5.85,
    "fatigue_load_limit_kN": 0.25,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 28000,
    "max_rpm": 28000,
    "weight_g": 65,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203 BECBM is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 17×40×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 11 kN, C0 5.85 kN, Pu 0.25 kN.reference speed 22,000 r/min (thermal) and limiting speed 28,000 r/min (mechanical), catalogue mass 65 g. Sizing arithmetic on the 17 mm bore: 11 kN C divided by the 11.5 mm radial section height gives 1.0 kN per section millimetre; the 65 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 65 g inside the 17×40×12 mm outline leaves a 11.5 mm radial section, and the 5.85 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 28,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.79. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly j5 on a 17 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 17 mm bore the j5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7203-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7203-BECBM?",
        "a": "7203 BECBM measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 65 g. SKF 17000 ratings: C 11 kN, C0 5.85 kN, Pu 0.25 kN, reference speed 22,000 r/min (thermal) and limiting speed 28,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7203-BECBM?",
        "a": "With a rotating inner ring use roughly j5 on the 17 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11/5.85 kN vs 12.5/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11/5.85 kN vs 17/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7203 BEP is the basic 17×40×12 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203-BECBM",
      "7203 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-BEY",
    "brand": "SKF",
    "manufacturer_designation": "7203 BEY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 11.1,
    "static_load_kN": 6.1,
    "fatigue_load_limit_kN": 0.26,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 65,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203 BEY is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 17×40×12 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 11.1 kN, C0 6.1 kN, Pu 0.26 kN.reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 65 g. At the printed limiting speed of 20,000 r/min the mean pitch diameter dm ≈ 28.5 mm implies a dn value around 570k mm·r/min; the 22,000 r/min reference speed is the thermal-planning figure under catalogue load. Selection figures for 7203 BEY: the static-to-dynamic ratio C0/C is 0.55, Pu 0.26 kN is about 2 % of C, and catalogue mass works out to roughly 4 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 20,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.10. Ordering note: BEY is the basic single bearing with the stamped brass strip cage (Y) — light and oil-additive tolerant, but not ground on the side faces for set mounting; order BECBY for a universally matchable stamped-brass unit.",
    "applications": [
      "high-speed engraving and routing spindles",
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7203-BEY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7203 BEY as the single basic stamped brass execution; the other order numbers of the 7203 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7203-BEY?",
        "a": "7203 BEY measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 65 g. SKF 17000 ratings: C 11.1 kN, C0 6.1 kN, Pu 0.26 kN, reference speed 22,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.."
      },
      {
        "q": "Which fits should I use for 7203-BEY?",
        "a": "With a rotating inner ring use roughly j5 on the 17 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7203-BEY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 20,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11.1/6.1 kN vs 10.4/5.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11.1/6.1 kN vs 10.4/5.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×12 mm envelope with catalogue ratings within 10 %; 7203 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11.1/6.1 kN vs 12.5/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (11.1/6.1 kN vs 17/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7203 BEP shares the 17×40×12 mm angular-contact envelope, but catalogue C/C0 differ (11.1/6.1 kN vs 10.4/5.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203-BEY",
      "7203 BEY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7203-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7203 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 12.5,
    "static_load_kN": 6.7,
    "fatigue_load_limit_kN": 0.285,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 34000,
    "max_rpm": 34000,
    "weight_g": 65,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7203 ACCBM is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 17×40×12 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 12.5 kN, C0 6.7 kN, Pu 0.285 kN.reference speed 24,000 r/min (thermal) and limiting speed 34,000 r/min (mechanical), catalogue mass 65 g. Sizing arithmetic on the 17 mm bore: 12.5 kN C divided by the 11.5 mm radial section height gives 1.1 kN per section millimetre; the 65 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 65 g inside the 17×40×12 mm outline leaves a 11.5 mm radial section, and the 6.7 kN static rating is 0.54× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 40 over bore 17 is a 2.35× step for this size, and the 12 mm width gives a bore/width ratio of 1.42; use these ratios when housing space around the 17 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly j5 on a 17 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring — roughly j5 on a 17 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The 25° AC angle of 7203-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7203-ACCBM?",
        "a": "7203 ACCBM measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 65 g. SKF 17000 ratings: C 12.5 kN, C0 6.7 kN, Pu 0.285 kN, reference speed 24,000 r/min (thermal) and limiting speed 34,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7203-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7203-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (12.5/6.7 kN vs 10.4/5.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (12.5/6.7 kN vs 10.4/5.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (12.5/6.7 kN vs 11/5.85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (12.5/6.7 kN vs 11/5.85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (12.5/6.7 kN vs 11.1/6.1 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-203-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (12.5/6.7 kN vs 17/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7203 BEP shares the 17×40×12 mm angular-contact envelope, but catalogue C/C0 differ (12.5/6.7 kN vs 10.4/5.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7203-ACCBM",
      "7203 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7303-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7303 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 8.3,
    "fatigue_load_limit_kN": 0.355,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7303 BE-2RZP is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 17×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 17×47×14 mm (0.669×1.85×0.551 in), 15.0 mm radial section height, C 15.9 kN, C0 8.3 kN, Pu 0.355 kN.reference speed 20,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 110 g. Mass and section check: 110 g inside the 17×47×14 mm outline leaves a 15.0 mm radial section, and the 8.3 kN static rating is 0.52× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 8.3 kN against C 15.9 kN gives a 0.52 ratio, typical of a steep-angle axial-oriented design; Pu 0.355 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 20,000 r/min against a 15,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.33. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7303-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable BE-2RZP unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7303-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7303-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7303-BE-2RZP?",
        "a": "7303 BE-2RZP measures 17 mm bore × 47 mm OD × 14 mm width (0.669 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 15.9 kN, C0 8.3 kN, Pu 0.355 kN, reference speed 20,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Which grease and fill for 7303-BE-2RZP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 15,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7303-BE-2RZP?",
        "a": "The 20,000 r/min reference (thermal) and 15,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7303-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×14 mm envelope with catalogue ratings within 10 %; 7303 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7303-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×14 mm envelope with catalogue ratings within 10 %; 7303 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-303-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope, but catalogue C/C0 differ between executions (15.9/8.3 kN vs 23.4/15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7303",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7303 BEP is the basic 17×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7303-BE-2RZP",
      "7303 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7303-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7303 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 8.3,
    "fatigue_load_limit_kN": 0.355,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7303 BECBP is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 17×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 17×47×14 mm (0.669×1.85×0.551 in), 15.0 mm radial section height, C 15.9 kN, C0 8.3 kN, Pu 0.355 kN.reference speed 20,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), catalogue mass 110 g. Sizing arithmetic on the 17 mm bore: 15.9 kN C divided by the 15.0 mm radial section height gives 1.1 kN per section millimetre; the 110 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 110 g inside the 17×47×14 mm outline leaves a 15.0 mm radial section, and the 8.3 kN static rating is 0.52× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 20,000 r/min against a 19,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.05. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly j5 on a 17 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7303-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7303-BECBP?",
        "a": "7303 BECBP measures 17 mm bore × 47 mm OD × 14 mm width (0.669 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 15.9 kN, C0 8.3 kN, Pu 0.355 kN, reference speed 20,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7303-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7303-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7303-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×14 mm envelope with catalogue ratings within 10 %; 7303 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7303-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×14 mm envelope with catalogue ratings within 10 %; 7303 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-303-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope, but catalogue C/C0 differ between executions (15.9/8.3 kN vs 23.4/15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7303",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7303 BEP is the basic 17×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7303-BECBP",
      "7303 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7303-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7303 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.9,
    "static_load_kN": 8.3,
    "fatigue_load_limit_kN": 0.355,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7303 BEP is SKF's 17 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 17×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 17×47×14 mm (0.669×1.85×0.551 in), 15.0 mm radial section height, C 15.9 kN, C0 8.3 kN, Pu 0.355 kN.reference speed 20,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), catalogue mass 110 g. Mass and section check: 110 g inside the 17×47×14 mm outline leaves a 15.0 mm radial section, and the 8.3 kN static rating is 0.52× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 8.3 kN against C 15.9 kN gives a 0.52 ratio, typical of a steep-angle axial-oriented design; Pu 0.355 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 20,000 r/min against a 19,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.05. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts",
      "textile and wire-guide spindles"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7303-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7303 BEP as the single basic pa66 execution; the other order numbers of the 7303 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7303-BEP?",
        "a": "7303 BEP measures 17 mm bore × 47 mm OD × 14 mm width (0.669 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 15.9 kN, C0 8.3 kN, Pu 0.355 kN, reference speed 20,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Can one 7303-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7303-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7303-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×14 mm envelope with catalogue ratings within 10 %; 7303 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7303-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×14 mm envelope with catalogue ratings within 10 %; 7303 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-303-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope, but catalogue C/C0 differ between executions (15.9/8.3 kN vs 23.4/15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7303",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7303 BEP is the basic 17×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7303-BEP",
      "7303 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7204 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 13.3,
    "static_load_kN": 7.65,
    "fatigue_load_limit_kN": 0.325,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 BE-2RZP is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 20×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 13.3 kN, C0 7.65 kN, Pu 0.325 kN.reference speed 19,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 150 g. The 0.325 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 13.3/7.65 kN ratings and 150 g mass this execution carries about 0.67 kN of C per millimetre of bore. Sizing arithmetic on the 20 mm bore: 13.3 kN C divided by the 13.5 mm radial section height gives 1.0 kN per section millimetre; the 150 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 14 mm width gives a bore/width ratio of 1.43; use these ratios when housing space around the 20 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles",
      "small machine-tool spindles and high-speed heads"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BE-2RZP unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 20 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7204-BE-2RZP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7204-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7204-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-BE-2RZP?",
        "a": "7204 BE-2RZP measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 150 g. SKF 17000 ratings: C 13.3 kN, C0 7.65 kN, Pu 0.325 kN, reference speed 19,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Can one 7204-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7204-BE-2RZP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (13.3/7.65 kN vs 16/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7204 BEP is the basic 20×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-BE-2RZP",
      "7204 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7204 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 13.3,
    "static_load_kN": 7.65,
    "fatigue_load_limit_kN": 0.325,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 BEP is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 20×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 13.3 kN, C0 7.65 kN, Pu 0.325 kN.reference speed 19,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 110 g. The 0.325 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 13.3/7.65 kN ratings and 110 g mass this execution carries about 0.67 kN of C per millimetre of bore. Sizing arithmetic on the 20 mm bore: 13.3 kN C divided by the 13.5 mm radial section height gives 1.0 kN per section millimetre; the 110 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 14 mm width gives a bore/width ratio of 1.43; use these ratios when housing space around the 20 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles",
      "small machine-tool spindles and high-speed heads"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "One 7204-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7204-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7204-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7204-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7204 BEP as the single basic pa66 execution; the other order numbers of the 7204 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-BEP?",
        "a": "7204 BEP measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 13.3 kN, C0 7.65 kN, Pu 0.325 kN, reference speed 19,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7204-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 18,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7204-BEP?",
        "a": "The 19,000 r/min reference (thermal) and 18,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (13.3/7.65 kN vs 16/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7204 BEP is the basic 20×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-BEP",
      "7204 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7204 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.345,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 BECBP is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 20×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 14.3 kN, C0 8.15 kN, Pu 0.345 kN.reference speed 19,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), which coincide for this size, catalogue mass 110 g. Mass and section check: 110 g inside the 20×47×14 mm outline leaves a 13.5 mm radial section, and the 8.15 kN static rating is 0.57× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 0.345 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 14.3/8.15 kN ratings and 110 g mass this execution carries about 0.72 kN of C per millimetre of bore. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 14 mm width gives a bore/width ratio of 1.43; use these ratios when housing space around the 20 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 20 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "At 20 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7204-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-BECBP?",
        "a": "7204 BECBP measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 14.3 kN, C0 8.15 kN, Pu 0.345 kN, reference speed 19,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7204-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 19,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7204-BECBP?",
        "a": "The 19,000 r/min reference (thermal) and 19,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (14.3/8.15 kN vs 16/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7204 BEP is the basic 20×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-BECBP",
      "7204 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7204 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.345,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 BECBPH is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 20×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 14.3 kN, C0 8.15 kN, Pu 0.345 kN.reference speed 19,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), which coincide for this size, catalogue mass 110 g. The 0.345 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 14.3/8.15 kN ratings and 110 g mass this execution carries about 0.72 kN of C per millimetre of bore. Selection figures for 7204 BECBPH: the static-to-dynamic ratio C0/C is 0.57, Pu 0.345 kN is about 2 % of C, and catalogue mass works out to roughly 6 g per millimetre of bore. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 14 mm width gives a bore/width ratio of 1.43; use these ratios when housing space around the 20 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 20 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Fillet radii must clear the chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7204-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-BECBPH?",
        "a": "7204 BECBPH measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 14.3 kN, C0 8.15 kN, Pu 0.345 kN, reference speed 19,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Can one 7204-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7204-BECBPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (14.3/8.15 kN vs 16/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7204 BEP is the basic 20×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-BECBPH",
      "7204 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7204 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.345,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 BECBY is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 20×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 14.3 kN, C0 8.15 kN, Pu 0.345 kN.reference speed 19,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), which coincide for this size, catalogue mass 110 g. Sizing arithmetic on the 20 mm bore: 14.3 kN C divided by the 13.5 mm radial section height gives 1.1 kN per section millimetre; the 110 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. The 0.345 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 14.3/8.15 kN ratings and 110 g mass this execution carries about 0.72 kN of C per millimetre of bore. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 14 mm width gives a bore/width ratio of 1.43; use these ratios when housing space around the 20 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 14 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7204-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-BECBY?",
        "a": "7204 BECBY measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 14.3 kN, C0 8.15 kN, Pu 0.345 kN, reference speed 19,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7204-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 19,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7204-BECBY?",
        "a": "The 19,000 r/min reference (thermal) and 19,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (14.3/8.15 kN vs 16/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7204 BEP is the basic 20×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-BECBY",
      "7204 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7204 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.15,
    "fatigue_load_limit_kN": 0.345,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 BECBM is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 20×47×14 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 14.3 kN, C0 8.15 kN, Pu 0.345 kN.reference speed 19,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical), catalogue mass 110 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 24,000 r/min while thermal balance under catalogue load sets the 19,000 r/min reference; at dm ≈ 33.5 mm the corresponding dn is approximately 804k mm·r/min. Selection figures for 7204 BECBM: the static-to-dynamic ratio C0/C is 0.57, Pu 0.345 kN is about 2 % of C, and catalogue mass works out to roughly 6 g per millimetre of bore. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 14 mm width gives a bore/width ratio of 1.43; use these ratios when housing space around the 20 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "small gear and metering pumps",
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "One 7204-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7204-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-BECBM?",
        "a": "7204 BECBM measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 14.3 kN, C0 8.15 kN, Pu 0.345 kN, reference speed 19,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7204-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 20 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7204-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 24,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×14 mm envelope with catalogue ratings within 10 %; 7204 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7204-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (14.3/8.15 kN vs 16/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7204 BEP is the basic 20×47×14 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-BECBM",
      "7204 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7204-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7204 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 16,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.39,
    "reference_speed_rpm": 20000,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "weight_g": 110,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7204 ACCBM is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 20×47×14 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 20×47×14 mm (0.787×1.85×0.551 in), 13.5 mm radial section height, C 16 kN, C0 9.3 kN, Pu 0.39 kN.reference speed 20,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical), catalogue mass 110 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 30,000 r/min while thermal balance under catalogue load sets the 20,000 r/min reference; at dm ≈ 33.5 mm the corresponding dn is approximately 1,005k mm·r/min. Selection figures for 7204 ACCBM: the static-to-dynamic ratio C0/C is 0.58, Pu 0.39 kN is about 2 % of C, and catalogue mass works out to roughly 6 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 20,000 r/min against a 30,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.67. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "high-speed engraving and routing spindles",
      "small machine-tool spindles and high-speed heads",
      "servo and stepper motor shafts"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "At 20 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The 25° AC angle of 7204-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7204-ACCBM?",
        "a": "7204 ACCBM measures 20 mm bore × 47 mm OD × 14 mm width (0.787 × 1.85 × 0.551 in), mass about 110 g. SKF 17000 ratings: C 16 kN, C0 9.3 kN, Pu 0.39 kN, reference speed 20,000 r/min (thermal) and limiting speed 30,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7204-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7204-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7204-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (16/9.3 kN vs 13.3/7.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (16/9.3 kN vs 13.3/7.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (16/9.3 kN vs 14.3/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (16/9.3 kN vs 14.3/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (16/9.3 kN vs 14.3/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×47×14 mm envelope, but catalogue C/C0 differ between executions (16/9.3 kN vs 14.3/8.15 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7204",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7204 BEP shares the 20×47×14 mm angular-contact envelope, but catalogue C/C0 differ (16/9.3 kN vs 13.3/7.65 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7204-ACCBM",
      "7204 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7304 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 17.4,
    "static_load_kN": 9.5,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 BE-2RZP is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 20×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 17.4 kN, C0 9.5 kN, Pu 0.4 kN.reference speed 17,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 140 g. At the printed limiting speed of 13,000 r/min the mean pitch diameter dm ≈ 36.0 mm implies a dn value around 468k mm·r/min; the 17,000 r/min reference speed is the thermal-planning figure under catalogue load. The 0.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 17.4/9.5 kN ratings and 140 g mass this execution carries about 0.87 kN of C per millimetre of bore. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "servo and stepper motor shafts",
      "textile and wire-guide spindles",
      "small gear and metering pumps"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7304-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7304-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-BE-2RZP?",
        "a": "7304 BE-2RZP measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 17.4 kN, C0 9.5 kN, Pu 0.4 kN, reference speed 17,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7304-BE-2RZP?",
        "a": "The 17,000 r/min reference (thermal) and 13,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7304-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7304 BEP is the basic 20×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-BE-2RZP",
      "7304 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7304 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 17.4,
    "static_load_kN": 9.5,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 BEP is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 20×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 17.4 kN, C0 9.5 kN, Pu 0.4 kN.reference speed 17,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical), catalogue mass 140 g. At the printed limiting speed of 16,000 r/min the mean pitch diameter dm ≈ 36.0 mm implies a dn value around 576k mm·r/min; the 17,000 r/min reference speed is the thermal-planning figure under catalogue load. The 0.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 17.4/9.5 kN ratings and 140 g mass this execution carries about 0.87 kN of C per millimetre of bore. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "servo and stepper motor shafts",
      "textile and wire-guide spindles",
      "small gear and metering pumps"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7304-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7304-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7304 BEP as the single basic pa66 execution; the other order numbers of the 7304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-BEP?",
        "a": "7304 BEP measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 17.4 kN, C0 9.5 kN, Pu 0.4 kN, reference speed 17,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7304-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (17.4/9.5 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7304 BEP is the basic 20×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-BEP",
      "7304 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7304 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 19,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.425,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 BECBP is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 20×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 19 kN, C0 10 kN, Pu 0.425 kN.reference speed 17,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 140 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 18,000 r/min while thermal balance under catalogue load sets the 17,000 r/min reference; at dm ≈ 36.0 mm the corresponding dn is approximately 648k mm·r/min. Selection figures for 7304 BECBP: the static-to-dynamic ratio C0/C is 0.53, Pu 0.425 kN is about 2 % of C, and catalogue mass works out to roughly 7 g per millimetre of bore. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "small gear and metering pumps",
      "encoder and resolver mountings",
      "dental and laboratory high-speed rotors"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7304-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7304-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-BECBP?",
        "a": "7304 BECBP measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 19 kN, C0 10 kN, Pu 0.425 kN, reference speed 17,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7304-BECBP?",
        "a": "The 17,000 r/min reference (thermal) and 18,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7304-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7304 BEP is the basic 20×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-BECBP",
      "7304 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7304 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 19,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.425,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 BECBPH is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 20×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 19 kN, C0 10 kN, Pu 0.425 kN.reference speed 17,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 140 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 18,000 r/min while thermal balance under catalogue load sets the 17,000 r/min reference; at dm ≈ 36.0 mm the corresponding dn is approximately 648k mm·r/min. At the printed limiting speed of 18,000 r/min the mean pitch diameter dm ≈ 36.0 mm implies a dn value around 648k mm·r/min; the 17,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "servo and stepper motor shafts",
      "textile and wire-guide spindles",
      "small gear and metering pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "One 7304-BECBPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7304-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-BECBPH?",
        "a": "7304 BECBPH measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 19 kN, C0 10 kN, Pu 0.425 kN, reference speed 17,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7304-BECBPH?",
        "a": "The 17,000 r/min reference (thermal) and 18,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7304-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7304 BEP is the basic 20×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-BECBPH",
      "7304 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7304 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 19,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.425,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 BECBM is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 20×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 19 kN, C0 10 kN, Pu 0.425 kN.reference speed 17,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical), catalogue mass 140 g. Mass and section check: 140 g inside the 20×52×15 mm outline leaves a 16.0 mm radial section, and the 10 kN static rating is 0.53× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 0.425 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 19/10 kN ratings and 140 g mass this execution carries about 0.95 kN of C per millimetre of bore. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7304-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7304-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-BECBM?",
        "a": "7304 BECBM measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 19 kN, C0 10 kN, Pu 0.425 kN, reference speed 17,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7304-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 22,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7304-BECBM?",
        "a": "The 17,000 r/min reference (thermal) and 22,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (19/10 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7304 BEP is the basic 20×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-BECBM",
      "7304 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7304 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.475,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 BECBY is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 20×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 20.4 kN, C0 11.2 kN, Pu 0.475 kN.reference speed 17,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 140 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 18,000 r/min while thermal balance under catalogue load sets the 17,000 r/min reference; at dm ≈ 36.0 mm the corresponding dn is approximately 648k mm·r/min. Sizing arithmetic on the 20 mm bore: 20.4 kN C divided by the 16.0 mm radial section height gives 1.3 kN per section millimetre; the 140 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "dental and laboratory high-speed rotors",
      "miniature turbine and gyro drives",
      "high-speed engraving and routing spindles"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 20 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7304-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-BECBY?",
        "a": "7304 BECBY measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 20.4 kN, C0 11.2 kN, Pu 0.475 kN, reference speed 17,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7304-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.4/11.2 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7304 BEP shares the 20×52×15 mm angular-contact envelope, but catalogue C/C0 differ (20.4/11.2 kN vs 17.4/9.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-BECBY",
      "7304 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7304-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7304 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 20.8,
    "static_load_kN": 11.2,
    "fatigue_load_limit_kN": 0.475,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7304 ACCBM is SKF's 20 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 20×52×15 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 20.8 kN, C0 11.2 kN, Pu 0.475 kN.reference speed 19,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical), catalogue mass 140 g. Load balance: C0 11.2 kN against C 20.8 kN gives a 0.54 ratio, typical of a steep-angle axial-oriented design; Pu 0.475 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 20 mm bore: 20.8 kN C divided by the 16.0 mm radial section height gives 1.3 kN per section millimetre; the 140 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 19,000 r/min against a 26,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.73. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "textile and wire-guide spindles",
      "small gear and metering pumps",
      "encoder and resolver mountings"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 20 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "One 7304-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7304-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The 25° AC angle of 7304-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7304-ACCBM?",
        "a": "7304 ACCBM measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 140 g. SKF 17000 ratings: C 20.8 kN, C0 11.2 kN, Pu 0.475 kN, reference speed 19,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7304-ACCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 26,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7304-ACCBM?",
        "a": "The 19,000 r/min reference (thermal) and 26,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; 7304 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (20.8/11.2 kN vs 32/21.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7304 BEP shares the 20×52×15 mm angular-contact envelope, but catalogue C/C0 differ (20.8/11.2 kN vs 17.4/9.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7304-ACCBM",
      "7304 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7205 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.8,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BE-2RZP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 14.8 kN, C0 9.3 kN, Pu 0.4 kN.reference speed 16,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 130 g. At the printed limiting speed of 12,000 r/min the mean pitch diameter dm ≈ 38.5 mm implies a dn value around 462k mm·r/min; the 16,000 r/min reference speed is the thermal-planning figure under catalogue load. The 0.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 14.8/9.3 kN ratings and 130 g mass this execution carries about 0.59 kN of C per millimetre of bore. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7205-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7205-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BE-2RZP?",
        "a": "7205 BE-2RZP measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 14.8 kN, C0 9.3 kN, Pu 0.4 kN, reference speed 16,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What minimum axial load does 7205-BE-2RZP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (14.8/9.3 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (14.8/9.3 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BE-2RZP",
      "7205 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7205 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.8,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BEP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 14.8 kN, C0 9.3 kN, Pu 0.4 kN.reference speed 16,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 130 g. At the printed limiting speed of 15,000 r/min the mean pitch diameter dm ≈ 38.5 mm implies a dn value around 578k mm·r/min; the 16,000 r/min reference speed is the thermal-planning figure under catalogue load. The 0.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 14.8/9.3 kN ratings and 130 g mass this execution carries about 0.59 kN of C per millimetre of bore. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "One 7205-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7205-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7205 BEP as the single basic pa66 execution; the other order numbers of the 7205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BEP?",
        "a": "7205 BEP measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 14.8 kN, C0 9.3 kN, Pu 0.4 kN, reference speed 16,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7205-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (14.8/9.3 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (14.8/9.3 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BEP",
      "7205 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BEY",
    "brand": "SKF",
    "manufacturer_designation": "7205 BEY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 14.8,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BEY is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 14.8 kN, C0 9.3 kN, Pu 0.4 kN.reference speed 16,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 130 g. Selection figures for 7205 BEY: the static-to-dynamic ratio C0/C is 0.63, Pu 0.4 kN is about 3 % of C, and catalogue mass works out to roughly 5 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 15,000 r/min while thermal balance under catalogue load sets the 16,000 r/min reference; at dm ≈ 38.5 mm the corresponding dn is approximately 578k mm·r/min. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Ordering note: BEY is the basic single bearing with the stamped brass strip cage (Y) — light and oil-additive tolerant, but not ground on the side faces for set mounting; order BECBY for a universally matchable stamped-brass unit.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7205-BEY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Do not mix execution classes inside one set: a universally matchable BEY unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7205-BEY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7205 BEY as the single basic stamped brass execution; the other order numbers of the 7205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BEY?",
        "a": "7205 BEY measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 14.8 kN, C0 9.3 kN, Pu 0.4 kN, reference speed 16,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7205-BEY?",
        "a": "The 16,000 r/min reference (thermal) and 15,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7205-BEY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (14.8/9.3 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (14.8/9.3 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BEY",
      "7205 BEY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7205 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.43,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BECBP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 15.6 kN, C0 10 kN, Pu 0.43 kN.reference speed 16,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 130 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 17,000 r/min while thermal balance under catalogue load sets the 16,000 r/min reference; at dm ≈ 38.5 mm the corresponding dn is approximately 655k mm·r/min. Selection figures for 7205 BECBP: the static-to-dynamic ratio C0/C is 0.64, Pu 0.43 kN is about 3 % of C, and catalogue mass works out to roughly 5 g per millimetre of bore. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7205-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BECBP?",
        "a": "7205 BECBP measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 15.6 kN, C0 10 kN, Pu 0.43 kN, reference speed 16,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7205-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BECBP",
      "7205 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7205 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.43,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BECBY is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 15.6 kN, C0 10 kN, Pu 0.43 kN.reference speed 16,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 130 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 17,000 r/min while thermal balance under catalogue load sets the 16,000 r/min reference; at dm ≈ 38.5 mm the corresponding dn is approximately 655k mm·r/min. Sizing arithmetic on the 25 mm bore: 15.6 kN C divided by the 13.5 mm radial section height gives 1.2 kN per section millimetre; the 130 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "At 25 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "At 25 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "At 25 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7205-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BECBY?",
        "a": "7205 BECBY measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 15.6 kN, C0 10 kN, Pu 0.43 kN, reference speed 16,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which fits should I use for 7205-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7205-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 17,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BECBY",
      "7205 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7205 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.43,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BECBM is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 15.6 kN, C0 10 kN, Pu 0.43 kN.reference speed 16,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 130 g. Mass and section check: 130 g inside the 25×52×15 mm outline leaves a 13.5 mm radial section, and the 10 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 0.43 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 15.6/10 kN ratings and 130 g mass this execution carries about 0.62 kN of C per millimetre of bore. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7205-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BECBM?",
        "a": "7205 BECBM measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 15.6 kN, C0 10 kN, Pu 0.43 kN, reference speed 16,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7205-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7205-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BECBM",
      "7205 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7205 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 15.6,
    "static_load_kN": 10,
    "fatigue_load_limit_kN": 0.43,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 BECBPH is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 25×52×15 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 15.6 kN, C0 10 kN, Pu 0.43 kN.reference speed 16,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 130 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 17,000 r/min while thermal balance under catalogue load sets the 16,000 r/min reference; at dm ≈ 38.5 mm the corresponding dn is approximately 655k mm·r/min. At the printed limiting speed of 17,000 r/min the mean pitch diameter dm ≈ 38.5 mm implies a dn value around 655k mm·r/min; the 16,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7205-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-BECBPH?",
        "a": "7205 BECBPH measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 15.6 kN, C0 10 kN, Pu 0.43 kN, reference speed 16,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7205-BECBPH?",
        "a": "The 16,000 r/min reference (thermal) and 17,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7205-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×15 mm envelope with catalogue ratings within 10 %; 7205 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (15.6/10 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7205 BEP is the basic 25×52×15 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-BECBPH",
      "7205 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7205-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7205 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 18,
    "static_load_kN": 11.4,
    "fatigue_load_limit_kN": 0.49,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 26000,
    "max_rpm": 26000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7205 ACCBM is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 25×52×15 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 18 kN, C0 11.4 kN, Pu 0.49 kN.reference speed 17,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical), catalogue mass 130 g. Load balance: C0 11.4 kN against C 18 kN gives a 0.63 ratio, typical of a steep-angle axial-oriented design; Pu 0.49 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 25 mm bore: 18 kN C divided by the 13.5 mm radial section height gives 1.3 kN per section millimetre; the 130 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 17,000 r/min against a 26,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.65. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "One 7205-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The 25° AC angle of 7205-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7205-ACCBM?",
        "a": "7205 ACCBM measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 130 g. SKF 17000 ratings: C 18 kN, C0 11.4 kN, Pu 0.49 kN, reference speed 17,000 r/min (thermal) and limiting speed 26,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7205-ACCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 26,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7205-ACCBM?",
        "a": "The 17,000 r/min reference (thermal) and 26,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 14.8/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 14.8/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 14.8/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-205-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (18/11.4 kN vs 27/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7205 BEP shares the 25×52×15 mm angular-contact envelope, but catalogue C/C0 differ (18/11.4 kN vs 14.8/9.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7205-ACCBM",
      "7205 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7305 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 24.2,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.6,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BE-2RZP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 24.2 kN, C0 14 kN, Pu 0.6 kN.reference speed 14,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 230 g. The 0.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 24.2/14 kN ratings and 230 g mass this execution carries about 0.97 kN of C per millimetre of bore. Sizing arithmetic on the 25 mm bore: 24.2 kN C divided by the 18.5 mm radial section height gives 1.3 kN per section millimetre; the 230 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7305-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7305-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BE-2RZP?",
        "a": "7305 BE-2RZP measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 24.2 kN, C0 14 kN, Pu 0.6 kN, reference speed 14,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7305-BE-2RZP?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BE-2RZP",
      "7305 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7305 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 24.2,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.6,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BEP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 24.2 kN, C0 14 kN, Pu 0.6 kN.reference speed 14,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), which coincide for this size, catalogue mass 230 g. The 0.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 24.2/14 kN ratings and 230 g mass this execution carries about 0.97 kN of C per millimetre of bore. Sizing arithmetic on the 25 mm bore: 24.2 kN C divided by the 18.5 mm radial section height gives 1.3 kN per section millimetre; the 230 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 25 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7305-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7305 BEP as the single basic pa66 execution; the other order numbers of the 7305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BEP?",
        "a": "7305 BEP measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 24.2 kN, C0 14 kN, Pu 0.6 kN, reference speed 14,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Can one 7305-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7305-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BEP",
      "7305 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BEY",
    "brand": "SKF",
    "manufacturer_designation": "7305 BEY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 24.2,
    "static_load_kN": 14,
    "fatigue_load_limit_kN": 0.6,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BEY is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 24.2 kN, C0 14 kN, Pu 0.6 kN.reference speed 14,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), which coincide for this size, catalogue mass 230 g. Sizing arithmetic on the 25 mm bore: 24.2 kN C divided by the 18.5 mm radial section height gives 1.3 kN per section millimetre; the 230 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 14 kN against C 24.2 kN gives a 0.58 ratio, typical of a steep-angle axial-oriented design; Pu 0.6 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Ordering note: BEY is the basic single bearing with the stamped brass strip cage (Y) — light and oil-additive tolerant, but not ground on the side faces for set mounting; order BECBY for a universally matchable stamped-brass unit.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7305-BEY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7305 BEY as the single basic stamped brass execution; the other order numbers of the 7305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BEY?",
        "a": "7305 BEY measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 24.2 kN, C0 14 kN, Pu 0.6 kN, reference speed 14,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.."
      },
      {
        "q": "Which grease and fill for 7305-BEY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 14,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7305-BEY?",
        "a": "The 14,000 r/min reference (thermal) and 14,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (24.2/14 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BEY",
      "7305 BEY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7305 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 15.3,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BECBP is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 26.5 kN, C0 15.3 kN, Pu 0.655 kN.reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 230 g. Mass and section check: 230 g inside the 25×62×17 mm outline leaves a 18.5 mm radial section, and the 15.3 kN static rating is 0.58× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 0.655 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 26.5/15.3 kN ratings and 230 g mass this execution carries about 1.06 kN of C per millimetre of bore. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7305-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BECBP?",
        "a": "7305 BECBP measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 26.5 kN, C0 15.3 kN, Pu 0.655 kN, reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7305-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 15,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7305-BECBP?",
        "a": "The 14,000 r/min reference (thermal) and 15,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BECBP",
      "7305 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7305 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 15.3,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BECBPH is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 26.5 kN, C0 15.3 kN, Pu 0.655 kN.reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 230 g. The 0.655 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 26.5/15.3 kN ratings and 230 g mass this execution carries about 1.06 kN of C per millimetre of bore. Selection figures for 7305 BECBPH: the static-to-dynamic ratio C0/C is 0.58, Pu 0.655 kN is about 2 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7305-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BECBPH?",
        "a": "7305 BECBPH measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 26.5 kN, C0 15.3 kN, Pu 0.655 kN, reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7305-BECBPH?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BECBPH",
      "7305 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7305 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 15.3,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BECBY is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 26.5 kN, C0 15.3 kN, Pu 0.655 kN.reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 230 g. Sizing arithmetic on the 25 mm bore: 26.5 kN C divided by the 18.5 mm radial section height gives 1.4 kN per section millimetre; the 230 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. The 0.655 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 26.5/15.3 kN ratings and 230 g mass this execution carries about 1.06 kN of C per millimetre of bore. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 25 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7305-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BECBY?",
        "a": "7305 BECBY measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 26.5 kN, C0 15.3 kN, Pu 0.655 kN, reference speed 14,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Can one 7305-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7305-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BECBY",
      "7305 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7305 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 26.5,
    "static_load_kN": 15.3,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 BECBM is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 25×62×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 26.5 kN, C0 15.3 kN, Pu 0.655 kN.reference speed 14,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), catalogue mass 230 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 19,000 r/min while thermal balance under catalogue load sets the 14,000 r/min reference; at dm ≈ 43.5 mm the corresponding dn is approximately 827k mm·r/min. Selection figures for 7305 BECBM: the static-to-dynamic ratio C0/C is 0.58, Pu 0.655 kN is about 2 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7305-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 17 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 25 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7305-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-BECBM?",
        "a": "7305 BECBM measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 26.5 kN, C0 15.3 kN, Pu 0.655 kN, reference speed 14,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7305-BECBM?",
        "a": "The 14,000 r/min reference (thermal) and 19,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7305-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; 7305 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (26.5/15.3 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7305 BEP is the basic 25×62×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-BECBM",
      "7305 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7305-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7305 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 29,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.72,
    "reference_speed_rpm": 15000,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 230,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7305 ACCBM is SKF's 25 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 25×62×17 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 29 kN, C0 17 kN, Pu 0.72 kN.reference speed 15,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical), catalogue mass 230 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 22,000 r/min while thermal balance under catalogue load sets the 15,000 r/min reference; at dm ≈ 43.5 mm the corresponding dn is approximately 957k mm·r/min. Selection figures for 7305 ACCBM: the static-to-dynamic ratio C0/C is 0.59, Pu 0.72 kN is about 2 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 15,000 r/min against a 22,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.68. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7305-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The 25° AC angle of 7305-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7305-ACCBM?",
        "a": "7305 ACCBM measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 230 g. SKF 17000 ratings: C 29 kN, C0 17 kN, Pu 0.72 kN, reference speed 15,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7305-ACCBM?",
        "a": "The 15,000 r/min reference (thermal) and 22,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7305-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (29/17 kN vs 42.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7305 BEP shares the 25×62×17 mm angular-contact envelope, but catalogue C/C0 differ (29/17 kN vs 24.2/14 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7305-ACCBM",
      "7305 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7206 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.61,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 260,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 BE-2RZP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 30×62×16 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 22.5 kN, C0 14.3 kN, Pu 0.61 kN.reference speed 13,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 260 g. Load balance: C0 14.3 kN against C 22.5 kN gives a 0.64 ratio, typical of a steep-angle axial-oriented design; Pu 0.61 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 260 g inside the 30×62×16 mm outline leaves a 16.0 mm radial section, and the 14.3 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 13,000 r/min against a 10,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.30. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "One 7206-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7206-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7206-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7206-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-BE-2RZP?",
        "a": "7206 BE-2RZP measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 260 g. SKF 17000 ratings: C 22.5 kN, C0 14.3 kN, Pu 0.61 kN, reference speed 13,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Which grease and fill for 7206-BE-2RZP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 10,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7206-BE-2RZP?",
        "a": "The 13,000 r/min reference (thermal) and 10,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 25.5/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7206 BEP is the basic 30×62×16 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-BE-2RZP",
      "7206 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7206 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 22.5,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.61,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 BEP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 30×62×16 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 22.5 kN, C0 14.3 kN, Pu 0.61 kN.reference speed 13,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), which coincide for this size, catalogue mass 200 g. Load balance: C0 14.3 kN against C 22.5 kN gives a 0.64 ratio, typical of a steep-angle axial-oriented design; Pu 0.61 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 200 g inside the 30×62×16 mm outline leaves a 16.0 mm radial section, and the 14.3 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 13,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7206-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7206-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7206 BEP as the single basic pa66 execution; the other order numbers of the 7206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-BEP?",
        "a": "7206 BEP measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 200 g. SKF 17000 ratings: C 22.5 kN, C0 14.3 kN, Pu 0.61 kN, reference speed 13,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7206-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 30 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 25.5/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (22.5/14.3 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7206 BEP is the basic 30×62×16 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-BEP",
      "7206 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7206 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 24,
    "static_load_kN": 15.6,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 BECBP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 30×62×16 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 24 kN, C0 15.6 kN, Pu 0.655 kN.reference speed 13,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 200 g. The 0.655 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 24/15.6 kN ratings and 200 g mass this execution carries about 0.80 kN of C per millimetre of bore. Load balance: C0 15.6 kN against C 24 kN gives a 0.65 ratio, typical of a steep-angle axial-oriented design; Pu 0.655 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 13,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "One 7206-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7206-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-BECBP?",
        "a": "7206 BECBP measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 200 g. SKF 17000 ratings: C 24 kN, C0 15.6 kN, Pu 0.655 kN, reference speed 13,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7206-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 14,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7206-BECBP?",
        "a": "The 13,000 r/min reference (thermal) and 14,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7206 BEP is the basic 30×62×16 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-BECBP",
      "7206 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7206 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 24,
    "static_load_kN": 15.6,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 BECBPH is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 30×62×16 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 24 kN, C0 15.6 kN, Pu 0.655 kN.reference speed 13,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 200 g. Load balance: C0 15.6 kN against C 24 kN gives a 0.65 ratio, typical of a steep-angle axial-oriented design; Pu 0.655 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 14,000 r/min while thermal balance under catalogue load sets the 13,000 r/min reference; at dm ≈ 46.0 mm the corresponding dn is approximately 644k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 13,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "One 7206-BECBPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7206-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BECBPH unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7206-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-BECBPH?",
        "a": "7206 BECBPH measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 200 g. SKF 17000 ratings: C 24 kN, C0 15.6 kN, Pu 0.655 kN, reference speed 13,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7206-BECBPH?",
        "a": "With a rotating inner ring use roughly k5 on the 30 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7206 BEP is the basic 30×62×16 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-BECBPH",
      "7206 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7206 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 24,
    "static_load_kN": 15.6,
    "fatigue_load_limit_kN": 0.655,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 BECBM is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 30×62×16 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 24 kN, C0 15.6 kN, Pu 0.655 kN.reference speed 13,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 200 g. Envelope economics: the 16 mm width over a 16.0 mm section yields 1.00 mm of ring width per section millimetre, and the bearing weighs 200 g for 24 kN of dynamic capacity — about 8 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 18,000 r/min while thermal balance under catalogue load sets the 13,000 r/min reference; at dm ≈ 46.0 mm the corresponding dn is approximately 828k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 13,000 r/min against a 18,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.72. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 30 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7206-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-BECBM?",
        "a": "7206 BECBM measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 200 g. SKF 17000 ratings: C 24 kN, C0 15.6 kN, Pu 0.655 kN, reference speed 13,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7206-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (24/15.6 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7206 BEP is the basic 30×62×16 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-BECBM",
      "7206 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7206 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 25.5,
    "static_load_kN": 17,
    "fatigue_load_limit_kN": 0.71,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 BECBY is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 30×62×16 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 25.5 kN, C0 17 kN, Pu 0.71 kN.reference speed 13,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 200 g. Mass and section check: 200 g inside the 30×62×16 mm outline leaves a 16.0 mm radial section, and the 17 kN static rating is 0.67× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 17 kN against C 25.5 kN gives a 0.67 ratio, typical of a steep-angle axial-oriented design; Pu 0.71 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 13,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7206-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "At 30 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Assign interference to the rotating ring — roughly k5 on a 30 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7206-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-BECBY?",
        "a": "7206 BECBY measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 200 g. SKF 17000 ratings: C 25.5 kN, C0 17 kN, Pu 0.71 kN, reference speed 13,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7206-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 14,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7206-BECBY?",
        "a": "The 13,000 r/min reference (thermal) and 14,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (25.5/17 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (25.5/17 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (25.5/17 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (25.5/17 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7206 BEP shares the 30×62×16 mm angular-contact envelope, but catalogue C/C0 differ (25.5/17 kN vs 22.5/14.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-BECBY",
      "7206 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7206-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7206 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 27.5,
    "static_load_kN": 17.3,
    "fatigue_load_limit_kN": 0.735,
    "reference_speed_rpm": 15000,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7206 ACCBM is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 30×62×16 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 27.5 kN, C0 17.3 kN, Pu 0.735 kN.reference speed 15,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical), catalogue mass 200 g. Selection figures for 7206 ACCBM: the static-to-dynamic ratio C0/C is 0.63, Pu 0.735 kN is about 3 % of C, and catalogue mass works out to roughly 7 g per millimetre of bore. At the printed limiting speed of 20,000 r/min the mean pitch diameter dm ≈ 46.0 mm implies a dn value around 920k mm·r/min; the 15,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 62 over bore 30 is a 2.07× step for this size, and the 16 mm width gives a bore/width ratio of 1.88; use these ratios when housing space around the 30 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7206-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The 25° AC angle of 7206-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7206-ACCBM?",
        "a": "7206 ACCBM measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 200 g. SKF 17000 ratings: C 27.5 kN, C0 17.3 kN, Pu 0.735 kN, reference speed 15,000 r/min (thermal) and limiting speed 20,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7206-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; 7206 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (27.5/17.3 kN vs 37.5/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7206 BEP shares the 30×62×16 mm angular-contact envelope, but catalogue C/C0 differ (27.5/17.3 kN vs 22.5/14.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7206-ACCBM",
      "7206 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7306 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 19.3,
    "fatigue_load_limit_kN": 0.815,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 BE-2RZP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 32.5 kN, C0 19.3 kN, Pu 0.815 kN.reference speed 12,000 r/min (thermal) and limiting speed 9,500 r/min (mechanical), catalogue mass 350 g. Selection figures for 7306 BE-2RZP: the static-to-dynamic ratio C0/C is 0.59, Pu 0.815 kN is about 3 % of C, and catalogue mass works out to roughly 12 g per millimetre of bore. Load balance: C0 19.3 kN against C 32.5 kN gives a 0.59 ratio, typical of a steep-angle axial-oriented design; Pu 0.815 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 9,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.26. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "One 7306-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 30 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7306-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7306-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-BE-2RZP?",
        "a": "7306 BE-2RZP measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 350 g. SKF 17000 ratings: C 32.5 kN, C0 19.3 kN, Pu 0.815 kN, reference speed 12,000 r/min (thermal) and limiting speed 9,500 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Which fits should I use for 7306-BE-2RZP?",
        "a": "With a rotating inner ring use roughly k5 on the 30 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7306-BE-2RZP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 9,500 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 37.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7306 BEP is the basic 30×72×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-BE-2RZP",
      "7306 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7306 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 19.3,
    "fatigue_load_limit_kN": 0.815,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 BEP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 32.5 kN, C0 19.3 kN, Pu 0.815 kN.reference speed 12,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), which coincide for this size, catalogue mass 340 g. Selection figures for 7306 BEP: the static-to-dynamic ratio C0/C is 0.59, Pu 0.815 kN is about 3 % of C, and catalogue mass works out to roughly 11 g per millimetre of bore. Load balance: C0 19.3 kN against C 32.5 kN gives a 0.59 ratio, typical of a steep-angle axial-oriented design; Pu 0.815 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 12,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Assign interference to the rotating ring — roughly k5 on a 30 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7306-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7306 BEP as the single basic pa66 execution; the other order numbers of the 7306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-BEP?",
        "a": "7306 BEP measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 340 g. SKF 17000 ratings: C 32.5 kN, C0 19.3 kN, Pu 0.815 kN, reference speed 12,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which fits should I use for 7306-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 30 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7306-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 12,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 37.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (32.5/19.3 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7306 BEP is the basic 30×72×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-BEP",
      "7306 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7306 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 21.2,
    "fatigue_load_limit_kN": 0.9,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 BECBP is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 35.5 kN, C0 21.2 kN, Pu 0.9 kN.reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 340 g. Envelope economics: the 19 mm width over a 21.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 340 g for 35.5 kN of dynamic capacity — about 10 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 13,000 r/min while thermal balance under catalogue load sets the 12,000 r/min reference; at dm ≈ 51.0 mm the corresponding dn is approximately 663k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 30 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7306-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-BECBP?",
        "a": "7306 BECBP measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 340 g. SKF 17000 ratings: C 35.5 kN, C0 21.2 kN, Pu 0.9 kN, reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7306-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 30 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7306-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 13,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7306 BEP is the basic 30×72×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-BECBP",
      "7306 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7306 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 21.2,
    "fatigue_load_limit_kN": 0.9,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 BEGAPH is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 35.5 kN, C0 21.2 kN, Pu 0.9 kN.reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 340 g. Envelope economics: the 19 mm width over a 21.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 340 g for 35.5 kN of dynamic capacity — about 10 g per rated kN. Selection figures for 7306 BEGAPH: the static-to-dynamic ratio C0/C is 0.60, Pu 0.9 kN is about 3 % of C, and catalogue mass works out to roughly 11 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEGAPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 30 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7306-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-BEGAPH?",
        "a": "7306 BEGAPH measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 340 g. SKF 17000 ratings: C 35.5 kN, C0 21.2 kN, Pu 0.9 kN, reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What minimum axial load does 7306-BEGAPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7306 BEP is the basic 30×72×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-BEGAPH",
      "7306 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7306 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 21.2,
    "fatigue_load_limit_kN": 0.9,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 BECBM is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 35.5 kN, C0 21.2 kN, Pu 0.9 kN.reference speed 12,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical), catalogue mass 340 g. The 0.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 35.5/21.2 kN ratings and 340 g mass this execution carries about 1.18 kN of C per millimetre of bore. Load balance: C0 21.2 kN against C 35.5 kN gives a 0.60 ratio, typical of a steep-angle axial-oriented design; Pu 0.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 16,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.75. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7306-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-BECBM?",
        "a": "7306 BECBM measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 340 g. SKF 17000 ratings: C 35.5 kN, C0 21.2 kN, Pu 0.9 kN, reference speed 12,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7306-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7306-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (35.5/21.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7306 BEP is the basic 30×72×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-BECBM",
      "7306 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7306 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 37.5,
    "static_load_kN": 23.2,
    "fatigue_load_limit_kN": 0.98,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 BECBY is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 30×72×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 37.5 kN, C0 23.2 kN, Pu 0.98 kN.reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 340 g. Envelope economics: the 19 mm width over a 21.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 340 g for 37.5 kN of dynamic capacity — about 9 g per rated kN. Mass and section check: 340 g inside the 30×72×19 mm outline leaves a 21.0 mm radial section, and the 23.2 kN static rating is 0.62× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7306-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Assign interference to the rotating ring — roughly k5 on a 30 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7306-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7306-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-BECBY?",
        "a": "7306 BECBY measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 340 g. SKF 17000 ratings: C 37.5 kN, C0 23.2 kN, Pu 0.98 kN, reference speed 12,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which fits should I use for 7306-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 30 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7306-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 13,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (37.5/23.2 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (37.5/23.2 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (37.5/23.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (37.5/23.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (37.5/23.2 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7306 BEP shares the 30×72×19 mm angular-contact envelope, but catalogue C/C0 differ (37.5/23.2 kN vs 32.5/19.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-BECBY",
      "7306 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7306-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7306 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 39,
    "static_load_kN": 23.6,
    "fatigue_load_limit_kN": 1,
    "reference_speed_rpm": 13000,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 340,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7306 ACCBM is SKF's 30 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 30×72×19 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 39 kN, C0 23.6 kN, Pu 1 kN.reference speed 13,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical), catalogue mass 340 g. The 1 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 39/23.6 kN ratings and 340 g mass this execution carries about 1.30 kN of C per millimetre of bore. Load balance: C0 23.6 kN against C 39 kN gives a 0.61 ratio, typical of a steep-angle axial-oriented design; Pu 1 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 72 over bore 30 is a 2.40× step for this size, and the 19 mm width gives a bore/width ratio of 1.58; use these ratios when housing space around the 30 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7306-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The 25° AC angle of 7306-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7306-ACCBM?",
        "a": "7306 ACCBM measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 340 g. SKF 17000 ratings: C 39 kN, C0 23.6 kN, Pu 1 kN, reference speed 13,000 r/min (thermal) and limiting speed 19,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7306-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7306-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; 7306 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (39/23.6 kN vs 53/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7306 BEP shares the 30×72×19 mm angular-contact envelope, but catalogue C/C0 differ (39/23.6 kN vs 32.5/19.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7306-ACCBM",
      "7306 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7207 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 29.1,
    "static_load_kN": 19,
    "fatigue_load_limit_kN": 0.815,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7207 BE-2RZP is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 35×72×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 29.1 kN, C0 19 kN, Pu 0.815 kN.reference speed 11,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 350 g. Selection figures for 7207 BE-2RZP: the static-to-dynamic ratio C0/C is 0.65, Pu 0.815 kN is about 3 % of C, and catalogue mass works out to roughly 10 g per millimetre of bore. Load balance: C0 19 kN against C 29.1 kN gives a 0.65 ratio, typical of a steep-angle axial-oriented design; Pu 0.815 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 9,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.22. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 35 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7207-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7207-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7207-BE-2RZP?",
        "a": "7207 BE-2RZP measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 350 g. SKF 17000 ratings: C 29.1 kN, C0 19 kN, Pu 0.815 kN, reference speed 11,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What minimum axial load does 7207-BE-2RZP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (29.1/19 kN vs 32.5/22.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (29.1/19 kN vs 35.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (29.1/19 kN vs 49/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7207 BEP is the basic 35×72×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207-BE-2RZP",
      "7207 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7207 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 29.1,
    "static_load_kN": 19,
    "fatigue_load_limit_kN": 0.815,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7207 BEP is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 35×72×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 29.1 kN, C0 19 kN, Pu 0.815 kN.reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size, catalogue mass 280 g. Selection figures for 7207 BEP: the static-to-dynamic ratio C0/C is 0.65, Pu 0.815 kN is about 3 % of C, and catalogue mass works out to roughly 8 g per millimetre of bore. Load balance: C0 19 kN against C 29.1 kN gives a 0.65 ratio, typical of a steep-angle axial-oriented design; Pu 0.815 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 11,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7207-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7207 BEP as the single basic pa66 execution; the other order numbers of the 7207 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7207-BEP?",
        "a": "7207 BEP measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 280 g. SKF 17000 ratings: C 29.1 kN, C0 19 kN, Pu 0.815 kN, reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7207-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (29.1/19 kN vs 32.5/22.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (29.1/19 kN vs 35.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (29.1/19 kN vs 49/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7207 BEP is the basic 35×72×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207-BEP",
      "7207 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7207 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 31,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.88,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7207 BECBP is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 35×72×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 31 kN, C0 20.8 kN, Pu 0.88 kN.reference speed 11,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 280 g. Envelope economics: the 17 mm width over a 18.5 mm section yields 0.92 mm of ring width per section millimetre, and the bearing weighs 280 g for 31 kN of dynamic capacity — about 9 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 12,000 r/min while thermal balance under catalogue load sets the 11,000 r/min reference; at dm ≈ 53.5 mm the corresponding dn is approximately 642k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 12,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "One 7207-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7207-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7207-BECBP?",
        "a": "7207 BECBP measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 280 g. SKF 17000 ratings: C 31 kN, C0 20.8 kN, Pu 0.88 kN, reference speed 11,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7207-BECBP?",
        "a": "The 11,000 r/min reference (thermal) and 12,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7207-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (31/20.8 kN vs 35.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (31/20.8 kN vs 49/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7207 BEP is the basic 35×72×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207-BECBP",
      "7207 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7207 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 31,
    "static_load_kN": 20.8,
    "fatigue_load_limit_kN": 0.88,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7207 BECBM is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 35×72×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 31 kN, C0 20.8 kN, Pu 0.88 kN.reference speed 11,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 280 g. The 0.88 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 31/20.8 kN ratings and 280 g mass this execution carries about 0.89 kN of C per millimetre of bore. Load balance: C0 20.8 kN against C 31 kN gives a 0.67 ratio, typical of a steep-angle axial-oriented design; Pu 0.88 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 15,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.73. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7207-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7207-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7207-BECBM?",
        "a": "7207 BECBM measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 280 g. SKF 17000 ratings: C 31 kN, C0 20.8 kN, Pu 0.88 kN, reference speed 11,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7207-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 35 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (31/20.8 kN vs 35.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (31/20.8 kN vs 49/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7207 BEP is the basic 35×72×17 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207-BECBM",
      "7207 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7207 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 32.5,
    "static_load_kN": 22.4,
    "fatigue_load_limit_kN": 0.95,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7207 BECBY is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 35×72×17 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 32.5 kN, C0 22.4 kN, Pu 0.95 kN.reference speed 11,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 280 g. Envelope economics: the 17 mm width over a 18.5 mm section yields 0.92 mm of ring width per section millimetre, and the bearing weighs 280 g for 32.5 kN of dynamic capacity — about 9 g per rated kN. Mass and section check: 280 g inside the 35×72×17 mm outline leaves a 18.5 mm radial section, and the 22.4 kN static rating is 0.69× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 12,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7207-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7207-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7207-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7207-BECBY?",
        "a": "7207 BECBY measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 280 g. SKF 17000 ratings: C 32.5 kN, C0 22.4 kN, Pu 0.95 kN, reference speed 11,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7207-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (32.5/22.4 kN vs 29.1/19 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (32.5/22.4 kN vs 29.1/19 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (32.5/22.4 kN vs 49/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7207 BEP shares the 35×72×17 mm angular-contact envelope, but catalogue C/C0 differ (32.5/22.4 kN vs 29.1/19 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207-BECBY",
      "7207 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7207-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7207 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 35.5,
    "static_load_kN": 23.2,
    "fatigue_load_limit_kN": 0.98,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 280,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7207 ACCBM is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 35×72×17 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 35.5 kN, C0 23.2 kN, Pu 0.98 kN.reference speed 12,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 280 g. The 0.98 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 35.5/23.2 kN ratings and 280 g mass this execution carries about 1.01 kN of C per millimetre of bore. Load balance: C0 23.2 kN against C 35.5 kN gives a 0.65 ratio, typical of a steep-angle axial-oriented design; Pu 0.98 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 72 over bore 35 is a 2.06× step for this size, and the 17 mm width gives a bore/width ratio of 2.06; use these ratios when housing space around the 35 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7207-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly k5 on a 35 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The 25° AC angle of 7207-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7207-ACCBM?",
        "a": "7207 ACCBM measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 280 g. SKF 17000 ratings: C 35.5 kN, C0 23.2 kN, Pu 0.98 kN, reference speed 12,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7207-ACCBM?",
        "a": "With a rotating inner ring use roughly k5 on the 35 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (35.5/23.2 kN vs 29.1/19 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (35.5/23.2 kN vs 29.1/19 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (35.5/23.2 kN vs 31/20.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (35.5/23.2 kN vs 31/20.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×17 mm envelope with catalogue ratings within 10 %; 7207 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-207-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (35.5/23.2 kN vs 49/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7207 BEP shares the 35×72×17 mm angular-contact envelope, but catalogue C/C0 differ (35.5/23.2 kN vs 29.1/19 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7207-ACCBM",
      "7207 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7307 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 24.5,
    "fatigue_load_limit_kN": 1.04,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 BE-2RZP is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 39 kN, C0 24.5 kN, Pu 1.04 kN.reference speed 11,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 450 g. Load balance: C0 24.5 kN against C 39 kN gives a 0.63 ratio, typical of a steep-angle axial-oriented design; Pu 1.04 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 450 g inside the 35×80×21 mm outline leaves a 22.5 mm radial section, and the 24.5 kN static rating is 0.63× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 8,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.29. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7307-BE-2RZP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Assign interference to the rotating ring — roughly k5 on a 35 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7307-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7307-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-BE-2RZP?",
        "a": "7307 BE-2RZP measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 39 kN, C0 24.5 kN, Pu 1.04 kN, reference speed 11,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Can one 7307-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7307-BE-2RZP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7307 BEP is the basic 35×80×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-BE-2RZP",
      "7307 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7307 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 39,
    "static_load_kN": 24.5,
    "fatigue_load_limit_kN": 1.04,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 BEP is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 39 kN, C0 24.5 kN, Pu 1.04 kN.reference speed 11,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 450 g. Load balance: C0 24.5 kN against C 39 kN gives a 0.63 ratio, typical of a steep-angle axial-oriented design; Pu 1.04 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 450 g inside the 35×80×21 mm outline leaves a 22.5 mm radial section, and the 24.5 kN static rating is 0.63× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 10,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.10. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7307-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7307 BEP as the single basic pa66 execution; the other order numbers of the 7307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-BEP?",
        "a": "7307 BEP measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 39 kN, C0 24.5 kN, Pu 1.04 kN, reference speed 11,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7307-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 10,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7307-BEP?",
        "a": "The 11,000 r/min reference (thermal) and 10,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (39/24.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7307 BEP is the basic 35×80×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-BEP",
      "7307 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7307 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 26.5,
    "fatigue_load_limit_kN": 1.14,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 BECBP is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 41.5 kN, C0 26.5 kN, Pu 1.14 kN.reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size, catalogue mass 450 g. The 1.14 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 41.5/26.5 kN ratings and 450 g mass this execution carries about 1.19 kN of C per millimetre of bore. Load balance: C0 26.5 kN against C 41.5 kN gives a 0.64 ratio, typical of a steep-angle axial-oriented design; Pu 1.14 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 11,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7307-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7307-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7307-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-BECBP?",
        "a": "7307 BECBP measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 41.5 kN, C0 26.5 kN, Pu 1.14 kN, reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7307-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7307-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7307 BEP is the basic 35×80×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-BECBP",
      "7307 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7307 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 26.5,
    "fatigue_load_limit_kN": 1.14,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 BECBY is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 41.5 kN, C0 26.5 kN, Pu 1.14 kN.reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size, catalogue mass 450 g. Mass and section check: 450 g inside the 35×80×21 mm outline leaves a 22.5 mm radial section, and the 26.5 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 26.5 kN against C 41.5 kN gives a 0.64 ratio, typical of a steep-angle axial-oriented design; Pu 1.14 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 11,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7307-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7307-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-BECBY?",
        "a": "7307 BECBY measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 41.5 kN, C0 26.5 kN, Pu 1.14 kN, reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Can one 7307-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7307-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7307 BEP is the basic 35×80×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-BECBY",
      "7307 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7307 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 26.5,
    "fatigue_load_limit_kN": 1.14,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 BEGAPH is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 41.5 kN, C0 26.5 kN, Pu 1.14 kN.reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size, catalogue mass 450 g. Load balance: C0 26.5 kN against C 41.5 kN gives a 0.64 ratio, typical of a steep-angle axial-oriented design; Pu 1.14 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 11,000 r/min while thermal balance under catalogue load sets the 11,000 r/min reference; at dm ≈ 57.5 mm the corresponding dn is approximately 633k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 11,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 21 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 21 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7307-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-BEGAPH?",
        "a": "7307 BEGAPH measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 41.5 kN, C0 26.5 kN, Pu 1.14 kN, reference speed 11,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "Which grease and fill for 7307-BEGAPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 11,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7307-BEGAPH?",
        "a": "The 11,000 r/min reference (thermal) and 11,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7307 BEP is the basic 35×80×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-BEGAPH",
      "7307 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7307 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 26.5,
    "fatigue_load_limit_kN": 1.14,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 BECBM is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 41.5 kN, C0 26.5 kN, Pu 1.14 kN.reference speed 11,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 450 g. Envelope economics: the 21 mm width over a 22.5 mm section yields 0.93 mm of ring width per section millimetre, and the bearing weighs 450 g for 41.5 kN of dynamic capacity — about 11 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 14,000 r/min while thermal balance under catalogue load sets the 11,000 r/min reference; at dm ≈ 57.5 mm the corresponding dn is approximately 805k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.79. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "One 7307-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7307-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-BECBM?",
        "a": "7307 BECBM measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 41.5 kN, C0 26.5 kN, Pu 1.14 kN, reference speed 11,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7307-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 35 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7307-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 14,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; 7307 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (41.5/26.5 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7307 BEP is the basic 35×80×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-BECBM",
      "7307 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7307-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7307 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 46.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7307 ACCBM is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 35×80×21 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 46.5 kN, C0 30 kN, Pu 1.27 kN.reference speed 11,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical), catalogue mass 450 g. Selection figures for 7307 ACCBM: the static-to-dynamic ratio C0/C is 0.65, Pu 1.27 kN is about 3 % of C, and catalogue mass works out to roughly 13 g per millimetre of bore. At the printed limiting speed of 17,000 r/min the mean pitch diameter dm ≈ 57.5 mm implies a dn value around 978k mm·r/min; the 11,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 21 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 35 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7307-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The 25° AC angle of 7307-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7307-ACCBM?",
        "a": "7307 ACCBM measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 450 g. SKF 17000 ratings: C 46.5 kN, C0 30 kN, Pu 1.27 kN, reference speed 11,000 r/min (thermal) and limiting speed 17,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7307-ACCBM?",
        "a": "With a rotating inner ring use roughly k5 on the 35 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7307-ACCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 17,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (46.5/30 kN vs 64/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7307 BEP shares the 35×80×21 mm angular-contact envelope, but catalogue C/C0 differ (46.5/30 kN vs 39/24.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7307-ACCBM",
      "7307 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7208 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 34.5,
    "static_load_kN": 24,
    "fatigue_load_limit_kN": 1.02,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 BE-2RZP is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 40×80×18 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 34.5 kN, C0 24 kN, Pu 1.02 kN.reference speed 10,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 420 g. Sizing arithmetic on the 40 mm bore: 34.5 kN C divided by the 20.0 mm radial section height gives 1.7 kN per section millimetre; the 420 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 1.02 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 34.5/24 kN ratings and 420 g mass this execution carries about 0.86 kN of C per millimetre of bore. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 18 mm width gives a bore/width ratio of 2.22; use these ratios when housing space around the 40 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7208-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7208-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-BE-2RZP?",
        "a": "7208 BE-2RZP measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 420 g. SKF 17000 ratings: C 34.5 kN, C0 24 kN, Pu 1.02 kN, reference speed 10,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Which grease and fill for 7208-BE-2RZP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 8,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7208-BE-2RZP?",
        "a": "The 10,000 r/min reference (thermal) and 8,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (34.5/24 kN vs 39/28 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (34.5/24 kN vs 41.5/29 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (34.5/24 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7208 BEP is the basic 40×80×18 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-BE-2RZP",
      "7208 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7208 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 34.5,
    "static_load_kN": 24,
    "fatigue_load_limit_kN": 1.02,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 BEP is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 40×80×18 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 34.5 kN, C0 24 kN, Pu 1.02 kN.reference speed 10,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), which coincide for this size, catalogue mass 370 g. Sizing arithmetic on the 40 mm bore: 34.5 kN C divided by the 20.0 mm radial section height gives 1.7 kN per section millimetre; the 370 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 1.02 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 34.5/24 kN ratings and 370 g mass this execution carries about 0.86 kN of C per millimetre of bore. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 18 mm width gives a bore/width ratio of 2.22; use these ratios when housing space around the 40 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7208-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7208-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7208 BEP as the single basic pa66 execution; the other order numbers of the 7208 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-BEP?",
        "a": "7208 BEP measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 370 g. SKF 17000 ratings: C 34.5 kN, C0 24 kN, Pu 1.02 kN, reference speed 10,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7208-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 10,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7208-BEP?",
        "a": "The 10,000 r/min reference (thermal) and 10,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (34.5/24 kN vs 39/28 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (34.5/24 kN vs 41.5/29 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (34.5/24 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7208 BEP is the basic 40×80×18 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-BEP",
      "7208 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7208 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 36.5,
    "static_load_kN": 26,
    "fatigue_load_limit_kN": 1.1,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 BECBP is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 40×80×18 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 36.5 kN, C0 26 kN, Pu 1.1 kN.reference speed 10,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 370 g. Load balance: C0 26 kN against C 36.5 kN gives a 0.71 ratio, typical of a steep-angle axial-oriented design; Pu 1.1 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 40 mm bore: 36.5 kN C divided by the 20.0 mm radial section height gives 1.8 kN per section millimetre; the 370 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 18 mm width gives a bore/width ratio of 2.22; use these ratios when housing space around the 40 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7208-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-BECBP?",
        "a": "7208 BECBP measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 370 g. SKF 17000 ratings: C 36.5 kN, C0 26 kN, Pu 1.1 kN, reference speed 10,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7208-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (36.5/26 kN vs 41.5/29 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (36.5/26 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7208 BEP is the basic 40×80×18 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-BECBP",
      "7208 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7208 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 36.5,
    "static_load_kN": 26,
    "fatigue_load_limit_kN": 1.1,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 BECBPH is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 40×80×18 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 36.5 kN, C0 26 kN, Pu 1.1 kN.reference speed 10,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 370 g. Sizing arithmetic on the 40 mm bore: 36.5 kN C divided by the 20.0 mm radial section height gives 1.8 kN per section millimetre; the 370 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 18 mm width over a 20.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 370 g for 36.5 kN of dynamic capacity — about 10 g per rated kN. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 18 mm width gives a bore/width ratio of 2.22; use these ratios when housing space around the 40 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 40 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 40 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7208-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-BECBPH?",
        "a": "7208 BECBPH measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 370 g. SKF 17000 ratings: C 36.5 kN, C0 26 kN, Pu 1.1 kN, reference speed 10,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Can one 7208-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7208-BECBPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (36.5/26 kN vs 41.5/29 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (36.5/26 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7208 BEP is the basic 40×80×18 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-BECBPH",
      "7208 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7208 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 36.5,
    "static_load_kN": 26,
    "fatigue_load_limit_kN": 1.1,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 BECBM is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 40×80×18 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 36.5 kN, C0 26 kN, Pu 1.1 kN.reference speed 10,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 370 g. At the printed limiting speed of 13,000 r/min the mean pitch diameter dm ≈ 60.0 mm implies a dn value around 780k mm·r/min; the 10,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 18 mm width over a 20.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 370 g for 36.5 kN of dynamic capacity — about 10 g per rated kN. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 18 mm width gives a bore/width ratio of 2.22; use these ratios when housing space around the 40 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 40 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7208-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-BECBM?",
        "a": "7208 BECBM measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 370 g. SKF 17000 ratings: C 36.5 kN, C0 26 kN, Pu 1.1 kN, reference speed 10,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7208-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (36.5/26 kN vs 41.5/29 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (36.5/26 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7208 BEP is the basic 40×80×18 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-BECBM",
      "7208 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7208 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 39,
    "static_load_kN": 28,
    "fatigue_load_limit_kN": 1.2,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 BECBY is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 40×80×18 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 39 kN, C0 28 kN, Pu 1.2 kN.reference speed 10,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 370 g. The 1.2 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 39/28 kN ratings and 370 g mass this execution carries about 0.97 kN of C per millimetre of bore. Sizing arithmetic on the 40 mm bore: 39 kN C divided by the 20.0 mm radial section height gives 1.9 kN per section millimetre; the 370 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 18 mm width gives a bore/width ratio of 2.22; use these ratios when housing space around the 40 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7208-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7208-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7208-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-BECBY?",
        "a": "7208 BECBY measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 370 g. SKF 17000 ratings: C 39 kN, C0 28 kN, Pu 1.2 kN, reference speed 10,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7208-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 11,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7208-BECBY?",
        "a": "The 10,000 r/min reference (thermal) and 11,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (39/28 kN vs 34.5/24 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (39/28 kN vs 34.5/24 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (39/28 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7208 BEP shares the 40×80×18 mm angular-contact envelope, but catalogue C/C0 differ (39/28 kN vs 34.5/24 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-BECBY",
      "7208 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7208-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7208 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 29,
    "fatigue_load_limit_kN": 1.25,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 370,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7208 ACCBM is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 40×80×18 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 41.5 kN, C0 29 kN, Pu 1.25 kN.reference speed 11,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical), catalogue mass 370 g. At the printed limiting speed of 16,000 r/min the mean pitch diameter dm ≈ 60.0 mm implies a dn value around 960k mm·r/min; the 11,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 18 mm width over a 20.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 370 g for 41.5 kN of dynamic capacity — about 9 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 16,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.69. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 40 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 18 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The 25° AC angle of 7208-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7208-ACCBM?",
        "a": "7208 ACCBM measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 370 g. SKF 17000 ratings: C 41.5 kN, C0 29 kN, Pu 1.25 kN, reference speed 11,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7208-ACCBM?",
        "a": "The 11,000 r/min reference (thermal) and 16,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7208-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (41.5/29 kN vs 34.5/24 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (41.5/29 kN vs 34.5/24 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (41.5/29 kN vs 36.5/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (41.5/29 kN vs 36.5/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (41.5/29 kN vs 36.5/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×18 mm envelope with catalogue ratings within 10 %; 7208 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-208-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (41.5/29 kN vs 56/49 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7208 BEP shares the 40×80×18 mm angular-contact envelope, but catalogue C/C0 differ (41.5/29 kN vs 34.5/24 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7208-ACCBM",
      "7208 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7308 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 46.2,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 1.29,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 BE-2RZP is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 40×90×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 46.2 kN, C0 30.5 kN, Pu 1.29 kN.reference speed 9,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 620 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 9,500 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 488k mm·r/min. Sizing arithmetic on the 40 mm bore: 46.2 kN C divided by the 25.0 mm radial section height gives 1.8 kN per section millimetre; the 620 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7308-BE-2RZP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "At 40 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7308-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 23 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7308-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7308-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-BE-2RZP?",
        "a": "7308 BE-2RZP measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 620 g. SKF 17000 ratings: C 46.2 kN, C0 30.5 kN, Pu 1.29 kN, reference speed 9,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Which fits should I use for 7308-BE-2RZP?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7308-BE-2RZP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 7,500 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 53/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7308 BEP is the basic 40×90×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-BE-2RZP",
      "7308 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7308 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 46.2,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 1.29,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 BEP is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 40×90×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 46.2 kN, C0 30.5 kN, Pu 1.29 kN.reference speed 9,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 620 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min while thermal balance under catalogue load sets the 9,500 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 585k mm·r/min. Sizing arithmetic on the 40 mm bore: 46.2 kN C divided by the 25.0 mm radial section height gives 1.8 kN per section millimetre; the 620 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 40 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 40 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7308-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7308 BEP as the single basic pa66 execution; the other order numbers of the 7308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-BEP?",
        "a": "7308 BEP measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 620 g. SKF 17000 ratings: C 46.2 kN, C0 30.5 kN, Pu 1.29 kN, reference speed 9,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which fits should I use for 7308-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7308-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 9,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 53/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (46.2/30.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7308 BEP is the basic 40×90×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-BEP",
      "7308 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7308 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 50,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.37,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 BECBP is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 40×90×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 50 kN, C0 32.5 kN, Pu 1.37 kN.reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 620 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 650k mm·r/min; the 9,500 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 23 mm width over a 25.0 mm section yields 0.92 mm of ring width per section millimetre, and the bearing weighs 620 g for 50 kN of dynamic capacity — about 12 g per rated kN. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7308-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7308-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7308-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-BECBP?",
        "a": "7308 BECBP measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 620 g. SKF 17000 ratings: C 50 kN, C0 32.5 kN, Pu 1.37 kN, reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7308-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7308 BEP is the basic 40×90×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-BECBP",
      "7308 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7308 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 50,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.37,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 BEGAPH is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 40×90×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 50 kN, C0 32.5 kN, Pu 1.37 kN.reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 620 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 650k mm·r/min; the 9,500 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 10,000 r/min while thermal balance under catalogue load sets the 9,500 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 650k mm·r/min. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7308-BEGAPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7308-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-BEGAPH?",
        "a": "7308 BEGAPH measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 620 g. SKF 17000 ratings: C 50 kN, C0 32.5 kN, Pu 1.37 kN, reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What minimum axial load does 7308-BEGAPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7308 BEP is the basic 40×90×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-BEGAPH",
      "7308 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7308 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 50,
    "static_load_kN": 32.5,
    "fatigue_load_limit_kN": 1.37,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 BECBM is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 40×90×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 50 kN, C0 32.5 kN, Pu 1.37 kN.reference speed 9,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 680 g. Load balance: C0 32.5 kN against C 50 kN gives a 0.65 ratio, typical of a steep-angle axial-oriented design; Pu 1.37 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 40 mm bore: 50 kN C divided by the 25.0 mm radial section height gives 2.0 kN per section millimetre; the 680 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "One 7308-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Assign interference to the rotating ring — roughly k5 on a 40 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7308-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-BECBM?",
        "a": "7308 BECBM measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 680 g. SKF 17000 ratings: C 50 kN, C0 32.5 kN, Pu 1.37 kN, reference speed 9,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7308-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 12,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7308-BECBM?",
        "a": "The 9,500 r/min reference (thermal) and 12,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (50/32.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7308 BEP is the basic 40×90×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-BECBM",
      "7308 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7308 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 53,
    "static_load_kN": 35.5,
    "fatigue_load_limit_kN": 1.5,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 640,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 BECBY is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 40×90×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 53 kN, C0 35.5 kN, Pu 1.5 kN.reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 640 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 650k mm·r/min; the 9,500 r/min reference speed is the thermal-planning figure under catalogue load. The 1.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 53/35.5 kN ratings and 640 g mass this execution carries about 1.32 kN of C per millimetre of bore. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 40 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7308-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-BECBY?",
        "a": "7308 BECBY measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 640 g. SKF 17000 ratings: C 53 kN, C0 35.5 kN, Pu 1.5 kN, reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which fits should I use for 7308-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7308-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 10,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (53/35.5 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (53/35.5 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (53/35.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (53/35.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (53/35.5 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7308 BEP shares the 40×90×23 mm angular-contact envelope, but catalogue C/C0 differ (53/35.5 kN vs 46.2/30.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-BECBY",
      "7308 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7308-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7308 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 56,
    "static_load_kN": 36,
    "fatigue_load_limit_kN": 1.53,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 680,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7308 ACCBM is SKF's 40 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 40×90×23 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 56 kN, C0 36 kN, Pu 1.53 kN.reference speed 10,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 680 g. Mass and section check: 680 g inside the 40×90×23 mm outline leaves a 25.0 mm radial section, and the 36 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 1.53 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 56/36 kN ratings and 680 g mass this execution carries about 1.40 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 10,000 r/min against a 15,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.67. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7308-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "One 7308-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The 25° AC angle of 7308-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7308-ACCBM?",
        "a": "7308 ACCBM measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 680 g. SKF 17000 ratings: C 56 kN, C0 36 kN, Pu 1.53 kN, reference speed 10,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7308-ACCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 15,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7308-ACCBM?",
        "a": "The 10,000 r/min reference (thermal) and 15,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; 7308 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (56/36 kN vs 78/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7308 BEP shares the 40×90×23 mm angular-contact envelope, but catalogue C/C0 differ (56/36 kN vs 46.2/30.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7308-ACCBM",
      "7308 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7209 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 35.8,
    "static_load_kN": 26,
    "fatigue_load_limit_kN": 1.12,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7209 BE-2RZP is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 45×85×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 35.8 kN, C0 26 kN, Pu 1.12 kN.reference speed 9,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 520 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 9,500 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 488k mm·r/min. Sizing arithmetic on the 45 mm bore: 35.8 kN C divided by the 20.0 mm radial section height gives 1.8 kN per section millimetre; the 520 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 19 mm width gives a bore/width ratio of 2.37; use these ratios when housing space around the 45 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7209-BE-2RZP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7209-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7209-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7209-BE-2RZP?",
        "a": "7209 BE-2RZP measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 520 g. SKF 17000 ratings: C 35.8 kN, C0 26 kN, Pu 1.12 kN, reference speed 9,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7209-BE-2RZP?",
        "a": "The 9,500 r/min reference (thermal) and 7,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7209-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (35.8/26 kN vs 40/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (35.8/26 kN vs 44/32 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (35.8/26 kN vs 63/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7209 BECBP is the basic 45×85×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209-BE-2RZP",
      "7209 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7209 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 38,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7209 BECBP is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 45×85×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 38 kN, C0 28.5 kN, Pu 1.22 kN.reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 420 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 650k mm·r/min; the 9,500 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 19 mm width over a 20.0 mm section yields 0.95 mm of ring width per section millimetre, and the bearing weighs 420 g for 38 kN of dynamic capacity — about 11 g per rated kN. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 19 mm width gives a bore/width ratio of 2.37; use these ratios when housing space around the 45 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 45 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "One 7209-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7209-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7209-BECBP?",
        "a": "7209 BECBP measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 38 kN, C0 28.5 kN, Pu 1.22 kN, reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7209-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7209-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 10,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (38/28.5 kN vs 44/32 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (38/28.5 kN vs 63/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7209 BECBP is the basic 45×85×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209-BECBP",
      "7209 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7209 BEGAPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 38,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7209 BEGAPH is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 45×85×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 38 kN, C0 28.5 kN, Pu 1.22 kN.reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 420 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 650k mm·r/min; the 9,500 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 10,000 r/min while thermal balance under catalogue load sets the 9,500 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 650k mm·r/min. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 19 mm width gives a bore/width ratio of 2.37; use these ratios when housing space around the 45 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEGAPH unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7209-BEGAPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7209-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7209-BEGAPH?",
        "a": "7209 BEGAPH measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 38 kN, C0 28.5 kN, Pu 1.22 kN, reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7209-BEGAPH?",
        "a": "The 9,500 r/min reference (thermal) and 10,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7209-BEGAPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (38/28.5 kN vs 44/32 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (38/28.5 kN vs 63/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7209 BECBP is the basic 45×85×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209-BEGAPH",
      "7209 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7209 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 38,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7209 BECBM is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 45×85×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 38 kN, C0 28.5 kN, Pu 1.22 kN.reference speed 9,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 420 g. Load balance: C0 28.5 kN against C 38 kN gives a 0.75 ratio, typical of a steep-angle axial-oriented design; Pu 1.22 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 45 mm bore: 38 kN C divided by the 20.0 mm radial section height gives 1.9 kN per section millimetre; the 420 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 19 mm width gives a bore/width ratio of 2.37; use these ratios when housing space around the 45 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "At 45 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7209-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7209-BECBM?",
        "a": "7209 BECBM measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 38 kN, C0 28.5 kN, Pu 1.22 kN, reference speed 9,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7209-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (38/28.5 kN vs 44/32 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (38/28.5 kN vs 63/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7209 BECBP is the basic 45×85×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209-BECBM",
      "7209 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7209 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 40,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 1.29,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7209 BECBY is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 45×85×19 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 40 kN, C0 30.5 kN, Pu 1.29 kN.reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 420 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 650k mm·r/min; the 9,500 r/min reference speed is the thermal-planning figure under catalogue load. The 1.29 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 40/30.5 kN ratings and 420 g mass this execution carries about 0.89 kN of C per millimetre of bore. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 19 mm width gives a bore/width ratio of 2.37; use these ratios when housing space around the 45 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Fillet radii must clear the chamfer so the 19 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 45 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "One 7209-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7209-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7209-BECBY?",
        "a": "7209 BECBY measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 40 kN, C0 30.5 kN, Pu 1.29 kN, reference speed 9,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7209-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (40/30.5 kN vs 35.8/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (40/30.5 kN vs 63/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7209 BECBP is the basic 45×85×19 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209-BECBY",
      "7209 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7209-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7209 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 44,
    "static_load_kN": 32,
    "fatigue_load_limit_kN": 1.37,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7209 ACCBM is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 45×85×19 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 44 kN, C0 32 kN, Pu 1.37 kN.reference speed 10,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical), catalogue mass 420 g. Mass and section check: 420 g inside the 45×85×19 mm outline leaves a 20.0 mm radial section, and the 32 kN static rating is 0.73× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 1.37 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 44/32 kN ratings and 420 g mass this execution carries about 0.98 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 10,000 r/min against a 15,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.67. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 45 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The 25° AC angle of 7209-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7209-ACCBM?",
        "a": "7209 ACCBM measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 44 kN, C0 32 kN, Pu 1.37 kN, reference speed 10,000 r/min (thermal) and limiting speed 15,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7209-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7209-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (44/32 kN vs 35.8/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (44/32 kN vs 38/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (44/32 kN vs 38/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (44/32 kN vs 38/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×19 mm envelope with catalogue ratings within 10 %; 7209 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-209-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (44/32 kN vs 63/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7209 BECBP shares the 45×85×19 mm angular-contact envelope, but catalogue C/C0 differ (44/32 kN vs 38/28.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7209-ACCBM",
      "7209 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7309 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 55.9,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.6,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 BE-2RZP is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 55.9 kN, C0 37.5 kN, Pu 1.6 kN.reference speed 8,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 850 g. Sizing arithmetic on the 45 mm bore: 55.9 kN C divided by the 27.5 mm radial section height gives 2.0 kN per section millimetre; the 850 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 1.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 55.9/37.5 kN ratings and 850 g mass this execution carries about 1.24 kN of C per millimetre of bore. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7309-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7309-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-BE-2RZP?",
        "a": "7309 BE-2RZP measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 850 g. SKF 17000 ratings: C 55.9 kN, C0 37.5 kN, Pu 1.6 kN, reference speed 8,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "Can one 7309-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7309-BE-2RZP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7309 BEP is the basic 45×100×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-BE-2RZP",
      "7309 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7309 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 55.9,
    "static_load_kN": 37.5,
    "fatigue_load_limit_kN": 1.6,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 BEP is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 55.9 kN, C0 37.5 kN, Pu 1.6 kN.reference speed 8,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 820 g. Sizing arithmetic on the 45 mm bore: 55.9 kN C divided by the 27.5 mm radial section height gives 2.0 kN per section millimetre; the 820 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 1.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 55.9/37.5 kN ratings and 820 g mass this execution carries about 1.24 kN of C per millimetre of bore. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps",
      "industrial transmissions"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7309-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7309-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7309-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7309 BEP as the single basic pa66 execution; the other order numbers of the 7309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-BEP?",
        "a": "7309 BEP measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 820 g. SKF 17000 ratings: C 55.9 kN, C0 37.5 kN, Pu 1.6 kN, reference speed 8,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Can one 7309-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7309-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (55.9/37.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7309 BEP is the basic 45×100×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-BEP",
      "7309 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7309 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 61,
    "static_load_kN": 40.5,
    "fatigue_load_limit_kN": 1.73,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 BECBP is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 61 kN, C0 40.5 kN, Pu 1.73 kN.reference speed 8,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 820 g. Load balance: C0 40.5 kN against C 61 kN gives a 0.66 ratio, typical of a steep-angle axial-oriented design; Pu 1.73 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 45 mm bore: 61 kN C divided by the 27.5 mm radial section height gives 2.2 kN per section millimetre; the 820 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7309-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7309-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7309-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-BECBP?",
        "a": "7309 BECBP measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 820 g. SKF 17000 ratings: C 61 kN, C0 40.5 kN, Pu 1.73 kN, reference speed 8,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7309-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7309-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7309 BEP is the basic 45×100×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-BECBP",
      "7309 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7309 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 61,
    "static_load_kN": 40.5,
    "fatigue_load_limit_kN": 1.73,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 820,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 BEGAPH is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 61 kN, C0 40.5 kN, Pu 1.73 kN.reference speed 8,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 820 g. Sizing arithmetic on the 45 mm bore: 61 kN C divided by the 27.5 mm radial section height gives 2.2 kN per section millimetre; the 820 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 820 g for 61 kN of dynamic capacity — about 13 g per rated kN. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At 45 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7309-BEGAPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7309-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-BEGAPH?",
        "a": "7309 BEGAPH measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 820 g. SKF 17000 ratings: C 61 kN, C0 40.5 kN, Pu 1.73 kN, reference speed 8,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "Which grease and fill for 7309-BEGAPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 9,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7309-BEGAPH?",
        "a": "The 8,500 r/min reference (thermal) and 9,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7309 BEP is the basic 45×100×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-BEGAPH",
      "7309 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7309 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 61,
    "static_load_kN": 40.5,
    "fatigue_load_limit_kN": 1.73,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 BECBM is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 61 kN, C0 40.5 kN, Pu 1.73 kN.reference speed 8,500 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 910 g. At the printed limiting speed of 11,000 r/min the mean pitch diameter dm ≈ 72.5 mm implies a dn value around 798k mm·r/min; the 8,500 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 910 g for 61 kN of dynamic capacity — about 15 g per rated kN. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "One 7309-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 45 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7309-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-BECBM?",
        "a": "7309 BECBM measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 910 g. SKF 17000 ratings: C 61 kN, C0 40.5 kN, Pu 1.73 kN, reference speed 8,500 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7309-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7309-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 11,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (61/40.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7309 BEP is the basic 45×100×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-BECBM",
      "7309 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7309 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 64,
    "static_load_kN": 45,
    "fatigue_load_limit_kN": 1.9,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 870,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 BECBY is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 45×100×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 64 kN, C0 45 kN, Pu 1.9 kN.reference speed 8,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 870 g. The 1.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 64/45 kN ratings and 870 g mass this execution carries about 1.42 kN of C per millimetre of bore. Sizing arithmetic on the 45 mm bore: 64 kN C divided by the 27.5 mm radial section height gives 2.3 kN per section millimetre; the 870 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 45 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7309-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7309-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-BECBY?",
        "a": "7309 BECBY measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 870 g. SKF 17000 ratings: C 64 kN, C0 45 kN, Pu 1.9 kN, reference speed 8,500 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Can one 7309-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7309-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (64/45 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7309 BEP shares the 45×100×25 mm angular-contact envelope, but catalogue C/C0 differ (64/45 kN vs 55.9/37.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-BECBY",
      "7309 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7309-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7309 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 68,
    "static_load_kN": 45.5,
    "fatigue_load_limit_kN": 1.93,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7309 ACCBM is SKF's 45 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 45×100×25 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 68 kN, C0 45.5 kN, Pu 1.93 kN.reference speed 9,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 910 g. At the printed limiting speed of 13,000 r/min the mean pitch diameter dm ≈ 72.5 mm implies a dn value around 943k mm·r/min; the 9,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 910 g for 68 kN of dynamic capacity — about 13 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 9,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.69. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "One 7309-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The 25° AC angle of 7309-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7309-ACCBM?",
        "a": "7309 ACCBM measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 910 g. SKF 17000 ratings: C 68 kN, C0 45.5 kN, Pu 1.93 kN, reference speed 9,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7309-ACCBM?",
        "a": "The 9,000 r/min reference (thermal) and 13,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7309-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; 7309 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (68/45.5 kN vs 100/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7309 BEP shares the 45×100×25 mm angular-contact envelope, but catalogue C/C0 differ (68/45.5 kN vs 55.9/37.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7309-ACCBM",
      "7309 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7210 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 37.7,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 BE-2RZP is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 37.7 kN, C0 28.5 kN, Pu 1.22 kN.reference speed 9,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 550 g. Selection figures for 7210 BE-2RZP: the static-to-dynamic ratio C0/C is 0.76, Pu 1.22 kN is about 3 % of C, and catalogue mass works out to roughly 11 g per millimetre of bore. Load balance: C0 28.5 kN against C 37.7 kN gives a 0.76 ratio, typical of a steep-angle axial-oriented design; Pu 1.22 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7210-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7210-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-BE-2RZP?",
        "a": "7210 BE-2RZP measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 550 g. SKF 17000 ratings: C 37.7 kN, C0 28.5 kN, Pu 1.22 kN, reference speed 9,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7210-BE-2RZP?",
        "a": "The 9,000 r/min reference (thermal) and 7,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7210-BE-2RZP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (37.7/28.5 kN vs 41.5/33.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (37.7/28.5 kN vs 45.5/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (37.7/28.5 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7210 BEP is the basic 50×90×20 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-BE-2RZP",
      "7210 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7210 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 37.7,
    "static_load_kN": 28.5,
    "fatigue_load_limit_kN": 1.22,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 BEP is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 37.7 kN, C0 28.5 kN, Pu 1.22 kN.reference speed 9,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 470 g. Selection figures for 7210 BEP: the static-to-dynamic ratio C0/C is 0.76, Pu 1.22 kN is about 3 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Load balance: C0 28.5 kN against C 37.7 kN gives a 0.76 ratio, typical of a steep-angle axial-oriented design; Pu 1.22 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 50 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7210-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7210 BEP as the single basic pa66 execution; the other order numbers of the 7210 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-BEP?",
        "a": "7210 BEP measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 470 g. SKF 17000 ratings: C 37.7 kN, C0 28.5 kN, Pu 1.22 kN, reference speed 9,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7210-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (37.7/28.5 kN vs 41.5/33.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (37.7/28.5 kN vs 45.5/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (37.7/28.5 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7210 BEP is the basic 50×90×20 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-BEP",
      "7210 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7210 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 40,
    "static_load_kN": 31,
    "fatigue_load_limit_kN": 1.32,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 BECBP is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 40 kN, C0 31 kN, Pu 1.32 kN.reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size, catalogue mass 470 g. Envelope economics: the 20 mm width over a 20.0 mm section yields 1.00 mm of ring width per section millimetre, and the bearing weighs 470 g for 40 kN of dynamic capacity — about 12 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min while thermal balance under catalogue load sets the 9,000 r/min reference; at dm ≈ 70.0 mm the corresponding dn is approximately 630k mm·r/min. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7210-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7210-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-BECBP?",
        "a": "7210 BECBP measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 470 g. SKF 17000 ratings: C 40 kN, C0 31 kN, Pu 1.32 kN, reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7210-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 50 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7210-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 9,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (40/31 kN vs 45.5/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (40/31 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7210 BEP is the basic 50×90×20 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-BECBP",
      "7210 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7210 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 40,
    "static_load_kN": 31,
    "fatigue_load_limit_kN": 1.32,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 BECBPH is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 40 kN, C0 31 kN, Pu 1.32 kN.reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size, catalogue mass 470 g. Envelope economics: the 20 mm width over a 20.0 mm section yields 1.00 mm of ring width per section millimetre, and the bearing weighs 470 g for 40 kN of dynamic capacity — about 12 g per rated kN. Selection figures for 7210 BECBPH: the static-to-dynamic ratio C0/C is 0.78, Pu 1.32 kN is about 3 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7210-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-BECBPH?",
        "a": "7210 BECBPH measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 470 g. SKF 17000 ratings: C 40 kN, C0 31 kN, Pu 1.32 kN, reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Which fits should I use for 7210-BECBPH?",
        "a": "With a rotating inner ring use roughly k5 on the 50 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7210-BECBPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 9,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (40/31 kN vs 45.5/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (40/31 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7210 BEP is the basic 50×90×20 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-BECBPH",
      "7210 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7210 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 40,
    "static_load_kN": 31,
    "fatigue_load_limit_kN": 1.32,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 BECBM is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 40 kN, C0 31 kN, Pu 1.32 kN.reference speed 9,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 470 g. The 1.32 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 40/31 kN ratings and 470 g mass this execution carries about 0.80 kN of C per millimetre of bore. Load balance: C0 31 kN against C 40 kN gives a 0.78 ratio, typical of a steep-angle axial-oriented design; Pu 1.32 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7210-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7210-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-BECBM?",
        "a": "7210 BECBM measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 470 g. SKF 17000 ratings: C 40 kN, C0 31 kN, Pu 1.32 kN, reference speed 9,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7210-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 11,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7210-BECBM?",
        "a": "The 9,000 r/min reference (thermal) and 11,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (40/31 kN vs 45.5/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (40/31 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7210 BEP is the basic 50×90×20 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-BECBM",
      "7210 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7210 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 41.5,
    "static_load_kN": 33.5,
    "fatigue_load_limit_kN": 1.4,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 BECBY is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 50×90×20 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 41.5 kN, C0 33.5 kN, Pu 1.4 kN.reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size, catalogue mass 470 g. Envelope economics: the 20 mm width over a 20.0 mm section yields 1.00 mm of ring width per section millimetre, and the bearing weighs 470 g for 41.5 kN of dynamic capacity — about 11 g per rated kN. Mass and section check: 470 g inside the 50×90×20 mm outline leaves a 20.0 mm radial section, and the 33.5 kN static rating is 0.81× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 20 mm width gives a bore/width ratio of 2.50; use these ratios when housing space around the 50 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7210-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-BECBY?",
        "a": "7210 BECBY measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 470 g. SKF 17000 ratings: C 41.5 kN, C0 33.5 kN, Pu 1.4 kN, reference speed 9,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7210-BECBY?",
        "a": "The 9,000 r/min reference (thermal) and 9,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7210-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (41.5/33.5 kN vs 37.7/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (41.5/33.5 kN vs 37.7/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (41.5/33.5 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7210 BEP shares the 50×90×20 mm angular-contact envelope, but catalogue C/C0 differ (41.5/33.5 kN vs 37.7/28.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-BECBY",
      "7210 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7210-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7210 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 45.5,
    "static_load_kN": 35.5,
    "fatigue_load_limit_kN": 1.5,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 470,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7210 ACCBM is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 50×90×20 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 45.5 kN, C0 35.5 kN, Pu 1.5 kN.reference speed 9,500 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 470 g. The 1.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 45.5/35.5 kN ratings and 470 g mass this execution carries about 0.91 kN of C per millimetre of bore. Load balance: C0 35.5 kN against C 45.5 kN gives a 0.78 ratio, typical of a steep-angle axial-oriented design; Pu 1.5 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 9,500 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.68. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7210-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The 25° AC angle of 7210-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7210-ACCBM?",
        "a": "7210 ACCBM measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 470 g. SKF 17000 ratings: C 45.5 kN, C0 35.5 kN, Pu 1.5 kN, reference speed 9,500 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7210-ACCBM?",
        "a": "With a rotating inner ring use roughly k5 on the 50 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (45.5/35.5 kN vs 37.7/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (45.5/35.5 kN vs 37.7/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (45.5/35.5 kN vs 40/31 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (45.5/35.5 kN vs 40/31 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (45.5/35.5 kN vs 40/31 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×20 mm envelope with catalogue ratings within 10 %; 7210 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-210-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (45.5/35.5 kN vs 65.5/61 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7210 BEP shares the 50×90×20 mm angular-contact envelope, but catalogue C/C0 differ (45.5/35.5 kN vs 37.7/28.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7210-ACCBM",
      "7210 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7310 BE-2RZP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 68.9,
    "static_load_kN": 47.5,
    "fatigue_load_limit_kN": 2,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7310 BE-2RZP is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 50×110×27 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 68.9 kN, C0 47.5 kN, Pu 2 kN.reference speed 7,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 1200 g. Mass and section check: 1200 g inside the 50×110×27 mm outline leaves a 30.0 mm radial section, and the 47.5 kN static rating is 0.69× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 47.5 kN against C 68.9 kN gives a 0.69 ratio, typical of a steep-angle axial-oriented design; Pu 2 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 27 mm width gives a bore/width ratio of 1.85; use these ratios when housing space around the 50 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BE-2RZP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable BE-2RZP unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "One 7310-BE-2RZP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7310-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7310-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7310-BE-2RZP?",
        "a": "7310 BE-2RZP measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1200 g. SKF 17000 ratings: C 68.9 kN, C0 47.5 kN, Pu 2 kN, reference speed 7,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7310-BE-2RZP?",
        "a": "With a rotating inner ring use roughly k5 on the 50 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (68.9/47.5 kN vs 78/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (68.9/47.5 kN vs 83/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (68.9/47.5 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (68.9/47.5 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7310 BECBP is the basic 50×110×27 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310-BE-2RZP",
      "7310 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7310 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 75,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7310 BECBP is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 50×110×27 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 75 kN, C0 51 kN, Pu 2.16 kN.reference speed 7,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 1100 g. Sizing arithmetic on the 50 mm bore: 75 kN C divided by the 30.0 mm radial section height gives 2.5 kN per section millimetre; the 1100 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 1100 g inside the 50×110×27 mm outline leaves a 30.0 mm radial section, and the 51 kN static rating is 0.68× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 27 mm width gives a bore/width ratio of 1.85; use these ratios when housing space around the 50 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7310-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7310-BECBP?",
        "a": "7310 BECBP measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1100 g. SKF 17000 ratings: C 75 kN, C0 51 kN, Pu 2.16 kN, reference speed 7,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7310-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7310-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 83/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7310 BECBP is the basic 50×110×27 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310-BECBP",
      "7310 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7310 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 75,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7310 BEGAPH is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 50×110×27 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 75 kN, C0 51 kN, Pu 2.16 kN.reference speed 7,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 1100 g. Mass and section check: 1100 g inside the 50×110×27 mm outline leaves a 30.0 mm radial section, and the 51 kN static rating is 0.68× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 8,000 r/min the mean pitch diameter dm ≈ 80.0 mm implies a dn value around 640k mm·r/min; the 7,500 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 27 mm width gives a bore/width ratio of 1.85; use these ratios when housing space around the 50 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 50 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7310-BEGAPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7310-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7310-BEGAPH?",
        "a": "7310 BEGAPH measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1100 g. SKF 17000 ratings: C 75 kN, C0 51 kN, Pu 2.16 kN, reference speed 7,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7310-BEGAPH?",
        "a": "With a rotating inner ring use roughly k5 on the 50 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 83/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7310 BECBP is the basic 50×110×27 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310-BEGAPH",
      "7310 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7310 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 75,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7310 BECBM is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 50×110×27 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 75 kN, C0 51 kN, Pu 2.16 kN.reference speed 7,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 1100 g. Selection figures for 7310 BECBM: the static-to-dynamic ratio C0/C is 0.68, Pu 2.16 kN is about 3 % of C, and catalogue mass works out to roughly 22 g per millimetre of bore. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 80.0 mm implies a dn value around 800k mm·r/min; the 7,500 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 27 mm width gives a bore/width ratio of 1.85; use these ratios when housing space around the 50 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 50 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7310-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7310-BECBM?",
        "a": "7310 BECBM measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1100 g. SKF 17000 ratings: C 75 kN, C0 51 kN, Pu 2.16 kN, reference speed 7,500 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7310-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 83/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (75/51 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7310 BECBP is the basic 50×110×27 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310-BECBM",
      "7310 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7310 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 78,
    "static_load_kN": 56,
    "fatigue_load_limit_kN": 2.36,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7310 BECBY is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 50×110×27 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 78 kN, C0 56 kN, Pu 2.36 kN.reference speed 7,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 1150 g. Load balance: C0 56 kN against C 78 kN gives a 0.72 ratio, typical of a steep-angle axial-oriented design; Pu 2.36 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 1150 g inside the 50×110×27 mm outline leaves a 30.0 mm radial section, and the 56 kN static rating is 0.72× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 27 mm width gives a bore/width ratio of 1.85; use these ratios when housing space around the 50 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "At 50 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7310-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7310-BECBY?",
        "a": "7310 BECBY measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1150 g. SKF 17000 ratings: C 78 kN, C0 56 kN, Pu 2.36 kN, reference speed 7,500 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Can one 7310-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7310-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (78/56 kN vs 68.9/47.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (78/56 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (78/56 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7310 BECBP is the basic 50×110×27 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310-BECBY",
      "7310 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7310-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7310 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 83,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.4,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7310 ACCBM is SKF's 50 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 50×110×27 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 83 kN, C0 57 kN, Pu 2.4 kN.reference speed 8,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 1100 g. Envelope economics: the 27 mm width over a 30.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 1100 g for 83 kN of dynamic capacity — about 13 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 12,000 r/min while thermal balance under catalogue load sets the 8,000 r/min reference; at dm ≈ 80.0 mm the corresponding dn is approximately 960k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 12,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.67. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "At 50 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The 25° AC angle of 7310-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7310-ACCBM?",
        "a": "7310 ACCBM measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1100 g. SKF 17000 ratings: C 83 kN, C0 57 kN, Pu 2.4 kN, reference speed 8,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7310-ACCBM?",
        "a": "The 8,000 r/min reference (thermal) and 12,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7310-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (83/57 kN vs 68.9/47.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (83/57 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (83/57 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (83/57 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; 7310 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (83/57 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (83/57 kN vs 118/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7310 BECBP shares the 50×110×27 mm angular-contact envelope, but catalogue C/C0 differ (83/57 kN vs 75/51 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7310-ACCBM",
      "7310 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-BE-2RZP",
    "brand": "SKF",
    "manufacturer_designation": "7211 BE-2RZP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "RSR",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 46.2,
    "static_load_kN": 36,
    "fatigue_load_limit_kN": 1.53,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 BE-2RZP is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 55×100×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 46.2 kN, C0 36 kN, Pu 1.53 kN.reference speed 8,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 620 g. Load balance: C0 36 kN against C 46.2 kN gives a 0.78 ratio, typical of a steep-angle axial-oriented design; Pu 1.53 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 620 g inside the 55×100×21 mm outline leaves a 22.5 mm radial section, and the 36 kN static rating is 0.78× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. Sealing note: the two non-contact NBR -2RZ seals run in recessed grooves without touching the inner ring, so drag and speed loss stay small while the standard grease fill is retained and coarse dust is excluded; they are not lip-contact seals, so pressure washing and fine slurry still require external housing seals. The uncapped BECBP/BEP executions are the open counterparts.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "grease ageing inside the non-contact-sealed cavity after long service with no relubrication access",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7211-BE-2RZP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "The non-contact -2RZ seals of 7211-BE-2RZP add little drag but are not contact seals; in wet or fine-dust duty retain external sealing at the housing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-BE-2RZP?",
        "a": "7211 BE-2RZP measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 46.2 kN, C0 36 kN, Pu 1.53 kN, reference speed 8,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BE-2RZP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. -2RZ marks non-contact NBR seals on both sides riding in recessed grooves: they keep contamination and the standard grease fill in without lip drag, and P again denotes the PA66 cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7211-BE-2RZP?",
        "a": "With a rotating inner ring use roughly k5 on the 55 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; seal variant (RSR vs OPEN) and load ratings differ — confirm sealing and rating before substituting."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 51/42.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7211 BEP is the basic 55×100×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-BE-2RZP",
      "7211 BE-2RZP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7211 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 46.2,
    "static_load_kN": 36,
    "fatigue_load_limit_kN": 1.53,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 BEP is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 55×100×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 46.2 kN, C0 36 kN, Pu 1.53 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 620 g. Load balance: C0 36 kN against C 46.2 kN gives a 0.78 ratio, typical of a steep-angle axial-oriented design; Pu 1.53 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 620 g inside the 55×100×21 mm outline leaves a 22.5 mm radial section, and the 36 kN static rating is 0.78× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7211-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7211-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7211 BEP as the single basic pa66 execution; the other order numbers of the 7211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-BEP?",
        "a": "7211 BEP measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 46.2 kN, C0 36 kN, Pu 1.53 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Can one 7211-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7211-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BE-2RZP is the glass-fibre PA66 cage, non-contact NBR seals (-2RZ) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 51/42.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (46.2/36 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7211 BEP is the basic 55×100×21 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-BEP",
      "7211 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7211 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 49,
    "static_load_kN": 40,
    "fatigue_load_limit_kN": 1.66,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 BECBP is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 55×100×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 49 kN, C0 40 kN, Pu 1.66 kN.reference speed 8,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), which coincide for this size, catalogue mass 620 g. The 1.66 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 49/40 kN ratings and 620 g mass this execution carries about 0.89 kN of C per millimetre of bore. Load balance: C0 40 kN against C 49 kN gives a 0.82 ratio, typical of a steep-angle axial-oriented design; Pu 1.66 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly k5 on a 55 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7211-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-BECBP?",
        "a": "7211 BECBP measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 49 kN, C0 40 kN, Pu 1.66 kN, reference speed 8,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7211-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 8,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7211-BECBP?",
        "a": "The 8,000 r/min reference (thermal) and 8,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (49/40 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-BECBP",
      "7211 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7211 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 49,
    "static_load_kN": 40,
    "fatigue_load_limit_kN": 1.66,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 BECBPH is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 55×100×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 49 kN, C0 40 kN, Pu 1.66 kN.reference speed 8,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), which coincide for this size, catalogue mass 620 g. Load balance: C0 40 kN against C 49 kN gives a 0.82 ratio, typical of a steep-angle axial-oriented design; Pu 1.66 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 8,000 r/min while thermal balance under catalogue load sets the 8,000 r/min reference; at dm ≈ 77.5 mm the corresponding dn is approximately 620k mm·r/min. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 55 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7211-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Fillet radii must clear the chamfer so the 21 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7211-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-BECBPH?",
        "a": "7211 BECBPH measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 49 kN, C0 40 kN, Pu 1.66 kN, reference speed 8,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7211-BECBPH?",
        "a": "With a rotating inner ring use roughly k5 on the 55 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (49/40 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-BECBPH",
      "7211 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7211 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 49,
    "static_load_kN": 40,
    "fatigue_load_limit_kN": 1.66,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 BECBM is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 55×100×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 49 kN, C0 40 kN, Pu 1.66 kN.reference speed 8,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 620 g. Envelope economics: the 21 mm width over a 22.5 mm section yields 0.93 mm of ring width per section millimetre, and the bearing weighs 620 g for 49 kN of dynamic capacity — about 13 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 10,000 r/min while thermal balance under catalogue load sets the 8,000 r/min reference; at dm ≈ 77.5 mm the corresponding dn is approximately 775k mm·r/min. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "One 7211-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7211-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7211-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7211-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-BECBM?",
        "a": "7211 BECBM measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 49 kN, C0 40 kN, Pu 1.66 kN, reference speed 8,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7211-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (49/40 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (49/40 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-BECBM",
      "7211 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7211 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 51,
    "static_load_kN": 42.5,
    "fatigue_load_limit_kN": 1.8,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 BECBY is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 55×100×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 51 kN, C0 42.5 kN, Pu 1.8 kN.reference speed 8,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), which coincide for this size, catalogue mass 620 g. Mass and section check: 620 g inside the 55×100×21 mm outline leaves a 22.5 mm radial section, and the 42.5 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 42.5 kN against C 51 kN gives a 0.83 ratio, typical of a steep-angle axial-oriented design; Pu 1.8 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7211-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7211-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-BECBY?",
        "a": "7211 BECBY measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 51 kN, C0 42.5 kN, Pu 1.8 kN, reference speed 8,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7211-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 8,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7211-BECBY?",
        "a": "The 8,000 r/min reference (thermal) and 8,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (51/42.5 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (51/42.5 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; 7211 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (51/42.5 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (51/42.5 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (51/42.5 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (51/42.5 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-BECBY",
      "7211 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7211-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7211 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 57,
    "static_load_kN": 45,
    "fatigue_load_limit_kN": 1.9,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 620,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7211 ACCBM is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 55×100×21 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 57 kN, C0 45 kN, Pu 1.9 kN.reference speed 8,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 620 g. Selection figures for 7211 ACCBM: the static-to-dynamic ratio C0/C is 0.79, Pu 1.9 kN is about 3 % of C, and catalogue mass works out to roughly 11 g per millimetre of bore. At the printed limiting speed of 12,000 r/min the mean pitch diameter dm ≈ 77.5 mm implies a dn value around 930k mm·r/min; the 8,500 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 8,500 r/min against a 12,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.71. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills",
      "test-rig and balancing-machine shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 21 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 55 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The 25° AC angle of 7211-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7211-ACCBM?",
        "a": "7211 ACCBM measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 620 g. SKF 17000 ratings: C 57 kN, C0 45 kN, Pu 1.9 kN, reference speed 8,500 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7211-ACCBM?",
        "a": "With a rotating inner ring use roughly k5 on the 55 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7211-ACCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 12,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 51/42.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (57/45 kN vs 85/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (57/45 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7211-ACCBM",
      "7211 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7311 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 79.3,
    "static_load_kN": 55,
    "fatigue_load_limit_kN": 2.32,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 BEP is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 55×120×29 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 79.3 kN, C0 55 kN, Pu 2.32 kN.reference speed 7,000 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1400 g. Envelope economics: the 29 mm width over a 32.5 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 1400 g for 79.3 kN of dynamic capacity — about 18 g per rated kN. Mass and section check: 1400 g inside the 55×120×29 mm outline leaves a 32.5 mm radial section, and the 55 kN static rating is 0.69× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 29 mm width gives a bore/width ratio of 1.90; use these ratios when housing space around the 55 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 55 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring — roughly k5 on a 55 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 29 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7311-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7311 BEP as the single basic pa66 execution; the other order numbers of the 7311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7311-BEP?",
        "a": "7311 BEP measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1400 g. SKF 17000 ratings: C 79.3 kN, C0 55 kN, Pu 2.32 kN, reference speed 7,000 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7311-BEP?",
        "a": "The 7,000 r/min reference (thermal) and 6,700 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7311-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (79.3/55 kN vs 90/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (79.3/55 kN vs 96.5/67 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (79.3/55 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (79.3/55 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7311 BEP is the basic 55×120×29 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311-BEP",
      "7311 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7311 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 85,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 BECBP is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 55×120×29 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 85 kN, C0 60 kN, Pu 2.55 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size, catalogue mass 1400 g. Selection figures for 7311 BECBP: the static-to-dynamic ratio C0/C is 0.71, Pu 2.55 kN is about 3 % of C, and catalogue mass works out to roughly 25 g per millimetre of bore. At the printed limiting speed of 7,000 r/min the mean pitch diameter dm ≈ 87.5 mm implies a dn value around 613k mm·r/min; the 7,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 29 mm width gives a bore/width ratio of 1.90; use these ratios when housing space around the 55 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps",
      "centrifugal and vacuum pumps"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 29 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "One 7311-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7311-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7311-BECBP?",
        "a": "7311 BECBP measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1400 g. SKF 17000 ratings: C 85 kN, C0 60 kN, Pu 2.55 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7311-BECBP?",
        "a": "The 7,000 r/min reference (thermal) and 7,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7311-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 96.5/67 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7311 BEP is the basic 55×120×29 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311-BECBP",
      "7311 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7311 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 85,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 BECBPH is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 55×120×29 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 85 kN, C0 60 kN, Pu 2.55 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size, catalogue mass 1400 g. Selection figures for 7311 BECBPH: the static-to-dynamic ratio C0/C is 0.71, Pu 2.55 kN is about 3 % of C, and catalogue mass works out to roughly 25 g per millimetre of bore. Envelope economics: the 29 mm width over a 32.5 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 1400 g for 85 kN of dynamic capacity — about 16 g per rated kN. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 29 mm width gives a bore/width ratio of 1.90; use these ratios when housing space around the 55 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "test-rig and balancing-machine shafts",
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "At 55 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7311-BECBPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7311-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7311-BECBPH?",
        "a": "7311 BECBPH measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1400 g. SKF 17000 ratings: C 85 kN, C0 60 kN, Pu 2.55 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7311-BECBPH?",
        "a": "The 7,000 r/min reference (thermal) and 7,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7311-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 96.5/67 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7311 BEP is the basic 55×120×29 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311-BECBPH",
      "7311 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7311 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 85,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 BECBM is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 55×120×29 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 85 kN, C0 60 kN, Pu 2.55 kN.reference speed 7,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 1400 g. Sizing arithmetic on the 55 mm bore: 85 kN C divided by the 32.5 mm radial section height gives 2.6 kN per section millimetre; the 1400 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 1400 g inside the 55×120×29 mm outline leaves a 32.5 mm radial section, and the 60 kN static rating is 0.71× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 29 mm width gives a bore/width ratio of 1.90; use these ratios when housing space around the 55 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "machine-tool spindles and spindle units",
      "servo drives and precision gearboxes",
      "gear pumps and screw-type pumps"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "One 7311-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7311-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7311-BECBM?",
        "a": "7311 BECBM measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1400 g. SKF 17000 ratings: C 85 kN, C0 60 kN, Pu 2.55 kN, reference speed 7,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7311-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7311-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 96.5/67 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (85/60 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7311 BEP is the basic 55×120×29 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311-BECBM",
      "7311 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7311 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 90,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 BECBY is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 55×120×29 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 90 kN, C0 65.5 kN, Pu 2.75 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size, catalogue mass 1400 g. Selection figures for 7311 BECBY: the static-to-dynamic ratio C0/C is 0.73, Pu 2.75 kN is about 3 % of C, and catalogue mass works out to roughly 25 g per millimetre of bore. Load balance: C0 65.5 kN against C 90 kN gives a 0.73 ratio, typical of a steep-angle axial-oriented design; Pu 2.75 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 29 mm width gives a bore/width ratio of 1.90; use these ratios when housing space around the 55 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "centrifugal and vacuum pumps",
      "industrial transmissions",
      "printing cylinders and packaging shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 29 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7311-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7311-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7311-BECBY?",
        "a": "7311 BECBY measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1400 g. SKF 17000 ratings: C 90 kN, C0 65.5 kN, Pu 2.75 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7311-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (90/65.5 kN vs 79.3/55 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 ACCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (90/65.5 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (90/65.5 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7311 BEP shares the 55×120×29 mm angular-contact envelope, but catalogue C/C0 differ (90/65.5 kN vs 79.3/55 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311-BECBY",
      "7311 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7311-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7311 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 96.5,
    "static_load_kN": 67,
    "fatigue_load_limit_kN": 2.85,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 1400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7311 ACCBM is SKF's 55 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 55×120×29 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 96.5 kN, C0 67 kN, Pu 2.85 kN.reference speed 7,500 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 1400 g. Sizing arithmetic on the 55 mm bore: 96.5 kN C divided by the 32.5 mm radial section height gives 3.0 kN per section millimetre; the 1400 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 1400 g inside the 55×120×29 mm outline leaves a 32.5 mm radial section, and the 67 kN static rating is 0.69× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 7,500 r/min against a 11,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.68. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "industrial transmissions",
      "printing cylinders and packaging shafts",
      "belt-driven internal-grinding quills"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7311-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 55 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The 25° AC angle of 7311-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7311-ACCBM?",
        "a": "7311 ACCBM measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1400 g. SKF 17000 ratings: C 96.5 kN, C0 67 kN, Pu 2.85 kN, reference speed 7,500 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7311-ACCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 11,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7311-ACCBM?",
        "a": "The 7,500 r/min reference (thermal) and 11,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (96.5/67 kN vs 79.3/55 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (96.5/67 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (96.5/67 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (96.5/67 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; 7311 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (96.5/67 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (96.5/67 kN vs 137/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7311 BEP shares the 55×120×29 mm angular-contact envelope, but catalogue C/C0 differ (96.5/67 kN vs 79.3/55 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7311-ACCBM",
      "7311 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7212 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 57.2,
    "static_load_kN": 45.5,
    "fatigue_load_limit_kN": 1.93,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 BEP is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 57.2 kN, C0 45.5 kN, Pu 1.93 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size, catalogue mass 800 g. At the printed limiting speed of 7,000 r/min the mean pitch diameter dm ≈ 85.0 mm implies a dn value around 595k mm·r/min; the 7,000 r/min reference speed is the thermal-planning figure under catalogue load. The 1.93 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 57.2/45.5 kN ratings and 800 g mass this execution carries about 0.95 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7212-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7212-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7212 BEP as the single basic pa66 execution; the other order numbers of the 7212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7212-BEP?",
        "a": "7212 BEP measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 800 g. SKF 17000 ratings: C 57.2 kN, C0 45.5 kN, Pu 1.93 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7212-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (57.2/45.5 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (57.2/45.5 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (57.2/45.5 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (57.2/45.5 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7212 BEP is the basic 60×110×22 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212-BEP",
      "7212 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7212 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 61,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 BECBP is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 61 kN, C0 50 kN, Pu 2.12 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 7,000 r/min reference; at dm ≈ 85.0 mm the corresponding dn is approximately 638k mm·r/min. Selection figures for 7212 BECBP: the static-to-dynamic ratio C0/C is 0.82, Pu 2.12 kN is about 3 % of C, and catalogue mass works out to roughly 13 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 7,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "At 60 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7212-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7212-BECBP?",
        "a": "7212 BECBP measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 800 g. SKF 17000 ratings: C 61 kN, C0 50 kN, Pu 2.12 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7212-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7212-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 7,500 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7212 BEP is the basic 60×110×22 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212-BECBP",
      "7212 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7212 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 61,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 BECBPH is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 61 kN, C0 50 kN, Pu 2.12 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 7,000 r/min reference; at dm ≈ 85.0 mm the corresponding dn is approximately 638k mm·r/min. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 85.0 mm implies a dn value around 638k mm·r/min; the 7,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 7,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 22 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7212-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7212-BECBPH?",
        "a": "7212 BECBPH measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 800 g. SKF 17000 ratings: C 61 kN, C0 50 kN, Pu 2.12 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What minimum axial load does 7212-BECBPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7212 BEP is the basic 60×110×22 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212-BECBPH",
      "7212 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7212 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 61,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 BECBY is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 61 kN, C0 50 kN, Pu 2.12 kN.reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 7,000 r/min reference; at dm ≈ 85.0 mm the corresponding dn is approximately 638k mm·r/min. Sizing arithmetic on the 60 mm bore: 61 kN C divided by the 25.0 mm radial section height gives 2.4 kN per section millimetre; the 800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 7,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7212-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "One 7212-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7212-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7212-BECBY?",
        "a": "7212 BECBY measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 800 g. SKF 17000 ratings: C 61 kN, C0 50 kN, Pu 2.12 kN, reference speed 7,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7212-BECBY?",
        "a": "The 7,000 r/min reference (thermal) and 7,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7212-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7212 BEP is the basic 60×110×22 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212-BECBY",
      "7212 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7212 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 61,
    "static_load_kN": 50,
    "fatigue_load_limit_kN": 2.12,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 BECBM is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 60×110×22 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 61 kN, C0 50 kN, Pu 2.12 kN.reference speed 7,000 r/min (thermal) and limiting speed 9,500 r/min (mechanical), catalogue mass 800 g. Mass and section check: 800 g inside the 60×110×22 mm outline leaves a 25.0 mm radial section, and the 50 kN static rating is 0.82× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 2.12 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 61/50 kN ratings and 800 g mass this execution carries about 1.02 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 7,000 r/min against a 9,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.74. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 22 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7212-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7212-BECBM?",
        "a": "7212 BECBM measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 800 g. SKF 17000 ratings: C 61 kN, C0 50 kN, Pu 2.12 kN, reference speed 7,000 r/min (thermal) and limiting speed 9,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7212-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; 7212 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (61/50 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7212 BEP is the basic 60×110×22 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212-BECBM",
      "7212 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7212-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7212 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 56,
    "fatigue_load_limit_kN": 2.36,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7212 ACCBM is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 60×110×22 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 69.5 kN, C0 56 kN, Pu 2.36 kN.reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 800 g. Load balance: C0 56 kN against C 69.5 kN gives a 0.81 ratio, typical of a steep-angle axial-oriented design; Pu 2.36 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 60 mm bore: 69.5 kN C divided by the 25.0 mm radial section height gives 2.8 kN per section millimetre; the 800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 22 mm width gives a bore/width ratio of 2.73; use these ratios when housing space around the 60 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 60 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The 25° AC angle of 7212-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7212-ACCBM?",
        "a": "7212 ACCBM measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 800 g. SKF 17000 ratings: C 69.5 kN, C0 56 kN, Pu 2.36 kN, reference speed 8,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7212-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7212-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 57.2/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (69.5/56 kN vs 96.5/93 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7212 BEP shares the 60×110×22 mm angular-contact envelope, but catalogue C/C0 differ (69.5/56 kN vs 57.2/45.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7212-ACCBM",
      "7212 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7312 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 3,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7312 BEP is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 60×130×31 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 95.6 kN, C0 69.5 kN, Pu 3 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 1750 g. Sizing arithmetic on the 60 mm bore: 95.6 kN C divided by the 35.0 mm radial section height gives 2.7 kN per section millimetre; the 1750 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 3 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 95.6/69.5 kN ratings and 1750 g mass this execution carries about 1.59 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 6,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.05. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7312-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7312 BEP as the single basic pa66 execution; the other order numbers of the 7312 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7312-BEP?",
        "a": "7312 BEP measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1750 g. SKF 17000 ratings: C 95.6 kN, C0 69.5 kN, Pu 3 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7312-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (95.6/69.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7312 BEP is the basic 60×130×31 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312-BEP",
      "7312 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7312 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 104,
    "static_load_kN": 76.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7312 BECBP is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 60×130×31 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 104 kN, C0 76.5 kN, Pu 3.2 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1750 g. Load balance: C0 76.5 kN against C 104 kN gives a 0.74 ratio, typical of a steep-angle axial-oriented design; Pu 3.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 60 mm bore: 104 kN C divided by the 35.0 mm radial section height gives 3.0 kN per section millimetre; the 1750 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7312-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7312-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7312-BECBP?",
        "a": "7312 BECBP measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1750 g. SKF 17000 ratings: C 104 kN, C0 76.5 kN, Pu 3.2 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7312-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (104/76.5 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312-BECBP",
      "7312 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7312 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 104,
    "static_load_kN": 76.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7312 BECBPH is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 60×130×31 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 104 kN, C0 76.5 kN, Pu 3.2 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1750 g. Sizing arithmetic on the 60 mm bore: 104 kN C divided by the 35.0 mm radial section height gives 3.0 kN per section millimetre; the 1750 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 31 mm width over a 35.0 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 1750 g for 104 kN of dynamic capacity — about 17 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "At 60 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7312-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7312-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7312-BECBPH?",
        "a": "7312 BECBPH measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1750 g. SKF 17000 ratings: C 104 kN, C0 76.5 kN, Pu 3.2 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Which grease and fill for 7312-BECBPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,700 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7312-BECBPH?",
        "a": "The 6,300 r/min reference (thermal) and 6,700 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (104/76.5 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312-BECBPH",
      "7312 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7312 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 104,
    "static_load_kN": 76.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7312 BECBY is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 60×130×31 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 104 kN, C0 76.5 kN, Pu 3.2 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1750 g. The 3.2 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 104/76.5 kN ratings and 1750 g mass this execution carries about 1.73 kN of C per millimetre of bore. Sizing arithmetic on the 60 mm bore: 104 kN C divided by the 35.0 mm radial section height gives 3.0 kN per section millimetre; the 1750 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7312-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 31 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7312-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7312-BECBY?",
        "a": "7312 BECBY measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1750 g. SKF 17000 ratings: C 104 kN, C0 76.5 kN, Pu 3.2 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7312-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 6,700 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7312-BECBY?",
        "a": "The 6,300 r/min reference (thermal) and 6,700 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (104/76.5 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312-BECBY",
      "7312 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7312 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 104,
    "static_load_kN": 76.5,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7312 BECBM is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 60×130×31 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 104 kN, C0 76.5 kN, Pu 3.2 kN.reference speed 6,300 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 1750 g. At the printed limiting speed of 8,500 r/min the mean pitch diameter dm ≈ 95.0 mm implies a dn value around 808k mm·r/min; the 6,300 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 31 mm width over a 35.0 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 1750 g for 104 kN of dynamic capacity — about 17 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 8,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.74. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 60 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "At 60 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7312-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7312-BECBM?",
        "a": "7312 BECBM measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1750 g. SKF 17000 ratings: C 104 kN, C0 76.5 kN, Pu 3.2 kN, reference speed 6,300 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7312-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7312-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 8,500 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; 7312 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (104/76.5 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (104/76.5 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312-BECBM",
      "7312 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7312-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7312 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 116,
    "static_load_kN": 85,
    "fatigue_load_limit_kN": 3.6,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7312 ACCBM is SKF's 60 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 60×130×31 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 116 kN, C0 85 kN, Pu 3.6 kN.reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 1750 g. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 95.0 mm implies a dn value around 950k mm·r/min; the 7,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 31 mm width over a 35.0 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 1750 g for 116 kN of dynamic capacity — about 15 g per rated kN. Bore-to-OD planning: OD 130 over bore 60 is a 2.17× step for this size, and the 31 mm width gives a bore/width ratio of 1.94; use these ratios when housing space around the 60 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7312-ACCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The 25° AC angle of 7312-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7312-ACCBM?",
        "a": "7312 ACCBM measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 1750 g. SKF 17000 ratings: C 116 kN, C0 85 kN, Pu 3.6 kN, reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7312-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (116/85 kN vs 156/137 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (116/85 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7312-ACCBM",
      "7312 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7213 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 66.3,
    "static_load_kN": 54,
    "fatigue_load_limit_kN": 2.28,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213 BEP is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 65×120×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 66.3 kN, C0 54 kN, Pu 2.28 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1000 g. The 2.28 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 66.3/54 kN ratings and 1000 g mass this execution carries about 1.02 kN of C per millimetre of bore. Sizing arithmetic on the 65 mm bore: 66.3 kN C divided by the 27.5 mm radial section height gives 2.4 kN per section millimetre; the 1000 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7213-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7213 BEP as the single basic pa66 execution; the other order numbers of the 7213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7213-BEP?",
        "a": "7213 BEP measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1000 g. SKF 17000 ratings: C 66.3 kN, C0 54 kN, Pu 2.28 kN, reference speed 6,700 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7213-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (66.3/54 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (66.3/54 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (66.3/54 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (66.3/54 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7213 BEP is the basic 65×120×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213-BEP",
      "7213 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7213 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213 BECBP is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 65×120×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 69.5 kN, C0 57 kN, Pu 2.45 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size, catalogue mass 1000 g. Mass and section check: 1000 g inside the 65×120×23 mm outline leaves a 27.5 mm radial section, and the 57 kN static rating is 0.82× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 2.45 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 69.5/57 kN ratings and 1000 g mass this execution carries about 1.07 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7213-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7213-BECBP?",
        "a": "7213 BECBP measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1000 g. SKF 17000 ratings: C 69.5 kN, C0 57 kN, Pu 2.45 kN, reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7213-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,700 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7213-BECBP?",
        "a": "The 6,700 r/min reference (thermal) and 6,700 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7213 BEP is the basic 65×120×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213-BECBP",
      "7213 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7213 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213 BECBY is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 65×120×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 69.5 kN, C0 57 kN, Pu 2.45 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size, catalogue mass 1000 g. Sizing arithmetic on the 65 mm bore: 69.5 kN C divided by the 27.5 mm radial section height gives 2.5 kN per section millimetre; the 1000 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 2.45 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 69.5/57 kN ratings and 1000 g mass this execution carries about 1.07 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 65 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7213-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7213-BECBY?",
        "a": "7213 BECBY measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1000 g. SKF 17000 ratings: C 69.5 kN, C0 57 kN, Pu 2.45 kN, reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7213-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7213 BEP is the basic 65×120×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213-BECBY",
      "7213 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7213 BEGAPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213 BEGAPH is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 65×120×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 69.5 kN, C0 57 kN, Pu 2.45 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size, catalogue mass 1000 g. The 2.45 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 69.5/57 kN ratings and 1000 g mass this execution carries about 1.07 kN of C per millimetre of bore. Selection figures for 7213 BEGAPH: the static-to-dynamic ratio C0/C is 0.82, Pu 2.45 kN is about 4 % of C, and catalogue mass works out to roughly 15 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEGAPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable BEGAPH unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEGAPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7213-BEGAPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7213-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7213-BEGAPH?",
        "a": "7213 BEGAPH measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1000 g. SKF 17000 ratings: C 69.5 kN, C0 57 kN, Pu 2.45 kN, reference speed 6,700 r/min (thermal) and limiting speed 6,700 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "Which grease and fill for 7213-BEGAPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,700 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7213-BEGAPH?",
        "a": "The 6,700 r/min reference (thermal) and 6,700 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7213 BEP is the basic 65×120×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213-BEGAPH",
      "7213 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7213 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 69.5,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213 BECBM is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 65×120×23 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 69.5 kN, C0 57 kN, Pu 2.45 kN.reference speed 6,700 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 1000 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 8,500 r/min while thermal balance under catalogue load sets the 6,700 r/min reference; at dm ≈ 92.5 mm the corresponding dn is approximately 786k mm·r/min. Selection figures for 7213 BECBM: the static-to-dynamic ratio C0/C is 0.82, Pu 2.45 kN is about 4 % of C, and catalogue mass works out to roughly 15 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 8,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.79. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7213-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7213-BECBM?",
        "a": "7213 BECBM measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1000 g. SKF 17000 ratings: C 69.5 kN, C0 57 kN, Pu 2.45 kN, reference speed 6,700 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7213-BECBM?",
        "a": "The 6,700 r/min reference (thermal) and 8,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7213-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; 7213 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (69.5/57 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7213 BEP is the basic 65×120×23 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213-BECBM",
      "7213 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7213-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7213 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 81.5,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.8,
    "reference_speed_rpm": 7000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 1000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7213 ACCBM is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 65×120×23 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 81.5 kN, C0 65.5 kN, Pu 2.8 kN.reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 1000 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 10,000 r/min while thermal balance under catalogue load sets the 7,000 r/min reference; at dm ≈ 92.5 mm the corresponding dn is approximately 925k mm·r/min. Selection figures for 7213 ACCBM: the static-to-dynamic ratio C0/C is 0.80, Pu 2.8 kN is about 3 % of C, and catalogue mass works out to roughly 15 g per millimetre of bore. Bore-to-OD planning: OD 120 over bore 65 is a 1.85× step for this size, and the 23 mm width gives a bore/width ratio of 2.83; use these ratios when housing space around the 65 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The 25° AC angle of 7213-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7213-ACCBM?",
        "a": "7213 ACCBM measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1000 g. SKF 17000 ratings: C 81.5 kN, C0 65.5 kN, Pu 2.8 kN, reference speed 7,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7213-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 66.3/54 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (81.5/65.5 kN vs 110/112 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7213 BEP shares the 65×120×23 mm angular-contact envelope, but catalogue C/C0 differ (81.5/65.5 kN vs 66.3/54 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7213-ACCBM",
      "7213 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7313 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 108,
    "static_load_kN": 80,
    "fatigue_load_limit_kN": 3.35,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 BEP is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 65×140×33 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 108 kN, C0 80 kN, Pu 3.35 kN.reference speed 6,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 2150 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 6,000 r/min reference; at dm ≈ 102.5 mm the corresponding dn is approximately 574k mm·r/min. Sizing arithmetic on the 65 mm bore: 108 kN C divided by the 37.5 mm radial section height gives 2.9 kN per section millimetre; the 2150 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.07. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "One 7313-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7313-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7313 BEP as the single basic pa66 execution; the other order numbers of the 7313 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7313-BEP?",
        "a": "7313 BEP measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2150 g. SKF 17000 ratings: C 108 kN, C0 80 kN, Pu 3.35 kN, reference speed 6,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7313-BEP?",
        "a": "The 6,000 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7313-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (108/80 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (108/80 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (108/80 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7313 BEP is the basic 65×140×33 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313-BEP",
      "7313 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7313 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 116,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 BECBP is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 65×140×33 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 116 kN, C0 86.5 kN, Pu 3.65 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 2150 g. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 646k mm·r/min; the 6,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 33 mm width over a 37.5 mm section yields 0.88 mm of ring width per section millimetre, and the bearing weighs 2150 g for 116 kN of dynamic capacity — about 19 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7313-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7313-BECBP?",
        "a": "7313 BECBP measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2150 g. SKF 17000 ratings: C 116 kN, C0 86.5 kN, Pu 3.65 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7313-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7313-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7313 BEP is the basic 65×140×33 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313-BECBP",
      "7313 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7313 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 116,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 BECBPH is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 65×140×33 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 116 kN, C0 86.5 kN, Pu 3.65 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 2150 g. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 646k mm·r/min; the 6,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 6,300 r/min while thermal balance under catalogue load sets the 6,000 r/min reference; at dm ≈ 102.5 mm the corresponding dn is approximately 646k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7313-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7313-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7313-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7313-BECBPH?",
        "a": "7313 BECBPH measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2150 g. SKF 17000 ratings: C 116 kN, C0 86.5 kN, Pu 3.65 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Which fits should I use for 7313-BECBPH?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7313-BECBPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7313 BEP is the basic 65×140×33 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313-BECBPH",
      "7313 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7313 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 116,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 BECBY is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 65×140×33 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 116 kN, C0 86.5 kN, Pu 3.65 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 2150 g. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 646k mm·r/min; the 6,000 r/min reference speed is the thermal-planning figure under catalogue load. The 3.65 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 116/86.5 kN ratings and 2150 g mass this execution carries about 1.78 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7313-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7313-BECBY?",
        "a": "7313 BECBY measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2150 g. SKF 17000 ratings: C 116 kN, C0 86.5 kN, Pu 3.65 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7313-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7313 BEP is the basic 65×140×33 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313-BECBY",
      "7313 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7313 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 116,
    "static_load_kN": 86.5,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 BECBM is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 65×140×33 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 116 kN, C0 86.5 kN, Pu 3.65 kN.reference speed 6,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 2150 g. Load balance: C0 86.5 kN against C 116 kN gives a 0.75 ratio, typical of a steep-angle axial-oriented design; Pu 3.65 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 65 mm bore: 116 kN C divided by the 37.5 mm radial section height gives 3.1 kN per section millimetre; the 2150 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 8,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.75. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7313-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 65 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7313-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7313-BECBM?",
        "a": "7313 BECBM measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2150 g. SKF 17000 ratings: C 116 kN, C0 86.5 kN, Pu 3.65 kN, reference speed 6,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7313-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; 7313 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (116/86.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7313 BEP is the basic 65×140×33 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313-BECBM",
      "7313 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7313-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7313 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 132,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 4.05,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7313 ACCBM is SKF's 65 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 65×140×33 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 132 kN, C0 96.5 kN, Pu 4.05 kN.reference speed 6,300 r/min (thermal) and limiting speed 9,500 r/min (mechanical), catalogue mass 2150 g. Mass and section check: 2150 g inside the 65×140×33 mm outline leaves a 37.5 mm radial section, and the 96.5 kN static rating is 0.73× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 4.05 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 132/96.5 kN ratings and 2150 g mass this execution carries about 2.03 kN of C per millimetre of bore. Bore-to-OD planning: OD 140 over bore 65 is a 2.15× step for this size, and the 33 mm width gives a bore/width ratio of 1.97; use these ratios when housing space around the 65 mm shaft is the first constraint. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 0,55 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The 25° AC angle of 7313-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7313-ACCBM?",
        "a": "7313 ACCBM measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2150 g. SKF 17000 ratings: C 132 kN, C0 96.5 kN, Pu 4.05 kN, reference speed 6,300 r/min (thermal) and limiting speed 9,500 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7313-ACCBM?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 108/80 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (132/96.5 kN vs 176/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7313 BEP shares the 65×140×33 mm angular-contact envelope, but catalogue C/C0 differ (132/96.5 kN vs 108/80 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7313-ACCBM",
      "7313 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7214 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 67.6,
    "static_load_kN": 56,
    "fatigue_load_limit_kN": 2.36,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 BEP is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 70×125×24 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 67.6 kN, C0 56 kN, Pu 2.36 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 1100 g. Envelope economics: the 24 mm width over a 27.5 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 1100 g for 67.6 kN of dynamic capacity — about 16 g per rated kN. Mass and section check: 1100 g inside the 70×125×24 mm outline leaves a 27.5 mm radial section, and the 56 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 24 mm width gives a bore/width ratio of 2.92; use these ratios when housing space around the 70 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "At 70 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7214-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7214-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7214 BEP as the single basic pa66 execution; the other order numbers of the 7214 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7214-BEP?",
        "a": "7214 BEP measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1100 g. SKF 17000 ratings: C 67.6 kN, C0 56 kN, Pu 2.36 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7214-BEP?",
        "a": "The 6,300 r/min reference (thermal) and 6,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7214-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (67.6/56 kN vs 75/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (67.6/56 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (67.6/56 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (67.6/56 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (67.6/56 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7214 BEP is the basic 70×125×24 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214-BEP",
      "7214 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7214 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 72,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 BECBP is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 70×125×24 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 72 kN, C0 60 kN, Pu 2.55 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size, catalogue mass 1100 g. Selection figures for 7214 BECBP: the static-to-dynamic ratio C0/C is 0.83, Pu 2.55 kN is about 4 % of C, and catalogue mass works out to roughly 16 g per millimetre of bore. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 97.5 mm implies a dn value around 614k mm·r/min; the 6,300 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 24 mm width gives a bore/width ratio of 2.92; use these ratios when housing space around the 70 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "One 7214-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7214-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7214-BECBP?",
        "a": "7214 BECBP measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1100 g. SKF 17000 ratings: C 72 kN, C0 60 kN, Pu 2.55 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7214-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 70 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7214-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7214 BEP is the basic 70×125×24 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214-BECBP",
      "7214 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7214 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 72,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 BECBPH is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 70×125×24 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 72 kN, C0 60 kN, Pu 2.55 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size, catalogue mass 1100 g. Selection figures for 7214 BECBPH: the static-to-dynamic ratio C0/C is 0.83, Pu 2.55 kN is about 4 % of C, and catalogue mass works out to roughly 16 g per millimetre of bore. Envelope economics: the 24 mm width over a 27.5 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 1100 g for 72 kN of dynamic capacity — about 15 g per rated kN. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 24 mm width gives a bore/width ratio of 2.92; use these ratios when housing space around the 70 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7214-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7214-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7214-BECBPH?",
        "a": "7214 BECBPH measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1100 g. SKF 17000 ratings: C 72 kN, C0 60 kN, Pu 2.55 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What minimum axial load does 7214-BECBPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7214 BEP is the basic 70×125×24 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214-BECBPH",
      "7214 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7214 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 72,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.55,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 BECBM is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 70×125×24 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 72 kN, C0 60 kN, Pu 2.55 kN.reference speed 6,300 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 1100 g. Sizing arithmetic on the 70 mm bore: 72 kN C divided by the 27.5 mm radial section height gives 2.6 kN per section millimetre; the 1100 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 1100 g inside the 70×125×24 mm outline leaves a 27.5 mm radial section, and the 60 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 24 mm width gives a bore/width ratio of 2.92; use these ratios when housing space around the 70 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 24 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7214-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7214-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7214-BECBM?",
        "a": "7214 BECBM measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1100 g. SKF 17000 ratings: C 72 kN, C0 60 kN, Pu 2.55 kN, reference speed 6,300 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7214-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 70 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (72/60 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7214 BEP is the basic 70×125×24 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214-BECBM",
      "7214 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7214 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 75,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 BECBY is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 70×125×24 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 75 kN, C0 64 kN, Pu 2.7 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size, catalogue mass 1100 g. Selection figures for 7214 BECBY: the static-to-dynamic ratio C0/C is 0.85, Pu 2.7 kN is about 4 % of C, and catalogue mass works out to roughly 16 g per millimetre of bore. Load balance: C0 64 kN against C 75 kN gives a 0.85 ratio, typical of a steep-angle axial-oriented design; Pu 2.7 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 24 mm width gives a bore/width ratio of 2.92; use these ratios when housing space around the 70 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Fillet radii must clear the chamfer so the 24 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7214-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7214-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7214-BECBY?",
        "a": "7214 BECBY measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1100 g. SKF 17000 ratings: C 75 kN, C0 64 kN, Pu 2.7 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7214-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (75/64 kN vs 67.6/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; 7214 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (75/64 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (75/64 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (75/64 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (75/64 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7214 BEP shares the 70×125×24 mm angular-contact envelope, but catalogue C/C0 differ (75/64 kN vs 67.6/56 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214-BECBY",
      "7214 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7214-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7214 ACCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 83,
    "static_load_kN": 68,
    "fatigue_load_limit_kN": 2.9,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 1100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7214 ACCBM is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 25° (AC) contact angle, 70×125×24 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 83 kN, C0 68 kN, Pu 2.9 kN.reference speed 6,700 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 1100 g. Sizing arithmetic on the 70 mm bore: 83 kN C divided by the 27.5 mm radial section height gives 3.0 kN per section millimetre; the 1100 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 1100 g inside the 70×125×24 mm outline leaves a 27.5 mm radial section, and the 68 kN static rating is 0.82× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 10,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.67. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7214-ACCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Do not mix execution classes inside one set: a universally matchable ACCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "The 25° AC angle of 7214-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7214-ACCBM?",
        "a": "7214 ACCBM measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1100 g. SKF 17000 ratings: C 83 kN, C0 68 kN, Pu 2.9 kN, reference speed 6,700 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7214-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7214-ACCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 67.6/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 75/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (83/68 kN vs 120/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7214 BEP shares the 70×125×24 mm angular-contact envelope, but catalogue C/C0 differ (83/68 kN vs 67.6/56 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7214-ACCBM",
      "7214 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7314 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 119,
    "static_load_kN": 90,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 BEP is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 119 kN, C0 90 kN, Pu 3.65 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 2650 g. Load balance: C0 90 kN against C 119 kN gives a 0.76 ratio, typical of a steep-angle axial-oriented design; Pu 3.65 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 2650 g inside the 70×150×35 mm outline leaves a 40.0 mm radial section, and the 90 kN static rating is 0.76× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7314-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7314-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7314 BEP as the single basic pa66 execution; the other order numbers of the 7314 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-BEP?",
        "a": "7314 BEP measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 119 kN, C0 90 kN, Pu 3.65 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Can one 7314-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7314-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (119/90 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (119/90 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (119/90 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (119/90 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7314 BEP is the basic 70×150×35 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-BEP",
      "7314 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7314 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 127,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.9,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 BECBP is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 127 kN, C0 98 kN, Pu 3.9 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. The 3.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 127/98 kN ratings and 2650 g mass this execution carries about 1.81 kN of C per millimetre of bore. Load balance: C0 98 kN against C 127 kN gives a 0.77 ratio, typical of a steep-angle axial-oriented design; Pu 3.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7314-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "One 7314-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "At 70 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7314-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-BECBP?",
        "a": "7314 BECBP measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 127 kN, C0 98 kN, Pu 3.9 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7314-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 70 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7314 BEP is the basic 70×150×35 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-BECBP",
      "7314 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7314 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 127,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.9,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 BECBPH is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 127 kN, C0 98 kN, Pu 3.9 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. Load balance: C0 98 kN against C 127 kN gives a 0.77 ratio, typical of a steep-angle axial-oriented design; Pu 3.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 616k mm·r/min. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 35 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7314-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-BECBPH?",
        "a": "7314 BECBPH measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 127 kN, C0 98 kN, Pu 3.9 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Can one 7314-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7314-BECBPH need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7314 BEP is the basic 70×150×35 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-BECBPH",
      "7314 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7314 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 127,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.9,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 BECBY is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 127 kN, C0 98 kN, Pu 3.9 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. Mass and section check: 2650 g inside the 70×150×35 mm outline leaves a 40.0 mm radial section, and the 98 kN static rating is 0.77× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 98 kN against C 127 kN gives a 0.77 ratio, typical of a steep-angle axial-oriented design; Pu 3.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7314-BECBY of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 35 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7314-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-BECBY?",
        "a": "7314 BECBY measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 127 kN, C0 98 kN, Pu 3.9 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Can one 7314-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7314-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7314 BEP is the basic 70×150×35 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-BECBY",
      "7314 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7314 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 127,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.9,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 BEGAPH is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 127 kN, C0 98 kN, Pu 3.9 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. Load balance: C0 98 kN against C 127 kN gives a 0.77 ratio, typical of a steep-angle axial-oriented design; Pu 3.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 616k mm·r/min. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7314-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-BEGAPH?",
        "a": "7314 BEGAPH measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 127 kN, C0 98 kN, Pu 3.9 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7314-BEGAPH?",
        "a": "With a rotating inner ring use roughly k5 on the 70 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7314 BEP is the basic 70×150×35 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-BEGAPH",
      "7314 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7314 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 127,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.9,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 BECBM is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 127 kN, C0 98 kN, Pu 3.9 kN.reference speed 5,600 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 2650 g. Envelope economics: the 35 mm width over a 40.0 mm section yields 0.88 mm of ring width per section millimetre, and the bearing weighs 2650 g for 127 kN of dynamic capacity — about 21 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,000 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 770k mm·r/min. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7314-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7314-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7314-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-BECBM?",
        "a": "7314 BECBM measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 127 kN, C0 98 kN, Pu 3.9 kN, reference speed 5,600 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7314-BECBM?",
        "a": "The 5,600 r/min reference (thermal) and 7,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7314-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; 7314 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (127/98 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7314 BEP is the basic 70×150×35 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-BECBM",
      "7314 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7314-ACCBM",
    "brand": "SKF",
    "manufacturer_designation": "7314 ACCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 143,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7314 ACCBM is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 25° (AC) contact angle, 70×150×35 mm to the ISO dimension plan. AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 143 kN, C0 110 kN, Pu 4.4 kN.reference speed 6,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 2650 g. Selection figures for 7314 ACCBM: the static-to-dynamic ratio C0/C is 0.77, Pu 4.4 kN is about 3 % of C, and catalogue mass works out to roughly 38 g per millimetre of bore. At the printed limiting speed of 8,500 r/min the mean pitch diameter dm ≈ 110.0 mm implies a dn value around 935k mm·r/min; the 6,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 6,000 r/min against a 8,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.71. High-angle alternative note: ACCBM carries the 25-degree AC contact angle (not the 40-degree B), CB Normal-clearance universal faces and a machined brass cage; it runs faster and cooler than a BECBM of the same envelope but accepts a smaller axial share, so substitute only after re-running the load-ratio check.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "ball unloading when the 25-degree AC set is applied at the Fa/Fr ratios valid only for the 40-degree B design",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 35 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of ACCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 35 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The 25° AC angle of 7314-ACCBM runs faster and cooler than a 40° B bearing of the same envelope, but its thrust capacity and induced-load behaviour differ — do not swap AC for B without re-running the axial-load calculation.",
      "Universally matchable ACCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7314-ACCBM?",
        "a": "7314 ACCBM measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 2650 g. SKF 17000 ratings: C 143 kN, C0 110 kN, Pu 4.4 kN, reference speed 6,000 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the ACCBM suffix mean?",
        "a": "AC sets the 25° contact angle, CB marks universal matching with Normal axial clearance, and M the machined brass ball-centred cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7314-ACCBM?",
        "a": "The 6,000 r/min reference (thermal) and 8,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7314-ACCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 25° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 119/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (143/110 kN vs 200/180 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7314 BEP shares the 70×150×35 mm angular-contact envelope, but catalogue C/C0 differ (143/110 kN vs 119/90 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7314-ACCBM",
      "7314 ACCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7215 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 70.2,
    "static_load_kN": 60,
    "fatigue_load_limit_kN": 2.5,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7215 BEP is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 75×130×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 70.2 kN, C0 60 kN, Pu 2.5 kN.reference speed 6,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 1200 g. Mass and section check: 1200 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 60 kN static rating is 0.85× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 60 kN against C 70.2 kN gives a 0.85 ratio, typical of a steep-angle axial-oriented design; Pu 2.5 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "At 75 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7215-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7215 BEP as the single basic pa66 execution; the other order numbers of the 7215 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7215-BEP?",
        "a": "7215 BEP measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1200 g. SKF 17000 ratings: C 70.2 kN, C0 60 kN, Pu 2.5 kN, reference speed 6,000 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7215-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 5,600 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7215-BEP?",
        "a": "The 6,000 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (70.2/60 kN vs 76.5/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (70.2/60 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (70.2/60 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (70.2/60 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7215 BEP is the basic 75×130×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215-BEP",
      "7215 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7215 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7215 BECBM is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 75×130×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 73.5 kN, C0 65.5 kN, Pu 2.7 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1200 g. Selection figures for 7215 BECBM: the static-to-dynamic ratio C0/C is 0.89, Pu 2.7 kN is about 4 % of C, and catalogue mass works out to roughly 16 g per millimetre of bore. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 646k mm·r/min; the 6,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7215-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7215-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7215-BECBM?",
        "a": "7215 BECBM measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 65.5 kN, Pu 2.7 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7215-BECBM?",
        "a": "The 6,000 r/min reference (thermal) and 6,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7215-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7215 BEP is the basic 75×130×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215-BECBM",
      "7215 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7215 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7215 BECBP is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 75×130×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 73.5 kN, C0 65.5 kN, Pu 2.7 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1200 g. Sizing arithmetic on the 75 mm bore: 73.5 kN C divided by the 27.5 mm radial section height gives 2.7 kN per section millimetre; the 1200 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 1200 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 65.5 kN static rating is 0.89× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7215-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7215-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7215-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7215-BECBP?",
        "a": "7215 BECBP measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 65.5 kN, Pu 2.7 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7215-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7215-BECBP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7215 BEP is the basic 75×130×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215-BECBP",
      "7215 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7215 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 65.5,
    "fatigue_load_limit_kN": 2.7,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7215 BECBPH is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 75×130×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 73.5 kN, C0 65.5 kN, Pu 2.7 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1200 g. Mass and section check: 1200 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 65.5 kN static rating is 0.89× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 646k mm·r/min; the 6,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7215-BECBPH of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Fillet radii must clear the chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7215-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7215-BECBPH?",
        "a": "7215 BECBPH measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 65.5 kN, Pu 2.7 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "Which grease and fill for 7215-BECBPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 6,300 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7215-BECBPH?",
        "a": "The 6,000 r/min reference (thermal) and 6,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (73.5/65.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7215 BEP is the basic 75×130×25 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215-BECBPH",
      "7215 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7215-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7215 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 76.5,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 2.9,
    "reference_speed_rpm": 6000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7215 BECBY is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 75×130×25 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 76.5 kN, C0 69.5 kN, Pu 2.9 kN.reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1200 g. Load balance: C0 69.5 kN against C 76.5 kN gives a 0.91 ratio, typical of a steep-angle axial-oriented design; Pu 2.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 1200 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 69.5 kN static rating is 0.91× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "One 7215-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7215-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7215-BECBY?",
        "a": "7215 BECBY measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1200 g. SKF 17000 ratings: C 76.5 kN, C0 69.5 kN, Pu 2.9 kN, reference speed 6,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7215-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 6,300 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7215-BECBY?",
        "a": "The 6,000 r/min reference (thermal) and 6,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (76.5/69.5 kN vs 70.2/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; 7215 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (76.5/69.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (76.5/69.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (76.5/69.5 kN vs 125/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7215 BEP shares the 75×130×25 mm angular-contact envelope, but catalogue C/C0 differ (76.5/69.5 kN vs 70.2/60 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7215-BECBY",
      "7215 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7315 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 125,
    "static_load_kN": 98,
    "fatigue_load_limit_kN": 3.8,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7315 BEP is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 75×160×37 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 125 kN, C0 98 kN, Pu 3.8 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 3200 g. Selection figures for 7315 BEP: the static-to-dynamic ratio C0/C is 0.78, Pu 3.8 kN is about 3 % of C, and catalogue mass works out to roughly 43 g per millimetre of bore. Load balance: C0 98 kN against C 125 kN gives a 0.78 ratio, typical of a steep-angle axial-oriented design; Pu 3.8 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 160 over bore 75 is a 2.13× step for this size, and the 37 mm width gives a bore/width ratio of 2.03; use these ratios when housing space around the 75 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 75 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "One 7315-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7315-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7315 BEP as the single basic pa66 execution; the other order numbers of the 7315 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7315-BEP?",
        "a": "7315 BEP measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3200 g. SKF 17000 ratings: C 125 kN, C0 98 kN, Pu 3.8 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7315-BEP?",
        "a": "The 5,300 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7315-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (125/98 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (125/98 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7315 BEP is the basic 75×160×37 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315-BEP",
      "7315 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7315 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 132,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7315 BECBP is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 75×160×37 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 132 kN, C0 104 kN, Pu 4.15 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 3200 g. Envelope economics: the 37 mm width over a 42.5 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 3200 g for 132 kN of dynamic capacity — about 24 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 5,300 r/min reference; at dm ≈ 117.5 mm the corresponding dn is approximately 623k mm·r/min. Bore-to-OD planning: OD 160 over bore 75 is a 2.13× step for this size, and the 37 mm width gives a bore/width ratio of 2.03; use these ratios when housing space around the 75 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7315-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7315-BECBP?",
        "a": "7315 BECBP measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3200 g. SKF 17000 ratings: C 132 kN, C0 104 kN, Pu 4.15 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7315-BECBP?",
        "a": "The 5,300 r/min reference (thermal) and 5,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7315-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7315 BEP is the basic 75×160×37 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315-BECBP",
      "7315 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7315 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 132,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7315 BECBY is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 75×160×37 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 132 kN, C0 104 kN, Pu 4.15 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 3200 g. Envelope economics: the 37 mm width over a 42.5 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 3200 g for 132 kN of dynamic capacity — about 24 g per rated kN. Mass and section check: 3200 g inside the 75×160×37 mm outline leaves a 42.5 mm radial section, and the 104 kN static rating is 0.79× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 160 over bore 75 is a 2.13× step for this size, and the 37 mm width gives a bore/width ratio of 2.03; use these ratios when housing space around the 75 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "At 75 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly k5 on a 75 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7315-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7315-BECBY?",
        "a": "7315 BECBY measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3200 g. SKF 17000 ratings: C 132 kN, C0 104 kN, Pu 4.15 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which fits should I use for 7315-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 75 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7315-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 5,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7315 BEP is the basic 75×160×37 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315-BECBY",
      "7315 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7315 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 132,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7315 BEGAPH is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 75×160×37 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 132 kN, C0 104 kN, Pu 4.15 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 3200 g. Envelope economics: the 37 mm width over a 42.5 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 3200 g for 132 kN of dynamic capacity — about 24 g per rated kN. Selection figures for 7315 BEGAPH: the static-to-dynamic ratio C0/C is 0.79, Pu 4.15 kN is about 3 % of C, and catalogue mass works out to roughly 43 g per millimetre of bore. Bore-to-OD planning: OD 160 over bore 75 is a 2.13× step for this size, and the 37 mm width gives a bore/width ratio of 2.03; use these ratios when housing space around the 75 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "One 7315-BEGAPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 75 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7315-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7315-BEGAPH?",
        "a": "7315 BEGAPH measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3200 g. SKF 17000 ratings: C 132 kN, C0 104 kN, Pu 4.15 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7315-BEGAPH?",
        "a": "The 5,300 r/min reference (thermal) and 5,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7315-BEGAPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7315 BEP is the basic 75×160×37 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315-BEGAPH",
      "7315 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7315-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7315 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 132,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 3200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7315 BECBM is SKF's 75 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 75×160×37 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 132 kN, C0 104 kN, Pu 4.15 kN.reference speed 5,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 3200 g. The 4.15 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 132/104 kN ratings and 3200 g mass this execution carries about 1.76 kN of C per millimetre of bore. Load balance: C0 104 kN against C 132 kN gives a 0.79 ratio, typical of a steep-angle axial-oriented design; Pu 4.15 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 160 over bore 75 is a 2.13× step for this size, and the 37 mm width gives a bore/width ratio of 2.03; use these ratios when housing space around the 75 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7315-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7315-BECBM?",
        "a": "7315 BECBM measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3200 g. SKF 17000 ratings: C 132 kN, C0 104 kN, Pu 4.15 kN, reference speed 5,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7315-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7315-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; 7315 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (132/104 kN vs 216/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7315 BEP is the basic 75×160×37 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7315-BECBM",
      "7315 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7216 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 80.6,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 2.8,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 BEP is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 80×140×26 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 80.6 kN, C0 69.5 kN, Pu 2.8 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 1450 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 583k mm·r/min. Sizing arithmetic on the 80 mm bore: 80.6 kN C divided by the 30.0 mm radial section height gives 2.7 kN per section millimetre; the 1450 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 5,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 26 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "One 7216-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7216-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7216 BEP as the single basic pa66 execution; the other order numbers of the 7216 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7216-BEP?",
        "a": "7216 BEP measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1450 g. SKF 17000 ratings: C 80.6 kN, C0 69.5 kN, Pu 2.8 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7216-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (80.6/69.5 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (80.6/69.5 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7216 BEP is the basic 80×140×26 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216-BEP",
      "7216 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7216 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 85,
    "static_load_kN": 75,
    "fatigue_load_limit_kN": 3.05,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 BECBP is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 80×140×26 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 85 kN, C0 75 kN, Pu 3.05 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 1450 g. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 110.0 mm implies a dn value around 616k mm·r/min; the 5,600 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 26 mm width over a 30.0 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 1450 g for 85 kN of dynamic capacity — about 17 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "Assign interference to the rotating ring — roughly k5 on a 80 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7216-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7216-BECBP?",
        "a": "7216 BECBP measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1450 g. SKF 17000 ratings: C 85 kN, C0 75 kN, Pu 3.05 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7216-BECBP?",
        "a": "The 5,600 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7216-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7216 BEP is the basic 80×140×26 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216-BECBP",
      "7216 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7216 BECBPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 85,
    "static_load_kN": 75,
    "fatigue_load_limit_kN": 3.05,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 BECBPH is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 80×140×26 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 85 kN, C0 75 kN, Pu 3.05 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 1450 g. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 110.0 mm implies a dn value around 616k mm·r/min; the 5,600 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 616k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 80 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Fillet radii must clear the chamfer so the 26 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BECBPH unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7216-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7216-BECBPH?",
        "a": "7216 BECBPH measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1450 g. SKF 17000 ratings: C 85 kN, C0 75 kN, Pu 3.05 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7216-BECBPH?",
        "a": "The 5,600 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7216-BECBPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7216 BEP is the basic 80×140×26 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216-BECBPH",
      "7216 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7216 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 85,
    "static_load_kN": 75,
    "fatigue_load_limit_kN": 3.05,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 BECBY is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 80×140×26 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 85 kN, C0 75 kN, Pu 3.05 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 1450 g. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 110.0 mm implies a dn value around 616k mm·r/min; the 5,600 r/min reference speed is the thermal-planning figure under catalogue load. The 3.05 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 85/75 kN ratings and 1450 g mass this execution carries about 1.06 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7216-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7216-BECBY?",
        "a": "7216 BECBY measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1450 g. SKF 17000 ratings: C 85 kN, C0 75 kN, Pu 3.05 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7216-BECBY?",
        "a": "The 5,600 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7216-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7216 BEP is the basic 80×140×26 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216-BECBY",
      "7216 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7216 BEGAPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 85,
    "static_load_kN": 75,
    "fatigue_load_limit_kN": 3.05,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 BEGAPH is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 80×140×26 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 85 kN, C0 75 kN, Pu 3.05 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 1450 g. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 110.0 mm implies a dn value around 616k mm·r/min; the 5,600 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 5,600 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 616k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEGAPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEGAPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7216-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7216-BEGAPH?",
        "a": "7216 BEGAPH measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1450 g. SKF 17000 ratings: C 85 kN, C0 75 kN, Pu 3.05 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7216-BEGAPH?",
        "a": "The 5,600 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7216-BEGAPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7216 BEP is the basic 80×140×26 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216-BEGAPH",
      "7216 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7216-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7216 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 85,
    "static_load_kN": 75,
    "fatigue_load_limit_kN": 3.05,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7216 BECBM is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 80×140×26 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 85 kN, C0 75 kN, Pu 3.05 kN.reference speed 5,600 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 1450 g. Load balance: C0 75 kN against C 85 kN gives a 0.88 ratio, typical of a steep-angle axial-oriented design; Pu 3.05 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 80 mm bore: 85 kN C divided by the 30.0 mm radial section height gives 2.8 kN per section millimetre; the 1450 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.80. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7216-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7216-BECBM?",
        "a": "7216 BECBM measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1450 g. SKF 17000 ratings: C 85 kN, C0 75 kN, Pu 3.05 kN, reference speed 5,600 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7216-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 7,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7216-BECBM?",
        "a": "The 5,600 r/min reference (thermal) and 7,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; 7216 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (85/75 kN vs 146/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7216 BEP is the basic 80×140×26 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7216-BECBM",
      "7216 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7316 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 135,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316 BEP is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 135 kN, C0 110 kN, Pu 4.15 kN.reference speed 5,000 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 3800 g. The 4.15 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 135/110 kN ratings and 3800 g mass this execution carries about 1.69 kN of C per millimetre of bore. Sizing arithmetic on the 80 mm bore: 135 kN C divided by the 45.0 mm radial section height gives 3.0 kN per section millimetre; the 3800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.11. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7316-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7316-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7316 BEP as the single basic pa66 execution; the other order numbers of the 7316 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7316-BEP?",
        "a": "7316 BEP measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 3800 g. SKF 17000 ratings: C 135 kN, C0 110 kN, Pu 4.15 kN, reference speed 5,000 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7316-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,500 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7316-BEP?",
        "a": "The 5,000 r/min reference (thermal) and 4,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (135/110 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (135/110 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7316 BEP is the basic 80×170×39 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316-BEP",
      "7316 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-BEM",
    "brand": "SKF",
    "manufacturer_designation": "7316 BEM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 135,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316 BEM is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 135 kN, C0 110 kN, Pu 4.15 kN.reference speed 5,000 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 3800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 5,000 r/min reference; at dm ≈ 125.0 mm the corresponding dn is approximately 600k mm·r/min. Sizing arithmetic on the 80 mm bore: 135 kN C divided by the 45.0 mm radial section height gives 3.0 kN per section millimetre; the 3800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 4,800 r/min limiting speed, i.e. a reference-to-limit ratio of 1.04. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BEM unit is ground for arbitrary pairing, a basic execution is not.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7316-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7316 BEM as the single basic machined brass execution; the other order numbers of the 7316 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7316-BEM?",
        "a": "7316 BEM measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 3800 g. SKF 17000 ratings: C 135 kN, C0 110 kN, Pu 4.15 kN, reference speed 5,000 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BEM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.."
      },
      {
        "q": "Which fits should I use for 7316-BEM?",
        "a": "With a rotating inner ring use roughly k5 on the 80 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7316-BEM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,800 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (135/110 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (135/110 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7316 BEP is the basic 80×170×39 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316-BEM",
      "7316 BEM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7316 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 143,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316 BECBP is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 143 kN, C0 118 kN, Pu 4.5 kN.reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size, catalogue mass 3800 g. Mass and section check: 3800 g inside the 80×170×39 mm outline leaves a 45.0 mm radial section, and the 118 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 4.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 143/118 kN ratings and 3800 g mass this execution carries about 1.79 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 5,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7316-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Fillet radii must clear the chamfer so the 39 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7316-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7316-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7316-BECBP?",
        "a": "7316 BECBP measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 3800 g. SKF 17000 ratings: C 143 kN, C0 118 kN, Pu 4.5 kN, reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7316-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 5,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7316-BECBP?",
        "a": "The 5,000 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7316 BEP is the basic 80×170×39 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316-BECBP",
      "7316 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-BECBPH",
    "brand": "SKF",
    "manufacturer_designation": "7316 BECBPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 143,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316 BECBPH is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 143 kN, C0 118 kN, Pu 4.5 kN.reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size, catalogue mass 3800 g. The 4.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 143/118 kN ratings and 3800 g mass this execution carries about 1.79 kN of C per millimetre of bore. Selection figures for 7316 BECBPH: the static-to-dynamic ratio C0/C is 0.83, Pu 4.5 kN is about 3 % of C, and catalogue mass works out to roughly 48 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 5,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. PEEK cage note: the PH cage is moulded from glass-fibre reinforced polyetheretherketone, ball-centred, aimed at high-speed oil-air and grease positions where PA66 would approach its thermal and speed limits; it needs clean lubricant (PEEK cages are sensitive to hard-particle cage-wear) and is a separate order number from the brass BECBM.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear from hard particles in the lubricant, which abrade the moulded pocket surfaces",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7316-BECBPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7316-BECBPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7316-BECBPH?",
        "a": "7316 BECBPH measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 3800 g. SKF 17000 ratings: C 143 kN, C0 118 kN, Pu 4.5 kN, reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBPH combines CB universal clearance with a PEEK ball-centred cage for hot, high-speed positions where PA66 is unsuitable."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7316-BECBPH?",
        "a": "With a rotating inner ring use roughly k5 on the 80 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7316 BEP is the basic 80×170×39 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316-BECBPH",
      "7316 BECBPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7316 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 143,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316 BECBY is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 143 kN, C0 118 kN, Pu 4.5 kN.reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size, catalogue mass 3800 g. Sizing arithmetic on the 80 mm bore: 143 kN C divided by the 45.0 mm radial section height gives 3.2 kN per section millimetre; the 3800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 4.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 143/118 kN ratings and 3800 g mass this execution carries about 1.79 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 5,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 39 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7316-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7316-BECBY?",
        "a": "7316 BECBY measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 3800 g. SKF 17000 ratings: C 143 kN, C0 118 kN, Pu 4.5 kN, reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7316-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 5,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7316-BECBY?",
        "a": "The 5,000 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7316 BEP is the basic 80×170×39 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316-BECBY",
      "7316 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7316-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7316 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 143,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 3800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7316 BECBM is SKF's 80 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 80×170×39 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 143 kN, C0 118 kN, Pu 4.5 kN.reference speed 5,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 3800 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 6,300 r/min while thermal balance under catalogue load sets the 5,000 r/min reference; at dm ≈ 125.0 mm the corresponding dn is approximately 788k mm·r/min. Selection figures for 7316 BECBM: the static-to-dynamic ratio C0/C is 0.83, Pu 4.5 kN is about 3 % of C, and catalogue mass works out to roughly 48 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.79. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "One 7316-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 80 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 39 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7316-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7316-BECBM?",
        "a": "7316 BECBM measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 3800 g. SKF 17000 ratings: C 143 kN, C0 118 kN, Pu 4.5 kN, reference speed 5,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7316-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; 7316 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (143/118 kN vs 232/228 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7316 BEP is the basic 80×170×39 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7316-BECBM",
      "7316 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7217 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.25,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7217 BEP is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 85×150×28 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 85×150×28 mm (3.346×5.906×1.102 in), 32.5 mm radial section height, C 95.6 kN, C0 83 kN, Pu 3.25 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 1850 g. Sizing arithmetic on the 85 mm bore: 95.6 kN C divided by the 32.5 mm radial section height gives 2.9 kN per section millimetre; the 1850 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 3.25 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 95.6/83 kN ratings and 1850 g mass this execution carries about 1.12 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,300 r/min against a 5,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 28 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7217-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7217 BEP as the single basic pa66 execution; the other order numbers of the 7217 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7217-BEP?",
        "a": "7217 BEP measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 1850 g. SKF 17000 ratings: C 95.6 kN, C0 83 kN, Pu 3.25 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7217-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 5,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7217-BEP?",
        "a": "The 5,300 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-217-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-217-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7217 BEP is the basic 85×150×28 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217-BEP",
      "7217 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7217 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 102,
    "static_load_kN": 90,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7217 BECBP is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 85×150×28 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 85×150×28 mm (3.346×5.906×1.102 in), 32.5 mm radial section height, C 102 kN, C0 90 kN, Pu 3.55 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 1850 g. Load balance: C0 90 kN against C 102 kN gives a 0.88 ratio, typical of a steep-angle axial-oriented design; Pu 3.55 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 85 mm bore: 102 kN C divided by the 32.5 mm radial section height gives 3.1 kN per section millimetre; the 1850 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,300 r/min against a 5,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "One 7217-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7217-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Assign interference to the rotating ring — roughly k5 on a 85 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7217-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7217-BECBP?",
        "a": "7217 BECBP measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 1850 g. SKF 17000 ratings: C 102 kN, C0 90 kN, Pu 3.55 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7217-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 85 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-217-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (102/90 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-217-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (102/90 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7217 BEP is the basic 85×150×28 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217-BECBP",
      "7217 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7217 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 102,
    "static_load_kN": 90,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7217 BECBY is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 85×150×28 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 85×150×28 mm (3.346×5.906×1.102 in), 32.5 mm radial section height, C 102 kN, C0 90 kN, Pu 3.55 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 1850 g. The 3.55 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 102/90 kN ratings and 1850 g mass this execution carries about 1.20 kN of C per millimetre of bore. Sizing arithmetic on the 85 mm bore: 102 kN C divided by the 32.5 mm radial section height gives 3.1 kN per section millimetre; the 1850 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,300 r/min against a 5,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7217-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7217-BECBY?",
        "a": "7217 BECBY measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 1850 g. SKF 17000 ratings: C 102 kN, C0 90 kN, Pu 3.55 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7217-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 5,300 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7217-BECBY?",
        "a": "The 5,300 r/min reference (thermal) and 5,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-217-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (102/90 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-217-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (102/90 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7217 BEP is the basic 85×150×28 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217-BECBY",
      "7217 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7217-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7217 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 102,
    "static_load_kN": 90,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7217 BECBM is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 85×150×28 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 85×150×28 mm (3.346×5.906×1.102 in), 32.5 mm radial section height, C 102 kN, C0 90 kN, Pu 3.55 kN.reference speed 5,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1850 g. At the printed limiting speed of 6,700 r/min the mean pitch diameter dm ≈ 117.5 mm implies a dn value around 787k mm·r/min; the 5,300 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 28 mm width over a 32.5 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 1850 g for 102 kN of dynamic capacity — about 18 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 5,300 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 0.79. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 28 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly k5 on a 85 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "At 85 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7217-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7217-BECBM?",
        "a": "7217 BECBM measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 1850 g. SKF 17000 ratings: C 102 kN, C0 90 kN, Pu 3.55 kN, reference speed 5,300 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7217-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; 7217 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-217-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (102/90 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-217-MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (102/90 kN vs 156/173 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7217 BEP is the basic 85×150×28 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7217-BECBM",
      "7217 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7317 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 146,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 BEP is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 146 kN, C0 122 kN, Pu 4.5 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 4450 g. At the printed limiting speed of 4,300 r/min the mean pitch diameter dm ≈ 132.5 mm implies a dn value around 570k mm·r/min; the 4,500 r/min reference speed is the thermal-planning figure under catalogue load. The 4.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 146/122 kN ratings and 4450 g mass this execution carries about 1.72 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 4,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.05. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 85 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7317-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7317 BEP as the single basic pa66 execution; the other order numbers of the 7317 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7317-BEP?",
        "a": "7317 BEP measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 4450 g. SKF 17000 ratings: C 146 kN, C0 122 kN, Pu 4.5 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7317-BEP?",
        "a": "The 4,500 r/min reference (thermal) and 4,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7317-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (146/122 kN vs 250/255 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7317 BEP is the basic 85×180×41 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317-BEP",
      "7317 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-BEM",
    "brand": "SKF",
    "manufacturer_designation": "7317 BEM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 146,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.5,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 BEM is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 146 kN, C0 122 kN, Pu 4.5 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,500 r/min (mechanical), which coincide for this size, catalogue mass 4450 g. Sizing arithmetic on the 85 mm bore: 146 kN C divided by the 47.5 mm radial section height gives 3.1 kN per section millimetre; the 4450 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 4.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 146/122 kN ratings and 4450 g mass this execution carries about 1.72 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 85 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7317-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7317 BEM as the single basic machined brass execution; the other order numbers of the 7317 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7317-BEM?",
        "a": "7317 BEM measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 4450 g. SKF 17000 ratings: C 146 kN, C0 122 kN, Pu 4.5 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,500 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7317-BEM?",
        "a": "With a rotating inner ring use roughly k5 on the 85 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (146/122 kN vs 250/255 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7317 BEP is the basic 85×180×41 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317-BEM",
      "7317 BEM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7317 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 156,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 BECBP is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 156 kN, C0 132 kN, Pu 4.9 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 4450 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 4,500 r/min reference; at dm ≈ 132.5 mm the corresponding dn is approximately 636k mm·r/min. Selection figures for 7317 BECBP: the static-to-dynamic ratio C0/C is 0.85, Pu 4.9 kN is about 3 % of C, and catalogue mass works out to roughly 52 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 4,800 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7317-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7317-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7317-BECBP?",
        "a": "7317 BECBP measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 4450 g. SKF 17000 ratings: C 156 kN, C0 132 kN, Pu 4.9 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7317-BECBP?",
        "a": "The 4,500 r/min reference (thermal) and 4,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7317-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (156/132 kN vs 250/255 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7317 BEP is the basic 85×180×41 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317-BECBP",
      "7317 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7317 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 BECBY is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 156 kN, C0 132 kN, Pu 4.9 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 4450 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 4,500 r/min reference; at dm ≈ 132.5 mm the corresponding dn is approximately 636k mm·r/min. Sizing arithmetic on the 85 mm bore: 156 kN C divided by the 47.5 mm radial section height gives 3.3 kN per section millimetre; the 4450 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 4,800 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7317-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7317-BECBY?",
        "a": "7317 BECBY measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 4450 g. SKF 17000 ratings: C 156 kN, C0 132 kN, Pu 4.9 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7317-BECBY?",
        "a": "The 4,500 r/min reference (thermal) and 4,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7317-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (156/132 kN vs 250/255 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7317 BEP is the basic 85×180×41 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317-BECBY",
      "7317 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7317 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 156,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 BEGAPH is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 156 kN, C0 132 kN, Pu 4.9 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 4450 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 4,500 r/min reference; at dm ≈ 132.5 mm the corresponding dn is approximately 636k mm·r/min. At the printed limiting speed of 4,800 r/min the mean pitch diameter dm ≈ 132.5 mm implies a dn value around 636k mm·r/min; the 4,500 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 4,800 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "One 7317-BEGAPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEGAPH establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly k5 on a 85 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7317-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7317-BEGAPH?",
        "a": "7317 BEGAPH measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 4450 g. SKF 17000 ratings: C 156 kN, C0 132 kN, Pu 4.9 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7317-BEGAPH?",
        "a": "The 4,500 r/min reference (thermal) and 4,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7317-BEGAPH take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (156/132 kN vs 250/255 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7317 BEP is the basic 85×180×41 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317-BEGAPH",
      "7317 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7317-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7317 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 4450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7317 BECBM is SKF's 85 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 85×180×41 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 156 kN, C0 132 kN, Pu 4.9 kN.reference speed 4,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 4450 g. Mass and section check: 4450 g inside the 85×180×41 mm outline leaves a 47.5 mm radial section, and the 132 kN static rating is 0.85× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 4.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 156/132 kN ratings and 4450 g mass this execution carries about 1.84 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 6,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.75. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 41 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7317-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7317-BECBM?",
        "a": "7317 BECBM measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 4450 g. SKF 17000 ratings: C 156 kN, C0 132 kN, Pu 4.9 kN, reference speed 4,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7317-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7317-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×180×41 mm envelope with catalogue ratings within 10 %; 7317 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-317-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (156/132 kN vs 250/255 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7317 BEP is the basic 85×180×41 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7317-BECBM",
      "7317 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7218 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 108,
    "static_load_kN": 96.5,
    "fatigue_load_limit_kN": 3.65,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7218 BEP is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 90×160×30 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 90×160×30 mm (3.543×6.299×1.181 in), 35.0 mm radial section height, C 108 kN, C0 96.5 kN, Pu 3.65 kN.reference speed 5,000 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 2300 g. Selection figures for 7218 BEP: the static-to-dynamic ratio C0/C is 0.89, Pu 3.65 kN is about 3 % of C, and catalogue mass works out to roughly 26 g per millimetre of bore. Load balance: C0 96.5 kN against C 108 kN gives a 0.89 ratio, typical of a steep-angle axial-oriented design; Pu 3.65 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 160 over bore 90 is a 1.78× step for this size, and the 30 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 90 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7218-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7218 BEP as the single basic pa66 execution; the other order numbers of the 7218 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7218-BEP?",
        "a": "7218 BEP measures 90 mm bore × 160 mm OD × 30 mm width (3.543 × 6.299 × 1.181 in), mass about 2300 g. SKF 17000 ratings: C 108 kN, C0 96.5 kN, Pu 3.65 kN, reference speed 5,000 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which fits should I use for 7218-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 90 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7218-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,500 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-218-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (108/96.5 kN vs 186/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7218 BEP is the basic 90×160×30 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218-BEP",
      "7218 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7218 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 116,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7218 BECBP is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 90×160×30 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 90×160×30 mm (3.543×6.299×1.181 in), 35.0 mm radial section height, C 116 kN, C0 104 kN, Pu 4 kN.reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size, catalogue mass 2300 g. Envelope economics: the 30 mm width over a 35.0 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 2300 g for 116 kN of dynamic capacity — about 20 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,000 r/min while thermal balance under catalogue load sets the 5,000 r/min reference; at dm ≈ 125.0 mm the corresponding dn is approximately 625k mm·r/min. Bore-to-OD planning: OD 160 over bore 90 is a 1.78× step for this size, and the 30 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 90 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 30 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7218-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7218-BECBP?",
        "a": "7218 BECBP measures 90 mm bore × 160 mm OD × 30 mm width (3.543 × 6.299 × 1.181 in), mass about 2300 g. SKF 17000 ratings: C 116 kN, C0 104 kN, Pu 4 kN, reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7218-BECBP?",
        "a": "The 5,000 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7218-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-218-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (116/104 kN vs 186/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7218 BEP is the basic 90×160×30 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218-BECBP",
      "7218 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7218 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 116,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7218 BECBY is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 90×160×30 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 90×160×30 mm (3.543×6.299×1.181 in), 35.0 mm radial section height, C 116 kN, C0 104 kN, Pu 4 kN.reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size, catalogue mass 2300 g. Envelope economics: the 30 mm width over a 35.0 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 2300 g for 116 kN of dynamic capacity — about 20 g per rated kN. Mass and section check: 2300 g inside the 90×160×30 mm outline leaves a 35.0 mm radial section, and the 104 kN static rating is 0.90× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 160 over bore 90 is a 1.78× step for this size, and the 30 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 90 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 90 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7218-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7218-BECBY?",
        "a": "7218 BECBY measures 90 mm bore × 160 mm OD × 30 mm width (3.543 × 6.299 × 1.181 in), mass about 2300 g. SKF 17000 ratings: C 116 kN, C0 104 kN, Pu 4 kN, reference speed 5,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7218-BECBY?",
        "a": "The 5,000 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7218-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-218-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (116/104 kN vs 186/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7218 BEP is the basic 90×160×30 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218-BECBY",
      "7218 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7218-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7218 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 116,
    "static_load_kN": 104,
    "fatigue_load_limit_kN": 4,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 2300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7218 BECBM is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 90×160×30 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 90×160×30 mm (3.543×6.299×1.181 in), 35.0 mm radial section height, C 116 kN, C0 104 kN, Pu 4 kN.reference speed 5,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 2300 g. The 4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 116/104 kN ratings and 2300 g mass this execution carries about 1.29 kN of C per millimetre of bore. Load balance: C0 104 kN against C 116 kN gives a 0.90 ratio, typical of a steep-angle axial-oriented design; Pu 4 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 160 over bore 90 is a 1.78× step for this size, and the 30 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 90 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7218-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7218-BECBM?",
        "a": "7218 BECBM measures 90 mm bore × 160 mm OD × 30 mm width (3.543 × 6.299 × 1.181 in), mass about 2300 g. SKF 17000 ratings: C 116 kN, C0 104 kN, Pu 4 kN, reference speed 5,000 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7218-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 6,300 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7218-BECBM?",
        "a": "The 5,000 r/min reference (thermal) and 6,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7218-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7218-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×160×30 mm envelope with catalogue ratings within 10 %; 7218 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-218-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (116/104 kN vs 186/200 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7218 BEP is the basic 90×160×30 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7218-BECBM",
      "7218 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7318 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 156,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.8,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 5200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7318 BEP is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 156 kN, C0 134 kN, Pu 4.8 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 5200 g. Mass and section check: 5200 g inside the 90×190×43 mm outline leaves a 50.0 mm radial section, and the 134 kN static rating is 0.86× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 134 kN against C 156 kN gives a 0.86 ratio, typical of a steep-angle axial-oriented design; Pu 4.8 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7318-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7318 BEP as the single basic pa66 execution; the other order numbers of the 7318 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7318-BEP?",
        "a": "7318 BEP measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5200 g. SKF 17000 ratings: C 156 kN, C0 134 kN, Pu 4.8 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Can one 7318-BEP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7318-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (156/134 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (156/134 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7318 BEP is the basic 90×190×43 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318-BEP",
      "7318 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-BEM",
    "brand": "SKF",
    "manufacturer_designation": "7318 BEM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.8,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 5200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7318 BEM is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 156 kN, C0 134 kN, Pu 4.8 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,300 r/min (mechanical), which coincide for this size, catalogue mass 5200 g. Selection figures for 7318 BEM: the static-to-dynamic ratio C0/C is 0.86, Pu 4.8 kN is about 3 % of C, and catalogue mass works out to roughly 58 g per millimetre of bore. Load balance: C0 134 kN against C 156 kN gives a 0.86 ratio, typical of a steep-angle axial-oriented design; Pu 4.8 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BEM unit is ground for arbitrary pairing, a basic execution is not.",
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "At 90 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7318-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7318 BEM as the single basic machined brass execution; the other order numbers of the 7318 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7318-BEM?",
        "a": "7318 BEM measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5200 g. SKF 17000 ratings: C 156 kN, C0 134 kN, Pu 4.8 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.."
      },
      {
        "q": "Which fits should I use for 7318-BEM?",
        "a": "With a rotating inner ring use roughly k5 on the 90 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7318-BEM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (156/134 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (156/134 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7318 BEP is the basic 90×190×43 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318-BEM",
      "7318 BEM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7318 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 166,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 5200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7318 BECBP is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 166 kN, C0 146 kN, Pu 5.3 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 5200 g. Sizing arithmetic on the 90 mm bore: 166 kN C divided by the 50.0 mm radial section height gives 3.3 kN per section millimetre; the 5200 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 5200 g inside the 90×190×43 mm outline leaves a 50.0 mm radial section, and the 146 kN static rating is 0.88× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7318-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Fillet radii must clear the chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7318-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7318-BECBP?",
        "a": "7318 BECBP measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5200 g. SKF 17000 ratings: C 166 kN, C0 146 kN, Pu 5.3 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7318-BECBP?",
        "a": "With a rotating inner ring use roughly k5 on the 90 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7318 BEP is the basic 90×190×43 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318-BECBP",
      "7318 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7318 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 166,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 5200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7318 BECBY is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 166 kN, C0 146 kN, Pu 5.3 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 5200 g. Load balance: C0 146 kN against C 166 kN gives a 0.88 ratio, typical of a steep-angle axial-oriented design; Pu 5.3 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 5200 g inside the 90×190×43 mm outline leaves a 50.0 mm radial section, and the 146 kN static rating is 0.88× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "One 7318-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 90 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 43 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7318-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7318-BECBY?",
        "a": "7318 BECBY measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5200 g. SKF 17000 ratings: C 166 kN, C0 146 kN, Pu 5.3 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7318-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,500 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7318-BECBY?",
        "a": "The 4,300 r/min reference (thermal) and 4,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7318 BEP is the basic 90×190×43 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318-BECBY",
      "7318 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7318 BEGAPH",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 166,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 5200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7318 BEGAPH is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 166 kN, C0 146 kN, Pu 5.3 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 5200 g. Mass and section check: 5200 g inside the 90×190×43 mm outline leaves a 50.0 mm radial section, and the 146 kN static rating is 0.88× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 140.0 mm implies a dn value around 630k mm·r/min; the 4,300 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "centrifuge and separator drives",
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "One 7318-BEGAPH locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7318-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7318-BEGAPH?",
        "a": "7318 BEGAPH measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5200 g. SKF 17000 ratings: C 166 kN, C0 146 kN, Pu 5.3 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "Which grease and fill for 7318-BEGAPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,500 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7318-BEGAPH?",
        "a": "The 4,300 r/min reference (thermal) and 4,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7318 BEP is the basic 90×190×43 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318-BEGAPH",
      "7318 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7318-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7318 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 166,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 5200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7318 BECBM is SKF's 90 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 90×190×43 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 166 kN, C0 146 kN, Pu 5.3 kN.reference speed 4,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 5200 g. Selection figures for 7318 BECBM: the static-to-dynamic ratio C0/C is 0.88, Pu 5.3 kN is about 3 % of C, and catalogue mass works out to roughly 58 g per millimetre of bore. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 140.0 mm implies a dn value around 784k mm·r/min; the 4,300 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7318-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly k5 on a 90 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7318-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7318-BECBM?",
        "a": "7318 BECBM measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 5200 g. SKF 17000 ratings: C 166 kN, C0 146 kN, Pu 5.3 kN, reference speed 4,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7318-BECBM?",
        "a": "The 4,300 r/min reference (thermal) and 5,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7318-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; 7318 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (166/146 kN vs 285/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7318 BEP is the basic 90×190×43 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7318-BECBM",
      "7318 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7219 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 124,
    "static_load_kN": 108,
    "fatigue_load_limit_kN": 4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7219 BEP is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 95×170×32 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 95×170×32 mm (3.74×6.693×1.26 in), 37.5 mm radial section height, C 124 kN, C0 108 kN, Pu 4 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 2700 g. Load balance: C0 108 kN against C 124 kN gives a 0.87 ratio, typical of a steep-angle axial-oriented design; Pu 4 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 2700 g inside the 95×170×32 mm outline leaves a 37.5 mm radial section, and the 108 kN static rating is 0.87× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 170 over bore 95 is a 1.79× step for this size, and the 32 mm width gives a bore/width ratio of 2.97; use these ratios when housing space around the 95 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly k5 on a 95 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7219-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7219 BEP as the single basic pa66 execution; the other order numbers of the 7219 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7219-BEP?",
        "a": "7219 BEP measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 2700 g. SKF 17000 ratings: C 124 kN, C0 108 kN, Pu 4 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7219-BEP?",
        "a": "With a rotating inner ring use roughly k5 on the 95 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-219-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (124/108 kN vs 212/232 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7219 BEP is the basic 95×170×32 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219-BEP",
      "7219 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7219 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 129,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7219 BECBP is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 95×170×32 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 95×170×32 mm (3.74×6.693×1.26 in), 37.5 mm radial section height, C 129 kN, C0 118 kN, Pu 4.4 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 2700 g. The 4.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 129/118 kN ratings and 2700 g mass this execution carries about 1.36 kN of C per millimetre of bore. Load balance: C0 118 kN against C 129 kN gives a 0.91 ratio, typical of a steep-angle axial-oriented design; Pu 4.4 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 170 over bore 95 is a 1.79× step for this size, and the 32 mm width gives a bore/width ratio of 2.97; use these ratios when housing space around the 95 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7219-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "At 95 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7219-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 32 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7219-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7219-BECBP?",
        "a": "7219 BECBP measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 2700 g. SKF 17000 ratings: C 129 kN, C0 118 kN, Pu 4.4 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7219-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,800 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7219-BECBP?",
        "a": "The 4,500 r/min reference (thermal) and 4,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-219-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (129/118 kN vs 212/232 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7219 BEP is the basic 95×170×32 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219-BECBP",
      "7219 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7219 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 129,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7219 BECBY is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 95×170×32 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 95×170×32 mm (3.74×6.693×1.26 in), 37.5 mm radial section height, C 129 kN, C0 118 kN, Pu 4.4 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 2700 g. Mass and section check: 2700 g inside the 95×170×32 mm outline leaves a 37.5 mm radial section, and the 118 kN static rating is 0.91× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 118 kN against C 129 kN gives a 0.91 ratio, typical of a steep-angle axial-oriented design; Pu 4.4 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 170 over bore 95 is a 1.79× step for this size, and the 32 mm width gives a bore/width ratio of 2.97; use these ratios when housing space around the 95 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 95 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7219-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7219-BECBY?",
        "a": "7219 BECBY measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 2700 g. SKF 17000 ratings: C 129 kN, C0 118 kN, Pu 4.4 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which grease and fill for 7219-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,800 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7219-BECBY?",
        "a": "The 4,500 r/min reference (thermal) and 4,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-219-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (129/118 kN vs 212/232 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7219 BEP is the basic 95×170×32 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219-BECBY",
      "7219 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219-BEGAPH",
    "brand": "SKF",
    "manufacturer_designation": "7219 BEGAPH",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 129,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7219 BEGAPH is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 95×170×32 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage. Envelope 95×170×32 mm (3.74×6.693×1.26 in), 37.5 mm radial section height, C 129 kN, C0 118 kN, Pu 4.4 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 2700 g. Load balance: C0 118 kN against C 129 kN gives a 0.91 ratio, typical of a steep-angle axial-oriented design; Pu 4.4 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,800 r/min while thermal balance under catalogue load sets the 4,500 r/min reference; at dm ≈ 132.5 mm the corresponding dn is approximately 636k mm·r/min. Bore-to-OD planning: OD 170 over bore 95 is a 1.79× step for this size, and the 32 mm width gives a bore/width ratio of 2.97; use these ratios when housing space around the 95 mm shaft is the first constraint. Preload and cage note: BEGAPH arrives as a universally matchable unit with GA light preload already defined for back-to-back or face-to-face sets, combined with the glass-fibre PEEK ball-centred cage for high-speed duty; it replaces field preload adjustment, not the need for correct stand-off geometry.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PEEK cage wear plus preload drift when contaminated lubricant reaches the ball-centred pockets of a GA set",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "At 95 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7219-BEGAPH favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BEGAPH bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7219-BEGAPH?",
        "a": "7219 BEGAPH measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 2700 g. SKF 17000 ratings: C 129 kN, C0 118 kN, Pu 4.4 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the BEGAPH suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PEEK cage, ball-centred (suffix PH), keeping the polymer-cage speed advantage well above the PA66 temperature range. GA marks universal matching with light factory preload for back-to-back or face-to-face sets — stiffer than CB clearance while generating less heat than GB/GC. BEGAPH combines light-preload (GA) universal matching with a PEEK ball-centred cage."
      },
      {
        "q": "Which grease and fill for 7219-BEGAPH?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,800 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7219-BEGAPH?",
        "a": "The 4,500 r/min reference (thermal) and 4,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-219-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (129/118 kN vs 212/232 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7219 BEP is the basic 95×170×32 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219-BEGAPH",
      "7219 BEGAPH"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7219-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7219 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 129,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7219 BECBM is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 95×170×32 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 95×170×32 mm (3.74×6.693×1.26 in), 37.5 mm radial section height, C 129 kN, C0 118 kN, Pu 4.4 kN.reference speed 4,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 2700 g. Envelope economics: the 32 mm width over a 37.5 mm section yields 0.85 mm of ring width per section millimetre, and the bearing weighs 2700 g for 129 kN of dynamic capacity — about 21 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 6,000 r/min while thermal balance under catalogue load sets the 4,500 r/min reference; at dm ≈ 132.5 mm the corresponding dn is approximately 795k mm·r/min. Bore-to-OD planning: OD 170 over bore 95 is a 1.79× step for this size, and the 32 mm width gives a bore/width ratio of 2.97; use these ratios when housing space around the 95 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7219-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 95 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7219-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7219-BECBM?",
        "a": "7219 BECBM measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 2700 g. SKF 17000 ratings: C 129 kN, C0 118 kN, Pu 4.4 kN, reference speed 4,500 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7219-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 95 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7219-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 6,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×170×32 mm envelope with catalogue ratings within 10 %; 7219 BEGAPH is the PEEK cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-219-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (129/118 kN vs 212/232 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7219 BEP is the basic 95×170×32 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7219-BECBM",
      "7219 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7319 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 168,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 6050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7319 BEP is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 95×200×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 168 kN, C0 150 kN, Pu 5.2 kN.reference speed 4,000 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 6050 g. Envelope economics: the 45 mm width over a 52.5 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 6050 g for 168 kN of dynamic capacity — about 36 g per rated kN. Mass and section check: 6050 g inside the 95×200×45 mm outline leaves a 52.5 mm radial section, and the 150 kN static rating is 0.89× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7319-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Assign interference to the rotating ring — roughly k5 on a 95 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "One 7319-BEP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7319-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7319 BEP as the single basic pa66 execution; the other order numbers of the 7319 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7319-BEP?",
        "a": "7319 BEP measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 6050 g. SKF 17000 ratings: C 168 kN, C0 150 kN, Pu 5.2 kN, reference speed 4,000 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7319-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (168/150 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (168/150 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7319 BEP is the basic 95×200×45 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319-BEP",
      "7319 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319-BEM",
    "brand": "SKF",
    "manufacturer_designation": "7319 BEM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 168,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 6050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7319 BEM is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 95×200×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 168 kN, C0 150 kN, Pu 5.2 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size, catalogue mass 6050 g. Load balance: C0 150 kN against C 168 kN gives a 0.89 ratio, typical of a steep-angle axial-oriented design; Pu 5.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 6050 g inside the 95×200×45 mm outline leaves a 52.5 mm radial section, and the 150 kN static rating is 0.89× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "One 7319-BEM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7319-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7319 BEM as the single basic machined brass execution; the other order numbers of the 7319 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7319-BEM?",
        "a": "7319 BEM measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 6050 g. SKF 17000 ratings: C 168 kN, C0 150 kN, Pu 5.2 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.."
      },
      {
        "q": "Can one 7319-BEM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7319-BEM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (168/150 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (168/150 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7319 BEP is the basic 95×200×45 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319-BEM",
      "7319 BEM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7319 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 180,
    "static_load_kN": 163,
    "fatigue_load_limit_kN": 5.7,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 6050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7319 BECBP is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 95×200×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 180 kN, C0 163 kN, Pu 5.7 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 6050 g. Selection figures for 7319 BECBP: the static-to-dynamic ratio C0/C is 0.91, Pu 5.7 kN is about 3 % of C, and catalogue mass works out to roughly 64 g per millimetre of bore. At the printed limiting speed of 4,300 r/min the mean pitch diameter dm ≈ 147.5 mm implies a dn value around 634k mm·r/min; the 4,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7319-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7319-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7319-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7319-BECBP?",
        "a": "7319 BECBP measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 6050 g. SKF 17000 ratings: C 180 kN, C0 163 kN, Pu 5.7 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7319-BECBP?",
        "a": "The 4,000 r/min reference (thermal) and 4,300 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7319-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (180/163 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (180/163 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7319 BEP is the basic 95×200×45 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319-BECBP",
      "7319 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7319 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 180,
    "static_load_kN": 163,
    "fatigue_load_limit_kN": 5.7,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 6050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7319 BECBY is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 95×200×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 180 kN, C0 163 kN, Pu 5.7 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 6050 g. Selection figures for 7319 BECBY: the static-to-dynamic ratio C0/C is 0.91, Pu 5.7 kN is about 3 % of C, and catalogue mass works out to roughly 64 g per millimetre of bore. Load balance: C0 163 kN against C 180 kN gives a 0.91 ratio, typical of a steep-angle axial-oriented design; Pu 5.7 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "At 95 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7319-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7319-BECBY?",
        "a": "7319 BECBY measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 6050 g. SKF 17000 ratings: C 180 kN, C0 163 kN, Pu 5.7 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Which fits should I use for 7319-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 95 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7319-BECBY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (180/163 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (180/163 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7319 BEP is the basic 95×200×45 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319-BECBY",
      "7319 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7319-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7319 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 180,
    "static_load_kN": 163,
    "fatigue_load_limit_kN": 5.7,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 6050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7319 BECBM is SKF's 95 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 95×200×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 180 kN, C0 163 kN, Pu 5.7 kN.reference speed 4,000 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 6050 g. Sizing arithmetic on the 95 mm bore: 180 kN C divided by the 52.5 mm radial section height gives 3.4 kN per section millimetre; the 6050 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 6050 g inside the 95×200×45 mm outline leaves a 52.5 mm radial section, and the 163 kN static rating is 0.91× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Assign interference to the rotating ring — roughly k5 on a 95 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7319-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7319-BECBM?",
        "a": "7319 BECBM measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 6050 g. SKF 17000 ratings: C 180 kN, C0 163 kN, Pu 5.7 kN, reference speed 4,000 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7319-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 95 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; 7319 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (180/163 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (180/163 kN vs 305/340 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7319 BEP is the basic 95×200×45 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7319-BECBM",
      "7319 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7220 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 135,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 3300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7220 BEP is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 100×180×34 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 100×180×34 mm (3.937×7.087×1.339 in), 40.0 mm radial section height, C 135 kN, C0 122 kN, Pu 4.4 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 3300 g. Load balance: C0 122 kN against C 135 kN gives a 0.90 ratio, typical of a steep-angle axial-oriented design; Pu 4.4 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min while thermal balance under catalogue load sets the 4,300 r/min reference; at dm ≈ 140.0 mm the corresponding dn is approximately 560k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 4,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.07. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly k5 on a 100 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "At 100 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 34 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7220-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7220-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7220 BEP as the single basic pa66 execution; the other order numbers of the 7220 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7220-BEP?",
        "a": "7220 BEP measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 3300 g. SKF 17000 ratings: C 135 kN, C0 122 kN, Pu 4.4 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7220-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7220-BEP?",
        "a": "The 4,300 r/min reference (thermal) and 4,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-220-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (135/122 kN vs 236/265 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7220 BEP is the basic 100×180×34 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220-BEP",
      "7220 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7220 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 143,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.75,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 3300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7220 BECBP is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 100×180×34 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 100×180×34 mm (3.937×7.087×1.339 in), 40.0 mm radial section height, C 143 kN, C0 134 kN, Pu 4.75 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 3300 g. The 4.75 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 143/134 kN ratings and 3300 g mass this execution carries about 1.43 kN of C per millimetre of bore. Mass and section check: 3300 g inside the 100×180×34 mm outline leaves a 40.0 mm radial section, and the 134 kN static rating is 0.94× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.96. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "One 7220-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 34 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7220-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7220-BECBP?",
        "a": "7220 BECBP measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 3300 g. SKF 17000 ratings: C 143 kN, C0 134 kN, Pu 4.75 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7220-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,500 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7220-BECBP?",
        "a": "The 4,300 r/min reference (thermal) and 4,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-220-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (143/134 kN vs 236/265 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7220 BEP is the basic 100×180×34 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220-BECBP",
      "7220 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7220 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 143,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.75,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 3300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7220 BECBY is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 100×180×34 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 100×180×34 mm (3.937×7.087×1.339 in), 40.0 mm radial section height, C 143 kN, C0 134 kN, Pu 4.75 kN.reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 3300 g. Mass and section check: 3300 g inside the 100×180×34 mm outline leaves a 40.0 mm radial section, and the 134 kN static rating is 0.94× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 140.0 mm implies a dn value around 630k mm·r/min; the 4,300 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 0.96. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7220-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7220-BECBY?",
        "a": "7220 BECBY measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 3300 g. SKF 17000 ratings: C 143 kN, C0 134 kN, Pu 4.75 kN, reference speed 4,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7220-BECBY?",
        "a": "With a rotating inner ring use roughly k5 on the 100 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-220-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (143/134 kN vs 236/265 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7220 BEP is the basic 100×180×34 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220-BECBY",
      "7220 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7220-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7220 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 143,
    "static_load_kN": 134,
    "fatigue_load_limit_kN": 4.75,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 3300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7220 BECBM is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 100×180×34 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 100×180×34 mm (3.937×7.087×1.339 in), 40.0 mm radial section height, C 143 kN, C0 134 kN, Pu 4.75 kN.reference speed 4,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 3300 g. Envelope economics: the 34 mm width over a 40.0 mm section yields 0.85 mm of ring width per section millimetre, and the bearing weighs 3300 g for 143 kN of dynamic capacity — about 23 g per rated kN. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 140.0 mm implies a dn value around 784k mm·r/min; the 4,300 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 0.77. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "One 7220-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7220-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7220-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7220-BECBM?",
        "a": "7220 BECBM measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 3300 g. SKF 17000 ratings: C 143 kN, C0 134 kN, Pu 4.75 kN, reference speed 4,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7220-BECBM?",
        "a": "With a rotating inner ring use roughly k5 on the 100 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7220-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 5,600 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7220-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7220-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×180×34 mm envelope with catalogue ratings within 10 %; 7220 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-220-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (143/134 kN vs 236/265 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7220 BEP is the basic 100×180×34 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7220-BECBM",
      "7220 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320-BEM",
    "brand": "SKF",
    "manufacturer_designation": "7320 BEM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 203,
    "static_load_kN": 190,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 7500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7320 BEM is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 203 kN, C0 190 kN, Pu 6.4 kN.reference speed 3,800 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 7500 g. Load balance: C0 190 kN against C 203 kN gives a 0.94 ratio, typical of a steep-angle axial-oriented design; Pu 6.4 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,600 r/min while thermal balance under catalogue load sets the 3,800 r/min reference; at dm ≈ 157.5 mm the corresponding dn is approximately 567k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 3,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 47 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BEM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7320-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7320 BEM as the single basic machined brass execution; the other order numbers of the 7320 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7320-BEM?",
        "a": "7320 BEM measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 7500 g. SKF 17000 ratings: C 203 kN, C0 190 kN, Pu 6.4 kN, reference speed 3,800 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BEM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.."
      },
      {
        "q": "Which grease and fill for 7320-BEM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,600 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7320-BEM?",
        "a": "The 3,800 r/min reference (thermal) and 3,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-320-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (203/190 kN vs 345/400 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7320 BEP is the basic 100×215×47 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320-BEM",
      "7320 BEM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7320 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 203,
    "static_load_kN": 190,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 7500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7320 BEP is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 203 kN, C0 190 kN, Pu 6.4 kN.reference speed 3,800 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 7500 g. Envelope economics: the 47 mm width over a 57.5 mm section yields 0.82 mm of ring width per section millimetre, and the bearing weighs 7500 g for 203 kN of dynamic capacity — about 37 g per rated kN. Selection figures for 7320 BEP: the static-to-dynamic ratio C0/C is 0.94, Pu 6.4 kN is about 3 % of C, and catalogue mass works out to roughly 75 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 3,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7320-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7320-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7320 BEP as the single basic pa66 execution; the other order numbers of the 7320 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7320-BEP?",
        "a": "7320 BEP measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 7500 g. SKF 17000 ratings: C 203 kN, C0 190 kN, Pu 6.4 kN, reference speed 3,800 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What minimum axial load does 7320-BEP need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-320-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (203/190 kN vs 345/400 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7320 BEP is the basic 100×215×47 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320-BEP",
      "7320 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7320 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 216,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 7500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7320 BECBP is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 216 kN, C0 208 kN, Pu 6.95 kN.reference speed 3,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 7500 g. Selection figures for 7320 BECBP: the static-to-dynamic ratio C0/C is 0.96, Pu 6.95 kN is about 3 % of C, and catalogue mass works out to roughly 75 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min while thermal balance under catalogue load sets the 3,800 r/min reference; at dm ≈ 157.5 mm the corresponding dn is approximately 630k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 4,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 47 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7320-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7320-BECBP?",
        "a": "7320 BECBP measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 7500 g. SKF 17000 ratings: C 216 kN, C0 208 kN, Pu 6.95 kN, reference speed 3,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7320-BECBP?",
        "a": "The 3,800 r/min reference (thermal) and 4,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7320-BECBP take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-320-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (216/208 kN vs 345/400 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7320 BEP is the basic 100×215×47 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320-BECBP",
      "7320 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7320 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 216,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 7500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7320 BECBY is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 216 kN, C0 208 kN, Pu 6.95 kN.reference speed 3,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 7500 g. Selection figures for 7320 BECBY: the static-to-dynamic ratio C0/C is 0.96, Pu 6.95 kN is about 3 % of C, and catalogue mass works out to roughly 75 g per millimetre of bore. Envelope economics: the 47 mm width over a 57.5 mm section yields 0.82 mm of ring width per section millimetre, and the bearing weighs 7500 g for 216 kN of dynamic capacity — about 35 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 4,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Assign interference to the rotating ring — roughly k5 on a 100 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "One 7320-BECBY locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7320-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7320-BECBY?",
        "a": "7320 BECBY measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 7500 g. SKF 17000 ratings: C 216 kN, C0 208 kN, Pu 6.95 kN, reference speed 3,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What minimum axial load does 7320-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-320-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (216/208 kN vs 345/400 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7320 BEP is the basic 100×215×47 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320-BECBY",
      "7320 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7320-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7320 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 216,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 7500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7320 BECBM is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 216 kN, C0 208 kN, Pu 6.95 kN.reference speed 3,800 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 7500 g. Sizing arithmetic on the 100 mm bore: 216 kN C divided by the 57.5 mm radial section height gives 3.8 kN per section millimetre; the 7500 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 208 kN against C 216 kN gives a 0.96 ratio, typical of a steep-angle axial-oriented design; Pu 6.95 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 5,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.76. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7320-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7320-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7320-BECBM?",
        "a": "7320 BECBM measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 7500 g. SKF 17000 ratings: C 216 kN, C0 208 kN, Pu 6.95 kN, reference speed 3,800 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7320-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7320-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 100×215×47 mm envelope with catalogue ratings within 10 %; 7320 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-320-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (216/208 kN vs 345/400 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7320 BEP is the basic 100×215×47 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7320-BECBM",
      "7320 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7221-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7221 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 156,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 3950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7221 BECBP is SKF's 105 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 105×190×36 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 105×190×36 mm (4.134×7.48×1.417 in), 42.5 mm radial section height, C 156 kN, C0 150 kN, Pu 5.2 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 3950 g. Envelope economics: the 36 mm width over a 42.5 mm section yields 0.85 mm of ring width per section millimetre, and the bearing weighs 3950 g for 156 kN of dynamic capacity — about 25 g per rated kN. At the printed limiting speed of 4,300 r/min the mean pitch diameter dm ≈ 147.5 mm implies a dn value around 634k mm·r/min; the 4,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 4,000 r/min against a 4,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.93. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "At 105 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C — the PA66 cage sets the ceiling, not the steel; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7221-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7221-BECBP?",
        "a": "7221 BECBP measures 105 mm bore × 190 mm OD × 36 mm width (4.134 × 7.48 × 1.417 in), mass about 3950 g. SKF 17000 ratings: C 156 kN, C0 150 kN, Pu 5.2 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7221-BECBP?",
        "a": "With a rotating inner ring use roughly m6 on the 105 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7221-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,300 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7221-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7221-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×190×36 mm envelope with catalogue ratings within 10 %; 7221 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7221",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7221 BECBP is the basic 105×190×36 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7221-BECBP",
      "7221 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7221-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7221 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 190,
    "B_mm": 36,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 150,
    "fatigue_load_limit_kN": 5.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 3950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7221 BECBM is SKF's 105 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 105×190×36 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 105×190×36 mm (4.134×7.48×1.417 in), 42.5 mm radial section height, C 156 kN, C0 150 kN, Pu 5.2 kN.reference speed 4,000 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 3950 g. The 5.2 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 156/150 kN ratings and 3950 g mass this execution carries about 1.49 kN of C per millimetre of bore. Mass and section check: 3950 g inside the 105×190×36 mm outline leaves a 42.5 mm radial section, and the 150 kN static rating is 0.96× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 4,000 r/min against a 5,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.75. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly m6 on a 105 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7221-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7221-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7221-BECBM?",
        "a": "7221 BECBM measures 105 mm bore × 190 mm OD × 36 mm width (4.134 × 7.48 × 1.417 in), mass about 3950 g. SKF 17000 ratings: C 156 kN, C0 150 kN, Pu 5.2 kN, reference speed 4,000 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7221-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7221-BECBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7221-NTN",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7221-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×190×36 mm envelope with catalogue ratings within 10 %; 7221 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7221",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7221 BECBP is the basic 105×190×36 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7221-BECBM",
      "7221 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7321-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7321 BEP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 203,
    "static_load_kN": 193,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 8550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7321 BEP is SKF's 105 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 105×225×49 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 105×225×49 mm (4.134×8.858×1.929 in), 60.0 mm radial section height, C 203 kN, C0 193 kN, Pu 6.4 kN.reference speed 3,600 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 8550 g. Mass and section check: 8550 g inside the 105×225×49 mm outline leaves a 60.0 mm radial section, and the 193 kN static rating is 0.95× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 3,400 r/min the mean pitch diameter dm ≈ 165.0 mm implies a dn value around 561k mm·r/min; the 3,600 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 3,400 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7321-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7321 BEP as the single basic pa66 execution; the other order numbers of the 7321 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7321-BEP?",
        "a": "7321 BEP measures 105 mm bore × 225 mm OD × 49 mm width (4.134 × 8.858 × 1.929 in), mass about 8550 g. SKF 17000 ratings: C 203 kN, C0 193 kN, Pu 6.4 kN, reference speed 3,600 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "Which grease and fill for 7321-BEP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 3,400 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7321-BEP?",
        "a": "The 3,600 r/min reference (thermal) and 3,400 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7321-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7321-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×225×49 mm envelope with catalogue ratings within 10 %; 7321 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7321-DECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×225×49 mm envelope with catalogue ratings within 10 %; 7321 DECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7321",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7321 BEP is the basic 105×225×49 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7321-BEP",
      "7321 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7321-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7321 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 216,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 8550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7321 BECBP is SKF's 105 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 105×225×49 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 105×225×49 mm (4.134×8.858×1.929 in), 60.0 mm radial section height, C 216 kN, C0 208 kN, Pu 6.95 kN.reference speed 3,600 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 8550 g. Sizing arithmetic on the 105 mm bore: 216 kN C divided by the 60.0 mm radial section height gives 3.6 kN per section millimetre; the 8550 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 208 kN against C 216 kN gives a 0.96 ratio, typical of a steep-angle axial-oriented design; Pu 6.95 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 3,800 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "heavy feed and take-up rolls",
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7321-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7321-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7321-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7321-BECBP?",
        "a": "7321 BECBP measures 105 mm bore × 225 mm OD × 49 mm width (4.134 × 8.858 × 1.929 in), mass about 8550 g. SKF 17000 ratings: C 216 kN, C0 208 kN, Pu 6.95 kN, reference speed 3,600 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7321-BECBP?",
        "a": "With a rotating inner ring use roughly m6 on the 105 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7321-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7321-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×225×49 mm envelope with catalogue ratings within 10 %; 7321 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7321-DECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×225×49 mm envelope with catalogue ratings within 10 %; 7321 DECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7321",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7321 BEP is the basic 105×225×49 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7321-BECBP",
      "7321 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7321-DECBM",
    "brand": "SKF",
    "manufacturer_designation": "7321 DECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 105,
    "D_mm": 225,
    "B_mm": 49,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 216,
    "static_load_kN": 208,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 8550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7321 DECBM is SKF's 105 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 105×225×49 mm to the ISO dimension plan. D marks a two-piece inner ring (split for mounting), E the optimized internal geometry, CB universal matching with Normal clearance and M the machined brass ball-centred cage. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. Envelope 105×225×49 mm (4.134×8.858×1.929 in), 60.0 mm radial section height, C 216 kN, C0 208 kN, Pu 6.95 kN.reference speed 3,600 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 8550 g. Sizing arithmetic on the 105 mm bore: 216 kN C divided by the 60.0 mm radial section height gives 3.6 kN per section millimetre; the 8550 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 49 mm width over a 60.0 mm section yields 0.82 mm of ring width per section millimetre, and the bearing weighs 8550 g for 216 kN of dynamic capacity — about 40 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 4,800 r/min limiting speed, i.e. a reference-to-limit ratio of 0.75. Split-inner-ring universal execution: the leading D means the inner ring is supplied in two halves to ease mounting and inspection of the rolling elements; E optimized internals, CB Normal-clearance set faces and the machined brass M cage complete the order number.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "split inner-ring fretting or half-ring mismatch if the two D halves are not kept matched and seated square",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7321-DECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of DECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly m6 on a 105 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7321-DECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable DECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7321-DECBM?",
        "a": "7321 DECBM measures 105 mm bore × 225 mm OD × 49 mm width (4.134 × 8.858 × 1.929 in), mass about 8550 g. SKF 17000 ratings: C 216 kN, C0 208 kN, Pu 6.95 kN, reference speed 3,600 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the DECBM suffix mean?",
        "a": "D marks a two-piece inner ring (split for mounting), E the optimized internal geometry, CB universal matching with Normal clearance and M the machined brass ball-centred cage. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7321-DECBM?",
        "a": "With a rotating inner ring use roughly m6 on the 105 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7321-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 105×225×49 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7321-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×225×49 mm envelope with catalogue ratings within 10 %; 7321 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7321-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 105×225×49 mm envelope with catalogue ratings within 10 %; 7321 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7321",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7321 BEP is the basic 105×225×49 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7321-DECBM",
      "7321 DECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222-BEP",
    "brand": "SKF",
    "manufacturer_designation": "7222 BEP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 153,
    "static_load_kN": 143,
    "fatigue_load_limit_kN": 4.9,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7222 BEP is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 110×200×38 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 110×200×38 mm (4.331×7.874×1.496 in), 45.0 mm radial section height, C 153 kN, C0 143 kN, Pu 4.9 kN.reference speed 4,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 4600 g. The 4.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 153/143 kN ratings and 4600 g mass this execution carries about 1.39 kN of C per millimetre of bore. Selection figures for 7222 BEP: the static-to-dynamic ratio C0/C is 0.93, Pu 4.9 kN is about 3 % of C, and catalogue mass works out to roughly 42 g per millimetre of bore. Bore-to-OD planning: OD 200 over bore 110 is a 1.82× step for this size, and the 38 mm width gives a bore/width ratio of 2.89; use these ratios when housing space around the 110 mm shaft is the first constraint. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.",
    "applications": [
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives",
      "printing and paper-machine rolls"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage creep or embrittlement when the non-universal single bearing is run above 120 °C",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7222-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BEP unit is ground for arbitrary pairing, a basic execution is not.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly m6 on a 110 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7222-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7222 BEP as the single basic pa66 execution; the other order numbers of the 7222 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7222-BEP?",
        "a": "7222 BEP measures 110 mm bore × 200 mm OD × 38 mm width (4.331 × 7.874 × 1.496 in), mass about 4600 g. SKF 17000 ratings: C 153 kN, C0 143 kN, Pu 4.9 kN, reference speed 4,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BEP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7222-BEP?",
        "a": "With a rotating inner ring use roughly m6 on the 110 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-222-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (153/143 kN vs 280/325 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7222 BEP is the basic 110×200×38 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222-BEP",
      "7222 BEP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7222 BECBP",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 163,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7222 BECBP is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 110×200×38 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 110×200×38 mm (4.331×7.874×1.496 in), 45.0 mm radial section height, C 163 kN, C0 156 kN, Pu 5.3 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size, catalogue mass 4600 g. Mass and section check: 4600 g inside the 110×200×38 mm outline leaves a 45.0 mm radial section, and the 156 kN static rating is 0.96× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 110 mm bore: 163 kN C divided by the 45.0 mm radial section height gives 3.6 kN per section millimetre; the 4600 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 200 over bore 110 is a 1.82× step for this size, and the 38 mm width gives a bore/width ratio of 2.89; use these ratios when housing space around the 110 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBP unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7222-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7222-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7222-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7222-BECBP?",
        "a": "7222 BECBP measures 110 mm bore × 200 mm OD × 38 mm width (4.331 × 7.874 × 1.496 in), mass about 4600 g. SKF 17000 ratings: C 163 kN, C0 156 kN, Pu 5.3 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7222-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 4,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7222-BECBP?",
        "a": "The 4,000 r/min reference (thermal) and 4,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-222-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (163/156 kN vs 280/325 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7222 BEP is the basic 110×200×38 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222-BECBP",
      "7222 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7222 BECBY",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 163,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7222 BECBY is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 110×200×38 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 110×200×38 mm (4.331×7.874×1.496 in), 45.0 mm radial section height, C 163 kN, C0 156 kN, Pu 5.3 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size, catalogue mass 4600 g. Sizing arithmetic on the 110 mm bore: 163 kN C divided by the 45.0 mm radial section height gives 3.6 kN per section millimetre; the 4600 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 38 mm width over a 45.0 mm section yields 0.84 mm of ring width per section millimetre, and the bearing weighs 4600 g for 163 kN of dynamic capacity — about 28 g per rated kN. Bore-to-OD planning: OD 200 over bore 110 is a 1.82× step for this size, and the 38 mm width gives a bore/width ratio of 2.89; use these ratios when housing space around the 110 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "process pump and compressor drives",
      "printing and paper-machine rolls",
      "crane sheave and hoist gearboxes"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly m6 on a 110 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly m6 on a 110 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7222-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7222-BECBY?",
        "a": "7222 BECBY measures 110 mm bore × 200 mm OD × 38 mm width (4.331 × 7.874 × 1.496 in), mass about 4600 g. SKF 17000 ratings: C 163 kN, C0 156 kN, Pu 5.3 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "Can one 7222-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7222-BECBY need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-222-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (163/156 kN vs 280/325 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7222 BEP is the basic 110×200×38 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222-BECBY",
      "7222 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7222-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7222 BECBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 163,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7222 BECBM is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 110×200×38 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 110×200×38 mm (4.331×7.874×1.496 in), 45.0 mm radial section height, C 163 kN, C0 156 kN, Pu 5.3 kN.reference speed 4,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 4600 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,000 r/min while thermal balance under catalogue load sets the 4,000 r/min reference; at dm ≈ 155.0 mm the corresponding dn is approximately 775k mm·r/min. Envelope economics: the 38 mm width over a 45.0 mm section yields 0.84 mm of ring width per section millimetre, and the bearing weighs 4600 g for 163 kN of dynamic capacity — about 28 g per rated kN. Bore-to-OD planning: OD 200 over bore 110 is a 1.82× step for this size, and the 38 mm width gives a bore/width ratio of 2.89; use these ratios when housing space around the 110 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7222-BECBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7222-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7222-BECBM?",
        "a": "7222 BECBM measures 110 mm bore × 200 mm OD × 38 mm width (4.331 × 7.874 × 1.496 in), mass about 4600 g. SKF 17000 ratings: C 163 kN, C0 156 kN, Pu 5.3 kN, reference speed 4,000 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7222-BECBM?",
        "a": "The 4,000 r/min reference (thermal) and 5,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7222-BECBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7222-BEP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BEP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7222-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×200×38 mm envelope with catalogue ratings within 10 %; 7222 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-222-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (163/156 kN vs 280/325 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7222 BEP is the basic 110×200×38 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7222-BECBM",
      "7222 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322-BEY",
    "brand": "SKF",
    "manufacturer_designation": "7322 BEY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 225,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 7.2,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 10000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7322 BEY is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 110×240×50 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.. Envelope 110×240×50 mm (4.331×9.449×1.969 in), 65.0 mm radial section height, C 225 kN, C0 224 kN, Pu 7.2 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 10000 g. Envelope economics: the 50 mm width over a 65.0 mm section yields 0.77 mm of ring width per section millimetre, and the bearing weighs 10000 g for 225 kN of dynamic capacity — about 44 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,200 r/min while thermal balance under catalogue load sets the 3,400 r/min reference; at dm ≈ 175.0 mm the corresponding dn is approximately 560k mm·r/min. Bore-to-OD planning: OD 240 over bore 110 is a 2.18× step for this size, and the 50 mm width gives a bore/width ratio of 2.20; use these ratios when housing space around the 110 mm shaft is the first constraint. Ordering note: BEY is the basic single bearing with the stamped brass strip cage (Y) — light and oil-additive tolerant, but not ground on the side faces for set mounting; order BECBY for a universally matchable stamped-brass unit.",
    "applications": [
      "crane sheave and hoist gearboxes",
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEY establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly m6 on a 110 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7322-BEY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7322 BEY as the single basic stamped brass execution; the other order numbers of the 7322 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7322-BEY?",
        "a": "7322 BEY measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 10000 g. SKF 17000 ratings: C 225 kN, C0 224 kN, Pu 7.2 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the BEY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. The BEY is a basic single bearing with a stamped brass Y cage — a single unit, not a universally matchable one.."
      },
      {
        "q": "Which fits should I use for 7322-BEY?",
        "a": "With a rotating inner ring use roughly m6 on the 110 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7322-BEY?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,200 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-322-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (225/224 kN vs 390/480 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7322 BECBP is the basic 110×240×50 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322-BEY",
      "7322 BEY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322-BEM",
    "brand": "SKF",
    "manufacturer_designation": "7322 BEM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 225,
    "static_load_kN": 224,
    "fatigue_load_limit_kN": 7.2,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 10000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7322 BEM is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 110×240×50 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.. Envelope 110×240×50 mm (4.331×9.449×1.969 in), 65.0 mm radial section height, C 225 kN, C0 224 kN, Pu 7.2 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), which coincide for this size, catalogue mass 10000 g. The 7.2 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 225/224 kN ratings and 10000 g mass this execution carries about 2.05 kN of C per millimetre of bore. Selection figures for 7322 BEM: the static-to-dynamic ratio C0/C is 1.00, Pu 7.2 kN is about 3 % of C, and catalogue mass works out to roughly 91 g per millimetre of bore. Bore-to-OD planning: OD 240 over bore 110 is a 2.18× step for this size, and the 50 mm width gives a bore/width ratio of 2.20; use these ratios when housing space around the 110 mm shaft is the first constraint. Ordering note: BEM pairs the optimized 40-degree geometry with a machined one-piece brass window cage as a basic (non-universal) single bearing; it is the brass-cage counterpart of the polymer BEP, and universally matchable positions must use the BECBM or BCBM execution instead.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly m6 on a 110 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 50 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BEM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7322-BEM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7322 BEM as the single basic machined brass execution; the other order numbers of the 7322 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7322-BEM?",
        "a": "7322 BEM measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 10000 g. SKF 17000 ratings: C 225 kN, C0 224 kN, Pu 7.2 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BEM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BEM is a basic single bearing with a machined brass cage — not ground for universal matching; use the BCBM or BECBM execution when defined DB/DF sets are required.."
      },
      {
        "q": "Which grease and fill for 7322-BEM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,400 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7322-BEM?",
        "a": "The 3,400 r/min reference (thermal) and 3,400 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-322-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (225/224 kN vs 390/480 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7322 BECBP is the basic 110×240×50 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322-BEM",
      "7322 BEM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322-BECBP",
    "brand": "SKF",
    "manufacturer_designation": "7322 BECBP",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 240,
    "static_load_kN": 245,
    "fatigue_load_limit_kN": 7.8,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 10000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7322 BECBP is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 110×240×50 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 110×240×50 mm (4.331×9.449×1.969 in), 65.0 mm radial section height, C 240 kN, C0 245 kN, Pu 7.8 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 10000 g. At the printed limiting speed of 3,600 r/min the mean pitch diameter dm ≈ 175.0 mm implies a dn value around 630k mm·r/min; the 3,400 r/min reference speed is the thermal-planning figure under catalogue load. Selection figures for 7322 BECBP: the static-to-dynamic ratio C0/C is 1.02, Pu 7.8 kN is about 3 % of C, and catalogue mass works out to roughly 91 g per millimetre of bore. Bore-to-OD planning: OD 240 over bore 110 is a 2.18× step for this size, and the 50 mm width gives a bore/width ratio of 2.20; use these ratios when housing space around the 110 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.",
    "applications": [
      "vibrating screens and shale shaker shafts",
      "centrifuge and separator drives",
      "heavy feed and take-up rolls"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "PA66 cage embrittlement inside a preloaded set where heat accumulates faster than in a single mounting",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "At 110 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7322-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7322-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BECBP establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7322-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7322-BECBP?",
        "a": "7322 BECBP measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 10000 g. SKF 17000 ratings: C 240 kN, C0 245 kN, Pu 7.8 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BECBP suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7322-BECBP?",
        "a": "With a rotating inner ring use roughly m6 on the 110 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7322-BECBP?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume, and stay within the — the PA66 cage sets the ceiling, not the steel. Oil-air or oil-jet lubrication is the choice near the 3,600 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-322-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (240/245 kN vs 390/480 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7322 BECBP is the basic 110×240×50 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322-BECBP",
      "7322 BECBP"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322-BECBY",
    "brand": "SKF",
    "manufacturer_designation": "7322 BECBY",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 240,
    "static_load_kN": 245,
    "fatigue_load_limit_kN": 7.8,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 10000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7322 BECBY is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 110×240×50 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage. Envelope 110×240×50 mm (4.331×9.449×1.969 in), 65.0 mm radial section height, C 240 kN, C0 245 kN, Pu 7.8 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 10000 g. At the printed limiting speed of 3,600 r/min the mean pitch diameter dm ≈ 175.0 mm implies a dn value around 630k mm·r/min; the 3,400 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,600 r/min while thermal balance under catalogue load sets the 3,400 r/min reference; at dm ≈ 175.0 mm the corresponding dn is approximately 630k mm·r/min. Bore-to-OD planning: OD 240 over bore 110 is a 2.18× step for this size, and the 50 mm width gives a bore/width ratio of 2.20; use these ratios when housing space around the 110 mm shaft is the first constraint. Cage detail specific to this order number: the Y cage is stamped from brass strip into ball pockets rather than machined from solid, giving a lighter cage assembly and lower centrifugal mass than the M execution; it remains brass (temperature and oil-additive tolerant, unlike PA66) but is the formed-cage design, and the machined-brass BECBM order number remains the choice for severe shock or marginal lubrication.",
    "applications": [
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers",
      "process pump and compressor drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "stamped brass cage pocket deformation after shock loading beyond the lighter formed cage capacity",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBY unit is ground for arbitrary pairing, a basic execution is not.",
      "Assign interference to the rotating ring — roughly m6 on a 110 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "The steep 40° angle of 7322-BECBY favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBY bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7322-BECBY?",
        "a": "7322 BECBY measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 10000 g. SKF 17000 ratings: C 240 kN, C0 245 kN, Pu 7.8 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BECBY suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. stamped brass cage, ball-centred (suffix Y) — lighter than the machined M cage but brass rather than polymer. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. BECBY combines the optimized 40° geometry with CB universal clearance and a stamped brass Y cage."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7322-BECBY?",
        "a": "The 3,400 r/min reference (thermal) and 3,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7322-BECBY take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-322-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (240/245 kN vs 390/480 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7322 BECBP is the basic 110×240×50 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322-BECBY",
      "7322 BECBY"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7322-BECBM",
    "brand": "SKF",
    "manufacturer_designation": "7322 BECBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 240,
    "static_load_kN": 245,
    "fatigue_load_limit_kN": 7.8,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 10000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7322 BECBM is SKF's 110 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 110×240×50 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 110×240×50 mm (4.331×9.449×1.969 in), 65.0 mm radial section height, C 240 kN, C0 245 kN, Pu 7.8 kN.reference speed 3,400 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 10000 g. Load balance: C0 245 kN against C 240 kN gives a 1.02 ratio, typical of a steep-angle axial-oriented design; Pu 7.8 kN enters the SKF adjusted-life equation rather than the basic rating life. The 7.8 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 240/245 kN ratings and 10000 g mass this execution carries about 2.18 kN of C per millimetre of bore. Bore-to-OD planning: OD 240 over bore 110 is a 2.18× step for this size, and the 50 mm width gives a bore/width ratio of 2.20; use these ratios when housing space around the 110 mm shaft is the first constraint. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.",
    "applications": [
      "dryer-cylinder pinion shafts",
      "medium and large machine-tool spindles",
      "industrial gearboxes and speed reducers"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "brass cage-pocket smearing under long periods of unloaded running with marginal oil film",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Fillet radii must clear the chamfer so the 50 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7322-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7322-BECBM?",
        "a": "7322 BECBM measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 10000 g. SKF 17000 ratings: C 240 kN, C0 245 kN, Pu 7.8 kN, reference speed 3,400 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the BECBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7322-BECBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,500 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7322-BECBM?",
        "a": "The 3,400 r/min reference (thermal) and 4,500 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-NTN",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BEM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBP is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 110×240×50 mm envelope with catalogue ratings within 10 %; 7322 BECBY is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-322-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (240/245 kN vs 390/480 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "SKF SKF 7322 BECBP is the basic 110×240×50 mm angular-contact page with ratings within 10 % of this execution — same boundary dimensions, verify execution details."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7322-BECBM",
      "7322 BECBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7024-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7024 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 180,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 87.1,
    "static_load_kN": 93,
    "fatigue_load_limit_kN": 3.2,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 2400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7024 BGM is SKF's 120 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 120×180×28 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 120×180×28 mm (4.724×7.087×1.102 in), 30.0 mm radial section height, C 87.1 kN, C0 93 kN, Pu 3.2 kN.reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size, catalogue mass 2400 g. Load balance: C0 93 kN against C 87.1 kN gives a 1.07 ratio, typical of a steep-angle axial-oriented design; Pu 3.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 120 mm bore: 87.1 kN C divided by the 30.0 mm radial section height gives 2.9 kN per section millimetre; the 2400 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 180 over bore 120 is a 1.50× step for this size, and the 28 mm width gives a bore/width ratio of 4.29; use these ratios when housing space around the 120 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "vertical mill separator drives",
      "heavy industrial gearboxes",
      "large process pumps and compressors"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BGM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Do not mix execution classes inside one set: a universally matchable BGM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7024-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7024 BGM as the single g brass execution; the other order numbers of the 7024 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7024-BGM?",
        "a": "7024 BGM measures 120 mm bore × 180 mm OD × 28 mm width (4.724 × 7.087 × 1.102 in), mass about 2400 g. SKF 17000 ratings: C 87.1 kN, C0 93 kN, Pu 3.2 kN, reference speed 4,000 r/min (thermal) and limiting speed 4,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Which grease and fill for 7024-BGM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7024-BGM?",
        "a": "The 4,000 r/min reference (thermal) and 4,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7024",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 120×180×28 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7024",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7024-BGM",
      "7024 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7224-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7224 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 165,
    "static_load_kN": 163,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 5900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7224 BCBM is SKF's 120 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 120×215×40 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 120×215×40 mm (4.724×8.465×1.575 in), 47.5 mm radial section height, C 165 kN, C0 163 kN, Pu 5.3 kN.reference speed 3,600 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 5900 g. Load balance: C0 163 kN against C 165 kN gives a 0.99 ratio, typical of a steep-angle axial-oriented design; Pu 5.3 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 120 mm bore: 165 kN C divided by the 47.5 mm radial section height gives 3.5 kN per section millimetre; the 5900 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 215 over bore 120 is a 1.79× step for this size, and the 40 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 120 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7224-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7224-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7224-BCBM?",
        "a": "7224 BCBM measures 120 mm bore × 215 mm OD × 40 mm width (4.724 × 8.465 × 1.575 in), mass about 5900 g. SKF 17000 ratings: C 165 kN, C0 163 kN, Pu 5.3 kN, reference speed 3,600 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7224-BCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 4,000 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7224-BCBM?",
        "a": "The 3,600 r/min reference (thermal) and 4,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7224",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7224-BM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 120×215×40 mm envelope with catalogue ratings within 10 %; 7224 BM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-224-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope, but catalogue C/C0 differ between executions (165/163 kN vs 300/365 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7224-BCBM",
      "7224 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7224-BM",
    "brand": "SKF",
    "manufacturer_designation": "7224 BM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 165,
    "static_load_kN": 163,
    "fatigue_load_limit_kN": 5.3,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 5900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7224 BM is SKF's 120 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 120×215×40 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.. Envelope 120×215×40 mm (4.724×8.465×1.575 in), 47.5 mm radial section height, C 165 kN, C0 163 kN, Pu 5.3 kN.reference speed 3,600 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 5900 g. At the printed limiting speed of 4,000 r/min the mean pitch diameter dm ≈ 167.5 mm implies a dn value around 670k mm·r/min; the 3,600 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min while thermal balance under catalogue load sets the 3,600 r/min reference; at dm ≈ 167.5 mm the corresponding dn is approximately 670k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 4,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.90. Non-optimized basic execution: BM is the earlier 40-degree design without the E internal upgrade, fitted with a machined brass ball-centred cage as a single (non-universal) bearing; quote it for housings and spacers designed around the legacy geometry.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "legacy-geometry cage smearing when the non-E basic bearing is run at speeds developed for the optimized E design",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BM unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Fillet radii must clear the chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7224-BM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7224-BM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7224 BM as the single non e brass execution; the other order numbers of the 7224 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7224-BM?",
        "a": "7224 BM measures 120 mm bore × 215 mm OD × 40 mm width (4.724 × 8.465 × 1.575 in), mass about 5900 g. SKF 17000 ratings: C 165 kN, C0 163 kN, Pu 5.3 kN, reference speed 3,600 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the BM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7224-BM?",
        "a": "The 3,600 r/min reference (thermal) and 4,000 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7224-BM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7224",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7224-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 120×215×40 mm envelope with catalogue ratings within 10 %; 7224 BCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-224-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope, but catalogue C/C0 differ between executions (165/163 kN vs 300/365 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7224-BM",
      "7224 BM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7324-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7324 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 260,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 238,
    "static_load_kN": 250,
    "fatigue_load_limit_kN": 7.65,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 14500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7324 BCBM is SKF's 120 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 120×260×55 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 120×260×55 mm (4.724×10.236×2.165 in), 70.0 mm radial section height, C 238 kN, C0 250 kN, Pu 7.65 kN.reference speed 3,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 14500 g. At the printed limiting speed of 3,600 r/min the mean pitch diameter dm ≈ 190.0 mm implies a dn value around 684k mm·r/min; the 3,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 55 mm width over a 70.0 mm section yields 0.79 mm of ring width per section millimetre, and the bearing weighs 14500 g for 238 kN of dynamic capacity — about 61 g per rated kN. Bore-to-OD planning: OD 260 over bore 120 is a 2.17× step for this size, and the 55 mm width gives a bore/width ratio of 2.18; use these ratios when housing space around the 120 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly m6 on a 120 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 55 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7324-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7324-BCBM?",
        "a": "7324 BCBM measures 120 mm bore × 260 mm OD × 55 mm width (4.724 × 10.236 × 2.165 in), mass about 14500 g. SKF 17000 ratings: C 238 kN, C0 250 kN, Pu 7.65 kN, reference speed 3,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7324-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 120 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7324-BCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,600 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7324",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 120×260×55 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "QJ-324-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×260×55 mm envelope, but catalogue C/C0 differ between executions (238/250 kN vs 415/530 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7324-BCBM",
      "7324 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7226-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7226 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 186,
    "static_load_kN": 193,
    "fatigue_load_limit_kN": 6.1,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 6950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7226 BCBM is SKF's 130 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 130×230×40 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 130×230×40 mm (5.118×9.055×1.575 in), 50.0 mm radial section height, C 186 kN, C0 193 kN, Pu 6.1 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 6950 g. Sizing arithmetic on the 130 mm bore: 186 kN C divided by the 50.0 mm radial section height gives 3.7 kN per section millimetre; the 6950 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 6950 g inside the 130×230×40 mm outline leaves a 50.0 mm radial section, and the 193 kN static rating is 1.04× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 3,400 r/min against a 3,800 r/min limiting speed, i.e. a reference-to-limit ratio of 0.89. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly m6 on a 130 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7226-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7226-BCBM?",
        "a": "7226 BCBM measures 130 mm bore × 230 mm OD × 40 mm width (5.118 × 9.055 × 1.575 in), mass about 6950 g. SKF 17000 ratings: C 186 kN, C0 193 kN, Pu 6.1 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7226-BCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,800 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7226-BCBM?",
        "a": "The 3,400 r/min reference (thermal) and 3,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7226",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7226-BM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 130×230×40 mm envelope with catalogue ratings within 10 %; 7226 BM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-226-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope, but catalogue C/C0 differ between executions (186/193 kN vs 310/400 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7226-BCBM",
      "7226 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7226-BM",
    "brand": "SKF",
    "manufacturer_designation": "7226 BM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 186,
    "static_load_kN": 193,
    "fatigue_load_limit_kN": 6.1,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 6950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7226 BM is SKF's 130 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 130×230×40 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.. Envelope 130×230×40 mm (5.118×9.055×1.575 in), 50.0 mm radial section height, C 186 kN, C0 193 kN, Pu 6.1 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 6950 g. Envelope economics: the 40 mm width over a 50.0 mm section yields 0.80 mm of ring width per section millimetre, and the bearing weighs 6950 g for 186 kN of dynamic capacity — about 37 g per rated kN. Selection figures for 7226 BM: the static-to-dynamic ratio C0/C is 1.04, Pu 6.1 kN is about 3 % of C, and catalogue mass works out to roughly 53 g per millimetre of bore. Bore-to-OD planning: OD 230 over bore 130 is a 1.77× step for this size, and the 40 mm width gives a bore/width ratio of 3.25; use these ratios when housing space around the 130 mm shaft is the first constraint. Non-optimized basic execution: BM is the earlier 40-degree design without the E internal upgrade, fitted with a machined brass ball-centred cage as a single (non-universal) bearing; quote it for housings and spacers designed around the legacy geometry.",
    "applications": [
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts",
      "hydraulic press and converter tilt drives"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "legacy-geometry cage smearing when the non-E basic bearing is run at speeds developed for the optimized E design",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 40 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7226-BM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7226 BM as the single non e brass execution; the other order numbers of the 7226 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7226-BM?",
        "a": "7226 BM measures 130 mm bore × 230 mm OD × 40 mm width (5.118 × 9.055 × 1.575 in), mass about 6950 g. SKF 17000 ratings: C 186 kN, C0 193 kN, Pu 6.1 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the BM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7226-BM?",
        "a": "The 3,400 r/min reference (thermal) and 3,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7226-BM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7226",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7226-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 130×230×40 mm envelope with catalogue ratings within 10 %; 7226 BCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-226-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope, but catalogue C/C0 differ between executions (186/193 kN vs 310/400 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7226-BM",
      "7226 BM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7326-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7326 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 280,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 276,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 17000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7326 BCBM is SKF's 130 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 130×280×58 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 130×280×58 mm (5.118×11.024×2.283 in), 75.0 mm radial section height, C 276 kN, C0 305 kN, Pu 9 kN.reference speed 2,800 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 17000 g. Selection figures for 7326 BCBM: the static-to-dynamic ratio C0/C is 1.11, Pu 9 kN is about 3 % of C, and catalogue mass works out to roughly 131 g per millimetre of bore. At the printed limiting speed of 3,400 r/min the mean pitch diameter dm ≈ 205.0 mm implies a dn value around 697k mm·r/min; the 2,800 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 2,800 r/min against a 3,400 r/min limiting speed, i.e. a reference-to-limit ratio of 0.82. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "hydraulic press and converter tilt drives",
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7326-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7326-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7326-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7326-BCBM?",
        "a": "7326 BCBM measures 130 mm bore × 280 mm OD × 58 mm width (5.118 × 11.024 × 2.283 in), mass about 17000 g. SKF 17000 ratings: C 276 kN, C0 305 kN, Pu 9 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7326-BCBM?",
        "a": "The 2,800 r/min reference (thermal) and 3,400 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7326-BCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7326",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7326-BM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 130×280×58 mm envelope with catalogue ratings within 10 %; 7326 BM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-326-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×280×58 mm envelope, but catalogue C/C0 differ between executions (276/305 kN vs 455/610 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7326-BCBM",
      "7326 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7326-BM",
    "brand": "SKF",
    "manufacturer_designation": "7326 BM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 280,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 276,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 17000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7326 BM is SKF's 130 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 130×280×58 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.. Envelope 130×280×58 mm (5.118×11.024×2.283 in), 75.0 mm radial section height, C 276 kN, C0 305 kN, Pu 9 kN.reference speed 2,800 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 17000 g. Mass and section check: 17000 g inside the 130×280×58 mm outline leaves a 75.0 mm radial section, and the 305 kN static rating is 1.11× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 3,400 r/min the mean pitch diameter dm ≈ 205.0 mm implies a dn value around 697k mm·r/min; the 2,800 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 280 over bore 130 is a 2.15× step for this size, and the 58 mm width gives a bore/width ratio of 2.24; use these ratios when housing space around the 130 mm shaft is the first constraint. Non-optimized basic execution: BM is the earlier 40-degree design without the E internal upgrade, fitted with a machined brass ball-centred cage as a single (non-universal) bearing; quote it for housings and spacers designed around the legacy geometry.",
    "applications": [
      "heavy industrial gearboxes",
      "large process pumps and compressors",
      "marine propulsion and deck machinery"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "legacy-geometry cage smearing when the non-E basic bearing is run at speeds developed for the optimized E design",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Assign interference to the rotating ring — roughly m6 on a 130 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly m6 on a 130 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7326-BM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7326 BM as the single non e brass execution; the other order numbers of the 7326 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7326-BM?",
        "a": "7326 BM measures 130 mm bore × 280 mm OD × 58 mm width (5.118 × 11.024 × 2.283 in), mass about 17000 g. SKF 17000 ratings: C 276 kN, C0 305 kN, Pu 9 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the BM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.."
      },
      {
        "q": "Which grease and fill for 7326-BM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,400 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7326-BM?",
        "a": "The 2,800 r/min reference (thermal) and 3,400 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7326",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7326-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 130×280×58 mm envelope with catalogue ratings within 10 %; 7326 BCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-326-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×280×58 mm envelope, but catalogue C/C0 differ between executions (276/305 kN vs 455/610 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7326-BM",
      "7326 BM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7028-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7028 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 210,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 114,
    "static_load_kN": 129,
    "fatigue_load_limit_kN": 4.15,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 3850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7028 BGM is SKF's 140 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 140×210×33 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 140×210×33 mm (5.512×8.268×1.299 in), 35.0 mm radial section height, C 114 kN, C0 129 kN, Pu 4.15 kN.reference speed 3,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), which coincide for this size, catalogue mass 3850 g. Mass and section check: 3850 g inside the 140×210×33 mm outline leaves a 35.0 mm radial section, and the 129 kN static rating is 1.13× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 4.15 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 114/129 kN ratings and 3850 g mass this execution carries about 0.81 kN of C per millimetre of bore. Bore-to-OD planning: OD 210 over bore 140 is a 1.50× step for this size, and the 33 mm width gives a bore/width ratio of 4.24; use these ratios when housing space around the 140 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts"
    ],
    "failure_modes": [
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 33 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7028-BGM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "The steep 40° angle of 7028-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7028 BGM as the single g brass execution; the other order numbers of the 7028 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7028-BGM?",
        "a": "7028 BGM measures 140 mm bore × 210 mm OD × 33 mm width (5.512 × 8.268 × 1.299 in), mass about 3850 g. SKF 17000 ratings: C 114 kN, C0 129 kN, Pu 4.15 kN, reference speed 3,400 r/min (thermal) and limiting speed 3,400 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Which grease and fill for 7028-BGM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,400 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7028-BGM?",
        "a": "The 3,400 r/min reference (thermal) and 3,400 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7028",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 140×210×33 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7028",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7028-BGM",
      "7028 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7228-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7228 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 250,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 199,
    "static_load_kN": 212,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 8850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7228 BCBM is SKF's 140 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 140×250×42 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 140×250×42 mm (5.512×9.843×1.654 in), 55.0 mm radial section height, C 199 kN, C0 212 kN, Pu 6.4 kN.reference speed 3,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 8850 g. Mass and section check: 8850 g inside the 140×250×42 mm outline leaves a 55.0 mm radial section, and the 212 kN static rating is 1.07× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 6.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 199/212 kN ratings and 8850 g mass this execution carries about 1.42 kN of C per millimetre of bore. Bore-to-OD planning: OD 250 over bore 140 is a 1.79× step for this size, and the 42 mm width gives a bore/width ratio of 3.33; use these ratios when housing space around the 140 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 42 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7228-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7228-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7228-BCBM?",
        "a": "7228 BCBM measures 140 mm bore × 250 mm OD × 42 mm width (5.512 × 9.843 × 1.654 in), mass about 8850 g. SKF 17000 ratings: C 199 kN, C0 212 kN, Pu 6.4 kN, reference speed 3,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7228-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 140 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7228",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7228-BM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 140×250×42 mm envelope with catalogue ratings within 10 %; 7228 BM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-228-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope, but catalogue C/C0 differ between executions (199/212 kN vs 345/475 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7228-BCBM",
      "7228 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7228-BM",
    "brand": "SKF",
    "manufacturer_designation": "7228 BM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 250,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 199,
    "static_load_kN": 212,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 8850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7228 BM is SKF's 140 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 140×250×42 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.. Envelope 140×250×42 mm (5.512×9.843×1.654 in), 55.0 mm radial section height, C 199 kN, C0 212 kN, Pu 6.4 kN.reference speed 3,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 8850 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,600 r/min while thermal balance under catalogue load sets the 3,000 r/min reference; at dm ≈ 195.0 mm the corresponding dn is approximately 702k mm·r/min. At the printed limiting speed of 3,600 r/min the mean pitch diameter dm ≈ 195.0 mm implies a dn value around 702k mm·r/min; the 3,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 3,000 r/min against a 3,600 r/min limiting speed, i.e. a reference-to-limit ratio of 0.83. Non-optimized basic execution: BM is the earlier 40-degree design without the E internal upgrade, fitted with a machined brass ball-centred cage as a single (non-universal) bearing; quote it for housings and spacers designed around the legacy geometry.",
    "applications": [
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives",
      "heavy industrial gearboxes"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "legacy-geometry cage smearing when the non-E basic bearing is run at speeds developed for the optimized E design",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 42 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "One 7228-BM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7228-BM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7228 BM as the single non e brass execution; the other order numbers of the 7228 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7228-BM?",
        "a": "7228 BM measures 140 mm bore × 250 mm OD × 42 mm width (5.512 × 9.843 × 1.654 in), mass about 8850 g. SKF 17000 ratings: C 199 kN, C0 212 kN, Pu 6.4 kN, reference speed 3,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the BM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.."
      },
      {
        "q": "Which fits should I use for 7228-BM?",
        "a": "With a rotating inner ring use roughly m6 on the 140 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7228-BM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,600 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7228",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7228-BCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 140×250×42 mm envelope with catalogue ratings within 10 %; 7228 BCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-228-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope, but catalogue C/C0 differ between executions (199/212 kN vs 345/475 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7228-BM",
      "7228 BM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7328-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7328 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 300,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 302,
    "static_load_kN": 345,
    "fatigue_load_limit_kN": 9.8,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 21500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7328 BCBM is SKF's 140 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 140×300×62 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 140×300×62 mm (5.512×11.811×2.441 in), 80.0 mm radial section height, C 302 kN, C0 345 kN, Pu 9.8 kN.reference speed 2,600 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 21500 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,000 r/min while thermal balance under catalogue load sets the 2,600 r/min reference; at dm ≈ 220.0 mm the corresponding dn is approximately 660k mm·r/min. Selection figures for 7328 BCBM: the static-to-dynamic ratio C0/C is 1.14, Pu 9.8 kN is about 3 % of C, and catalogue mass works out to roughly 154 g per millimetre of bore. Bore-to-OD planning: OD 300 over bore 140 is a 2.14× step for this size, and the 62 mm width gives a bore/width ratio of 2.26; use these ratios when housing space around the 140 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "large process pumps and compressors",
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 62 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "At 140 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7328-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7328-BCBM?",
        "a": "7328 BCBM measures 140 mm bore × 300 mm OD × 62 mm width (5.512 × 11.811 × 2.441 in), mass about 21500 g. SKF 17000 ratings: C 302 kN, C0 345 kN, Pu 9.8 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7328-BCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7328",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "QJ-328-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×300×62 mm envelope, but catalogue C/C0 differ between executions (302/345 kN vs 500/695 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7328-BCBM",
      "7328 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7030-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7030 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 225,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 133,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 4.55,
    "reference_speed_rpm": 3200,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 4700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7030 BGM is SKF's 150 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 150×225×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 150×225×35 mm (5.906×8.858×1.378 in), 37.5 mm radial section height, C 133 kN, C0 146 kN, Pu 4.55 kN.reference speed 3,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical), which coincide for this size, catalogue mass 4700 g. Envelope economics: the 35 mm width over a 37.5 mm section yields 0.93 mm of ring width per section millimetre, and the bearing weighs 4700 g for 133 kN of dynamic capacity — about 35 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,200 r/min while thermal balance under catalogue load sets the 3,200 r/min reference; at dm ≈ 187.5 mm the corresponding dn is approximately 600k mm·r/min. Bore-to-OD planning: OD 225 over bore 150 is a 1.50× step for this size, and the 35 mm width gives a bore/width ratio of 4.29; use these ratios when housing space around the 150 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Do not mix execution classes inside one set: a universally matchable BGM unit is ground for arbitrary pairing, a basic execution is not.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BGM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7030-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7030 BGM as the single g brass execution; the other order numbers of the 7030 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7030-BGM?",
        "a": "7030 BGM measures 150 mm bore × 225 mm OD × 35 mm width (5.906 × 8.858 × 1.378 in), mass about 4700 g. SKF 17000 ratings: C 133 kN, C0 146 kN, Pu 4.55 kN, reference speed 3,200 r/min (thermal) and limiting speed 3,200 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Which fits should I use for 7030-BGM?",
        "a": "With a rotating inner ring use roughly m6 on the 150 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7030-BGM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,200 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7030",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 150×225×35 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7030",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7030-BGM",
      "7030 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7230-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7230 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 270,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 216,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 11500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7230 BCBM is SKF's 150 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 150×270×45 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 150×270×45 mm (5.906×10.63×1.772 in), 60.0 mm radial section height, C 216 kN, C0 240 kN, Pu 6.95 kN.reference speed 2,800 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 11500 g. Selection figures for 7230 BCBM: the static-to-dynamic ratio C0/C is 1.11, Pu 6.95 kN is about 3 % of C, and catalogue mass works out to roughly 77 g per millimetre of bore. At the printed limiting speed of 3,200 r/min the mean pitch diameter dm ≈ 210.0 mm implies a dn value around 672k mm·r/min; the 2,800 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 270 over bore 150 is a 1.80× step for this size, and the 45 mm width gives a bore/width ratio of 3.33; use these ratios when housing space around the 150 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives",
      "heavy industrial gearboxes"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At 150 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "One 7230-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 45 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7230-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7230-BCBM?",
        "a": "7230 BCBM measures 150 mm bore × 270 mm OD × 45 mm width (5.906 × 10.63 × 1.772 in), mass about 11500 g. SKF 17000 ratings: C 216 kN, C0 240 kN, Pu 6.95 kN, reference speed 2,800 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7230-BCBM?",
        "a": "The 2,800 r/min reference (thermal) and 3,200 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7230-BCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7230",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 150×270×45 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "QJ-230-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×270×45 mm envelope, but catalogue C/C0 differ between executions (216/240 kN vs 400/570 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7230-BCBM",
      "7230 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7330-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7330 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 320,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 332,
    "static_load_kN": 390,
    "fatigue_load_limit_kN": 10.8,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 26000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7330 BCBM is SKF's 150 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 150×320×65 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 150×320×65 mm (5.906×12.598×2.559 in), 85.0 mm radial section height, C 332 kN, C0 390 kN, Pu 10.8 kN.reference speed 2,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 26000 g. The 10.8 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 332/390 kN ratings and 26000 g mass this execution carries about 2.21 kN of C per millimetre of bore. Load balance: C0 390 kN against C 332 kN gives a 1.17 ratio, typical of a steep-angle axial-oriented design; Pu 10.8 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 320 over bore 150 is a 2.13× step for this size, and the 65 mm width gives a bore/width ratio of 2.31; use these ratios when housing space around the 150 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "hydraulic press and converter tilt drives",
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7330-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7330-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7330-BCBM?",
        "a": "7330 BCBM measures 150 mm bore × 320 mm OD × 65 mm width (5.906 × 12.598 × 2.559 in), mass about 26000 g. SKF 17000 ratings: C 332 kN, C0 390 kN, Pu 10.8 kN, reference speed 2,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7330-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 150 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7330",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "QJ-330-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×320×65 mm envelope, but catalogue C/C0 differ between executions (332/390 kN vs 530/765 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7330-BCBM",
      "7330 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7232-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7232 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 290,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 255,
    "static_load_kN": 300,
    "fatigue_load_limit_kN": 8.5,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 14000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7232 BCBM is SKF's 160 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 160×290×48 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 160×290×48 mm (6.299×11.417×1.89 in), 65.0 mm radial section height, C 255 kN, C0 300 kN, Pu 8.5 kN.reference speed 2,600 r/min (thermal) and limiting speed 3,000 r/min (mechanical), catalogue mass 14000 g. At the printed limiting speed of 3,000 r/min the mean pitch diameter dm ≈ 225.0 mm implies a dn value around 675k mm·r/min; the 2,600 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 48 mm width over a 65.0 mm section yields 0.74 mm of ring width per section millimetre, and the bearing weighs 14000 g for 255 kN of dynamic capacity — about 55 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 2,600 r/min against a 3,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.87. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "marine propulsion and deck machinery",
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7232-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly m6 on a 160 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7232-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7232-BCBM?",
        "a": "7232 BCBM measures 160 mm bore × 290 mm OD × 48 mm width (6.299 × 11.417 × 1.89 in), mass about 14000 g. SKF 17000 ratings: C 255 kN, C0 300 kN, Pu 8.5 kN, reference speed 2,600 r/min (thermal) and limiting speed 3,000 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use for 7232-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 160 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7232-BCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 3,000 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7232",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 160×290×48 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "QJ-232-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 160×290×48 mm envelope, but catalogue C/C0 differ between executions (255/300 kN vs 450/670 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7232-BCBM",
      "7232 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7034-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7034 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 260,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 172,
    "static_load_kN": 204,
    "fatigue_load_limit_kN": 5.85,
    "reference_speed_rpm": 2800,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 7650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7034 BGM is SKF's 170 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 170×260×42 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 170×260×42 mm (6.693×10.236×1.654 in), 45.0 mm radial section height, C 172 kN, C0 204 kN, Pu 5.85 kN.reference speed 2,800 r/min (thermal) and limiting speed 2,800 r/min (mechanical), which coincide for this size, catalogue mass 7650 g. Selection figures for 7034 BGM: the static-to-dynamic ratio C0/C is 1.19, Pu 5.85 kN is about 3 % of C, and catalogue mass works out to roughly 45 g per millimetre of bore. At the printed limiting speed of 2,800 r/min the mean pitch diameter dm ≈ 215.0 mm implies a dn value around 602k mm·r/min; the 2,800 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 260 over bore 170 is a 1.53× step for this size, and the 42 mm width gives a bore/width ratio of 4.05; use these ratios when housing space around the 170 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "heavy industrial gearboxes",
      "large process pumps and compressors",
      "marine propulsion and deck machinery"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "At 170 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Assign interference to the rotating ring — roughly m6 on a 170 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7034-BGM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7034-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7034 BGM as the single g brass execution; the other order numbers of the 7034 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7034-BGM?",
        "a": "7034 BGM measures 170 mm bore × 260 mm OD × 42 mm width (6.693 × 10.236 × 1.654 in), mass about 7650 g. SKF 17000 ratings: C 172 kN, C0 204 kN, Pu 5.85 kN, reference speed 2,800 r/min (thermal) and limiting speed 2,800 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Which fits should I use for 7034-BGM?",
        "a": "With a rotating inner ring use roughly m6 on the 170 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7034-BGM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 2,800 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7034",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 170×260×42 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7034",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7034-BGM",
      "7034 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7234-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7234 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 310,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 281,
    "static_load_kN": 345,
    "fatigue_load_limit_kN": 9.5,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 17500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7234 BCBM is SKF's 170 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 170×310×52 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 170×310×52 mm (6.693×12.205×2.047 in), 70.0 mm radial section height, C 281 kN, C0 345 kN, Pu 9.5 kN.reference speed 2,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 17500 g. Envelope economics: the 52 mm width over a 70.0 mm section yields 0.74 mm of ring width per section millimetre, and the bearing weighs 17500 g for 281 kN of dynamic capacity — about 62 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 2,800 r/min while thermal balance under catalogue load sets the 2,400 r/min reference; at dm ≈ 240.0 mm the corresponding dn is approximately 672k mm·r/min. Bore-to-OD planning: OD 310 over bore 170 is a 1.82× step for this size, and the 52 mm width gives a bore/width ratio of 3.27; use these ratios when housing space around the 170 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "vertical mill separator drives",
      "heavy industrial gearboxes",
      "large process pumps and compressors"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Assign interference to the rotating ring — roughly m6 on a 170 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7234-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7234-BCBM?",
        "a": "7234 BCBM measures 170 mm bore × 310 mm OD × 52 mm width (6.693 × 12.205 × 2.047 in), mass about 17500 g. SKF 17000 ratings: C 281 kN, C0 345 kN, Pu 9.5 kN, reference speed 2,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7234-BCBM?",
        "a": "The 2,400 r/min reference (thermal) and 2,800 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7234-BCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7234",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 170×310×52 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "QJ-234-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×310×52 mm envelope, but catalogue C/C0 differ between executions (281/345 kN vs 455/720 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7234-BCBM",
      "7234 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7334-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7334 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 360,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 390,
    "static_load_kN": 490,
    "fatigue_load_limit_kN": 12.7,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 36000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7334 BCBM is SKF's 170 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 170×360×72 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 170×360×72 mm (6.693×14.173×2.835 in), 95.0 mm radial section height, C 390 kN, C0 490 kN, Pu 12.7 kN.reference speed 2,200 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 36000 g. Sizing arithmetic on the 170 mm bore: 390 kN C divided by the 95.0 mm radial section height gives 4.1 kN per section millimetre; the 36000 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 36000 g inside the 170×360×72 mm outline leaves a 95.0 mm radial section, and the 490 kN static rating is 1.26× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 360 over bore 170 is a 2.12× step for this size, and the 72 mm width gives a bore/width ratio of 2.36; use these ratios when housing space around the 170 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives",
      "heavy industrial gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "One 7334-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "One 7334-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7334-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7334-BCBM?",
        "a": "7334 BCBM measures 170 mm bore × 360 mm OD × 72 mm width (6.693 × 14.173 × 2.835 in), mass about 36000 g. SKF 17000 ratings: C 390 kN, C0 490 kN, Pu 12.7 kN, reference speed 2,200 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7334-BCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 2,600 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7334-BCBM?",
        "a": "The 2,200 r/min reference (thermal) and 2,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7334",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "QJ-334-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×360×72 mm envelope, but catalogue C/C0 differ between executions (390/490 kN vs 655/1040 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7334-BCBM",
      "7334 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7036-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7036 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 280,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 195,
    "static_load_kN": 240,
    "fatigue_load_limit_kN": 6.7,
    "reference_speed_rpm": 2600,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 10000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7036 BGM is SKF's 180 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 180×280×46 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 180×280×46 mm (7.087×11.024×1.811 in), 50.0 mm radial section height, C 195 kN, C0 240 kN, Pu 6.7 kN.reference speed 2,600 r/min (thermal) and limiting speed 2,600 r/min (mechanical), which coincide for this size, catalogue mass 10000 g. At the printed limiting speed of 2,600 r/min the mean pitch diameter dm ≈ 230.0 mm implies a dn value around 598k mm·r/min; the 2,600 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 46 mm width over a 50.0 mm section yields 0.92 mm of ring width per section millimetre, and the bearing weighs 10000 g for 195 kN of dynamic capacity — about 51 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 2,600 r/min against a 2,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "sugar mill and cement kiln pinion shafts",
      "hydraulic press and converter tilt drives",
      "heavy dredge and excavator swing drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 46 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 180 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Do not mix execution classes inside one set: a universally matchable BGM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7036-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7036 BGM as the single g brass execution; the other order numbers of the 7036 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7036-BGM?",
        "a": "7036 BGM measures 180 mm bore × 280 mm OD × 46 mm width (7.087 × 11.024 × 1.811 in), mass about 10000 g. SKF 17000 ratings: C 195 kN, C0 240 kN, Pu 6.7 kN, reference speed 2,600 r/min (thermal) and limiting speed 2,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "What minimum axial load does 7036-BGM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7036",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 180×280×46 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7036",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7036-BGM",
      "7036 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7236-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7236 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 320,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 291,
    "static_load_kN": 375,
    "fatigue_load_limit_kN": 10,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 18000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7236 BCBM is SKF's 180 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 180×320×52 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 180×320×52 mm (7.087×12.598×2.047 in), 70.0 mm radial section height, C 291 kN, C0 375 kN, Pu 10 kN.reference speed 2,400 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 18000 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 2,600 r/min while thermal balance under catalogue load sets the 2,400 r/min reference; at dm ≈ 250.0 mm the corresponding dn is approximately 650k mm·r/min. Selection figures for 7236 BCBM: the static-to-dynamic ratio C0/C is 1.29, Pu 10 kN is about 3 % of C, and catalogue mass works out to roughly 100 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 2,400 r/min against a 2,600 r/min limiting speed, i.e. a reference-to-limit ratio of 0.92. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly m6 on a 180 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Fillet radii must clear the chamfer so the 52 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7236-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7236-BCBM?",
        "a": "7236 BCBM measures 180 mm bore × 320 mm OD × 52 mm width (7.087 × 12.598 × 2.047 in), mass about 18000 g. SKF 17000 ratings: C 291 kN, C0 375 kN, Pu 10 kN, reference speed 2,400 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7236-BCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7236",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 180×320×52 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "QJ-236-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×320×52 mm envelope, but catalogue C/C0 differ between executions (291/375 kN vs 475/765 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7236-BCBM",
      "7236 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7336-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7336 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 380,
    "B_mm": 75,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 410,
    "static_load_kN": 540,
    "fatigue_load_limit_kN": 13.7,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 42000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7336 BCBM is SKF's 180 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 180×380×75 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 180×380×75 mm (7.087×14.961×2.953 in), 100.0 mm radial section height, C 410 kN, C0 540 kN, Pu 13.7 kN.reference speed 2,000 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 42000 g. Load balance: C0 540 kN against C 410 kN gives a 1.32 ratio, typical of a steep-angle axial-oriented design; Pu 13.7 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 180 mm bore: 410 kN C divided by the 100.0 mm radial section height gives 4.1 kN per section millimetre; the 42000 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 2,000 r/min against a 2,400 r/min limiting speed, i.e. a reference-to-limit ratio of 0.83. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "hydraulic press and converter tilt drives",
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7336-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7336-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7336-BCBM?",
        "a": "7336 BCBM measures 180 mm bore × 380 mm OD × 75 mm width (7.087 × 14.961 × 2.953 in), mass about 42000 g. SKF 17000 ratings: C 410 kN, C0 540 kN, Pu 13.7 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7336-BCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7336-BCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7336",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "QJ-336-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×380×75 mm envelope, but catalogue C/C0 differ between executions (410/540 kN vs 680/1100 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7336-BCBM",
      "7336 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7038-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7038 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 290,
    "B_mm": 46,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 199,
    "static_load_kN": 255,
    "fatigue_load_limit_kN": 6.95,
    "reference_speed_rpm": 2400,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 10500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7038 BGM is SKF's 190 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 190×290×46 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 190×290×46 mm (7.48×11.417×1.811 in), 50.0 mm radial section height, C 199 kN, C0 255 kN, Pu 6.95 kN.reference speed 2,400 r/min (thermal) and limiting speed 2,400 r/min (mechanical), which coincide for this size, catalogue mass 10500 g. Envelope economics: the 46 mm width over a 50.0 mm section yields 0.92 mm of ring width per section millimetre, and the bearing weighs 10500 g for 199 kN of dynamic capacity — about 53 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 2,400 r/min while thermal balance under catalogue load sets the 2,400 r/min reference; at dm ≈ 240.0 mm the corresponding dn is approximately 576k mm·r/min. Bore-to-OD planning: OD 290 over bore 190 is a 1.53× step for this size, and the 46 mm width gives a bore/width ratio of 4.13; use these ratios when housing space around the 190 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Do not mix execution classes inside one set: a universally matchable BGM unit is ground for arbitrary pairing, a basic execution is not.",
      "Fillet radii must clear the chamfer so the 46 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7038-BGM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "The steep 40° angle of 7038-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7038 BGM as the single g brass execution; the other order numbers of the 7038 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7038-BGM?",
        "a": "7038 BGM measures 190 mm bore × 290 mm OD × 46 mm width (7.48 × 11.417 × 1.811 in), mass about 10500 g. SKF 17000 ratings: C 199 kN, C0 255 kN, Pu 6.95 kN, reference speed 2,400 r/min (thermal) and limiting speed 2,400 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7038-BGM?",
        "a": "The 2,400 r/min reference (thermal) and 2,400 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7038-BGM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7038",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 190×290×46 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7038",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7038-BGM",
      "7038 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7238-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7238 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 340,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 307,
    "static_load_kN": 405,
    "fatigue_load_limit_kN": 10.4,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 22000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7238 BCBM is SKF's 190 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 190×340×55 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 190×340×55 mm (7.48×13.386×2.165 in), 75.0 mm radial section height, C 307 kN, C0 405 kN, Pu 10.4 kN.reference speed 2,000 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 22000 g. Selection figures for 7238 BCBM: the static-to-dynamic ratio C0/C is 1.32, Pu 10.4 kN is about 3 % of C, and catalogue mass works out to roughly 116 g per millimetre of bore. At the printed limiting speed of 2,600 r/min the mean pitch diameter dm ≈ 265.0 mm implies a dn value around 689k mm·r/min; the 2,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 340 over bore 190 is a 1.79× step for this size, and the 55 mm width gives a bore/width ratio of 3.45; use these ratios when housing space around the 190 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "One 7238-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 55 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "The steep 40° angle of 7238-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7238-BCBM?",
        "a": "7238 BCBM measures 190 mm bore × 340 mm OD × 55 mm width (7.48 × 13.386 × 2.165 in), mass about 22000 g. SKF 17000 ratings: C 307 kN, C0 405 kN, Pu 10.4 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7238-BCBM?",
        "a": "The 2,000 r/min reference (thermal) and 2,600 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      },
      {
        "q": "Can one 7238-BCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7238",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "QJ-238-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×340×55 mm envelope, but catalogue C/C0 differ between executions (307/405 kN vs 510/850 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7238-BCBM",
      "7238 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7338-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7338 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 400,
    "B_mm": 78,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 442,
    "static_load_kN": 600,
    "fatigue_load_limit_kN": 14.6,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 48500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7338 BCBM is SKF's 190 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 190×400×78 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 190×400×78 mm (7.48×15.748×3.071 in), 105.0 mm radial section height, C 442 kN, C0 600 kN, Pu 14.6 kN.reference speed 2,000 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 48500 g. The 14.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 442/600 kN ratings and 48500 g mass this execution carries about 2.33 kN of C per millimetre of bore. Load balance: C0 600 kN against C 442 kN gives a 1.36 ratio, typical of a steep-angle axial-oriented design; Pu 14.6 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 400 over bore 190 is a 2.11× step for this size, and the 78 mm width gives a bore/width ratio of 2.44; use these ratios when housing space around the 190 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts",
      "hydraulic press and converter tilt drives"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "Assign interference to the rotating ring — roughly m6 on a 190 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "The steep 40° angle of 7338-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7338-BCBM?",
        "a": "7338 BCBM measures 190 mm bore × 400 mm OD × 78 mm width (7.48 × 15.748 × 3.071 in), mass about 48500 g. SKF 17000 ratings: C 442 kN, C0 600 kN, Pu 14.6 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7338-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 190 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7338",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "QJ-338-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×400×78 mm envelope, but catalogue C/C0 differ between executions (442/600 kN vs 702/1160 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7338-BCBM",
      "7338 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7040-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7040 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 310,
    "B_mm": 51,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 225,
    "static_load_kN": 290,
    "fatigue_load_limit_kN": 7.8,
    "reference_speed_rpm": 2200,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 18000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7040 BGM is SKF's 200 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 200×310×51 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 200×310×51 mm (7.874×12.205×2.008 in), 55.0 mm radial section height, C 225 kN, C0 290 kN, Pu 7.8 kN.reference speed 2,200 r/min (thermal) and limiting speed 2,200 r/min (mechanical), which coincide for this size, catalogue mass 18000 g. The 7.8 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 225/290 kN ratings and 18000 g mass this execution carries about 1.13 kN of C per millimetre of bore. Mass and section check: 18000 g inside the 200×310×51 mm outline leaves a 55.0 mm radial section, and the 290 kN static rating is 1.29× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 2,200 r/min against a 2,200 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives",
      "heavy industrial gearboxes"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BGM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "One 7040-BGM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "At 200 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Fillet radii must clear the chamfer so the 51 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7040-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7040 BGM as the single g brass execution; the other order numbers of the 7040 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7040-BGM?",
        "a": "7040 BGM measures 200 mm bore × 310 mm OD × 51 mm width (7.874 × 12.205 × 2.008 in), mass about 18000 g. SKF 17000 ratings: C 225 kN, C0 290 kN, Pu 7.8 kN, reference speed 2,200 r/min (thermal) and limiting speed 2,200 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7040-BGM?",
        "a": "With a rotating inner ring use roughly m6 on the 200 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7040",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 200×310×51 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "7040",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7040-BGM",
      "7040 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7240-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7240 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 360,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 325,
    "static_load_kN": 430,
    "fatigue_load_limit_kN": 11,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2400,
    "max_rpm": 2400,
    "weight_g": 25000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7240 BCBM is SKF's 200 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 200×360×58 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 200×360×58 mm (7.874×14.173×2.283 in), 80.0 mm radial section height, C 325 kN, C0 430 kN, Pu 11 kN.reference speed 2,000 r/min (thermal) and limiting speed 2,400 r/min (mechanical), catalogue mass 25000 g. The 11 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 325/430 kN ratings and 25000 g mass this execution carries about 1.63 kN of C per millimetre of bore. Mass and section check: 25000 g inside the 200×360×58 mm outline leaves a 80.0 mm radial section, and the 430 kN static rating is 1.32× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 2,000 r/min against a 2,400 r/min limiting speed, i.e. a reference-to-limit ratio of 0.83. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7240-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.",
      "At 200 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7240-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7240-BCBM?",
        "a": "7240 BCBM measures 200 mm bore × 360 mm OD × 58 mm width (7.874 × 14.173 × 2.283 in), mass about 25000 g. SKF 17000 ratings: C 325 kN, C0 430 kN, Pu 11 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,400 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7240-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 200 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7240",
        "equiv_brand": "NTN",
        "level": "partial",
        "note": "Same 200×360×58 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting."
      },
      {
        "equiv_sku": "QJ-240-N2MA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 200×360×58 mm envelope, but catalogue C/C0 differ between executions (325/430 kN vs 540/915 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7240-BCBM",
      "7240 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7340-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7340 BCBM",
    "series": "7300-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 420,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 462,
    "static_load_kN": 655,
    "fatigue_load_limit_kN": 15.6,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 53000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7340 BCBM is SKF's 200 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 200×420×80 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 200×420×80 mm (7.874×16.535×3.15 in), 110.0 mm radial section height, C 462 kN, C0 655 kN, Pu 15.6 kN.reference speed 1,900 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 53000 g. Selection figures for 7340 BCBM: the static-to-dynamic ratio C0/C is 1.42, Pu 15.6 kN is about 3 % of C, and catalogue mass works out to roughly 265 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 2,200 r/min while thermal balance under catalogue load sets the 1,900 r/min reference; at dm ≈ 310.0 mm the corresponding dn is approximately 682k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 1,900 r/min against a 2,200 r/min limiting speed, i.e. a reference-to-limit ratio of 0.86. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives",
      "heavy industrial gearboxes"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.",
      "One 7340-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7340-BCBM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "One 7340-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "The steep 40° angle of 7340-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7340-BCBM?",
        "a": "7340 BCBM measures 200 mm bore × 420 mm OD × 80 mm width (7.874 × 16.535 × 3.15 in), mass about 53000 g. SKF 17000 ratings: C 462 kN, C0 655 kN, Pu 15.6 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What minimum axial load does 7340-BCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7340",
        "equiv_brand": "NTN",
        "level": "full",
        "note": "Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier."
      },
      {
        "equiv_sku": "7340",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7340-BCBM",
      "7340 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7044-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7044 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 220,
    "D_mm": 340,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 255,
    "static_load_kN": 355,
    "fatigue_load_limit_kN": 9,
    "reference_speed_rpm": 2000,
    "limiting_speed_rpm": 2000,
    "max_rpm": 2000,
    "weight_g": 18000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7044 BGM is SKF's 220 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 220×340×56 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 220×340×56 mm (8.661×13.386×2.205 in), 60.0 mm radial section height, C 255 kN, C0 355 kN, Pu 9 kN.reference speed 2,000 r/min (thermal) and limiting speed 2,000 r/min (mechanical), which coincide for this size, catalogue mass 18000 g. Sizing arithmetic on the 220 mm bore: 255 kN C divided by the 60.0 mm radial section height gives 4.3 kN per section millimetre; the 18000 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 355 kN against C 255 kN gives a 1.39 ratio, typical of a steep-angle axial-oriented design; Pu 9 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 2,000 r/min against a 2,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "At 220 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7044-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7044 BGM as the single g brass execution; the other order numbers of the 7044 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7044-BGM?",
        "a": "7044 BGM measures 220 mm bore × 340 mm OD × 56 mm width (8.661 × 13.386 × 2.205 in), mass about 18000 g. SKF 17000 ratings: C 255 kN, C0 355 kN, Pu 9 kN, reference speed 2,000 r/min (thermal) and limiting speed 2,000 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Can one 7044-BGM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7044-BGM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7044",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7044-BGM",
      "7044 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7244-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7244 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 220,
    "D_mm": 400,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 390,
    "static_load_kN": 560,
    "fatigue_load_limit_kN": 13.4,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 2200,
    "max_rpm": 2200,
    "weight_g": 37000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7244 BCBM is SKF's 220 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 220×400×65 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 220×400×65 mm (8.661×15.748×2.559 in), 90.0 mm radial section height, C 390 kN, C0 560 kN, Pu 13.4 kN.reference speed 1,900 r/min (thermal) and limiting speed 2,200 r/min (mechanical), catalogue mass 37000 g. Sizing arithmetic on the 220 mm bore: 390 kN C divided by the 90.0 mm radial section height gives 4.3 kN per section millimetre; the 37000 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 560 kN against C 390 kN gives a 1.44 ratio, typical of a steep-angle axial-oriented design; Pu 13.4 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 1,900 r/min against a 2,200 r/min limiting speed, i.e. a reference-to-limit ratio of 0.86. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "mineral-processing and crusher drives",
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts"
    ],
    "failure_modes": [
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Fillet radii must clear the chamfer so the 65 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "One 7244-BCBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7244-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7244-BCBM?",
        "a": "7244 BCBM measures 220 mm bore × 400 mm OD × 65 mm width (8.661 × 15.748 × 2.559 in), mass about 37000 g. SKF 17000 ratings: C 390 kN, C0 560 kN, Pu 13.4 kN, reference speed 1,900 r/min (thermal) and limiting speed 2,200 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which grease and fill for 7244-BCBM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 2,200 r/min ceiling."
      },
      {
        "q": "What do the reference and limiting speeds mean for 7244-BCBM?",
        "a": "The 1,900 r/min reference (thermal) and 2,200 r/min limiting (mechanical) speeds are catalogue conditions; preload, lubrication and heat removal move the permissible value, so re-calculate for the actual arrangement."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7244",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7244-BCBM",
      "7244 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7048-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7048 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 240,
    "D_mm": 360,
    "B_mm": 56,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 260,
    "static_load_kN": 375,
    "fatigue_load_limit_kN": 9.15,
    "reference_speed_rpm": 1900,
    "limiting_speed_rpm": 1900,
    "max_rpm": 1900,
    "weight_g": 19000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7048 BGM is SKF's 240 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 240×360×56 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 240×360×56 mm (9.449×14.173×2.205 in), 60.0 mm radial section height, C 260 kN, C0 375 kN, Pu 9.15 kN.reference speed 1,900 r/min (thermal) and limiting speed 1,900 r/min (mechanical), which coincide for this size, catalogue mass 19000 g. The 9.15 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 260/375 kN ratings and 19000 g mass this execution carries about 1.08 kN of C per millimetre of bore. Mass and section check: 19000 g inside the 240×360×56 mm outline leaves a 60.0 mm radial section, and the 375 kN static rating is 1.44× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 1,900 r/min against a 1,900 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "wind-turbine gearbox shafts",
      "rolling-mill auxiliary drives",
      "mineral-processing and crusher drives"
    ],
    "failure_modes": [
      "fretting at the ground set faces of a universal pair whose clamp torque relaxes",
      "raceway spalling from axial overload beyond the single-direction thrust rating",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Mount by induction-heating the inner ring to max 120 °C; driving the bearing home through the outer ring or balls brinells the asymmetric raceway.",
      "One 7048-BGM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.",
      "Fillet radii must clear the chamfer so the 56 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "The steep 40° angle of 7048-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7048 BGM as the single g brass execution; the other order numbers of the 7048 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7048-BGM?",
        "a": "7048 BGM measures 240 mm bore × 360 mm OD × 56 mm width (9.449 × 14.173 × 2.205 in), mass about 19000 g. SKF 17000 ratings: C 260 kN, C0 375 kN, Pu 9.15 kN, reference speed 1,900 r/min (thermal) and limiting speed 1,900 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Can one 7048-BGM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7048-BGM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7048",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7048-BGM",
      "7048 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7248-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7248 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 240,
    "D_mm": 440,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 449,
    "static_load_kN": 670,
    "fatigue_load_limit_kN": 15.3,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 49000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7248 BCBM is SKF's 240 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 240×440×72 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 240×440×72 mm (9.449×17.323×2.835 in), 100.0 mm radial section height, C 449 kN, C0 670 kN, Pu 15.3 kN.reference speed 1,600 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 49000 g. The 15.3 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 449/670 kN ratings and 49000 g mass this execution carries about 1.87 kN of C per millimetre of bore. Mass and section check: 49000 g inside the 240×440×72 mm outline leaves a 100.0 mm radial section, and the 670 kN static rating is 1.49× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 1,600 r/min against a 2,600 r/min limiting speed, i.e. a reference-to-limit ratio of 0.62. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts",
      "hydraulic press and converter tilt drives"
    ],
    "failure_modes": [
      "false brinelling on idle paired sets exposed to machine vibration",
      "contact-angle shift and edge loading after uneven locknut torque tilts the set",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 72 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Assign interference to the rotating ring — roughly m6 on a 240 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "The steep 40° angle of 7248-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7248-BCBM?",
        "a": "7248 BCBM measures 240 mm bore × 440 mm OD × 72 mm width (9.449 × 17.323 × 2.835 in), mass about 49000 g. SKF 17000 ratings: C 449 kN, C0 670 kN, Pu 15.3 kN, reference speed 1,600 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7248-BCBM?",
        "a": "With a rotating inner ring use roughly m6 on the 240 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7248",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7248-BCBM",
      "7248 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7052-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7052 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 260,
    "D_mm": 400,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 332,
    "static_load_kN": 510,
    "fatigue_load_limit_kN": 11.8,
    "reference_speed_rpm": 1700,
    "limiting_speed_rpm": 1700,
    "max_rpm": 1700,
    "weight_g": 30000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7052 BGM is SKF's 260 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 260×400×65 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 260×400×65 mm (10.236×15.748×2.559 in), 70.0 mm radial section height, C 332 kN, C0 510 kN, Pu 11.8 kN.reference speed 1,700 r/min (thermal) and limiting speed 1,700 r/min (mechanical), which coincide for this size, catalogue mass 30000 g. Selection figures for 7052 BGM: the static-to-dynamic ratio C0/C is 1.54, Pu 11.8 kN is about 4 % of C, and catalogue mass works out to roughly 115 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 1,700 r/min while thermal balance under catalogue load sets the 1,700 r/min reference; at dm ≈ 330.0 mm the corresponding dn is approximately 561k mm·r/min. Bore-to-OD planning: OD 400 over bore 260 is a 1.54× step for this size, and the 65 mm width gives a bore/width ratio of 4.00; use these ratios when housing space around the 260 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "heavy industrial gearboxes",
      "large process pumps and compressors",
      "marine propulsion and deck machinery"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.",
      "Assign interference to the rotating ring — roughly m6 on a 260 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Fillet radii must clear the chamfer so the 65 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Do not mix execution classes inside one set: a universally matchable BGM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7052-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7052 BGM as the single g brass execution; the other order numbers of the 7052 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7052-BGM?",
        "a": "7052 BGM measures 260 mm bore × 400 mm OD × 65 mm width (10.236 × 15.748 × 2.559 in), mass about 30000 g. SKF 17000 ratings: C 332 kN, C0 510 kN, Pu 11.8 kN, reference speed 1,700 r/min (thermal) and limiting speed 1,700 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Which fits should I use for 7052-BGM?",
        "a": "With a rotating inner ring use roughly m6 on the 260 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7052-BGM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 1,700 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7052",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7052-BGM",
      "7052 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7056-BGM",
    "brand": "SKF",
    "manufacturer_designation": "7056 BGM",
    "series": "7000-series",
    "type": "angular_contact",
    "d_mm": 280,
    "D_mm": 420,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 338,
    "static_load_kN": 540,
    "fatigue_load_limit_kN": 12.2,
    "reference_speed_rpm": 1600,
    "limiting_speed_rpm": 1600,
    "max_rpm": 1600,
    "weight_g": 30000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7056 BGM is SKF's 280 mm-bore single-row angular-contact ball bearing in the 7000 series, nominal 40° (B) contact angle, 280×420×65 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set. Envelope 280×420×65 mm (11.024×16.535×2.559 in), 70.0 mm radial section height, C 338 kN, C0 540 kN, Pu 12.2 kN.reference speed 1,600 r/min (thermal) and limiting speed 1,600 r/min (mechanical), which coincide for this size, catalogue mass 30000 g. Envelope economics: the 65 mm width over a 70.0 mm section yields 0.93 mm of ring width per section millimetre, and the bearing weighs 30000 g for 338 kN of dynamic capacity — about 89 g per rated kN. At the printed limiting speed of 1,600 r/min the mean pitch diameter dm ≈ 350.0 mm implies a dn value around 560k mm·r/min; the 1,600 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 420 over bore 280 is a 1.50× step for this size, and the 65 mm width gives a bore/width ratio of 4.31; use these ratios when housing space around the 280 mm shaft is the first constraint. Large-bore universal execution: the G suffix marks a universally matchable bearing delivered with controlled axial internal clearance rather than a factory preload, paired here with a machined brass cage (M); BGM is the large-section 70xx/72xx/73xx answer where field-set preload and brass-cage robustness are both required.",
    "applications": [
      "hydraulic press and converter tilt drives",
      "heavy dredge and excavator swing drives",
      "vertical mill separator drives"
    ],
    "failure_modes": [
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "false brinelling on idle paired sets exposed to machine vibration",
      "ball skidding when Fa/Fr stays below the 1,0 (40°) or 0,55 (25°) ratio and the contact ellipse is unloaded",
      "G-clearance drift in a large-bore set whose stand-off rings settle under sustained heavy thrust",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Greased positions should fill roughly 25–35 % of the free volume on a 7056-BGM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Greased positions should fill roughly 25–35 % of the free volume on a 7056-BGM of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.",
      "Fillet radii must clear the chamfer so the 65 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BGM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "The steep 40° angle of 7056-BGM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7056 BGM as the single g brass execution; the other order numbers of the 7056 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7056-BGM?",
        "a": "7056 BGM measures 280 mm bore × 420 mm OD × 65 mm width (11.024 × 16.535 × 2.559 in), mass about 30000 g. SKF 17000 ratings: C 338 kN, C0 540 kN, Pu 12.2 kN, reference speed 1,600 r/min (thermal) and limiting speed 1,600 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BGM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. G marks a universally matchable bearing delivered with axial internal clearance (rather than factory preload), the starting point for field-set preload in a DB/DF set."
      },
      {
        "q": "Which fits should I use for 7056-BGM?",
        "a": "With a rotating inner ring use roughly m6 on the 280 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      },
      {
        "q": "Which grease and fill for 7056-BGM?",
        "a": "A premium mineral-oil grease with polyurea or lithium complex thickener and NLGI 2 consistency suits normal operating temperature; fill roughly 25–35 % of the free volume. Oil-air or oil-jet lubrication is the choice near the 1,600 r/min ceiling."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7056",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7056-BGM",
      "7056 BGM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7256-BM",
    "brand": "SKF",
    "manufacturer_designation": "7256 BM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 280,
    "D_mm": 500,
    "B_mm": 80,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 507,
    "static_load_kN": 830,
    "fatigue_load_limit_kN": 17.6,
    "reference_speed_rpm": 1400,
    "limiting_speed_rpm": 1400,
    "max_rpm": 1400,
    "weight_g": 67500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7256 BM is SKF's 280 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 280×500×80 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.. Envelope 280×500×80 mm (11.024×19.685×3.15 in), 110.0 mm radial section height, C 507 kN, C0 830 kN, Pu 17.6 kN.reference speed 1,400 r/min (thermal) and limiting speed 1,400 r/min (mechanical), which coincide for this size, catalogue mass 67500 g. Mass and section check: 67500 g inside the 280×500×80 mm outline leaves a 110.0 mm radial section, and the 830 kN static rating is 1.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 830 kN against C 507 kN gives a 1.64 ratio, typical of a steep-angle axial-oriented design; Pu 17.6 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 1,400 r/min against a 1,400 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00. Non-optimized basic execution: BM is the earlier 40-degree design without the E internal upgrade, fitted with a machined brass ball-centred cage as a single (non-universal) bearing; quote it for housings and spacers designed around the legacy geometry.",
    "applications": [
      "sugar mill and cement kiln pinion shafts",
      "hydraulic press and converter tilt drives",
      "heavy dredge and excavator swing drives"
    ],
    "failure_modes": [
      "ball skidding when the induced axial load unloads the inactive bearing of a pair",
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "legacy-geometry cage smearing when the non-E basic bearing is run at speeds developed for the optimized E design",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Fillet radii must clear the chamfer so the 80 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.",
      "At 280 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "At 280 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "Do not mix execution classes inside one set: a universally matchable BM unit is ground for arbitrary pairing, a basic execution is not.",
      "The steep 40° angle of 7256-BM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 7256 BM as the single non e brass execution; the other order numbers of the 7256 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7256-BM?",
        "a": "7256 BM measures 280 mm bore × 500 mm OD × 80 mm width (11.024 × 19.685 × 3.15 in), mass about 67500 g. SKF 17000 ratings: C 507 kN, C0 830 kN, Pu 17.6 kN, reference speed 1,400 r/min (thermal) and limiting speed 1,400 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. The BM is the non-optimized basic 40° execution with a machined brass cage; it predates the E geometry and is stocked for positions built around its specific figures.."
      },
      {
        "q": "What is the difference between BEP, BECBP and BECBM?",
        "a": "All share the 40° optimized geometry: BEP is the basic PA66-caged single bearing, BECBP adds CB universal matching (ground faces, Normal clearance) with the same PA66 cage, and BECBM is the universally matchable version with a machined brass cage for higher speed and temperature."
      },
      {
        "q": "Which fits should I use for 7256-BM?",
        "a": "With a rotating inner ring use roughly m6 on the 280 mm shaft and H7 in the housing; give the stationary ring a slide fit for axial setting, and reverse the logic when the outer ring rotates."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7256",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7256-BM",
      "7256 BM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "7260-BCBM",
    "brand": "SKF",
    "manufacturer_designation": "7260 BCBM",
    "series": "7200-series",
    "type": "angular_contact",
    "d_mm": 300,
    "D_mm": 540,
    "B_mm": 85,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 553,
    "static_load_kN": 930,
    "fatigue_load_limit_kN": 19.3,
    "reference_speed_rpm": 1300,
    "limiting_speed_rpm": 1300,
    "max_rpm": 1300,
    "weight_g": 85000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "7260 BCBM is SKF's 300 mm-bore single-row angular-contact ball bearing in the 7200 series, nominal 40° (B) contact angle, 300×540×85 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 300×540×85 mm (11.811×21.26×3.346 in), 120.0 mm radial section height, C 553 kN, C0 930 kN, Pu 19.3 kN.reference speed 1,300 r/min (thermal) and limiting speed 1,300 r/min (mechanical), which coincide for this size, catalogue mass 85000 g. Load balance: C0 930 kN against C 553 kN gives a 1.68 ratio, typical of a steep-angle axial-oriented design; Pu 19.3 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 300 mm bore: 553 kN C divided by the 120.0 mm radial section height gives 4.6 kN per section millimetre; the 85000 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 540 over bore 300 is a 1.80× step for this size, and the 85 mm width gives a bore/width ratio of 3.53; use these ratios when housing space around the 300 mm shaft is the first constraint. Non-optimized universal execution: BCBM keeps the earlier internal geometry (no E) with CB Normal-clearance set mounting and a machined brass ball-centred cage; it is stocked for positions built around its established ratings rather than the enhanced E ball complement.",
    "applications": [
      "large mud pumps and offshore winch drums",
      "sugar mill and cement kiln pinion shafts",
      "hydraulic press and converter tilt drives"
    ],
    "failure_modes": [
      "preload loss as a loosely clamped set runs slack and the balls smear the raceways",
      "thermal preload runaway in a back-to-back pair when inner-ring heat cannot expand away",
      "raceway smearing under minimum-axial-load starvation at light load and high speed",
      "set preload miscalculation because the non-E BCBM geometry differs in stiffness from E executions despite matching CB faces",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Assign interference to the rotating ring — roughly m6 on a 300 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.",
      "Preload the set against a calculated stand-off dimension — the ground faces of BCBM establish it, but locknut torque, sleeve crush and housing-face squareness each consume part of the allowance.",
      "Do not mix execution classes inside one set: a universally matchable BCBM unit is ground for arbitrary pairing, a basic execution is not.",
      "At 300 mm bore the m6 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.",
      "The steep 40° angle of 7260-BCBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.",
      "Universally matchable BCBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 7260-BCBM?",
        "a": "7260 BCBM measures 300 mm bore × 540 mm OD × 85 mm width (11.811 × 21.26 × 3.346 in), mass about 85000 g. SKF 17000 ratings: C 553 kN, C0 930 kN, Pu 19.3 kN, reference speed 1,300 r/min (thermal) and limiting speed 1,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the BCBM suffix mean?",
        "a": "40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Can one 7260-BCBM take thrust in both directions?",
        "a": "No. A single-row angular-contact bearing reacts axial load in one direction; reversing thrust needs a DB/DF matched pair (use a universally matchable CB/GA execution) or a double-row bearing. Under radial load the 40° angle induces an axial force that the arrangement must balance."
      },
      {
        "q": "What minimum axial load does 7260-BCBM need?",
        "a": "The balls must remain seated: SKF gives Fam ≈ A·(n·dm/1000)² and a load-ratio guideline of Fa/Fr ≥ 1 for the 40° B execution and ≥ 0,55 for the 25° AC execution. Preloaded pairs and spring loading are the usual ways of meeting it at light load and high speed."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7260",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "7260-BCBM",
      "7260 BCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3200-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3200 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 7.61,
    "static_load_kN": 4.3,
    "fatigue_load_limit_kN": 0.183,
    "reference_speed_rpm": 26000,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 51,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3200 ATN9 is SKF's 10 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 10×30×14 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 10×30×14 mm (0.394×1.181×0.551 in), 10.0 mm radial section height, C 7.61 kN, C0 4.3 kN, Pu 0.183 kN.reference speed 26,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical), catalogue mass 51 g. The 0.183 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 7.61/4.3 kN ratings and 51 g mass this execution carries about 0.76 kN of C per millimetre of bore. Load balance: C0 4.3 kN against C 7.61 kN gives a 0.57 ratio, typical of a double-row bidirectional design; Pu 0.183 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 30 over bore 10 is a 3.00× step for this size, and the 14 mm width gives a bore/width ratio of 0.71; use these ratios when housing space around the 10 mm shaft is the first constraint.",
    "applications": [
      "small double-supported gear shafts needing two-direction location in one bearing",
      "compact pump and compressor drives",
      "textile machinery roller drives"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "A capped 3200-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "A capped 3200-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3200 ATN9 as the double atn9 execution; the other order numbers of the 3200 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3200-ATN9?",
        "a": "3200 ATN9 measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 51 g. SKF 17000 ratings: C 7.61 kN, C0 4.3 kN, Pu 0.183 kN, reference speed 26,000 r/min (thermal) and limiting speed 24,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Does the 3200 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly j5 on the 10 mm shaft and H7 in the 30 mm housing; check the wide ring seats square because the 14 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3200-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×14 mm envelope with catalogue ratings within 10 %; 3200 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3200-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×14 mm envelope with catalogue ratings within 10 %; 3200 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3200-ATN9",
      "3200 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3201-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3201 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 10.1,
    "static_load_kN": 5.6,
    "fatigue_load_limit_kN": 0.24,
    "reference_speed_rpm": 24000,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 58,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3201 ATN9 is SKF's 12 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 12×32×15.9 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 12×32×15.9 mm (0.472×1.26×0.626 in), 10.0 mm radial section height, C 10.1 kN, C0 5.6 kN, Pu 0.24 kN.reference speed 24,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical), catalogue mass 58 g. Selection figures for 3201 ATN9: the static-to-dynamic ratio C0/C is 0.55, Pu 0.24 kN is about 2 % of C, and catalogue mass works out to roughly 5 g per millimetre of bore. At the printed limiting speed of 22,000 r/min the mean pitch diameter dm ≈ 22.0 mm implies a dn value around 484k mm·r/min; the 24,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 32 over bore 12 is a 2.67× step for this size, and the 15.9 mm width gives a bore/width ratio of 0.75; use these ratios when housing space around the 12 mm shaft is the first constraint.",
    "applications": [
      "compact pump and compressor drives",
      "textile machinery roller drives",
      "small two-bearing-housing arrangements"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "A capped 3201-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings of 10.1/5.6 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3201 ATN9 as the double atn9 execution; the other order numbers of the 3201 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3201-ATN9?",
        "a": "3201 ATN9 measures 12 mm bore × 32 mm OD × 15.9 mm width (0.472 × 1.26 × 0.626 in), mass about 58 g. SKF 17000 ratings: C 10.1 kN, C0 5.6 kN, Pu 0.24 kN, reference speed 24,000 r/min (thermal) and limiting speed 22,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly j5 on the 12 mm shaft and H7 in the 32 mm housing; check the wide ring seats square because the 15.9 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3201 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3201-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×15.9 mm envelope with catalogue ratings within 10 %; 3201 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3201-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×15.9 mm envelope with catalogue ratings within 10 %; 3201 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3201-ATN9",
      "3201 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3202-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3202 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 11.2,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.285,
    "reference_speed_rpm": 22000,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 66,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3202 ATN9 is SKF's 15 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 15×35×15.9 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 15×35×15.9 mm (0.591×1.378×0.626 in), 10.0 mm radial section height, C 11.2 kN, C0 6.8 kN, Pu 0.285 kN.reference speed 22,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical), catalogue mass 66 g. Load balance: C0 6.8 kN against C 11.2 kN gives a 0.61 ratio, typical of a double-row bidirectional design; Pu 0.285 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 15 mm bore: 11.2 kN C divided by the 10.0 mm radial section height gives 1.1 kN per section millimetre; the 66 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 22,000 r/min against a 18,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.22.",
    "applications": [
      "textile machinery roller drives",
      "small two-bearing-housing arrangements",
      "small double-supported gear shafts needing two-direction location in one bearing"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3202 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Interference goes on the rotating ring (about j5 at 15 mm bore); the wide 15.9 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "A capped 3202-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings of 11.2/6.8 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3202 ATN9 as the double atn9 execution; the other order numbers of the 3202 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3202-ATN9?",
        "a": "3202 ATN9 measures 15 mm bore × 35 mm OD × 15.9 mm width (0.591 × 1.378 × 0.626 in), mass about 66 g. SKF 17000 ratings: C 11.2 kN, C0 6.8 kN, Pu 0.285 kN, reference speed 22,000 r/min (thermal) and limiting speed 18,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Why choose the double-row 3202 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3202-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×15.9 mm envelope with catalogue ratings within 10 %; 3202 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3202-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×15.9 mm envelope with catalogue ratings within 10 %; 3202 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3202-ATN9",
      "3202 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3302-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3302 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 15.1,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "reference_speed_rpm": 18000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3302 ATN9 is SKF's 15 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 15×42×19 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 15×42×19 mm (0.591×1.654×0.748 in), 13.5 mm radial section height, C 15.1 kN, C0 9.3 kN, Pu 0.4 kN.reference speed 18,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical), catalogue mass 130 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 16,000 r/min while thermal balance under catalogue load sets the 18,000 r/min reference; at dm ≈ 28.5 mm the corresponding dn is approximately 456k mm·r/min. Selection figures for 3302 ATN9: the static-to-dynamic ratio C0/C is 0.62, Pu 0.4 kN is about 3 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 18,000 r/min against a 16,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.13.",
    "applications": [
      "small two-bearing-housing arrangements",
      "small double-supported gear shafts needing two-direction location in one bearing",
      "compact pump and compressor drives"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about j5 at 15 mm bore); the wide 19 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings of 15.1/9.3 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "A capped 3302-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The double-row 3302 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3302 ATN9 as the double atn9 execution; the other order numbers of the 3302 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3302-ATN9?",
        "a": "3302 ATN9 measures 15 mm bore × 42 mm OD × 19 mm width (0.591 × 1.654 × 0.748 in), mass about 130 g. SKF 17000 ratings: C 15.1 kN, C0 9.3 kN, Pu 0.4 kN, reference speed 18,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3302 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3302-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×19 mm envelope with catalogue ratings within 10 %; 3302 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3302-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×19 mm envelope with catalogue ratings within 10 %; 3302 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3302-ATN9",
      "3302 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3203-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3203 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.8,
    "fatigue_load_limit_kN": 0.365,
    "reference_speed_rpm": 19000,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 96,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3203 ATN9 is SKF's 17 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 17×40×17.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 17×40×17.5 mm (0.669×1.575×0.689 in), 11.5 mm radial section height, C 14.3 kN, C0 8.8 kN, Pu 0.365 kN.reference speed 19,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical), catalogue mass 96 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 16,000 r/min while thermal balance under catalogue load sets the 19,000 r/min reference; at dm ≈ 28.5 mm the corresponding dn is approximately 456k mm·r/min. Selection figures for 3203 ATN9: the static-to-dynamic ratio C0/C is 0.62, Pu 0.365 kN is about 3 % of C, and catalogue mass works out to roughly 6 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 19,000 r/min against a 16,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.19.",
    "applications": [
      "small two-bearing-housing arrangements",
      "small double-supported gear shafts needing two-direction location in one bearing",
      "compact pump and compressor drives"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The double-row 3203 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings of 14.3/8.8 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Compared with a single-row pair of the same bore, the double-row 3203 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3203 ATN9 as the double atn9 execution; the other order numbers of the 3203 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3203-ATN9?",
        "a": "3203 ATN9 measures 17 mm bore × 40 mm OD × 17.5 mm width (0.669 × 1.575 × 0.689 in), mass about 96 g. SKF 17000 ratings: C 14.3 kN, C0 8.8 kN, Pu 0.365 kN, reference speed 19,000 r/min (thermal) and limiting speed 16,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3203 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3203-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×17.5 mm envelope with catalogue ratings within 10 %; 3203 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3203-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×17.5 mm envelope with catalogue ratings within 10 %; 3203 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3203-ATN9",
      "3203 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3303-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3303 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 12.7,
    "fatigue_load_limit_kN": 0.54,
    "reference_speed_rpm": 17000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3303 ATN9 is SKF's 17 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 17×47×22.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 17×47×22.2 mm (0.669×1.85×0.874 in), 15.0 mm radial section height, C 21.6 kN, C0 12.7 kN, Pu 0.54 kN.reference speed 17,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 180 g. Load balance: C0 12.7 kN against C 21.6 kN gives a 0.59 ratio, typical of a double-row bidirectional design; Pu 0.54 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 17 mm bore: 21.6 kN C divided by the 15.0 mm radial section height gives 1.4 kN per section millimetre; the 180 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 17,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.21.",
    "applications": [
      "textile machinery roller drives",
      "small two-bearing-housing arrangements",
      "small double-supported gear shafts needing two-direction location in one bearing"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Catalogue ratings of 21.6/12.7 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Compared with a single-row pair of the same bore, the double-row 3303 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3303-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3303 ATN9 as the double atn9 execution; the other order numbers of the 3303 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3303-ATN9?",
        "a": "3303 ATN9 measures 17 mm bore × 47 mm OD × 22.2 mm width (0.669 × 1.85 × 0.874 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 12.7 kN, Pu 0.54 kN, reference speed 17,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Why choose the double-row 3303 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3303-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×22.2 mm envelope with catalogue ratings within 10 %; 3303 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3303-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×22.2 mm envelope with catalogue ratings within 10 %; 3303 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3303-ATN9",
      "3303 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3204-A",
    "brand": "SKF",
    "manufacturer_designation": "3204 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 12.9,
    "fatigue_load_limit_kN": 0.55,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3204 A is SKF's 20 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 20×47×20.6 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 20×47×20.6 mm (0.787×1.85×0.811 in), 13.5 mm radial section height, C 20.4 kN, C0 12.9 kN, Pu 0.55 kN.reference speed 16,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 160 g. Sizing arithmetic on the 20 mm bore: 20.4 kN C divided by the 13.5 mm radial section height gives 1.5 kN per section millimetre; the 160 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 12.9 kN against C 20.4 kN gives a 0.63 ratio, typical of a double-row bidirectional design; Pu 0.55 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 16,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.14.",
    "applications": [
      "small double-supported gear shafts needing two-direction location in one bearing",
      "compact pump and compressor drives",
      "textile machinery roller drives"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Catalogue ratings of 20.4/12.9 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Interference goes on the rotating ring (about k5 at 20 mm bore); the wide 20.6 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The double-row 3204 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3204 A as the double a steel execution; the other order numbers of the 3204 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3204-A?",
        "a": "3204 A measures 20 mm bore × 47 mm OD × 20.6 mm width (0.787 × 1.85 × 0.811 in), mass about 160 g. SKF 17000 ratings: C 20.4 kN, C0 12.9 kN, Pu 0.55 kN, reference speed 16,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3204 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 20 mm shaft and H7 in the 47 mm housing; check the wide ring seats square because the 20.6 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3204-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3204-A",
      "3204 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3204-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3204 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 12.9,
    "fatigue_load_limit_kN": 0.55,
    "reference_speed_rpm": 16000,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3204 ATN9 is SKF's 20 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 20×47×20.6 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 20×47×20.6 mm (0.787×1.85×0.811 in), 13.5 mm radial section height, C 20.4 kN, C0 12.9 kN, Pu 0.55 kN.reference speed 16,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 160 g. Sizing arithmetic on the 20 mm bore: 20.4 kN C divided by the 13.5 mm radial section height gives 1.5 kN per section millimetre; the 160 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 160 g inside the 20×47×20.6 mm outline leaves a 13.5 mm radial section, and the 12.9 kN static rating is 0.63× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 47 over bore 20 is a 2.35× step for this size, and the 20.6 mm width gives a bore/width ratio of 0.97; use these ratios when housing space around the 20 mm shaft is the first constraint.",
    "applications": [
      "small double-supported gear shafts needing two-direction location in one bearing",
      "compact pump and compressor drives",
      "textile machinery roller drives"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "A capped 3204-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings of 20.4/12.9 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3204 ATN9 as the double atn9 execution; the other order numbers of the 3204 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3204-ATN9?",
        "a": "3204 ATN9 measures 20 mm bore × 47 mm OD × 20.6 mm width (0.787 × 1.85 × 0.811 in), mass about 160 g. SKF 17000 ratings: C 20.4 kN, C0 12.9 kN, Pu 0.55 kN, reference speed 16,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Does the 3204 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 20 mm shaft and H7 in the 47 mm housing; check the wide ring seats square because the 20.6 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3204-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3204-ATN9",
      "3204 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3304-A",
    "brand": "SKF",
    "manufacturer_designation": "3304 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 23.6,
    "static_load_kN": 14.6,
    "fatigue_load_limit_kN": 0.62,
    "reference_speed_rpm": 15000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3304 A is SKF's 20 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 20×52×22.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 20×52×22.2 mm (0.787×2.047×0.874 in), 16.0 mm radial section height, C 23.6 kN, C0 14.6 kN, Pu 0.62 kN.reference speed 15,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 220 g. Envelope economics: the 22.2 mm width over a 16.0 mm section yields 1.39 mm of ring width per section millimetre, and the bearing weighs 220 g for 23.6 kN of dynamic capacity — about 9 g per rated kN. At the printed limiting speed of 13,000 r/min the mean pitch diameter dm ≈ 36.0 mm implies a dn value around 468k mm·r/min; the 15,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 15,000 r/min against a 13,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.15.",
    "applications": [
      "compact pump and compressor drives",
      "textile machinery roller drives",
      "small two-bearing-housing arrangements"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The double-row 3304 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Interference goes on the rotating ring (about k5 at 20 mm bore); the wide 22.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3304 A as the double a steel execution; the other order numbers of the 3304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3304-A?",
        "a": "3304 A measures 20 mm bore × 52 mm OD × 22.2 mm width (0.787 × 2.047 × 0.874 in), mass about 220 g. SKF 17000 ratings: C 23.6 kN, C0 14.6 kN, Pu 0.62 kN, reference speed 15,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 20 mm shaft and H7 in the 52 mm housing; check the wide ring seats square because the 22.2 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3304 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3304-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3304-A",
      "3304 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3304-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3304 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 23.6,
    "static_load_kN": 14.6,
    "fatigue_load_limit_kN": 0.62,
    "reference_speed_rpm": 15000,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3304 ATN9 is SKF's 20 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 20×52×22.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 20×52×22.2 mm (0.787×2.047×0.874 in), 16.0 mm radial section height, C 23.6 kN, C0 14.6 kN, Pu 0.62 kN.reference speed 15,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical), catalogue mass 220 g. Envelope economics: the 22.2 mm width over a 16.0 mm section yields 1.39 mm of ring width per section millimetre, and the bearing weighs 220 g for 23.6 kN of dynamic capacity — about 9 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 13,000 r/min while thermal balance under catalogue load sets the 15,000 r/min reference; at dm ≈ 36.0 mm the corresponding dn is approximately 468k mm·r/min. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 22.2 mm width gives a bore/width ratio of 0.90; use these ratios when housing space around the 20 mm shaft is the first constraint.",
    "applications": [
      "compact pump and compressor drives",
      "textile machinery roller drives",
      "small two-bearing-housing arrangements"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 20 mm bore); the wide 22.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Interference goes on the rotating ring (about k5 at 20 mm bore); the wide 22.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3304 ATN9 as the double atn9 execution; the other order numbers of the 3304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3304-ATN9?",
        "a": "3304 ATN9 measures 20 mm bore × 52 mm OD × 22.2 mm width (0.787 × 2.047 × 0.874 in), mass about 220 g. SKF 17000 ratings: C 23.6 kN, C0 14.6 kN, Pu 0.62 kN, reference speed 15,000 r/min (thermal) and limiting speed 13,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 20 mm shaft and H7 in the 52 mm housing; check the wide ring seats square because the 22.2 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3304 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3304-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3304-ATN9",
      "3304 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3205-A",
    "brand": "SKF",
    "manufacturer_designation": "3205 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.6,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3205 A is SKF's 25 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 25×52×20.6 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 25×52×20.6 mm (0.984×2.047×0.811 in), 13.5 mm radial section height, C 21.6 kN, C0 14.3 kN, Pu 0.6 kN.reference speed 14,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 180 g. Envelope economics: the 20.6 mm width over a 13.5 mm section yields 1.53 mm of ring width per section millimetre, and the bearing weighs 180 g for 21.6 kN of dynamic capacity — about 8 g per rated kN. At the printed limiting speed of 12,000 r/min the mean pitch diameter dm ≈ 38.5 mm implies a dn value around 462k mm·r/min; the 14,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 14,000 r/min against a 12,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.17.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3205 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Compared with a single-row pair of the same bore, the double-row 3205 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The double-row 3205 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3205 A as the double a steel execution; the other order numbers of the 3205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3205-A?",
        "a": "3205 A measures 25 mm bore × 52 mm OD × 20.6 mm width (0.984 × 2.047 × 0.811 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 14.3 kN, Pu 0.6 kN, reference speed 14,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the 52 mm housing; check the wide ring seats square because the 20.6 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3205 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3205-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3205-A",
      "3205 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3205-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3205 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.6,
    "reference_speed_rpm": 14000,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3205 ATN9 is SKF's 25 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 25×52×20.6 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 25×52×20.6 mm (0.984×2.047×0.811 in), 13.5 mm radial section height, C 21.6 kN, C0 14.3 kN, Pu 0.6 kN.reference speed 14,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical), catalogue mass 180 g. Envelope economics: the 20.6 mm width over a 13.5 mm section yields 1.53 mm of ring width per section millimetre, and the bearing weighs 180 g for 21.6 kN of dynamic capacity — about 8 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 12,000 r/min while thermal balance under catalogue load sets the 14,000 r/min reference; at dm ≈ 38.5 mm the corresponding dn is approximately 462k mm·r/min. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 20.6 mm width gives a bore/width ratio of 1.21; use these ratios when housing space around the 25 mm shaft is the first constraint.",
    "applications": [
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3205 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings of 21.6/14.3 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3205 ATN9 as the double atn9 execution; the other order numbers of the 3205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3205-ATN9?",
        "a": "3205 ATN9 measures 25 mm bore × 52 mm OD × 20.6 mm width (0.984 × 2.047 × 0.811 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 14.3 kN, Pu 0.6 kN, reference speed 14,000 r/min (thermal) and limiting speed 12,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the 52 mm housing; check the wide ring seats square because the 20.6 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3205 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3205-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3205-ATN9",
      "3205 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3305-A",
    "brand": "SKF",
    "manufacturer_designation": "3305 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 32,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3305 A is SKF's 25 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 25×62×25.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 25×62×25.4 mm (0.984×2.441×1 in), 18.5 mm radial section height, C 32 kN, C0 20.4 kN, Pu 0.865 kN.reference speed 12,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 350 g. Sizing arithmetic on the 25 mm bore: 32 kN C divided by the 18.5 mm radial section height gives 1.7 kN per section millimetre; the 350 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 20.4 kN against C 32 kN gives a 0.64 ratio, typical of a double-row bidirectional design; Pu 0.865 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: the reference speed is 12,000 r/min against a 11,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.09.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3305 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Compared with a single-row pair of the same bore, the double-row 3305 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Interference goes on the rotating ring (about k5 at 25 mm bore); the wide 25.4 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Interference goes on the rotating ring (about k5 at 25 mm bore); the wide 25.4 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3305 A as the double a steel execution; the other order numbers of the 3305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3305-A?",
        "a": "3305 A measures 25 mm bore × 62 mm OD × 25.4 mm width (0.984 × 2.441 × 1 in), mass about 350 g. SKF 17000 ratings: C 32 kN, C0 20.4 kN, Pu 0.865 kN, reference speed 12,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3305 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the 62 mm housing; check the wide ring seats square because the 25.4 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3305-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3305-A",
      "3305 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3305-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3305 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 32,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "reference_speed_rpm": 12000,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3305 ATN9 is SKF's 25 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 25×62×25.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 25×62×25.4 mm (0.984×2.441×1 in), 18.5 mm radial section height, C 32 kN, C0 20.4 kN, Pu 0.865 kN.reference speed 12,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical), catalogue mass 350 g. Sizing arithmetic on the 25 mm bore: 32 kN C divided by the 18.5 mm radial section height gives 1.7 kN per section millimetre; the 350 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 350 g inside the 25×62×25.4 mm outline leaves a 18.5 mm radial section, and the 20.4 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 25.4 mm width gives a bore/width ratio of 0.98; use these ratios when housing space around the 25 mm shaft is the first constraint.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3305 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The double-row 3305 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3305 ATN9 as the double atn9 execution; the other order numbers of the 3305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3305-ATN9?",
        "a": "3305 ATN9 measures 25 mm bore × 62 mm OD × 25.4 mm width (0.984 × 2.441 × 1 in), mass about 350 g. SKF 17000 ratings: C 32 kN, C0 20.4 kN, Pu 0.865 kN, reference speed 12,000 r/min (thermal) and limiting speed 11,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Does the 3305 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 25 mm shaft and H7 in the 62 mm housing; check the wide ring seats square because the 25.4 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3305-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3305-ATN9",
      "3305 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3206-A",
    "brand": "SKF",
    "manufacturer_designation": "3206 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 30,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3206 A is SKF's 30 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 30×62×23.8 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 30×62×23.8 mm (1.181×2.441×0.937 in), 16.0 mm radial section height, C 30 kN, C0 20.4 kN, Pu 0.865 kN.reference speed 11,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 290 g. Load balance: C0 20.4 kN against C 30 kN gives a 0.68 ratio, typical of a double-row bidirectional design; Pu 0.865 kN enters the SKF adjusted-life equation rather than the basic rating life. The 0.865 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 30/20.4 kN ratings and 290 g mass this execution carries about 1.00 kN of C per millimetre of bore. Bore-to-OD planning: OD 62 over bore 30 is a 2.07× step for this size, and the 23.8 mm width gives a bore/width ratio of 1.26; use these ratios when housing space around the 30 mm shaft is the first constraint.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The double-row 3206 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The double-row 3206 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings of 30/20.4 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3206 A as the double a steel execution; the other order numbers of the 3206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3206-A?",
        "a": "3206 A measures 30 mm bore × 62 mm OD × 23.8 mm width (1.181 × 2.441 × 0.937 in), mass about 290 g. SKF 17000 ratings: C 30 kN, C0 20.4 kN, Pu 0.865 kN, reference speed 11,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3206 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3206-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3206-A",
      "3206 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3206-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3206 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 30,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "reference_speed_rpm": 11000,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3206 ATN9 is SKF's 30 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 30×62×23.8 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 30×62×23.8 mm (1.181×2.441×0.937 in), 16.0 mm radial section height, C 30 kN, C0 20.4 kN, Pu 0.865 kN.reference speed 11,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical), catalogue mass 290 g. Mass and section check: 290 g inside the 30×62×23.8 mm outline leaves a 16.0 mm radial section, and the 20.4 kN static rating is 0.68× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 0.865 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 30/20.4 kN ratings and 290 g mass this execution carries about 1.00 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 10,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.10.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "A capped 3206-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 30 mm bore); the wide 23.8 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Compared with a single-row pair of the same bore, the double-row 3206 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3206 ATN9 as the double atn9 execution; the other order numbers of the 3206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3206-ATN9?",
        "a": "3206 ATN9 measures 30 mm bore × 62 mm OD × 23.8 mm width (1.181 × 2.441 × 0.937 in), mass about 290 g. SKF 17000 ratings: C 30 kN, C0 20.4 kN, Pu 0.865 kN, reference speed 11,000 r/min (thermal) and limiting speed 10,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Why choose the double-row 3206 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3206-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3206-ATN9",
      "3206 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3306-A",
    "brand": "SKF",
    "manufacturer_designation": "3306 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 42.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3306 A is SKF's 30 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 30×72×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 30×72×30.2 mm (1.181×2.835×1.189 in), 21.0 mm radial section height, C 42.5 kN, C0 30 kN, Pu 1.27 kN.reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 520 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min while thermal balance under catalogue load sets the 10,000 r/min reference; at dm ≈ 51.0 mm the corresponding dn is approximately 459k mm·r/min. Envelope economics: the 30.2 mm width over a 21.0 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 520 g for 42.5 kN of dynamic capacity — about 12 g per rated kN. Bore-to-OD planning: OD 72 over bore 30 is a 2.40× step for this size, and the 30.2 mm width gives a bore/width ratio of 0.99; use these ratios when housing space around the 30 mm shaft is the first constraint.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The double-row 3306 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings of 42.5/30 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The double-row 3306 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Compared with a single-row pair of the same bore, the double-row 3306 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3306 A as the double a steel execution; the other order numbers of the 3306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3306-A?",
        "a": "3306 A measures 30 mm bore × 72 mm OD × 30.2 mm width (1.181 × 2.835 × 1.189 in), mass about 520 g. SKF 17000 ratings: C 42.5 kN, C0 30 kN, Pu 1.27 kN, reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3306 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3306-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3306-A",
      "3306 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3306-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3306 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 42.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3306 ATN9 is SKF's 30 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 30×72×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 30×72×30.2 mm (1.181×2.835×1.189 in), 21.0 mm radial section height, C 42.5 kN, C0 30 kN, Pu 1.27 kN.reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 520 g. At the printed limiting speed of 9,000 r/min the mean pitch diameter dm ≈ 51.0 mm implies a dn value around 459k mm·r/min; the 10,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 30.2 mm width over a 21.0 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 520 g for 42.5 kN of dynamic capacity — about 12 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 10,000 r/min against a 9,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.11.",
    "applications": [
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "The double-row 3306 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Interference goes on the rotating ring (about k5 at 30 mm bore); the wide 30.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings of 42.5/30 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3306 ATN9 as the double atn9 execution; the other order numbers of the 3306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3306-ATN9?",
        "a": "3306 ATN9 measures 30 mm bore × 72 mm OD × 30.2 mm width (1.181 × 2.835 × 1.189 in), mass about 520 g. SKF 17000 ratings: C 42.5 kN, C0 30 kN, Pu 1.27 kN, reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3306 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3306-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3306-ATN9",
      "3306 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3207-A",
    "brand": "SKF",
    "manufacturer_designation": "3207 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 40,
    "static_load_kN": 28,
    "fatigue_load_limit_kN": 1.18,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 440,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3207 A is SKF's 35 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 35×72×27 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 35×72×27 mm (1.378×2.835×1.063 in), 18.5 mm radial section height, C 40 kN, C0 28 kN, Pu 1.18 kN.reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 440 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min while thermal balance under catalogue load sets the 10,000 r/min reference; at dm ≈ 53.5 mm the corresponding dn is approximately 482k mm·r/min. Envelope economics: the 27 mm width over a 18.5 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 440 g for 40 kN of dynamic capacity — about 11 g per rated kN. Bore-to-OD planning: OD 72 over bore 35 is a 2.06× step for this size, and the 27 mm width gives a bore/width ratio of 1.30; use these ratios when housing space around the 35 mm shaft is the first constraint.",
    "applications": [
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The double-row 3207 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The double-row 3207 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The double-row 3207 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings of 40/28 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3207 A as the double a steel execution; the other order numbers of the 3207 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3207-A?",
        "a": "3207 A measures 35 mm bore × 72 mm OD × 27 mm width (1.378 × 2.835 × 1.063 in), mass about 440 g. SKF 17000 ratings: C 40 kN, C0 28 kN, Pu 1.18 kN, reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3207 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3207-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3207-A",
      "3207 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3207-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3207 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 40,
    "static_load_kN": 28,
    "fatigue_load_limit_kN": 1.18,
    "reference_speed_rpm": 10000,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 440,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3207 ATN9 is SKF's 35 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 35×72×27 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 35×72×27 mm (1.378×2.835×1.063 in), 18.5 mm radial section height, C 40 kN, C0 28 kN, Pu 1.18 kN.reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical), catalogue mass 440 g. At the printed limiting speed of 9,000 r/min the mean pitch diameter dm ≈ 53.5 mm implies a dn value around 482k mm·r/min; the 10,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 27 mm width over a 18.5 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 440 g for 40 kN of dynamic capacity — about 11 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 10,000 r/min against a 9,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.11.",
    "applications": [
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "A capped 3207-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings of 40/28 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings of 40/28 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3207 ATN9 as the double atn9 execution; the other order numbers of the 3207 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3207-ATN9?",
        "a": "3207 ATN9 measures 35 mm bore × 72 mm OD × 27 mm width (1.378 × 2.835 × 1.063 in), mass about 440 g. SKF 17000 ratings: C 40 kN, C0 28 kN, Pu 1.18 kN, reference speed 10,000 r/min (thermal) and limiting speed 9,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3207 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3207-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3207-ATN9",
      "3207 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3307-A",
    "brand": "SKF",
    "manufacturer_designation": "3307 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 52,
    "static_load_kN": 35.5,
    "fatigue_load_limit_kN": 1.5,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3307 A is SKF's 35 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 35×80×34.9 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 35×80×34.9 mm (1.378×3.15×1.374 in), 22.5 mm radial section height, C 52 kN, C0 35.5 kN, Pu 1.5 kN.reference speed 9,500 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 740 g. Load balance: C0 35.5 kN against C 52 kN gives a 0.68 ratio, typical of a double-row bidirectional design; Pu 1.5 kN enters the SKF adjusted-life equation rather than the basic rating life. The 1.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 52/35.5 kN ratings and 740 g mass this execution carries about 1.49 kN of C per millimetre of bore. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 34.9 mm width gives a bore/width ratio of 1.00; use these ratios when housing space around the 35 mm shaft is the first constraint.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Catalogue ratings of 52/35.5 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Interference goes on the rotating ring (about k5 at 35 mm bore); the wide 34.9 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The double-row 3307 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The double-row 3307 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3307 A as the double a steel execution; the other order numbers of the 3307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3307-A?",
        "a": "3307 A measures 35 mm bore × 80 mm OD × 34.9 mm width (1.378 × 3.15 × 1.374 in), mass about 740 g. SKF 17000 ratings: C 52 kN, C0 35.5 kN, Pu 1.5 kN, reference speed 9,500 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3307 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3307-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-DJ1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52/35.5 kN vs 52.7/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3307-A",
      "3307 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3307-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3307 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 52,
    "static_load_kN": 35.5,
    "fatigue_load_limit_kN": 1.5,
    "reference_speed_rpm": 9500,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3307 ATN9 is SKF's 35 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 35×80×34.9 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 35×80×34.9 mm (1.378×3.15×1.374 in), 22.5 mm radial section height, C 52 kN, C0 35.5 kN, Pu 1.5 kN.reference speed 9,500 r/min (thermal) and limiting speed 8,500 r/min (mechanical), catalogue mass 740 g. Mass and section check: 740 g inside the 35×80×34.9 mm outline leaves a 22.5 mm radial section, and the 35.5 kN static rating is 0.68× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 1.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 52/35.5 kN ratings and 740 g mass this execution carries about 1.49 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 9,500 r/min against a 8,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.12.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The double-row 3307 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "A capped 3307-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3307 ATN9 as the double atn9 execution; the other order numbers of the 3307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3307-ATN9?",
        "a": "3307 ATN9 measures 35 mm bore × 80 mm OD × 34.9 mm width (1.378 × 3.15 × 1.374 in), mass about 740 g. SKF 17000 ratings: C 52 kN, C0 35.5 kN, Pu 1.5 kN, reference speed 9,500 r/min (thermal) and limiting speed 8,500 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Why choose the double-row 3307 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3307-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-DJ1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52/35.5 kN vs 52.7/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3307-ATN9",
      "3307 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3307-DJ1",
    "brand": "SKF",
    "manufacturer_designation": "3307 DJ1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 52.7,
    "static_load_kN": 41.5,
    "fatigue_load_limit_kN": 1.76,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 790,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3307 DJ1 is SKF's 35 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 35×80×34.9 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DJ1 combines the split inner ring with the J1 stamped steel ball-centred cage. Envelope 35×80×34.9 mm (1.378×3.15×1.374 in), 22.5 mm radial section height, C 52.7 kN, C0 41.5 kN, Pu 1.76 kN.reference speed 9,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 790 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 8,000 r/min while thermal balance under catalogue load sets the 9,000 r/min reference; at dm ≈ 57.5 mm the corresponding dn is approximately 460k mm·r/min. At the printed limiting speed of 8,000 r/min the mean pitch diameter dm ≈ 57.5 mm implies a dn value around 460k mm·r/min; the 9,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 34.9 mm width gives a bore/width ratio of 1.00; use these ratios when housing space around the 35 mm shaft is the first constraint.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped J1 cage distortion if the split inner ring is assembled with the halves misaligned",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "A capped 3307-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The double-row 3307 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings of 52.7/41.5 kN apply to the DJ1 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3307 DJ1 as the double d j1 execution; the other order numbers of the 3307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3307-DJ1?",
        "a": "3307 DJ1 measures 35 mm bore × 80 mm OD × 34.9 mm width (1.378 × 3.15 × 1.374 in), mass about 790 g. SKF 17000 ratings: C 52.7 kN, C0 41.5 kN, Pu 1.76 kN, reference speed 9,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the DJ1 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DJ1 combines the split inner ring with the J1 stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 35 mm shaft and H7 in the 80 mm housing; check the wide ring seats square because the 34.9 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3307 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3307-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52.7/41.5 kN vs 52/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52.7/41.5 kN vs 52/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52.7/41.5 kN vs 52/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52.7/41.5 kN vs 52/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3307-DJ1",
      "3307 DJ1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3208-A",
    "brand": "SKF",
    "manufacturer_designation": "3208 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 48,
    "static_load_kN": 36.5,
    "fatigue_load_limit_kN": 1.56,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3208 A is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 40×80×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 40×80×30.2 mm (1.575×3.15×1.189 in), 20.0 mm radial section height, C 48 kN, C0 36.5 kN, Pu 1.56 kN.reference speed 9,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 570 g. The 1.56 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 48/36.5 kN ratings and 570 g mass this execution carries about 1.20 kN of C per millimetre of bore. Mass and section check: 570 g inside the 40×80×30.2 mm outline leaves a 20.0 mm radial section, and the 36.5 kN static rating is 0.76× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 9,000 r/min against a 8,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.13.",
    "applications": [
      "centrifugal pump shafts",
      "elevator and hoist machinery",
      "printing and converting machinery"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Interference goes on the rotating ring (about k5 at 40 mm bore); the wide 30.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings of 48/36.5 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Interference goes on the rotating ring (about k5 at 40 mm bore); the wide 30.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3208 A as the double a steel execution; the other order numbers of the 3208 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3208-A?",
        "a": "3208 A measures 40 mm bore × 80 mm OD × 30.2 mm width (1.575 × 3.15 × 1.189 in), mass about 570 g. SKF 17000 ratings: C 48 kN, C0 36.5 kN, Pu 1.56 kN, reference speed 9,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3208 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the 80 mm housing; check the wide ring seats square because the 30.2 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3208-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3208-A",
      "3208 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3208-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3208 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 48,
    "static_load_kN": 36.5,
    "fatigue_load_limit_kN": 1.56,
    "reference_speed_rpm": 9000,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3208 ATN9 is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 40×80×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 40×80×30.2 mm (1.575×3.15×1.189 in), 20.0 mm radial section height, C 48 kN, C0 36.5 kN, Pu 1.56 kN.reference speed 9,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical), catalogue mass 570 g. The 1.56 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 48/36.5 kN ratings and 570 g mass this execution carries about 1.20 kN of C per millimetre of bore. Load balance: C0 36.5 kN against C 48 kN gives a 0.76 ratio, typical of a double-row bidirectional design; Pu 1.56 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 80 over bore 40 is a 2.00× step for this size, and the 30.2 mm width gives a bore/width ratio of 1.32; use these ratios when housing space around the 40 mm shaft is the first constraint.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "A capped 3208-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3208-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings of 48/36.5 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3208 ATN9 as the double atn9 execution; the other order numbers of the 3208 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3208-ATN9?",
        "a": "3208 ATN9 measures 40 mm bore × 80 mm OD × 30.2 mm width (1.575 × 3.15 × 1.189 in), mass about 570 g. SKF 17000 ratings: C 48 kN, C0 36.5 kN, Pu 1.56 kN, reference speed 9,000 r/min (thermal) and limiting speed 8,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Does the 3208 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the 80 mm housing; check the wide ring seats square because the 30.2 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3208-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3208-ATN9",
      "3208 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-DNRCBM",
    "brand": "SKF",
    "manufacturer_designation": "3308 DNRCBM",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 49.4,
    "static_load_kN": 41.5,
    "fatigue_load_limit_kN": 1.76,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 DNRCBM is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 40×90×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 49.4 kN, C0 41.5 kN, Pu 1.76 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 1200 g. Sizing arithmetic on the 40 mm bore: 49.4 kN C divided by the 25.0 mm radial section height gives 2.0 kN per section millimetre; the 1200 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 36.5 mm width over a 25.0 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 1200 g for 49.4 kN of dynamic capacity — about 24 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.14.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "snap-ring groove distress or ring rotation if the NR snap ring is not seated fully in its groove",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The double-row 3308 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The double-row 3308 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "A capped 3308-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings of 49.4/41.5 kN apply to the DNRCBM execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 DNRCBM as the double d nr cb m execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-DNRCBM?",
        "a": "3308 DNRCBM measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 1200 g. SKF 17000 ratings: C 49.4 kN, C0 41.5 kN, Pu 1.76 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the DNRCBM suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Why choose the double-row 3308 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in DNRCBM?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (49.4/41.5 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (49.4/41.5 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (49.4/41.5 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (49.4/41.5 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (49.4/41.5 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (49.4/41.5 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-DNRCBM",
      "3308 DNRCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-A",
    "brand": "SKF",
    "manufacturer_designation": "3308 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 64,
    "static_load_kN": 44,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 930,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 A is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 40×90×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 64 kN, C0 44 kN, Pu 1.86 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 930 g. Selection figures for 3308 A: the static-to-dynamic ratio C0/C is 0.69, Pu 1.86 kN is about 3 % of C, and catalogue mass works out to roughly 23 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 8,000 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 488k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 7,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.07.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "A capped 3308-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Compared with a single-row pair of the same bore, the double-row 3308 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3308-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 A as the double a steel execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-A?",
        "a": "3308 A measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 930 g. SKF 17000 ratings: C 64 kN, C0 44 kN, Pu 1.86 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the 90 mm housing; check the wide ring seats square because the 36.5 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3308 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 49.4/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-A",
      "3308 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3308 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 64,
    "static_load_kN": 44,
    "fatigue_load_limit_kN": 1.86,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 930,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 ATN9 is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 40×90×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 64 kN, C0 44 kN, Pu 1.86 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 930 g. Selection figures for 3308 ATN9: the static-to-dynamic ratio C0/C is 0.69, Pu 1.86 kN is about 3 % of C, and catalogue mass works out to roughly 23 g per millimetre of bore. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 488k mm·r/min; the 8,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 36.5 mm width gives a bore/width ratio of 1.10; use these ratios when housing space around the 40 mm shaft is the first constraint.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 40 mm bore); the wide 36.5 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Interference goes on the rotating ring (about k5 at 40 mm bore); the wide 36.5 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "A capped 3308-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 ATN9 as the double atn9 execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-ATN9?",
        "a": "3308 ATN9 measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 930 g. SKF 17000 ratings: C 64 kN, C0 44 kN, Pu 1.86 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the 90 mm housing; check the wide ring seats square because the 36.5 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3308 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 49.4/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-ATN9",
      "3308 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-DMA",
    "brand": "SKF",
    "manufacturer_designation": "3308 DMA",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 68.9,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 DMA is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 40×90×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 68.9 kN, C0 57 kN, Pu 2.45 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 1050 g. Mass and section check: 1050 g inside the 40×90×36.5 mm outline leaves a 25.0 mm radial section, and the 57 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 7,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 455k mm·r/min; the 8,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.14. Split-ring execution note: DMA combines the two-piece inner ring (used to simplify mounting of the wide 33-series section) with a machined brass cage guided on the outer ring (MA rather than ball-centred M); outer-ring guidance steadies the cage in the heavy section at the cost of a different lubrication requirement at the guide land.",
    "applications": [
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "uneven loading of the split inner-ring halves if the MA cage guide land runs dry",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The double-row 3308 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Compared with a single-row pair of the same bore, the double-row 3308 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3308-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3308-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 DMA as the double d ma execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-DMA?",
        "a": "3308 DMA measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 1050 g. SKF 17000 ratings: C 68.9 kN, C0 57 kN, Pu 2.45 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the DMA suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage."
      },
      {
        "q": "Does the 3308 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the 90 mm housing; check the wide ring seats square because the 36.5 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 49.4/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DTN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 DTN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-DMA",
      "3308 DMA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-DTN9",
    "brand": "SKF",
    "manufacturer_designation": "3308 DTN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 68.9,
    "static_load_kN": 57,
    "fatigue_load_limit_kN": 2.45,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 DTN9 is SKF's 40 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 40×90×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. DTN9 combines the split inner ring with the glass-fibre PA66 ball-centred TN9 cage. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 68.9 kN, C0 57 kN, Pu 2.45 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 1050 g. Load balance: C0 57 kN against C 68.9 kN gives a 0.83 ratio, typical of a double-row bidirectional design; Pu 2.45 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 1050 g inside the 40×90×36.5 mm outline leaves a 25.0 mm radial section, and the 57 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.14.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "TN9 cage damage when the split-ring bearing is heated above the PA66 ceiling during mounting",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3308 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Compared with a single-row pair of the same bore, the double-row 3308 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 DTN9 as the double d tn9 execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-DTN9?",
        "a": "3308 DTN9 measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 1050 g. SKF 17000 ratings: C 68.9 kN, C0 57 kN, Pu 2.45 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the DTN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. DTN9 combines the split inner ring with the glass-fibre PA66 ball-centred TN9 cage."
      },
      {
        "q": "Does the 3308 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 40 mm shaft and H7 in the 90 mm housing; check the wide ring seats square because the 36.5 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 49.4/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DMA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 DMA is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (68.9/57 kN vs 64/44 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-DTN9",
      "3308 DTN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3209-A",
    "brand": "SKF",
    "manufacturer_designation": "3209 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 51,
    "static_load_kN": 39,
    "fatigue_load_limit_kN": 1.63,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3209 A is SKF's 45 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 45×85×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 45×85×30.2 mm (1.772×3.346×1.189 in), 20.0 mm radial section height, C 51 kN, C0 39 kN, Pu 1.63 kN.reference speed 8,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 630 g. Selection figures for 3209 A: the static-to-dynamic ratio C0/C is 0.76, Pu 1.63 kN is about 3 % of C, and catalogue mass works out to roughly 14 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min while thermal balance under catalogue load sets the 8,500 r/min reference; at dm ≈ 65.0 mm the corresponding dn is approximately 488k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 8,500 r/min against a 7,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.13.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The double-row 3209 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "A capped 3209-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3209 A as the double a steel execution; the other order numbers of the 3209 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3209-A?",
        "a": "3209 A measures 45 mm bore × 85 mm OD × 30.2 mm width (1.772 × 3.346 × 1.189 in), mass about 630 g. SKF 17000 ratings: C 51 kN, C0 39 kN, Pu 1.63 kN, reference speed 8,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the 85 mm housing; check the wide ring seats square because the 30.2 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3209 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3209-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3209-A",
      "3209 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3209-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3209 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 51,
    "static_load_kN": 39,
    "fatigue_load_limit_kN": 1.63,
    "reference_speed_rpm": 8500,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3209 ATN9 is SKF's 45 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 45×85×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 45×85×30.2 mm (1.772×3.346×1.189 in), 20.0 mm radial section height, C 51 kN, C0 39 kN, Pu 1.63 kN.reference speed 8,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical), catalogue mass 630 g. Selection figures for 3209 ATN9: the static-to-dynamic ratio C0/C is 0.76, Pu 1.63 kN is about 3 % of C, and catalogue mass works out to roughly 14 g per millimetre of bore. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 488k mm·r/min; the 8,500 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 85 over bore 45 is a 1.89× step for this size, and the 30.2 mm width gives a bore/width ratio of 1.49; use these ratios when housing space around the 45 mm shaft is the first constraint.",
    "applications": [
      "centrifugal pump shafts",
      "elevator and hoist machinery",
      "printing and converting machinery"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The double-row 3209 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings of 51/39 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The double-row 3209 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3209 ATN9 as the double atn9 execution; the other order numbers of the 3209 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3209-ATN9?",
        "a": "3209 ATN9 measures 45 mm bore × 85 mm OD × 30.2 mm width (1.772 × 3.346 × 1.189 in), mass about 630 g. SKF 17000 ratings: C 51 kN, C0 39 kN, Pu 1.63 kN, reference speed 8,500 r/min (thermal) and limiting speed 7,500 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the 85 mm housing; check the wide ring seats square because the 30.2 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3209 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3209-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3209-ATN9",
      "3209 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3309-DNRCBM",
    "brand": "SKF",
    "manufacturer_designation": "3309 DNRCBM",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 61.8,
    "static_load_kN": 52,
    "fatigue_load_limit_kN": 2.2,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3309 DNRCBM is SKF's 45 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 45×100×39.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 45×100×39.7 mm (1.772×3.937×1.563 in), 27.5 mm radial section height, C 61.8 kN, C0 52 kN, Pu 2.2 kN.reference speed 7,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1500 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 6,300 r/min while thermal balance under catalogue load sets the 7,500 r/min reference; at dm ≈ 72.5 mm the corresponding dn is approximately 457k mm·r/min. At the printed limiting speed of 6,300 r/min the mean pitch diameter dm ≈ 72.5 mm implies a dn value around 457k mm·r/min; the 7,500 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 7,500 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.19.",
    "applications": [
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "snap-ring groove distress or ring rotation if the NR snap ring is not seated fully in its groove",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The double-row 3309 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Interference goes on the rotating ring (about k5 at 45 mm bore); the wide 39.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Compared with a single-row pair of the same bore, the double-row 3309 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Controlled axial clearance is the heart of the design: CB denotes controlled Normal axial clearance between the two rows; check residual clearance after mounting and at operating temperature.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3309 DNRCBM as the double d nr cb m execution; the other order numbers of the 3309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3309-DNRCBM?",
        "a": "3309 DNRCBM measures 45 mm bore × 100 mm OD × 39.7 mm width (1.772 × 3.937 × 1.563 in), mass about 1500 g. SKF 17000 ratings: C 61.8 kN, C0 52 kN, Pu 2.2 kN, reference speed 7,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the DNRCBM suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the 100 mm housing; check the wide ring seats square because the 39.7 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3309 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3309-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (61.8/52 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (61.8/52 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (61.8/52 kN vs 79.3/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (61.8/52 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (61.8/52 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3309-DNRCBM",
      "3309 DNRCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3309-A",
    "brand": "SKF",
    "manufacturer_designation": "3309 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 75,
    "static_load_kN": 53,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3309 A is SKF's 45 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 45×100×39.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 45×100×39.7 mm (1.772×3.937×1.563 in), 27.5 mm radial section height, C 75 kN, C0 53 kN, Pu 2.24 kN.reference speed 7,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1250 g. The 2.24 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 75/53 kN ratings and 1250 g mass this execution carries about 1.67 kN of C per millimetre of bore. Mass and section check: 1250 g inside the 45×100×39.7 mm outline leaves a 27.5 mm radial section, and the 53 kN static rating is 0.71× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 7,500 r/min against a 6,700 r/min limiting speed, i.e. a reference-to-limit ratio of 1.12.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Catalogue ratings of 75/53 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Interference goes on the rotating ring (about k5 at 45 mm bore); the wide 39.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Interference goes on the rotating ring (about k5 at 45 mm bore); the wide 39.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The double-row 3309 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3309 A as the double a steel execution; the other order numbers of the 3309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3309-A?",
        "a": "3309 A measures 45 mm bore × 100 mm OD × 39.7 mm width (1.772 × 3.937 × 1.563 in), mass about 1250 g. SKF 17000 ratings: C 75 kN, C0 53 kN, Pu 2.24 kN, reference speed 7,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3309 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the 100 mm housing; check the wide ring seats square because the 39.7 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3309-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 61.8/52 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 79.3/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3309-A",
      "3309 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3309-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3309 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 75,
    "static_load_kN": 53,
    "fatigue_load_limit_kN": 2.24,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3309 ATN9 is SKF's 45 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 45×100×39.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 45×100×39.7 mm (1.772×3.937×1.563 in), 27.5 mm radial section height, C 75 kN, C0 53 kN, Pu 2.24 kN.reference speed 7,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical), catalogue mass 1250 g. The 2.24 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 75/53 kN ratings and 1250 g mass this execution carries about 1.67 kN of C per millimetre of bore. Load balance: C0 53 kN against C 75 kN gives a 0.71 ratio, typical of a double-row bidirectional design; Pu 2.24 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 39.7 mm width gives a bore/width ratio of 1.13; use these ratios when housing space around the 45 mm shaft is the first constraint.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The double-row 3309 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "A capped 3309-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 45 mm bore); the wide 39.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3309 ATN9 as the double atn9 execution; the other order numbers of the 3309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3309-ATN9?",
        "a": "3309 ATN9 measures 45 mm bore × 100 mm OD × 39.7 mm width (1.772 × 3.937 × 1.563 in), mass about 1250 g. SKF 17000 ratings: C 75 kN, C0 53 kN, Pu 2.24 kN, reference speed 7,500 r/min (thermal) and limiting speed 6,700 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Does the 3309 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 45 mm shaft and H7 in the 100 mm housing; check the wide ring seats square because the 39.7 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3309-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 61.8/52 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 79.3/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3309-ATN9",
      "3309 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3309-DMA",
    "brand": "SKF",
    "manufacturer_designation": "3309 DMA",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 79.3,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 3,
    "reference_speed_rpm": 7500,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 1650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3309 DMA is SKF's 45 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 45×100×39.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage. Envelope 45×100×39.7 mm (1.772×3.937×1.563 in), 27.5 mm radial section height, C 79.3 kN, C0 69.5 kN, Pu 3 kN.reference speed 7,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical), catalogue mass 1650 g. Selection figures for 3309 DMA: the static-to-dynamic ratio C0/C is 0.88, Pu 3 kN is about 4 % of C, and catalogue mass works out to roughly 37 g per millimetre of bore. Envelope economics: the 39.7 mm width over a 27.5 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 1650 g for 79.3 kN of dynamic capacity — about 21 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 7,500 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.19. Split-ring execution note: DMA combines the two-piece inner ring (used to simplify mounting of the wide 33-series section) with a machined brass cage guided on the outer ring (MA rather than ball-centred M); outer-ring guidance steadies the cage in the heavy section at the cost of a different lubrication requirement at the guide land.",
    "applications": [
      "centrifugal pump shafts",
      "elevator and hoist machinery",
      "printing and converting machinery"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "uneven loading of the split inner-ring halves if the MA cage guide land runs dry",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Catalogue ratings of 79.3/69.5 kN apply to the DMA execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The double-row 3309 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Interference goes on the rotating ring (about k5 at 45 mm bore); the wide 39.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Compared with a single-row pair of the same bore, the double-row 3309 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3309 DMA as the double d ma execution; the other order numbers of the 3309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3309-DMA?",
        "a": "3309 DMA measures 45 mm bore × 100 mm OD × 39.7 mm width (1.772 × 3.937 × 1.563 in), mass about 1650 g. SKF 17000 ratings: C 79.3 kN, C0 69.5 kN, Pu 3 kN, reference speed 7,500 r/min (thermal) and limiting speed 6,300 r/min (mechanical)."
      },
      {
        "q": "What does the DMA suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage."
      },
      {
        "q": "What does the D mean in DMA?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3309 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3309-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (79.3/69.5 kN vs 61.8/52 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (79.3/69.5 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (79.3/69.5 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (79.3/69.5 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (79.3/69.5 kN vs 75/53 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3309-DMA",
      "3309 DMA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3210-A",
    "brand": "SKF",
    "manufacturer_designation": "3210 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 51,
    "static_load_kN": 42.5,
    "fatigue_load_limit_kN": 1.8,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3210 A is SKF's 50 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 50×90×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 50×90×30.2 mm (1.969×3.543×1.189 in), 20.0 mm radial section height, C 51 kN, C0 42.5 kN, Pu 1.8 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 650 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,000 r/min while thermal balance under catalogue load sets the 8,000 r/min reference; at dm ≈ 70.0 mm the corresponding dn is approximately 490k mm·r/min. Envelope economics: the 30.2 mm width over a 20.0 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 650 g for 51 kN of dynamic capacity — about 13 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 8,000 r/min against a 7,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.14.",
    "applications": [
      "centrifugal pump shafts",
      "elevator and hoist machinery",
      "printing and converting machinery"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 50 mm bore); the wide 30.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "A capped 3210-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 50 mm bore); the wide 30.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Compared with a single-row pair of the same bore, the double-row 3210 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3210 A as the double a steel execution; the other order numbers of the 3210 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3210-A?",
        "a": "3210 A measures 50 mm bore × 90 mm OD × 30.2 mm width (1.969 × 3.543 × 1.189 in), mass about 650 g. SKF 17000 ratings: C 51 kN, C0 42.5 kN, Pu 1.8 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3210 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3210-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3210-A",
      "3210 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3210-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3210 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 51,
    "static_load_kN": 42.5,
    "fatigue_load_limit_kN": 1.8,
    "reference_speed_rpm": 8000,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3210 ATN9 is SKF's 50 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 50×90×30.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 50×90×30.2 mm (1.969×3.543×1.189 in), 20.0 mm radial section height, C 51 kN, C0 42.5 kN, Pu 1.8 kN.reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical), catalogue mass 650 g. At the printed limiting speed of 7,000 r/min the mean pitch diameter dm ≈ 70.0 mm implies a dn value around 490k mm·r/min; the 8,000 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 30.2 mm width over a 20.0 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 650 g for 51 kN of dynamic capacity — about 13 g per rated kN. Bore-to-OD planning: OD 90 over bore 50 is a 1.80× step for this size, and the 30.2 mm width gives a bore/width ratio of 1.66; use these ratios when housing space around the 50 mm shaft is the first constraint.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 50 mm bore); the wide 30.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Compared with a single-row pair of the same bore, the double-row 3210 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings of 51/42.5 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3210 ATN9 as the double atn9 execution; the other order numbers of the 3210 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3210-ATN9?",
        "a": "3210 ATN9 measures 50 mm bore × 90 mm OD × 30.2 mm width (1.969 × 3.543 × 1.189 in), mass about 650 g. SKF 17000 ratings: C 51 kN, C0 42.5 kN, Pu 1.8 kN, reference speed 8,000 r/min (thermal) and limiting speed 7,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3210 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3210-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3210-ATN9",
      "3210 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3310-DNRCBM",
    "brand": "SKF",
    "manufacturer_designation": "3310 DNRCBM",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 81.9,
    "static_load_kN": 69.5,
    "fatigue_load_limit_kN": 3,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3310 DNRCBM is SKF's 50 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 50×110×44.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 50×110×44.4 mm (1.969×4.331×1.748 in), 30.0 mm radial section height, C 81.9 kN, C0 69.5 kN, Pu 3 kN.reference speed 6,700 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 1950 g. Selection figures for 3310 DNRCBM: the static-to-dynamic ratio C0/C is 0.85, Pu 3 kN is about 4 % of C, and catalogue mass works out to roughly 39 g per millimetre of bore. Envelope economics: the 44.4 mm width over a 30.0 mm section yields 1.48 mm of ring width per section millimetre, and the bearing weighs 1950 g for 81.9 kN of dynamic capacity — about 24 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.20.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove distress or ring rotation if the NR snap ring is not seated fully in its groove",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Controlled axial clearance is the heart of the design: CB denotes controlled Normal axial clearance between the two rows; check residual clearance after mounting and at operating temperature.",
      "Interference goes on the rotating ring (about k5 at 50 mm bore); the wide 44.4 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3310 DNRCBM as the double d nr cb m execution; the other order numbers of the 3310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3310-DNRCBM?",
        "a": "3310 DNRCBM measures 50 mm bore × 110 mm OD × 44.4 mm width (1.969 × 4.331 × 1.748 in), mass about 1950 g. SKF 17000 ratings: C 81.9 kN, C0 69.5 kN, Pu 3 kN, reference speed 6,700 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the DNRCBM suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "What does the D mean in DNRCBM?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3310 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3310-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (81.9/69.5 kN vs 93.6/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3310-DNRCBM",
      "3310 DNRCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3310-A",
    "brand": "SKF",
    "manufacturer_designation": "3310 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 90,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3310 A is SKF's 50 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 50×110×44.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 50×110×44.4 mm (1.969×4.331×1.748 in), 30.0 mm radial section height, C 90 kN, C0 64 kN, Pu 2.75 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 1700 g. Mass and section check: 1700 g inside the 50×110×44.4 mm outline leaves a 30.0 mm radial section, and the 64 kN static rating is 0.71× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 50 mm bore: 90 kN C divided by the 30.0 mm radial section height gives 3.0 kN per section millimetre; the 1700 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 6,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.12.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Catalogue ratings of 90/64 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The double-row 3310 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3310 A as the double a steel execution; the other order numbers of the 3310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3310-A?",
        "a": "3310 A measures 50 mm bore × 110 mm OD × 44.4 mm width (1.969 × 4.331 × 1.748 in), mass about 1700 g. SKF 17000 ratings: C 90 kN, C0 64 kN, Pu 2.75 kN, reference speed 6,700 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3310 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3310-DNRCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 DNRCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (90/64 kN vs 93.6/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3310-A",
      "3310 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3310-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3310 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 90,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.75,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3310 ATN9 is SKF's 50 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 50×110×44.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 50×110×44.4 mm (1.969×4.331×1.748 in), 30.0 mm radial section height, C 90 kN, C0 64 kN, Pu 2.75 kN.reference speed 6,700 r/min (thermal) and limiting speed 6,000 r/min (mechanical), catalogue mass 1700 g. Load balance: C0 64 kN against C 90 kN gives a 0.71 ratio, typical of a double-row bidirectional design; Pu 2.75 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 50 mm bore: 90 kN C divided by the 30.0 mm radial section height gives 3.0 kN per section millimetre; the 1700 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 44.4 mm width gives a bore/width ratio of 1.13; use these ratios when housing space around the 50 mm shaft is the first constraint.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The double-row 3310 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Compared with a single-row pair of the same bore, the double-row 3310 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Compared with a single-row pair of the same bore, the double-row 3310 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3310-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3310 ATN9 as the double atn9 execution; the other order numbers of the 3310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3310-ATN9?",
        "a": "3310 ATN9 measures 50 mm bore × 110 mm OD × 44.4 mm width (1.969 × 4.331 × 1.748 in), mass about 1700 g. SKF 17000 ratings: C 90 kN, C0 64 kN, Pu 2.75 kN, reference speed 6,700 r/min (thermal) and limiting speed 6,000 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Why choose the double-row 3310 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3310-DNRCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 DNRCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (90/64 kN vs 93.6/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3310-ATN9",
      "3310 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3310-DMA",
    "brand": "SKF",
    "manufacturer_designation": "3310 DMA",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 93.6,
    "static_load_kN": 85,
    "fatigue_load_limit_kN": 3.6,
    "reference_speed_rpm": 6700,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 2200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3310 DMA is SKF's 50 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 50×110×44.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage. Envelope 50×110×44.4 mm (1.969×4.331×1.748 in), 30.0 mm radial section height, C 93.6 kN, C0 85 kN, Pu 3.6 kN.reference speed 6,700 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 2200 g. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 80.0 mm implies a dn value around 448k mm·r/min; the 6,700 r/min reference speed is the thermal-planning figure under catalogue load. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 6,700 r/min reference; at dm ≈ 80.0 mm the corresponding dn is approximately 448k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 6,700 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.20. Split-ring execution note: DMA combines the two-piece inner ring (used to simplify mounting of the wide 33-series section) with a machined brass cage guided on the outer ring (MA rather than ball-centred M); outer-ring guidance steadies the cage in the heavy section at the cost of a different lubrication requirement at the guide land.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "uneven loading of the split inner-ring halves if the MA cage guide land runs dry",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 50 mm bore); the wide 44.4 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "A capped 3310-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3310-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3310 DMA as the double d ma execution; the other order numbers of the 3310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3310-DMA?",
        "a": "3310 DMA measures 50 mm bore × 110 mm OD × 44.4 mm width (1.969 × 4.331 × 1.748 in), mass about 2200 g. SKF 17000 ratings: C 93.6 kN, C0 85 kN, Pu 3.6 kN, reference speed 6,700 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the DMA suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 50 mm shaft and H7 in the 110 mm housing; check the wide ring seats square because the 44.4 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3310 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3310-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (93.6/85 kN vs 81.9/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (93.6/85 kN vs 90/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (93.6/85 kN vs 90/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (93.6/85 kN vs 90/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (93.6/85 kN vs 90/64 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3310-DMA",
      "3310 DMA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3211-A",
    "brand": "SKF",
    "manufacturer_designation": "3211 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 33.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 60,
    "static_load_kN": 47.5,
    "fatigue_load_limit_kN": 2,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3211 A is SKF's 55 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 55×100×33.3 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 55×100×33.3 mm (2.165×3.937×1.311 in), 22.5 mm radial section height, C 60 kN, C0 47.5 kN, Pu 2 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size, catalogue mass 910 g. Load balance: C0 47.5 kN against C 60 kN gives a 0.79 ratio, typical of a double-row bidirectional design; Pu 2 kN enters the SKF adjusted-life equation rather than the basic rating life. The 2 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 60/47.5 kN ratings and 910 g mass this execution carries about 1.09 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 6,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00.",
    "applications": [
      "elevator and hoist machinery",
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Compared with a single-row pair of the same bore, the double-row 3211 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings of 60/47.5 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Compared with a single-row pair of the same bore, the double-row 3211 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3211 A as the double a steel execution; the other order numbers of the 3211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3211-A?",
        "a": "3211 A measures 55 mm bore × 100 mm OD × 33.3 mm width (2.165 × 3.937 × 1.311 in), mass about 910 g. SKF 17000 ratings: C 60 kN, C0 47.5 kN, Pu 2 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3211 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3211-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3211-A",
      "3211 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3211-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3211 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 33.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 60,
    "static_load_kN": 47.5,
    "fatigue_load_limit_kN": 2,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3211 ATN9 is SKF's 55 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 55×100×33.3 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 55×100×33.3 mm (2.165×3.937×1.311 in), 22.5 mm radial section height, C 60 kN, C0 47.5 kN, Pu 2 kN.reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size, catalogue mass 910 g. Mass and section check: 910 g inside the 55×100×33.3 mm outline leaves a 22.5 mm radial section, and the 47.5 kN static rating is 0.79× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. The 2 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 60/47.5 kN ratings and 910 g mass this execution carries about 1.09 kN of C per millimetre of bore. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 33.3 mm width gives a bore/width ratio of 1.65; use these ratios when housing space around the 55 mm shaft is the first constraint.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The double-row 3211 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Compared with a single-row pair of the same bore, the double-row 3211 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Compared with a single-row pair of the same bore, the double-row 3211 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3211-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3211 ATN9 as the double atn9 execution; the other order numbers of the 3211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3211-ATN9?",
        "a": "3211 ATN9 measures 55 mm bore × 100 mm OD × 33.3 mm width (2.165 × 3.937 × 1.311 in), mass about 910 g. SKF 17000 ratings: C 60 kN, C0 47.5 kN, Pu 2 kN, reference speed 6,300 r/min (thermal) and limiting speed 6,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Why choose the double-row 3211 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3211-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3211-ATN9",
      "3211 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3311-DNRCBM",
    "brand": "SKF",
    "manufacturer_designation": "3311 DNRCBM",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 2550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3311 DNRCBM is SKF's 55 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 55×120×49.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 55×120×49.2 mm (2.165×4.724×1.937 in), 32.5 mm radial section height, C 95.6 kN, C0 83 kN, Pu 3.55 kN.reference speed 5,000 r/min (thermal) and limiting speed 5,300 r/min (mechanical), catalogue mass 2550 g. Load balance: C0 83 kN against C 95.6 kN gives a 0.87 ratio, typical of a double-row bidirectional design; Pu 3.55 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 5,000 r/min reference; at dm ≈ 87.5 mm the corresponding dn is approximately 464k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 5,300 r/min limiting speed, i.e. a reference-to-limit ratio of 0.94.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "snap-ring groove distress or ring rotation if the NR snap ring is not seated fully in its groove",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Catalogue ratings of 95.6/83 kN apply to the DNRCBM execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The double-row 3311 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Compared with a single-row pair of the same bore, the double-row 3311 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3311 DNRCBM as the double d nr cb m execution; the other order numbers of the 3311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3311-DNRCBM?",
        "a": "3311 DNRCBM measures 55 mm bore × 120 mm OD × 49.2 mm width (2.165 × 4.724 × 1.937 in), mass about 2550 g. SKF 17000 ratings: C 95.6 kN, C0 83 kN, Pu 3.55 kN, reference speed 5,000 r/min (thermal) and limiting speed 5,300 r/min (mechanical)."
      },
      {
        "q": "What does the DNRCBM suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Does the 3311 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 55 mm shaft and H7 in the 120 mm housing; check the wide ring seats square because the 49.2 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3311-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 111/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (95.6/83 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3311-DNRCBM",
      "3311 DNRCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3311-DMA",
    "brand": "SKF",
    "manufacturer_designation": "3311 DMA",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 111,
    "static_load_kN": 100,
    "fatigue_load_limit_kN": 4.3,
    "reference_speed_rpm": 4800,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 2800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3311 DMA is SKF's 55 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 55×120×49.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage. Envelope 55×120×49.2 mm (2.165×4.724×1.937 in), 32.5 mm radial section height, C 111 kN, C0 100 kN, Pu 4.3 kN.reference speed 4,800 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 2800 g. Sizing arithmetic on the 55 mm bore: 111 kN C divided by the 32.5 mm radial section height gives 3.4 kN per section millimetre; the 2800 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 49.2 mm width over a 32.5 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 2800 g for 111 kN of dynamic capacity — about 25 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 4,800 r/min against a 5,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.96. Split-ring execution note: DMA combines the two-piece inner ring (used to simplify mounting of the wide 33-series section) with a machined brass cage guided on the outer ring (MA rather than ball-centred M); outer-ring guidance steadies the cage in the heavy section at the cost of a different lubrication requirement at the guide land.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "uneven loading of the split inner-ring halves if the MA cage guide land runs dry",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Compared with a single-row pair of the same bore, the double-row 3311 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3311-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Compared with a single-row pair of the same bore, the double-row 3311 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3311 DMA as the double d ma execution; the other order numbers of the 3311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3311-DMA?",
        "a": "3311 DMA measures 55 mm bore × 120 mm OD × 49.2 mm width (2.165 × 4.724 × 1.937 in), mass about 2800 g. SKF 17000 ratings: C 111 kN, C0 100 kN, Pu 4.3 kN, reference speed 4,800 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the DMA suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. DMA pairs the split inner ring with a machined brass outer-ring-centred MA cage."
      },
      {
        "q": "Why choose the double-row 3311 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in DMA?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3311-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (111/100 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (111/100 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-ATN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (111/100 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (111/100 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A-2RS1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (111/100 kN vs 112/81.5 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3311-DMA",
      "3311 DMA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3311-A",
    "brand": "SKF",
    "manufacturer_designation": "3311 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 112,
    "static_load_kN": 81.5,
    "fatigue_load_limit_kN": 3.45,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3311 A is SKF's 55 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 55×120×49.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 55×120×49.2 mm (2.165×4.724×1.937 in), 32.5 mm radial section height, C 112 kN, C0 81.5 kN, Pu 3.45 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. At the printed limiting speed of 5,300 r/min the mean pitch diameter dm ≈ 87.5 mm implies a dn value around 464k mm·r/min; the 5,300 r/min reference speed is the thermal-planning figure under catalogue load. Selection figures for 3311 A: the static-to-dynamic ratio C0/C is 0.73, Pu 3.45 kN is about 3 % of C, and catalogue mass works out to roughly 48 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,300 r/min against a 5,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.00.",
    "applications": [
      "printing and converting machinery",
      "gearbox input and output shafts with bidirectional thrust",
      "two-direction thrust positions without room for a paired single-row set"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The double-row 3311 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings of 112/81.5 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Compared with a single-row pair of the same bore, the double-row 3311 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Compared with a single-row pair of the same bore, the double-row 3311 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3311 A as the double a steel execution; the other order numbers of the 3311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3311-A?",
        "a": "3311 A measures 55 mm bore × 120 mm OD × 49.2 mm width (2.165 × 4.724 × 1.937 in), mass about 2650 g. SKF 17000 ratings: C 112 kN, C0 81.5 kN, Pu 3.45 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3311 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3311-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 111/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3311-A",
      "3311 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3311-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3311 ATN9",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 112,
    "static_load_kN": 81.5,
    "fatigue_load_limit_kN": 3.45,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3311 ATN9 is SKF's 55 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 55×120×49.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 55×120×49.2 mm (2.165×4.724×1.937 in), 32.5 mm radial section height, C 112 kN, C0 81.5 kN, Pu 3.45 kN.reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,300 r/min while thermal balance under catalogue load sets the 5,300 r/min reference; at dm ≈ 87.5 mm the corresponding dn is approximately 464k mm·r/min. Selection figures for 3311 ATN9: the static-to-dynamic ratio C0/C is 0.73, Pu 3.45 kN is about 3 % of C, and catalogue mass works out to roughly 48 g per millimetre of bore. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 49.2 mm width gives a bore/width ratio of 1.12; use these ratios when housing space around the 55 mm shaft is the first constraint.",
    "applications": [
      "two-direction thrust positions without room for a paired single-row set",
      "centrifugal pump shafts",
      "elevator and hoist machinery"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 55 mm bore); the wide 49.2 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Compared with a single-row pair of the same bore, the double-row 3311 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The double-row 3311 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings of 112/81.5 kN apply to the ATN9 execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3311 ATN9 as the double atn9 execution; the other order numbers of the 3311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3311-ATN9?",
        "a": "3311 ATN9 measures 55 mm bore × 120 mm OD × 49.2 mm width (2.165 × 4.724 × 1.937 in), mass about 2650 g. SKF 17000 ratings: C 112 kN, C0 81.5 kN, Pu 3.45 kN, reference speed 5,300 r/min (thermal) and limiting speed 5,300 r/min (mechanical), which coincide for this size."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "What does the D mean in ATN9?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3311 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3311-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 111/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3311-ATN9",
      "3311 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3212-A",
    "brand": "SKF",
    "manufacturer_designation": "3212 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 58.5,
    "fatigue_load_limit_kN": 2.5,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3212 A is SKF's 60 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 60×110×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 60×110×36.5 mm (2.362×4.331×1.437 in), 25.0 mm radial section height, C 73.5 kN, C0 58.5 kN, Pu 2.5 kN.reference speed 6,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 1200 g. Envelope economics: the 36.5 mm width over a 25.0 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 1200 g for 73.5 kN of dynamic capacity — about 16 g per rated kN. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 85.0 mm implies a dn value around 476k mm·r/min; the 6,300 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 36.5 mm width gives a bore/width ratio of 1.64; use these ratios when housing space around the 60 mm shaft is the first constraint.",
    "applications": [
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3212 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings of 73.5/58.5 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The double-row 3212 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3212 A as the double a steel execution; the other order numbers of the 3212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3212-A?",
        "a": "3212 A measures 60 mm bore × 110 mm OD × 36.5 mm width (2.362 × 4.331 × 1.437 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 58.5 kN, Pu 2.5 kN, reference speed 6,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the 110 mm housing; check the wide ring seats square because the 36.5 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3212 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3212-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3212-A",
      "3212 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3212-ATN9",
    "brand": "SKF",
    "manufacturer_designation": "3212 ATN9",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer_PA66",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 58.5,
    "fatigue_load_limit_kN": 2.5,
    "reference_speed_rpm": 6300,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3212 ATN9 is SKF's 60 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 60×110×36.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling. Envelope 60×110×36.5 mm (2.362×4.331×1.437 in), 25.0 mm radial section height, C 73.5 kN, C0 58.5 kN, Pu 2.5 kN.reference speed 6,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical), catalogue mass 1200 g. Envelope economics: the 36.5 mm width over a 25.0 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 1200 g for 73.5 kN of dynamic capacity — about 16 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min while thermal balance under catalogue load sets the 6,300 r/min reference; at dm ≈ 85.0 mm the corresponding dn is approximately 476k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 6,300 r/min against a 5,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.13.",
    "applications": [
      "paper-machine dryer-section gearing",
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "TN9 cage embrittlement in a hot gearbox position beyond the 120 °C polymer ceiling",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The double-row 3212 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Compared with a single-row pair of the same bore, the double-row 3212 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Interference goes on the rotating ring (about k5 at 60 mm bore); the wide 36.5 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3212 ATN9 as the double atn9 execution; the other order numbers of the 3212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3212-ATN9?",
        "a": "3212 ATN9 measures 60 mm bore × 110 mm OD × 36.5 mm width (2.362 × 4.331 × 1.437 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 58.5 kN, Pu 2.5 kN, reference speed 6,300 r/min (thermal) and limiting speed 5,600 r/min (mechanical)."
      },
      {
        "q": "What does the ATN9 suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. glass-fibre reinforced PA66 cage, ball-centred (suffix TN9), with a 120 °C continuous-temperature ceiling."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the 110 mm housing; check the wide ring seats square because the 36.5 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3212 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3212-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3212-ATN9",
      "3212 ATN9"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3312-A",
    "brand": "SKF",
    "manufacturer_designation": "3312 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 54,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 127,
    "static_load_kN": 95,
    "fatigue_load_limit_kN": 4.05,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 2800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3312 A is SKF's 60 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 60×130×54 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 60×130×54 mm (2.362×5.118×2.126 in), 35.0 mm radial section height, C 127 kN, C0 95 kN, Pu 4.05 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical), catalogue mass 2800 g. The 4.05 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 127/95 kN ratings and 2800 g mass this execution carries about 2.12 kN of C per millimetre of bore. Mass and section check: 2800 g inside the 60×130×54 mm outline leaves a 35.0 mm radial section, and the 95 kN static rating is 0.75× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 130 over bore 60 is a 2.17× step for this size, and the 54 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 60 mm shaft is the first constraint.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings of 127/95 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3312 A as the double a steel execution; the other order numbers of the 3312 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3312-A?",
        "a": "3312 A measures 60 mm bore × 130 mm OD × 54 mm width (2.362 × 5.118 × 2.126 in), mass about 2800 g. SKF 17000 ratings: C 127 kN, C0 95 kN, Pu 4.05 kN, reference speed 5,600 r/min (thermal) and limiting speed 5,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3312 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 60 mm shaft and H7 in the 130 mm housing; check the wide ring seats square because the 54 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3312-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×54 mm envelope with catalogue ratings within 10 %; 3312 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3312-A",
      "3312 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3213-A",
    "brand": "SKF",
    "manufacturer_designation": "3213 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 38.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 80.6,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 3.1,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3213 A is SKF's 65 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 65×120×38.1 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 65×120×38.1 mm (2.559×4.724×1.5 in), 27.5 mm radial section height, C 80.6 kN, C0 73.5 kN, Pu 3.1 kN.reference speed 5,600 r/min (thermal) and limiting speed 4,800 r/min (mechanical), catalogue mass 1750 g. Sizing arithmetic on the 65 mm bore: 80.6 kN C divided by the 27.5 mm radial section height gives 2.9 kN per section millimetre; the 1750 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 73.5 kN against C 80.6 kN gives a 0.91 ratio, typical of a double-row bidirectional design; Pu 3.1 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 120 over bore 65 is a 1.85× step for this size, and the 38.1 mm width gives a bore/width ratio of 1.71; use these ratios when housing space around the 65 mm shaft is the first constraint.",
    "applications": [
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing",
      "cement and mineral processing drives"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The double-row 3213 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The double-row 3213 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3213 A as the double a steel execution; the other order numbers of the 3213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3213-A?",
        "a": "3213 A measures 65 mm bore × 120 mm OD × 38.1 mm width (2.559 × 4.724 × 1.5 in), mass about 1750 g. SKF 17000 ratings: C 80.6 kN, C0 73.5 kN, Pu 3.1 kN, reference speed 5,600 r/min (thermal) and limiting speed 4,800 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3213 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the 120 mm housing; check the wide ring seats square because the 38.1 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3213-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×38.1 mm envelope with catalogue ratings within 10 %; 3213 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3213-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×38.1 mm envelope with catalogue ratings within 10 %; 3213 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3213-A",
      "3213 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3313-DNRCBM",
    "brand": "SKF",
    "manufacturer_designation": "3313 DNRCBM",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 58.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 138,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 5.1,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 4000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3313 DNRCBM is SKF's 65 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 65×140×58.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 65×140×58.7 mm (2.559×5.512×2.311 in), 37.5 mm radial section height, C 138 kN, C0 122 kN, Pu 5.1 kN.reference speed 5,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 4000 g. Sizing arithmetic on the 65 mm bore: 138 kN C divided by the 37.5 mm radial section height gives 3.7 kN per section millimetre; the 4000 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 58.7 mm width over a 37.5 mm section yields 1.57 mm of ring width per section millimetre, and the bearing weighs 4000 g for 138 kN of dynamic capacity — about 29 g per rated kN. Bore-to-OD planning: OD 140 over bore 65 is a 2.15× step for this size, and the 58.7 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 65 mm shaft is the first constraint.",
    "applications": [
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "snap-ring groove distress or ring rotation if the NR snap ring is not seated fully in its groove",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3313 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Controlled axial clearance is the heart of the design: CB denotes controlled Normal axial clearance between the two rows; check residual clearance after mounting and at operating temperature.",
      "The double-row 3313 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3313 DNRCBM as the double d nr cb m execution; the other order numbers of the 3313 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3313-DNRCBM?",
        "a": "3313 DNRCBM measures 65 mm bore × 140 mm OD × 58.7 mm width (2.559 × 5.512 × 2.311 in), mass about 4000 g. SKF 17000 ratings: C 138 kN, C0 122 kN, Pu 5.1 kN, reference speed 5,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the DNRCBM suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. D marks a two-piece (split) inner ring that simplifies mounting of the heavy 33-series section. NR adds a snap-ring groove in the outer ring supplied with the appropriate snap ring, and CB gives controlled axial clearance. DNRCBM combines the split inner ring, snap ring (NR), controlled CB clearance and a machined brass ball-centred M cage. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding."
      },
      {
        "q": "Why choose the double-row 3313 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in DNRCBM?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3313-A",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×58.7 mm envelope, but catalogue C/C0 differ between executions (138/122 kN vs 146/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3313-A-2Z",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×58.7 mm envelope, but catalogue C/C0 differ between executions (138/122 kN vs 146/110 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3313-DNRCBM",
      "3313 DNRCBM"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3313-A",
    "brand": "SKF",
    "manufacturer_designation": "3313 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 58.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 146,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.55,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 4100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3313 A is SKF's 65 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 65×140×58.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 65×140×58.7 mm (2.559×5.512×2.311 in), 37.5 mm radial section height, C 146 kN, C0 110 kN, Pu 4.55 kN.reference speed 5,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 4100 g. Selection figures for 3313 A: the static-to-dynamic ratio C0/C is 0.75, Pu 4.55 kN is about 3 % of C, and catalogue mass works out to roughly 63 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,500 r/min while thermal balance under catalogue load sets the 5,300 r/min reference; at dm ≈ 102.5 mm the corresponding dn is approximately 461k mm·r/min. Bore-to-OD planning: OD 140 over bore 65 is a 2.15× step for this size, and the 58.7 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 65 mm shaft is the first constraint.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Interference goes on the rotating ring (about k5 at 65 mm bore); the wide 58.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings of 146/110 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "A capped 3313-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3313 A as the double a steel execution; the other order numbers of the 3313 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3313-A?",
        "a": "3313 A measures 65 mm bore × 140 mm OD × 58.7 mm width (2.559 × 5.512 × 2.311 in), mass about 4100 g. SKF 17000 ratings: C 146 kN, C0 110 kN, Pu 4.55 kN, reference speed 5,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 65 mm shaft and H7 in the 140 mm housing; check the wide ring seats square because the 58.7 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3313 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3313-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×58.7 mm envelope, but catalogue C/C0 differ between executions (146/110 kN vs 138/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3313-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×58.7 mm envelope with catalogue ratings within 10 %; 3313 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3313-A",
      "3313 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3214-A",
    "brand": "SKF",
    "manufacturer_designation": "3214 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 88.4,
    "static_load_kN": 80,
    "fatigue_load_limit_kN": 3.4,
    "reference_speed_rpm": 5600,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 1900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3214 A is SKF's 70 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 70×125×39.7 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 70×125×39.7 mm (2.756×4.921×1.563 in), 27.5 mm radial section height, C 88.4 kN, C0 80 kN, Pu 3.4 kN.reference speed 5,600 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 1900 g. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 97.5 mm implies a dn value around 439k mm·r/min; the 5,600 r/min reference speed is the thermal-planning figure under catalogue load. Selection figures for 3214 A: the static-to-dynamic ratio C0/C is 0.90, Pu 3.4 kN is about 4 % of C, and catalogue mass works out to roughly 27 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,600 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.24.",
    "applications": [
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing",
      "cement and mineral processing drives"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Catalogue ratings of 88.4/80 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Interference goes on the rotating ring (about k5 at 70 mm bore); the wide 39.7 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "The double-row 3214 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3214 A as the double a steel execution; the other order numbers of the 3214 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3214-A?",
        "a": "3214 A measures 70 mm bore × 125 mm OD × 39.7 mm width (2.756 × 4.921 × 1.563 in), mass about 1900 g. SKF 17000 ratings: C 88.4 kN, C0 80 kN, Pu 3.4 kN, reference speed 5,600 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3214 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3214-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×39.7 mm envelope with catalogue ratings within 10 %; 3214 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3214-A",
      "3214 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3314-A",
    "brand": "SKF",
    "manufacturer_designation": "3314 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 63.5,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 163,
    "static_load_kN": 125,
    "fatigue_load_limit_kN": 5,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 5050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3314 A is SKF's 70 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 70×150×63.5 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 70×150×63.5 mm (2.756×5.906×2.5 in), 40.0 mm radial section height, C 163 kN, C0 125 kN, Pu 5 kN.reference speed 5,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 5050 g. Load balance: C0 125 kN against C 163 kN gives a 0.77 ratio, typical of a double-row bidirectional design; Pu 5 kN enters the SKF adjusted-life equation rather than the basic rating life. The 5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 163/125 kN ratings and 5050 g mass this execution carries about 2.33 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 5,000 r/min against a 4,300 r/min limiting speed, i.e. a reference-to-limit ratio of 1.16.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Catalogue ratings of 163/125 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "A capped 3314-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 70 mm bore); the wide 63.5 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Interference goes on the rotating ring (about k5 at 70 mm bore); the wide 63.5 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3314 A as the double a steel execution; the other order numbers of the 3314 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3314-A?",
        "a": "3314 A measures 70 mm bore × 150 mm OD × 63.5 mm width (2.756 × 5.906 × 2.5 in), mass about 5050 g. SKF 17000 ratings: C 163 kN, C0 125 kN, Pu 5 kN, reference speed 5,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3314 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3314-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×63.5 mm envelope with catalogue ratings within 10 %; 3314 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3314-A",
      "3314 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3215-A",
    "brand": "SKF",
    "manufacturer_designation": "3215 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 41.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 88,
    "fatigue_load_limit_kN": 3.75,
    "reference_speed_rpm": 5300,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 2100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3215 A is SKF's 75 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 75×130×41.3 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 75×130×41.3 mm (2.953×5.118×1.626 in), 27.5 mm radial section height, C 95.6 kN, C0 88 kN, Pu 3.75 kN.reference speed 5,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical), catalogue mass 2100 g. Mass and section check: 2100 g inside the 75×130×41.3 mm outline leaves a 27.5 mm radial section, and the 88 kN static rating is 0.92× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 75 mm bore: 95.6 kN C divided by the 27.5 mm radial section height gives 3.5 kN per section millimetre; the 2100 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 5,300 r/min against a 4,500 r/min limiting speed, i.e. a reference-to-limit ratio of 1.18.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings of 95.6/88 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Interference goes on the rotating ring (about k5 at 75 mm bore); the wide 41.3 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3215 A as the double a steel execution; the other order numbers of the 3215 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3215-A?",
        "a": "3215 A measures 75 mm bore × 130 mm OD × 41.3 mm width (2.953 × 5.118 × 1.626 in), mass about 2100 g. SKF 17000 ratings: C 95.6 kN, C0 88 kN, Pu 3.75 kN, reference speed 5,300 r/min (thermal) and limiting speed 4,500 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3215 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3215-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×41.3 mm envelope with catalogue ratings within 10 %; 3215 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3215-A",
      "3215 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3315-A",
    "brand": "SKF",
    "manufacturer_designation": "3315 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 68.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 176,
    "static_load_kN": 140,
    "fatigue_load_limit_kN": 5.5,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 5550,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3315 A is SKF's 75 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 75×160×68.3 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 75×160×68.3 mm (2.953×6.299×2.689 in), 42.5 mm radial section height, C 176 kN, C0 140 kN, Pu 5.5 kN.reference speed 4,500 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 5550 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min while thermal balance under catalogue load sets the 4,500 r/min reference; at dm ≈ 117.5 mm the corresponding dn is approximately 470k mm·r/min. Envelope economics: the 68.3 mm width over a 42.5 mm section yields 1.61 mm of ring width per section millimetre, and the bearing weighs 5550 g for 176 kN of dynamic capacity — about 32 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 4,500 r/min against a 4,000 r/min limiting speed, i.e. a reference-to-limit ratio of 1.13.",
    "applications": [
      "process pump and agitator drives",
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "A capped 3315-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 75 mm bore); the wide 68.3 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "A capped 3315-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Compared with a single-row pair of the same bore, the double-row 3315 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3315 A as the double a steel execution; the other order numbers of the 3315 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3315-A?",
        "a": "3315 A measures 75 mm bore × 160 mm OD × 68.3 mm width (2.953 × 6.299 × 2.689 in), mass about 5550 g. SKF 17000 ratings: C 176 kN, C0 140 kN, Pu 5.5 kN, reference speed 4,500 r/min (thermal) and limiting speed 4,000 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3315 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3315-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×68.3 mm envelope with catalogue ratings within 10 %; 3315 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3315-A",
      "3315 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3216-A",
    "brand": "SKF",
    "manufacturer_designation": "3216 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 106,
    "static_load_kN": 95,
    "fatigue_load_limit_kN": 3.9,
    "reference_speed_rpm": 5000,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3216 A is SKF's 80 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 80×140×44.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 80×140×44.4 mm (3.15×5.512×1.748 in), 30.0 mm radial section height, C 106 kN, C0 95 kN, Pu 3.9 kN.reference speed 5,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical), catalogue mass 2650 g. Selection figures for 3216 A: the static-to-dynamic ratio C0/C is 0.90, Pu 3.9 kN is about 4 % of C, and catalogue mass works out to roughly 33 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,300 r/min while thermal balance under catalogue load sets the 5,000 r/min reference; at dm ≈ 110.0 mm the corresponding dn is approximately 473k mm·r/min. Bore-to-OD planning: OD 140 over bore 80 is a 1.75× step for this size, and the 44.4 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 80 mm shaft is the first constraint.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Catalogue ratings of 106/95 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Compared with a single-row pair of the same bore, the double-row 3216 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Interference goes on the rotating ring (about k5 at 80 mm bore); the wide 44.4 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3216 A as the double a steel execution; the other order numbers of the 3216 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3216-A?",
        "a": "3216 A measures 80 mm bore × 140 mm OD × 44.4 mm width (3.15 × 5.512 × 1.748 in), mass about 2650 g. SKF 17000 ratings: C 106 kN, C0 95 kN, Pu 3.9 kN, reference speed 5,000 r/min (thermal) and limiting speed 4,300 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 80 mm shaft and H7 in the 140 mm housing; check the wide ring seats square because the 44.4 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3216 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3216",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3216-A",
      "3216 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3316-A",
    "brand": "SKF",
    "manufacturer_designation": "3316 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 68.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 193,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 6,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 6800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3316 A is SKF's 80 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 80×170×68.3 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 80×170×68.3 mm (3.15×6.693×2.689 in), 45.0 mm radial section height, C 193 kN, C0 156 kN, Pu 6 kN.reference speed 4,300 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 6800 g. Sizing arithmetic on the 80 mm bore: 193 kN C divided by the 45.0 mm radial section height gives 4.3 kN per section millimetre; the 6800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 156 kN against C 193 kN gives a 0.81 ratio, typical of a double-row bidirectional design; Pu 6 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 170 over bore 80 is a 2.13× step for this size, and the 68.3 mm width gives a bore/width ratio of 1.17; use these ratios when housing space around the 80 mm shaft is the first constraint.",
    "applications": [
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives"
    ],
    "failure_modes": [
      "tilted mounting that loads one double row more heavily than the other",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "A capped 3316-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 80 mm bore); the wide 68.3 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Interference goes on the rotating ring (about k5 at 80 mm bore); the wide 68.3 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Compared with a single-row pair of the same bore, the double-row 3316 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3316 A as the double a steel execution; the other order numbers of the 3316 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3316-A?",
        "a": "3316 A measures 80 mm bore × 170 mm OD × 68.3 mm width (3.15 × 6.693 × 2.689 in), mass about 6800 g. SKF 17000 ratings: C 193 kN, C0 156 kN, Pu 6 kN, reference speed 4,300 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3316 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 80 mm shaft and H7 in the 170 mm housing; check the wide ring seats square because the 68.3 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3316",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3316-A",
      "3316 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3217-A",
    "brand": "SKF",
    "manufacturer_designation": "3217 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 124,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.4,
    "reference_speed_rpm": 4500,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 3400,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3217 A is SKF's 85 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 85×150×49.2 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 85×150×49.2 mm (3.346×5.906×1.937 in), 32.5 mm radial section height, C 124 kN, C0 110 kN, Pu 4.4 kN.reference speed 4,500 r/min (thermal) and limiting speed 3,800 r/min (mechanical), catalogue mass 3400 g. The 4.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 124/110 kN ratings and 3400 g mass this execution carries about 1.46 kN of C per millimetre of bore. Mass and section check: 3400 g inside the 85×150×49.2 mm outline leaves a 32.5 mm radial section, and the 110 kN static rating is 0.89× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 150 over bore 85 is a 1.76× step for this size, and the 49.2 mm width gives a bore/width ratio of 1.73; use these ratios when housing space around the 85 mm shaft is the first constraint.",
    "applications": [
      "paper-machine dryer-section gearing",
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust"
    ],
    "failure_modes": [
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "tilted mounting that loads one double row more heavily than the other",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "A capped 3217-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3217-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3217-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The double-row 3217 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3217 A as the double a steel execution; the other order numbers of the 3217 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3217-A?",
        "a": "3217 A measures 85 mm bore × 150 mm OD × 49.2 mm width (3.346 × 5.906 × 1.937 in), mass about 3400 g. SKF 17000 ratings: C 124 kN, C0 110 kN, Pu 4.4 kN, reference speed 4,500 r/min (thermal) and limiting speed 3,800 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3217 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 85 mm shaft and H7 in the 150 mm housing; check the wide ring seats square because the 49.2 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3217",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3217-A",
      "3217 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3317-A",
    "brand": "SKF",
    "manufacturer_designation": "3317 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 73,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 208,
    "static_load_kN": 176,
    "fatigue_load_limit_kN": 6.55,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 8300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3317 A is SKF's 85 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 85×180×73 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 85×180×73 mm (3.346×7.087×2.874 in), 47.5 mm radial section height, C 208 kN, C0 176 kN, Pu 6.55 kN.reference speed 4,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 8300 g. Envelope economics: the 73 mm width over a 47.5 mm section yields 1.54 mm of ring width per section millimetre, and the bearing weighs 8300 g for 208 kN of dynamic capacity — about 40 g per rated kN. At the printed limiting speed of 3,600 r/min the mean pitch diameter dm ≈ 132.5 mm implies a dn value around 477k mm·r/min; the 4,000 r/min reference speed is the thermal-planning figure under catalogue load. Bore-to-OD planning: OD 180 over bore 85 is a 2.12× step for this size, and the 73 mm width gives a bore/width ratio of 1.16; use these ratios when housing space around the 85 mm shaft is the first constraint.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The double-row 3317 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings of 208/176 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "The double-row 3317 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3317 A as the double a steel execution; the other order numbers of the 3317 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3317-A?",
        "a": "3317 A measures 85 mm bore × 180 mm OD × 73 mm width (3.346 × 7.087 × 2.874 in), mass about 8300 g. SKF 17000 ratings: C 208 kN, C0 176 kN, Pu 6.55 kN, reference speed 4,000 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly k5 on the 85 mm shaft and H7 in the 180 mm housing; check the wide ring seats square because the 73 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3317 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3317",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3317-A",
      "3317 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3218-A",
    "brand": "SKF",
    "manufacturer_designation": "3218 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 52.4,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 130,
    "static_load_kN": 120,
    "fatigue_load_limit_kN": 4.55,
    "reference_speed_rpm": 4300,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 4150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3218 A is SKF's 90 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 90×160×52.4 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 90×160×52.4 mm (3.543×6.299×2.063 in), 35.0 mm radial section height, C 130 kN, C0 120 kN, Pu 4.55 kN.reference speed 4,300 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 4150 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,600 r/min while thermal balance under catalogue load sets the 4,300 r/min reference; at dm ≈ 125.0 mm the corresponding dn is approximately 450k mm·r/min. Envelope economics: the 52.4 mm width over a 35.0 mm section yields 1.50 mm of ring width per section millimetre, and the bearing weighs 4150 g for 130 kN of dynamic capacity — about 32 g per rated kN. Speed-ratio note for this exact unit: the reference speed is 4,300 r/min against a 3,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.19.",
    "applications": [
      "process pump and agitator drives",
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "A capped 3218-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3218-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3218-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The double-row 3218 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3218 A as the double a steel execution; the other order numbers of the 3218 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3218-A?",
        "a": "3218 A measures 90 mm bore × 160 mm OD × 52.4 mm width (3.543 × 6.299 × 2.063 in), mass about 4150 g. SKF 17000 ratings: C 130 kN, C0 120 kN, Pu 4.55 kN, reference speed 4,300 r/min (thermal) and limiting speed 3,600 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3218 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3218",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3218-A",
      "3218 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3318-A",
    "brand": "SKF",
    "manufacturer_designation": "3318 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 73,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 208,
    "static_load_kN": 180,
    "fatigue_load_limit_kN": 6.4,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 9250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3318 A is SKF's 90 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 90×190×73 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 90×190×73 mm (3.543×7.48×2.874 in), 50.0 mm radial section height, C 208 kN, C0 180 kN, Pu 6.4 kN.reference speed 3,800 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 9250 g. Mass and section check: 9250 g inside the 90×190×73 mm outline leaves a 50.0 mm radial section, and the 180 kN static rating is 0.87× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 90 mm bore: 208 kN C divided by the 50.0 mm radial section height gives 4.2 kN per section millimetre; the 9250 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 3,400 r/min limiting speed, i.e. a reference-to-limit ratio of 1.12.",
    "applications": [
      "process pump and agitator drives",
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings of 208/180 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3318 A as the double a steel execution; the other order numbers of the 3318 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3318-A?",
        "a": "3318 A measures 90 mm bore × 190 mm OD × 73 mm width (3.543 × 7.48 × 2.874 in), mass about 9250 g. SKF 17000 ratings: C 208 kN, C0 180 kN, Pu 6.4 kN, reference speed 3,800 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3318 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3318",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3318-A",
      "3318 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3219-A",
    "brand": "SKF",
    "manufacturer_designation": "3219 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 55.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 159,
    "static_load_kN": 146,
    "fatigue_load_limit_kN": 5.4,
    "reference_speed_rpm": 4000,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 5000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3219 A is SKF's 95 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 95×170×55.6 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 95×170×55.6 mm (3.74×6.693×2.189 in), 37.5 mm radial section height, C 159 kN, C0 146 kN, Pu 5.4 kN.reference speed 4,000 r/min (thermal) and limiting speed 3,400 r/min (mechanical), catalogue mass 5000 g. Load balance: C0 146 kN against C 159 kN gives a 0.92 ratio, typical of a double-row bidirectional design; Pu 5.4 kN enters the SKF adjusted-life equation rather than the basic rating life. The 5.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 159/146 kN ratings and 5000 g mass this execution carries about 1.67 kN of C per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 4,000 r/min against a 3,400 r/min limiting speed, i.e. a reference-to-limit ratio of 1.18.",
    "applications": [
      "process pump and agitator drives",
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "A capped 3219-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Compared with a single-row pair of the same bore, the double-row 3219 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Catalogue ratings of 159/146 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3219 A as the double a steel execution; the other order numbers of the 3219 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3219-A?",
        "a": "3219 A measures 95 mm bore × 170 mm OD × 55.6 mm width (3.74 × 6.693 × 2.189 in), mass about 5000 g. SKF 17000 ratings: C 159 kN, C0 146 kN, Pu 5.4 kN, reference speed 4,000 r/min (thermal) and limiting speed 3,400 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3219 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3219",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3219-A",
      "3219 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3319-A",
    "brand": "SKF",
    "manufacturer_designation": "3319 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 77.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 240,
    "static_load_kN": 216,
    "fatigue_load_limit_kN": 7.5,
    "reference_speed_rpm": 3600,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 11000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3319 A is SKF's 95 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 95×200×77.8 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 95×200×77.8 mm (3.74×7.874×3.063 in), 52.5 mm radial section height, C 240 kN, C0 216 kN, Pu 7.5 kN.reference speed 3,600 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 11000 g. At the printed limiting speed of 3,200 r/min the mean pitch diameter dm ≈ 147.5 mm implies a dn value around 472k mm·r/min; the 3,600 r/min reference speed is the thermal-planning figure under catalogue load. Selection figures for 3319 A: the static-to-dynamic ratio C0/C is 0.90, Pu 7.5 kN is about 3 % of C, and catalogue mass works out to roughly 116 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 3,600 r/min against a 3,200 r/min limiting speed, i.e. a reference-to-limit ratio of 1.13.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about k5 at 95 mm bore); the wide 77.8 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings of 240/216 kN apply to the A execution; the D and DNRCBM two-piece-ring executions carry their own figures on their own pages.",
      "A capped 3319-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "The double-row 3319 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3319 A as the double a steel execution; the other order numbers of the 3319 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3319-A?",
        "a": "3319 A measures 95 mm bore × 200 mm OD × 77.8 mm width (3.74 × 7.874 × 3.063 in), mass about 11000 g. SKF 17000 ratings: C 240 kN, C0 216 kN, Pu 7.5 kN, reference speed 3,600 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3319 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3319",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3319-A",
      "3319 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3220-A",
    "brand": "SKF",
    "manufacturer_designation": "3220 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 60.3,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 178,
    "static_load_kN": 166,
    "fatigue_load_limit_kN": 6,
    "reference_speed_rpm": 3800,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 6100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3220 A is SKF's 100 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 100×180×60.3 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 100×180×60.3 mm (3.937×7.087×2.374 in), 40.0 mm radial section height, C 178 kN, C0 166 kN, Pu 6 kN.reference speed 3,800 r/min (thermal) and limiting speed 3,200 r/min (mechanical), catalogue mass 6100 g. Load balance: C0 166 kN against C 178 kN gives a 0.93 ratio, typical of a double-row bidirectional design; Pu 6 kN enters the SKF adjusted-life equation rather than the basic rating life. Sizing arithmetic on the 100 mm bore: 178 kN C divided by the 40.0 mm radial section height gives 4.5 kN per section millimetre; the 6100 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 180 over bore 100 is a 1.80× step for this size, and the 60.3 mm width gives a bore/width ratio of 1.66; use these ratios when housing space around the 100 mm shaft is the first constraint.",
    "applications": [
      "process pump and agitator drives",
      "crane and winch gearboxes",
      "paper-machine dryer-section gearing"
    ],
    "failure_modes": [
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Interference goes on the rotating ring (about k5 at 100 mm bore); the wide 60.3 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "A capped 3220-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "A capped 3220-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3220 A as the double a steel execution; the other order numbers of the 3220 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3220-A?",
        "a": "3220 A measures 100 mm bore × 180 mm OD × 60.3 mm width (3.937 × 7.087 × 2.374 in), mass about 6100 g. SKF 17000 ratings: C 178 kN, C0 166 kN, Pu 6 kN, reference speed 3,800 r/min (thermal) and limiting speed 3,200 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Why choose the double-row 3220 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3220",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3220-A",
      "3220 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3320-A",
    "brand": "SKF",
    "manufacturer_designation": "3320 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 82.6,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 255,
    "static_load_kN": 255,
    "fatigue_load_limit_kN": 8.65,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 13500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3320 A is SKF's 100 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 100×215×82.6 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 100×215×82.6 mm (3.937×8.465×3.252 in), 57.5 mm radial section height, C 255 kN, C0 255 kN, Pu 8.65 kN.reference speed 3,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 13500 g. At the printed limiting speed of 2,800 r/min the mean pitch diameter dm ≈ 157.5 mm implies a dn value around 441k mm·r/min; the 3,400 r/min reference speed is the thermal-planning figure under catalogue load. Envelope economics: the 82.6 mm width over a 57.5 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 13500 g for 255 kN of dynamic capacity — about 53 g per rated kN. Bore-to-OD planning: OD 215 over bore 100 is a 2.15× step for this size, and the 82.6 mm width gives a bore/width ratio of 1.21; use these ratios when housing space around the 100 mm shaft is the first constraint.",
    "applications": [
      "paper-machine dryer-section gearing",
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust"
    ],
    "failure_modes": [
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Compared with a single-row pair of the same bore, the double-row 3320 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Compared with a single-row pair of the same bore, the double-row 3320 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "A capped 3320-2Z/-2RS1 execution of this envelope exists for sealed-for-life duty; an open double-row bearing needs application sealing and a defined lubricant supply.",
      "Interference goes on the rotating ring (about k5 at 100 mm bore); the wide 82.6 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3320 A as the double a steel execution; the other order numbers of the 3320 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3320-A?",
        "a": "3320 A measures 100 mm bore × 215 mm OD × 82.6 mm width (3.937 × 8.465 × 3.252 in), mass about 13500 g. SKF 17000 ratings: C 255 kN, C0 255 kN, Pu 8.65 kN, reference speed 3,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "What does the D mean in A?",
        "a": "D marks a two-piece inner ring, used on the heavy 33-series executions to simplify mounting; the rest of the suffix identifies the cage (MA brass outer-ring-centred, M brass ball-centred, J1 stamped steel, TN9 PA66) and snap-ring/clearance options (NR, CB)."
      },
      {
        "q": "Does the 3320 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3320",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3320-A",
      "3320 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3222-A",
    "brand": "SKF",
    "manufacturer_designation": "3222 A",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 69.8,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 212,
    "static_load_kN": 212,
    "fatigue_load_limit_kN": 7.2,
    "reference_speed_rpm": 3400,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 8800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3222 A is SKF's 110 mm-bore double-row angular-contact ball bearing of the 3200 series — two ball rows back-to-back for two-direction axial location in one unit, 110×200×69.8 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 110×200×69.8 mm (4.331×7.874×2.748 in), 45.0 mm radial section height, C 212 kN, C0 212 kN, Pu 7.2 kN.reference speed 3,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical), catalogue mass 8800 g. Sizing arithmetic on the 110 mm bore: 212 kN C divided by the 45.0 mm radial section height gives 4.7 kN per section millimetre; the 8800 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Mass and section check: 8800 g inside the 110×200×69.8 mm outline leaves a 45.0 mm radial section, and the 212 kN static rating is 1.00× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: the reference speed is 3,400 r/min against a 2,800 r/min limiting speed, i.e. a reference-to-limit ratio of 1.21.",
    "applications": [
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives",
      "crane and winch gearboxes"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Interference goes on the rotating ring (about m6 at 110 mm bore); the wide 69.8 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Controlled axial clearance is the heart of the design: the A execution is produced to the standard double-row axial clearance; check residual clearance after mounting and at operating temperature.",
      "Compared with a single-row pair of the same bore, the double-row 3222 occupies less axial space but offers less freedom to adjust preload — do not substitute without re-checking the arrangement.",
      "Interference goes on the rotating ring (about m6 at 110 mm bore); the wide 69.8 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3222 A as the double a steel execution; the other order numbers of the 3222 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3222-A?",
        "a": "3222 A measures 110 mm bore × 200 mm OD × 69.8 mm width (4.331 × 7.874 × 2.748 in), mass about 8800 g. SKF 17000 ratings: C 212 kN, C0 212 kN, Pu 7.2 kN, reference speed 3,400 r/min (thermal) and limiting speed 2,800 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Does the 3222 double-row bearing need pairing?",
        "a": "No — both ball rows are built into one bearing, so bidirectional location does not require a second unit. Controlled axial clearance is part of the design rather than a field adjustment."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly m6 on the 110 mm shaft and H7 in the 200 mm housing; check the wide ring seats square because the 69.8 mm width is sensitive to tilt."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3222",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3222-A",
      "3222 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3322-A",
    "brand": "SKF",
    "manufacturer_designation": "3322 A",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 92.1,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 291,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 9.8,
    "reference_speed_rpm": 3000,
    "limiting_speed_rpm": 2600,
    "max_rpm": 2600,
    "weight_g": 19000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3322 A is SKF's 110 mm-bore double-row angular-contact ball bearing of the 3300 series — two ball rows back-to-back for two-direction axial location in one unit, 110×240×92.1 mm. A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage. Envelope 110×240×92.1 mm (4.331×9.449×3.626 in), 65.0 mm radial section height, C 291 kN, C0 305 kN, Pu 9.8 kN.reference speed 3,000 r/min (thermal) and limiting speed 2,600 r/min (mechanical), catalogue mass 19000 g. Selection figures for 3322 A: the static-to-dynamic ratio C0/C is 1.05, Pu 9.8 kN is about 3 % of C, and catalogue mass works out to roughly 173 g per millimetre of bore. At the printed limiting speed of 2,600 r/min the mean pitch diameter dm ≈ 175.0 mm implies a dn value around 455k mm·r/min; the 3,000 r/min reference speed is the thermal-planning figure under catalogue load. Speed-ratio note for this exact unit: the reference speed is 3,000 r/min against a 2,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.15.",
    "applications": [
      "cement and mineral processing drives",
      "heavy gearbox shafts carrying reversing thrust",
      "process pump and agitator drives"
    ],
    "failure_modes": [
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "stamped steel cage noise and pocket wear in marginal-lubrication starts, where a brass-cage execution would survive",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "The double-row 3322 takes thrust in both directions by itself — that is the reason to choose it over two single-row bearings: one housing bore, one fit, built-in set geometry.",
      "The D executions have a two-piece inner ring: mount both halves square to each other, never press on the outer ring, and keep the split faces clean during fitting.",
      "Interference goes on the rotating ring (about m6 at 110 mm bore); the wide 92.1 mm ring is sensitive to tilted seats, so check squareness before clamping.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3322 A as the double a steel execution; the other order numbers of the 3322 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3322-A?",
        "a": "3322 A measures 110 mm bore × 240 mm OD × 92.1 mm width (4.331 × 9.449 × 3.626 in), mass about 19000 g. SKF 17000 ratings: C 291 kN, C0 305 kN, Pu 9.8 kN, reference speed 3,000 r/min (thermal) and limiting speed 2,600 r/min (mechanical)."
      },
      {
        "q": "What does the A suffix mean?",
        "a": "A on a double-row bearing means no filling slots, so both rows carry their full ball complement in both directions. with no cage suffix the double-row A execution uses the standard stamped steel ball-centred cage."
      },
      {
        "q": "Which fits should I use?",
        "a": "With a rotating inner ring use roughly m6 on the 110 mm shaft and H7 in the 240 mm housing; check the wide ring seats square because the 92.1 mm width is sensitive to tilt."
      },
      {
        "q": "Why choose the double-row 3322 instead of two single-row bearings?",
        "a": "The double-row bearing locates the shaft in both axial directions in one unit, in one housing bore and with factory-controlled axial clearance — a more compact arrangement than a pair, with no field matching of ground faces. A single-row pair offers adjustable preload instead."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3322",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3322-A",
      "3322 A"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3200-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3200 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 7.61,
    "static_load_kN": 4.3,
    "fatigue_load_limit_kN": 0.183,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 51,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3200 A-2Z is the capped double-row angular-contact ball bearing for a 10 mm shaft, 10×30×14 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 10×30×14 mm (0.394×1.181×0.551 in), 10.0 mm radial section height, C 7.61 kN, C0 4.3 kN, Pu 0.183 kN.SKF publishes only the 24,000 r/min limiting speed for this execution, catalogue mass 51 g. Load balance: C0 4.3 kN against C 7.61 kN gives a 0.57 ratio, typical of a steep-angle axial-oriented design; Pu 0.183 kN enters the SKF adjusted-life equation rather than the basic rating life. The 0.183 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 7.61/4.3 kN ratings and 51 g mass this execution carries about 0.76 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 24,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor idlers and small drives",
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Fit and fillet rules are unchanged from the open double-row 3200: j5 on a 10 mm rotating shaft, radii clearing the chamfer.",
      "Never wash 3200-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3200 A-2Z as the double shielded execution; the other order numbers of the 3200 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3200-A-2Z?",
        "a": "3200 A-2Z measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 51 g. SKF 17000 ratings: C 7.61 kN, C0 4.3 kN, Pu 0.183 kN, SKF publishes only the 24,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3200-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3200 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3200-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×14 mm envelope with catalogue ratings within 10 %; 3200 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3200-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×14 mm envelope with catalogue ratings within 10 %; 3200 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3200-A-2Z",
      "3200 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3200-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3200 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 10,
    "D_mm": 30,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 7.61,
    "static_load_kN": 4.3,
    "fatigue_load_limit_kN": 0.183,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 51,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3200 A-2RS1 is the capped double-row angular-contact ball bearing for a 10 mm shaft, 10×30×14 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 10×30×14 mm (0.394×1.181×0.551 in), 10.0 mm radial section height, C 7.61 kN, C0 4.3 kN, Pu 0.183 kN.SKF publishes only the 17,000 r/min limiting speed for this execution, catalogue mass 51 g. Sizing arithmetic on the 10 mm bore: 7.61 kN C divided by the 10.0 mm radial section height gives 0.8 kN per section millimetre; the 51 g mass and 2 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 14 mm width over a 10.0 mm section yields 1.40 mm of ring width per section millimetre, and the bearing weighs 51 g for 7.61 kN of dynamic capacity — about 7 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 17,000 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "conveyor idlers and small drives",
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The capped speed ceiling is 17,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Fit and fillet rules are unchanged from the open double-row 3200: j5 on a 10 mm rotating shaft, radii clearing the chamfer.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3200: j5 on a 10 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3200 A-2RS1 as the double contactsealed execution; the other order numbers of the 3200 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3200-A-2RS1?",
        "a": "3200 A-2RS1 measures 10 mm bore × 30 mm OD × 14 mm width (0.394 × 1.181 × 0.551 in), mass about 51 g. SKF 17000 ratings: C 7.61 kN, C0 4.3 kN, Pu 0.183 kN, SKF publishes only the 17,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Is 3200-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 17,000 r/min."
      },
      {
        "q": "What is the difference between 3200 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3200-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×14 mm envelope with catalogue ratings within 10 %; 3200 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3200-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 10×30×14 mm envelope with catalogue ratings within 10 %; 3200 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3200-A-2RS1",
      "3200 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3201-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3201 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 10.1,
    "static_load_kN": 5.6,
    "fatigue_load_limit_kN": 0.24,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 58,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3201 A-2Z is the capped double-row angular-contact ball bearing for a 12 mm shaft, 12×32×15.9 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 12×32×15.9 mm (0.472×1.26×0.626 in), 10.0 mm radial section height, C 10.1 kN, C0 5.6 kN, Pu 0.24 kN.SKF publishes only the 22,000 r/min limiting speed for this execution, catalogue mass 58 g. At the printed limiting speed of 22,000 r/min the mean pitch diameter dm ≈ 22.0 mm implies a dn value around 484k mm·r/min; only the limiting speed is published for this execution. Selection figures for 3201 A-2Z: the static-to-dynamic ratio C0/C is 0.55, Pu 0.24 kN is about 2 % of C, and catalogue mass works out to roughly 5 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 22,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts",
      "textile and office machinery"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Open 3201 and capped 3201-A-2Z share the 12×32×15.9 mm envelope and 10.1/5.6 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Never wash 3201-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3201 A-2Z as the double shielded execution; the other order numbers of the 3201 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3201-A-2Z?",
        "a": "3201 A-2Z measures 12 mm bore × 32 mm OD × 15.9 mm width (0.472 × 1.26 × 0.626 in), mass about 58 g. SKF 17000 ratings: C 10.1 kN, C0 5.6 kN, Pu 0.24 kN, SKF publishes only the 22,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3201 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3201?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3201-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×15.9 mm envelope with catalogue ratings within 10 %; 3201 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3201-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×15.9 mm envelope with catalogue ratings within 10 %; 3201 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3201-A-2Z",
      "3201 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3201-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3201 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 12,
    "D_mm": 32,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 10.1,
    "static_load_kN": 5.6,
    "fatigue_load_limit_kN": 0.24,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 58,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3201 A-2RS1 is the capped double-row angular-contact ball bearing for a 12 mm shaft, 12×32×15.9 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 12×32×15.9 mm (0.472×1.26×0.626 in), 10.0 mm radial section height, C 10.1 kN, C0 5.6 kN, Pu 0.24 kN.SKF publishes only the 15,000 r/min limiting speed for this execution, catalogue mass 58 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 15,000 r/min and no separate thermal reference is published; at dm ≈ 22.0 mm the corresponding dn is approximately 330k mm·r/min. At the printed limiting speed of 15,000 r/min the mean pitch diameter dm ≈ 22.0 mm implies a dn value around 330k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 15,000 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "textile and office machinery",
      "conveyor idlers and small drives",
      "domestic-appliance motors"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3201: j5 on a 12 mm rotating shaft, radii clearing the chamfer.",
      "Open 3201 and capped 3201-A-2RS1 share the 12×32×15.9 mm envelope and 10.1/5.6 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Never wash 3201-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3201 A-2RS1 as the double contactsealed execution; the other order numbers of the 3201 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3201-A-2RS1?",
        "a": "3201 A-2RS1 measures 12 mm bore × 32 mm OD × 15.9 mm width (0.472 × 1.26 × 0.626 in), mass about 58 g. SKF 17000 ratings: C 10.1 kN, C0 5.6 kN, Pu 0.24 kN, SKF publishes only the 15,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What loads can 3201-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3201: C 10.1 kN, C0 5.6 kN, Pu 0.24 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3201-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 15,000 r/min."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3201-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×15.9 mm envelope with catalogue ratings within 10 %; 3201 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3201-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 12×32×15.9 mm envelope with catalogue ratings within 10 %; 3201 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3201-A-2RS1",
      "3201 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3202-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3202 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 11.2,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.285,
    "limiting_speed_rpm": 18000,
    "max_rpm": 18000,
    "weight_g": 66,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3202 A-2Z is the capped double-row angular-contact ball bearing for a 15 mm shaft, 15×35×15.9 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 15×35×15.9 mm (0.591×1.378×0.626 in), 10.0 mm radial section height, C 11.2 kN, C0 6.8 kN, Pu 0.285 kN.SKF publishes only the 18,000 r/min limiting speed for this execution, catalogue mass 66 g. The 0.285 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 11.2/6.8 kN ratings and 66 g mass this execution carries about 0.75 kN of C per millimetre of bore. Mass and section check: 66 g inside the 15×35×15.9 mm outline leaves a 10.0 mm radial section, and the 6.8 kN static rating is 0.61× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 35 over bore 15 is a 2.33× step for this size, and the 15.9 mm width gives a bore/width ratio of 0.94; use these ratios when housing space around the 15 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "maintenance-free small gear and pump shafts",
      "textile and office machinery",
      "conveyor idlers and small drives"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Open 3202 and capped 3202-A-2Z share the 15×35×15.9 mm envelope and 11.2/6.8 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Fit and fillet rules are unchanged from the open double-row 3202: j5 on a 15 mm rotating shaft, radii clearing the chamfer.",
      "Fit and fillet rules are unchanged from the open double-row 3202: j5 on a 15 mm rotating shaft, radii clearing the chamfer.",
      "Never wash 3202-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3202 A-2Z as the double shielded execution; the other order numbers of the 3202 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3202-A-2Z?",
        "a": "3202 A-2Z measures 15 mm bore × 35 mm OD × 15.9 mm width (0.591 × 1.378 × 0.626 in), mass about 66 g. SKF 17000 ratings: C 11.2 kN, C0 6.8 kN, Pu 0.285 kN, SKF publishes only the 18,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3202?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3202-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3202: C 11.2 kN, C0 6.8 kN, Pu 0.285 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3202-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×15.9 mm envelope with catalogue ratings within 10 %; 3202 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3202-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×15.9 mm envelope with catalogue ratings within 10 %; 3202 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3202-A-2Z",
      "3202 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3202-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3202 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 15.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 11.2,
    "static_load_kN": 6.8,
    "fatigue_load_limit_kN": 0.285,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 66,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3202 A-2RS1 is the capped double-row angular-contact ball bearing for a 15 mm shaft, 15×35×15.9 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 15×35×15.9 mm (0.591×1.378×0.626 in), 10.0 mm radial section height, C 11.2 kN, C0 6.8 kN, Pu 0.285 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 66 g. Load balance: C0 6.8 kN against C 11.2 kN gives a 0.61 ratio, typical of a steep-angle axial-oriented design; Pu 0.285 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 14,000 r/min and no separate thermal reference is published; at dm ≈ 25.0 mm the corresponding dn is approximately 350k mm·r/min. Bore-to-OD planning: OD 35 over bore 15 is a 2.33× step for this size, and the 15.9 mm width gives a bore/width ratio of 0.94; use these ratios when housing space around the 15 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "maintenance-free small gear and pump shafts",
      "textile and office machinery",
      "conveyor idlers and small drives"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3202-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3202 A-2RS1 as the double contactsealed execution; the other order numbers of the 3202 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3202-A-2RS1?",
        "a": "3202 A-2RS1 measures 15 mm bore × 35 mm OD × 15.9 mm width (0.591 × 1.378 × 0.626 in), mass about 66 g. SKF 17000 ratings: C 11.2 kN, C0 6.8 kN, Pu 0.285 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Can I wash or repack a capped 3202?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3202-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3202: C 11.2 kN, C0 6.8 kN, Pu 0.285 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3202-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×15.9 mm envelope with catalogue ratings within 10 %; 3202 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3202-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×35×15.9 mm envelope with catalogue ratings within 10 %; 3202 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3202-A-2RS1",
      "3202 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3302-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3302 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 15.1,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3302 A-2Z is the capped double-row angular-contact ball bearing for a 15 mm shaft, 15×42×19 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 15×42×19 mm (0.591×1.654×0.748 in), 13.5 mm radial section height, C 15.1 kN, C0 9.3 kN, Pu 0.4 kN.SKF publishes only the 16,000 r/min limiting speed for this execution, catalogue mass 130 g. Envelope economics: the 19 mm width over a 13.5 mm section yields 1.41 mm of ring width per section millimetre, and the bearing weighs 130 g for 15.1 kN of dynamic capacity — about 9 g per rated kN. At the printed limiting speed of 16,000 r/min the mean pitch diameter dm ≈ 28.5 mm implies a dn value around 456k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 42 over bore 15 is a 2.80× step for this size, and the 19 mm width gives a bore/width ratio of 0.79; use these ratios when housing space around the 15 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "textile and office machinery",
      "conveyor idlers and small drives",
      "domestic-appliance motors"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Never wash 3302-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3302 A-2Z as the double shielded execution; the other order numbers of the 3302 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3302-A-2Z?",
        "a": "3302 A-2Z measures 15 mm bore × 42 mm OD × 19 mm width (0.591 × 1.654 × 0.748 in), mass about 130 g. SKF 17000 ratings: C 15.1 kN, C0 9.3 kN, Pu 0.4 kN, SKF publishes only the 16,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3302-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3302: C 15.1 kN, C0 9.3 kN, Pu 0.4 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3302-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3302-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×19 mm envelope with catalogue ratings within 10 %; 3302 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3302-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×19 mm envelope with catalogue ratings within 10 %; 3302 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3302-A-2Z",
      "3302 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3302-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3302 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 42,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 15.1,
    "static_load_kN": 9.3,
    "fatigue_load_limit_kN": 0.4,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 130,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3302 A-2RS1 is the capped double-row angular-contact ball bearing for a 15 mm shaft, 15×42×19 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 15×42×19 mm (0.591×1.654×0.748 in), 13.5 mm radial section height, C 15.1 kN, C0 9.3 kN, Pu 0.4 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 130 g. Selection figures for 3302 A-2RS1: the static-to-dynamic ratio C0/C is 0.62, Pu 0.4 kN is about 3 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Envelope economics: the 19 mm width over a 13.5 mm section yields 1.41 mm of ring width per section millimetre, and the bearing weighs 130 g for 15.1 kN of dynamic capacity — about 9 g per rated kN. Bore-to-OD planning: OD 42 over bore 15 is a 2.80× step for this size, and the 19 mm width gives a bore/width ratio of 0.79; use these ratios when housing space around the 15 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts",
      "textile and office machinery"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3302: j5 on a 15 mm rotating shaft, radii clearing the chamfer.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3302 A-2RS1 as the double contactsealed execution; the other order numbers of the 3302 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3302-A-2RS1?",
        "a": "3302 A-2RS1 measures 15 mm bore × 42 mm OD × 19 mm width (0.591 × 1.654 × 0.748 in), mass about 130 g. SKF 17000 ratings: C 15.1 kN, C0 9.3 kN, Pu 0.4 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What is the difference between 3302 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3302?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3302-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×19 mm envelope with catalogue ratings within 10 %; 3302 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3302-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 15×42×19 mm envelope with catalogue ratings within 10 %; 3302 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3302-A-2RS1",
      "3302 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3203-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3203 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.8,
    "fatigue_load_limit_kN": 0.365,
    "limiting_speed_rpm": 16000,
    "max_rpm": 16000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3203 A-2Z is the capped double-row angular-contact ball bearing for a 17 mm shaft, 17×40×17.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 17×40×17.5 mm (0.669×1.575×0.689 in), 11.5 mm radial section height, C 14.3 kN, C0 8.8 kN, Pu 0.365 kN.SKF publishes only the 16,000 r/min limiting speed for this execution, catalogue mass 100 g. Envelope economics: the 17.5 mm width over a 11.5 mm section yields 1.52 mm of ring width per section millimetre, and the bearing weighs 100 g for 14.3 kN of dynamic capacity — about 7 g per rated kN. At the printed limiting speed of 16,000 r/min the mean pitch diameter dm ≈ 28.5 mm implies a dn value around 456k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 40 over bore 17 is a 2.35× step for this size, and the 17.5 mm width gives a bore/width ratio of 0.97; use these ratios when housing space around the 17 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "textile and office machinery",
      "conveyor idlers and small drives",
      "domestic-appliance motors"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Never wash 3203-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The capped speed ceiling is 16,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Never wash 3203-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3203 A-2Z as the double shielded execution; the other order numbers of the 3203 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3203-A-2Z?",
        "a": "3203 A-2Z measures 17 mm bore × 40 mm OD × 17.5 mm width (0.669 × 1.575 × 0.689 in), mass about 100 g. SKF 17000 ratings: C 14.3 kN, C0 8.8 kN, Pu 0.365 kN, SKF publishes only the 16,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3203-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3203: C 14.3 kN, C0 8.8 kN, Pu 0.365 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3203-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3203-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×17.5 mm envelope with catalogue ratings within 10 %; 3203 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3203-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×17.5 mm envelope with catalogue ratings within 10 %; 3203 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3203-A-2Z",
      "3203 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3203-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3203 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 17.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 14.3,
    "static_load_kN": 8.8,
    "fatigue_load_limit_kN": 0.365,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3203 A-2RS1 is the capped double-row angular-contact ball bearing for a 17 mm shaft, 17×40×17.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 17×40×17.5 mm (0.669×1.575×0.689 in), 11.5 mm radial section height, C 14.3 kN, C0 8.8 kN, Pu 0.365 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 100 g. Selection figures for 3203 A-2RS1: the static-to-dynamic ratio C0/C is 0.62, Pu 0.365 kN is about 3 % of C, and catalogue mass works out to roughly 6 g per millimetre of bore. Envelope economics: the 17.5 mm width over a 11.5 mm section yields 1.52 mm of ring width per section millimetre, and the bearing weighs 100 g for 14.3 kN of dynamic capacity — about 7 g per rated kN. Bore-to-OD planning: OD 40 over bore 17 is a 2.35× step for this size, and the 17.5 mm width gives a bore/width ratio of 0.97; use these ratios when housing space around the 17 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts",
      "textile and office machinery"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The capped speed ceiling is 12,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Never wash 3203-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3203 A-2RS1 as the double contactsealed execution; the other order numbers of the 3203 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3203-A-2RS1?",
        "a": "3203 A-2RS1 measures 17 mm bore × 40 mm OD × 17.5 mm width (0.669 × 1.575 × 0.689 in), mass about 100 g. SKF 17000 ratings: C 14.3 kN, C0 8.8 kN, Pu 0.365 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What is the difference between 3203 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3203?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3203-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×17.5 mm envelope with catalogue ratings within 10 %; 3203 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3203-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×40×17.5 mm envelope with catalogue ratings within 10 %; 3203 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3203-A-2RS1",
      "3203 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3303-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3303 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 12.7,
    "fatigue_load_limit_kN": 0.54,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3303 A-2Z is the capped double-row angular-contact ball bearing for a 17 mm shaft, 17×47×22.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 17×47×22.2 mm (0.669×1.85×0.874 in), 15.0 mm radial section height, C 21.6 kN, C0 12.7 kN, Pu 0.54 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 180 g. The 0.54 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 21.6/12.7 kN ratings and 180 g mass this execution carries about 1.27 kN of C per millimetre of bore. Mass and section check: 180 g inside the 17×47×22.2 mm outline leaves a 15.0 mm radial section, and the 12.7 kN static rating is 0.59× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 47 over bore 17 is a 2.76× step for this size, and the 22.2 mm width gives a bore/width ratio of 0.77; use these ratios when housing space around the 17 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "maintenance-free small gear and pump shafts",
      "textile and office machinery",
      "conveyor idlers and small drives"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "raceway staining from water in the lubricant during idle periods",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The capped speed ceiling is 14,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3303: j5 on a 17 mm rotating shaft, radii clearing the chamfer.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3303 A-2Z as the double shielded execution; the other order numbers of the 3303 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3303-A-2Z?",
        "a": "3303 A-2Z measures 17 mm bore × 47 mm OD × 22.2 mm width (0.669 × 1.85 × 0.874 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 12.7 kN, Pu 0.54 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3303?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3303-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3303: C 21.6 kN, C0 12.7 kN, Pu 0.54 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3303-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×22.2 mm envelope with catalogue ratings within 10 %; 3303 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3303-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×22.2 mm envelope with catalogue ratings within 10 %; 3303 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3303-A-2Z",
      "3303 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3303-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3303 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 12.7,
    "fatigue_load_limit_kN": 0.54,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3303 A-2RS1 is the capped double-row angular-contact ball bearing for a 17 mm shaft, 17×47×22.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 17×47×22.2 mm (0.669×1.85×0.874 in), 15.0 mm radial section height, C 21.6 kN, C0 12.7 kN, Pu 0.54 kN.SKF publishes only the 11,000 r/min limiting speed for this execution, catalogue mass 180 g. Load balance: C0 12.7 kN against C 21.6 kN gives a 0.59 ratio, typical of a steep-angle axial-oriented design; Pu 0.54 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 11,000 r/min and no separate thermal reference is published; at dm ≈ 32.0 mm the corresponding dn is approximately 352k mm·r/min. Bore-to-OD planning: OD 47 over bore 17 is a 2.76× step for this size, and the 22.2 mm width gives a bore/width ratio of 0.77; use these ratios when housing space around the 17 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "maintenance-free small gear and pump shafts",
      "textile and office machinery",
      "conveyor idlers and small drives"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Open 3303 and capped 3303-A-2RS1 share the 17×47×22.2 mm envelope and 21.6/12.7 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Never wash 3303-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Never wash 3303-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3303 A-2RS1 as the double contactsealed execution; the other order numbers of the 3303 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3303-A-2RS1?",
        "a": "3303 A-2RS1 measures 17 mm bore × 47 mm OD × 22.2 mm width (0.669 × 1.85 × 0.874 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 12.7 kN, Pu 0.54 kN, SKF publishes only the 11,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Can I wash or repack a capped 3303?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3303-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3303: C 21.6 kN, C0 12.7 kN, Pu 0.54 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3303-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×22.2 mm envelope with catalogue ratings within 10 %; 3303 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3303-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 17×47×22.2 mm envelope with catalogue ratings within 10 %; 3303 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3303-A-2RS1",
      "3303 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3204-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3204 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 12.9,
    "fatigue_load_limit_kN": 0.55,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3204 A-2Z is the capped double-row angular-contact ball bearing for a 20 mm shaft, 20×47×20.6 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 20×47×20.6 mm (0.787×1.85×0.811 in), 13.5 mm radial section height, C 20.4 kN, C0 12.9 kN, Pu 0.55 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 160 g. Mass and section check: 160 g inside the 20×47×20.6 mm outline leaves a 13.5 mm radial section, and the 12.9 kN static rating is 0.63× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 20 mm bore: 20.4 kN C divided by the 13.5 mm radial section height gives 1.5 kN per section millimetre; the 160 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 14,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor idlers and small drives",
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Fit and fillet rules are unchanged from the open double-row 3204: k5 on a 20 mm rotating shaft, radii clearing the chamfer.",
      "Never wash 3204-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3204 A-2Z as the double shielded execution; the other order numbers of the 3204 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3204-A-2Z?",
        "a": "3204 A-2Z measures 20 mm bore × 47 mm OD × 20.6 mm width (0.787 × 1.85 × 0.811 in), mass about 160 g. SKF 17000 ratings: C 20.4 kN, C0 12.9 kN, Pu 0.55 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3204-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3204 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3204-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3204-A-2Z",
      "3204 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3204-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3204 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 47,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 20.4,
    "static_load_kN": 12.9,
    "fatigue_load_limit_kN": 0.55,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3204 A-2RS1 is the capped double-row angular-contact ball bearing for a 20 mm shaft, 20×47×20.6 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 20×47×20.6 mm (0.787×1.85×0.811 in), 13.5 mm radial section height, C 20.4 kN, C0 12.9 kN, Pu 0.55 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 160 g. The 0.55 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 20.4/12.9 kN ratings and 160 g mass this execution carries about 1.02 kN of C per millimetre of bore. Selection figures for 3204 A-2RS1: the static-to-dynamic ratio C0/C is 0.63, Pu 0.55 kN is about 3 % of C, and catalogue mass works out to roughly 8 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 10,000 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "conveyor idlers and small drives",
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Open 3204 and capped 3204-A-2RS1 share the 20×47×20.6 mm envelope and 20.4/12.9 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3204-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Fit and fillet rules are unchanged from the open double-row 3204: k5 on a 20 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3204 A-2RS1 as the double contactsealed execution; the other order numbers of the 3204 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3204-A-2RS1?",
        "a": "3204 A-2RS1 measures 20 mm bore × 47 mm OD × 20.6 mm width (0.787 × 1.85 × 0.811 in), mass about 160 g. SKF 17000 ratings: C 20.4 kN, C0 12.9 kN, Pu 0.55 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Is 3204-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 10,000 r/min."
      },
      {
        "q": "What is the difference between 3204 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3204-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3204-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×47×20.6 mm envelope with catalogue ratings within 10 %; 3204 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3204-A-2RS1",
      "3204 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3304-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3304 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 23.6,
    "static_load_kN": 14.6,
    "fatigue_load_limit_kN": 0.62,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3304 A-2Z is the capped double-row angular-contact ball bearing for a 20 mm shaft, 20×52×22.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 20×52×22.2 mm (0.787×2.047×0.874 in), 16.0 mm radial section height, C 23.6 kN, C0 14.6 kN, Pu 0.62 kN.SKF publishes only the 13,000 r/min limiting speed for this execution, catalogue mass 220 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 13,000 r/min and no separate thermal reference is published; at dm ≈ 36.0 mm the corresponding dn is approximately 468k mm·r/min. Envelope economics: the 22.2 mm width over a 16.0 mm section yields 1.39 mm of ring width per section millimetre, and the bearing weighs 220 g for 23.6 kN of dynamic capacity — about 9 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 13,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "domestic-appliance motors",
      "maintenance-free small gear and pump shafts",
      "textile and office machinery"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Open 3304 and capped 3304-A-2Z share the 20×52×22.2 mm envelope and 23.6/14.6 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Open 3304 and capped 3304-A-2Z share the 20×52×22.2 mm envelope and 23.6/14.6 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Fit and fillet rules are unchanged from the open double-row 3304: k5 on a 20 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3304 A-2Z as the double shielded execution; the other order numbers of the 3304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3304-A-2Z?",
        "a": "3304 A-2Z measures 20 mm bore × 52 mm OD × 22.2 mm width (0.787 × 2.047 × 0.874 in), mass about 220 g. SKF 17000 ratings: C 23.6 kN, C0 14.6 kN, Pu 0.62 kN, SKF publishes only the 13,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3304 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3304?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3304-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3304-A-2Z",
      "3304 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3304-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3304 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 22.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 23.6,
    "static_load_kN": 14.6,
    "fatigue_load_limit_kN": 0.62,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 220,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3304 A-2RS1 is the capped double-row angular-contact ball bearing for a 20 mm shaft, 20×52×22.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 20×52×22.2 mm (0.787×2.047×0.874 in), 16.0 mm radial section height, C 23.6 kN, C0 14.6 kN, Pu 0.62 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 220 g. At the printed limiting speed of 9,000 r/min the mean pitch diameter dm ≈ 36.0 mm implies a dn value around 324k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min and no separate thermal reference is published; at dm ≈ 36.0 mm the corresponding dn is approximately 324k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 9,000 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "textile and office machinery",
      "conveyor idlers and small drives",
      "domestic-appliance motors"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Open 3304 and capped 3304-A-2RS1 share the 20×52×22.2 mm envelope and 23.6/14.6 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Fit and fillet rules are unchanged from the open double-row 3304: k5 on a 20 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3304 A-2RS1 as the double contactsealed execution; the other order numbers of the 3304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3304-A-2RS1?",
        "a": "3304 A-2RS1 measures 20 mm bore × 52 mm OD × 22.2 mm width (0.787 × 2.047 × 0.874 in), mass about 220 g. SKF 17000 ratings: C 23.6 kN, C0 14.6 kN, Pu 0.62 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What loads can 3304-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3304: C 23.6 kN, C0 14.6 kN, Pu 0.62 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3304-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 9,000 r/min."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3304-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3304-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×22.2 mm envelope with catalogue ratings within 10 %; 3304 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3304-A-2RS1",
      "3304 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3205-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3205 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.6,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3205 A-2Z is the capped double-row angular-contact ball bearing for a 25 mm shaft, 25×52×20.6 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 25×52×20.6 mm (0.984×2.047×0.811 in), 13.5 mm radial section height, C 21.6 kN, C0 14.3 kN, Pu 0.6 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 180 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 12,000 r/min and no separate thermal reference is published; at dm ≈ 38.5 mm the corresponding dn is approximately 462k mm·r/min. Envelope economics: the 20.6 mm width over a 13.5 mm section yields 1.53 mm of ring width per section millimetre, and the bearing weighs 180 g for 21.6 kN of dynamic capacity — about 8 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 12,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Open 3205 and capped 3205-A-2Z share the 25×52×20.6 mm envelope and 21.6/14.3 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The capped speed ceiling is 12,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "Fit and fillet rules are unchanged from the open double-row 3205: k5 on a 25 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3205 A-2Z as the double shielded execution; the other order numbers of the 3205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3205-A-2Z?",
        "a": "3205 A-2Z measures 25 mm bore × 52 mm OD × 20.6 mm width (0.984 × 2.047 × 0.811 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 14.3 kN, Pu 0.6 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3205 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3205?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3205-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3205-A-2Z",
      "3205 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3205-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3205 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 20.6,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 21.6,
    "static_load_kN": 14.3,
    "fatigue_load_limit_kN": 0.6,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3205 A-2RS1 is the capped double-row angular-contact ball bearing for a 25 mm shaft, 25×52×20.6 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 25×52×20.6 mm (0.984×2.047×0.811 in), 13.5 mm radial section height, C 21.6 kN, C0 14.3 kN, Pu 0.6 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 180 g. At the printed limiting speed of 8,500 r/min the mean pitch diameter dm ≈ 38.5 mm implies a dn value around 327k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 8,500 r/min and no separate thermal reference is published; at dm ≈ 38.5 mm the corresponding dn is approximately 327k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,500 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "conveyor drum shafts",
      "fan and blower positions",
      "material-handling equipment"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3205: k5 on a 25 mm rotating shaft, radii clearing the chamfer.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The capped speed ceiling is 8,500 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3205 A-2RS1 as the double contactsealed execution; the other order numbers of the 3205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3205-A-2RS1?",
        "a": "3205 A-2RS1 measures 25 mm bore × 52 mm OD × 20.6 mm width (0.984 × 2.047 × 0.811 in), mass about 180 g. SKF 17000 ratings: C 21.6 kN, C0 14.3 kN, Pu 0.6 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What loads can 3205-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3205: C 21.6 kN, C0 14.3 kN, Pu 0.6 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3205-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 8,500 r/min."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3205-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3205-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×52×20.6 mm envelope with catalogue ratings within 10 %; 3205 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3205-A-2RS1",
      "3205 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3305-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3305 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 32,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3305 A-2Z is the capped double-row angular-contact ball bearing for a 25 mm shaft, 25×62×25.4 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 25×62×25.4 mm (0.984×2.441×1 in), 18.5 mm radial section height, C 32 kN, C0 20.4 kN, Pu 0.865 kN.SKF publishes only the 11,000 r/min limiting speed for this execution, catalogue mass 350 g. Mass and section check: 350 g inside the 25×62×25.4 mm outline leaves a 18.5 mm radial section, and the 20.4 kN static rating is 0.64× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 25 mm bore: 32 kN C divided by the 18.5 mm radial section height gives 1.7 kN per section millimetre; the 350 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 11,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "fan and blower positions",
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3305-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Never wash 3305-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3305 A-2Z as the double shielded execution; the other order numbers of the 3305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3305-A-2Z?",
        "a": "3305 A-2Z measures 25 mm bore × 62 mm OD × 25.4 mm width (0.984 × 2.441 × 1 in), mass about 350 g. SKF 17000 ratings: C 32 kN, C0 20.4 kN, Pu 0.865 kN, SKF publishes only the 11,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3305-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3305 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3305-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3305-A-2Z",
      "3305 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3305-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3305 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 25.4,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 32,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3305 A-2RS1 is the capped double-row angular-contact ball bearing for a 25 mm shaft, 25×62×25.4 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 25×62×25.4 mm (0.984×2.441×1 in), 18.5 mm radial section height, C 32 kN, C0 20.4 kN, Pu 0.865 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 350 g. The 0.865 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 32/20.4 kN ratings and 350 g mass this execution carries about 1.28 kN of C per millimetre of bore. Selection figures for 3305 A-2RS1: the static-to-dynamic ratio C0/C is 0.64, Pu 0.865 kN is about 3 % of C, and catalogue mass works out to roughly 14 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,500 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Open 3305 and capped 3305-A-2RS1 share the 25×62×25.4 mm envelope and 32/20.4 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Never wash 3305-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Fit and fillet rules are unchanged from the open double-row 3305: k5 on a 25 mm rotating shaft, radii clearing the chamfer.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3305 A-2RS1 as the double contactsealed execution; the other order numbers of the 3305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3305-A-2RS1?",
        "a": "3305 A-2RS1 measures 25 mm bore × 62 mm OD × 25.4 mm width (0.984 × 2.441 × 1 in), mass about 350 g. SKF 17000 ratings: C 32 kN, C0 20.4 kN, Pu 0.865 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Is 3305-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 7,500 r/min."
      },
      {
        "q": "What is the difference between 3305 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3305-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3305-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×25.4 mm envelope with catalogue ratings within 10 %; 3305 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3305-A-2RS1",
      "3305 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3206-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3206 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 30,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3206 A-2Z is the capped double-row angular-contact ball bearing for a 30 mm shaft, 30×62×23.8 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 30×62×23.8 mm (1.181×2.441×0.937 in), 16.0 mm radial section height, C 30 kN, C0 20.4 kN, Pu 0.865 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 290 g. Sizing arithmetic on the 30 mm bore: 30 kN C divided by the 16.0 mm radial section height gives 1.9 kN per section millimetre; the 290 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 20.4 kN against C 30 kN gives a 0.68 ratio, typical of a steep-angle axial-oriented design; Pu 0.865 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 62 over bore 30 is a 2.07× step for this size, and the 23.8 mm width gives a bore/width ratio of 1.26; use these ratios when housing space around the 30 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives",
      "conveyor drum shafts"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Open 3206 and capped 3206-A-2Z share the 30×62×23.8 mm envelope and 30/20.4 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3206: k5 on a 30 mm rotating shaft, radii clearing the chamfer.",
      "Fit and fillet rules are unchanged from the open double-row 3206: k5 on a 30 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3206 A-2Z as the double shielded execution; the other order numbers of the 3206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3206-A-2Z?",
        "a": "3206 A-2Z measures 30 mm bore × 62 mm OD × 23.8 mm width (1.181 × 2.441 × 0.937 in), mass about 290 g. SKF 17000 ratings: C 30 kN, C0 20.4 kN, Pu 0.865 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3206?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3206-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3206: C 30 kN, C0 20.4 kN, Pu 0.865 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3206-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3206-A-2Z",
      "3206 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3206-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3206 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 23.8,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 30,
    "static_load_kN": 20.4,
    "fatigue_load_limit_kN": 0.865,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3206 A-2RS1 is the capped double-row angular-contact ball bearing for a 30 mm shaft, 30×62×23.8 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 30×62×23.8 mm (1.181×2.441×0.937 in), 16.0 mm radial section height, C 30 kN, C0 20.4 kN, Pu 0.865 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 290 g. Mass and section check: 290 g inside the 30×62×23.8 mm outline leaves a 16.0 mm radial section, and the 20.4 kN static rating is 0.68× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 46.0 mm implies a dn value around 345k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 62 over bore 30 is a 2.07× step for this size, and the 23.8 mm width gives a bore/width ratio of 1.26; use these ratios when housing space around the 30 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The capped speed ceiling is 7,500 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Never wash 3206-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Fit and fillet rules are unchanged from the open double-row 3206: k5 on a 30 mm rotating shaft, radii clearing the chamfer.",
      "Never wash 3206-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3206 A-2RS1 as the double contactsealed execution; the other order numbers of the 3206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3206-A-2RS1?",
        "a": "3206 A-2RS1 measures 30 mm bore × 62 mm OD × 23.8 mm width (1.181 × 2.441 × 0.937 in), mass about 290 g. SKF 17000 ratings: C 30 kN, C0 20.4 kN, Pu 0.865 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Can I wash or repack a capped 3206?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3206-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3206: C 30 kN, C0 20.4 kN, Pu 0.865 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3206-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3206-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×23.8 mm envelope with catalogue ratings within 10 %; 3206 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3206-A-2RS1",
      "3206 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3306-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3306 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 42.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3306 A-2Z is the capped double-row angular-contact ball bearing for a 30 mm shaft, 30×72×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 30×72×30.2 mm (1.181×2.835×1.189 in), 21.0 mm radial section height, C 42.5 kN, C0 30 kN, Pu 1.27 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 520 g. Selection figures for 3306 A-2Z: the static-to-dynamic ratio C0/C is 0.71, Pu 1.27 kN is about 3 % of C, and catalogue mass works out to roughly 17 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min and no separate thermal reference is published; at dm ≈ 51.0 mm the corresponding dn is approximately 459k mm·r/min. Bore-to-OD planning: OD 72 over bore 30 is a 2.40× step for this size, and the 30.2 mm width gives a bore/width ratio of 0.99; use these ratios when housing space around the 30 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives",
      "conveyor drum shafts"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Never wash 3306-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3306 A-2Z as the double shielded execution; the other order numbers of the 3306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3306-A-2Z?",
        "a": "3306 A-2Z measures 30 mm bore × 72 mm OD × 30.2 mm width (1.181 × 2.835 × 1.189 in), mass about 520 g. SKF 17000 ratings: C 42.5 kN, C0 30 kN, Pu 1.27 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3306-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3306: C 42.5 kN, C0 30 kN, Pu 1.27 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3306-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3306-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3306-A-2Z",
      "3306 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3306-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3306 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 42.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3306 A-2RS1 is the capped double-row angular-contact ball bearing for a 30 mm shaft, 30×72×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 30×72×30.2 mm (1.181×2.835×1.189 in), 21.0 mm radial section height, C 42.5 kN, C0 30 kN, Pu 1.27 kN.SKF publishes only the 6,300 r/min limiting speed for this execution, catalogue mass 520 g. Envelope economics: the 30.2 mm width over a 21.0 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 520 g for 42.5 kN of dynamic capacity — about 12 g per rated kN. Selection figures for 3306 A-2RS1: the static-to-dynamic ratio C0/C is 0.71, Pu 1.27 kN is about 3 % of C, and catalogue mass works out to roughly 17 g per millimetre of bore. Bore-to-OD planning: OD 72 over bore 30 is a 2.40× step for this size, and the 30.2 mm width gives a bore/width ratio of 0.99; use these ratios when housing space around the 30 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Never wash 3306-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Open 3306 and capped 3306-A-2RS1 share the 30×72×30.2 mm envelope and 42.5/30 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Open 3306 and capped 3306-A-2RS1 share the 30×72×30.2 mm envelope and 42.5/30 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3306 A-2RS1 as the double contactsealed execution; the other order numbers of the 3306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3306-A-2RS1?",
        "a": "3306 A-2RS1 measures 30 mm bore × 72 mm OD × 30.2 mm width (1.181 × 2.835 × 1.189 in), mass about 520 g. SKF 17000 ratings: C 42.5 kN, C0 30 kN, Pu 1.27 kN, SKF publishes only the 6,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What is the difference between 3306 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3306?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3306-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3306-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×30.2 mm envelope with catalogue ratings within 10 %; 3306 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3306-A-2RS1",
      "3306 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3207-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3207 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 40,
    "static_load_kN": 28,
    "fatigue_load_limit_kN": 1.18,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 440,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3207 A-2Z is the capped double-row angular-contact ball bearing for a 35 mm shaft, 35×72×27 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 35×72×27 mm (1.378×2.835×1.063 in), 18.5 mm radial section height, C 40 kN, C0 28 kN, Pu 1.18 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 440 g. Selection figures for 3207 A-2Z: the static-to-dynamic ratio C0/C is 0.70, Pu 1.18 kN is about 3 % of C, and catalogue mass works out to roughly 13 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min and no separate thermal reference is published; at dm ≈ 53.5 mm the corresponding dn is approximately 482k mm·r/min. Bore-to-OD planning: OD 72 over bore 35 is a 2.06× step for this size, and the 27 mm width gives a bore/width ratio of 1.30; use these ratios when housing space around the 35 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor drum shafts",
      "fan and blower positions",
      "material-handling equipment"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "brinelling from pressing the ring home through the balls or from static overload",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Open 3207 and capped 3207-A-2Z share the 35×72×27 mm envelope and 40/28 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Fit and fillet rules are unchanged from the open double-row 3207: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3207 A-2Z as the double shielded execution; the other order numbers of the 3207 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3207-A-2Z?",
        "a": "3207 A-2Z measures 35 mm bore × 72 mm OD × 27 mm width (1.378 × 2.835 × 1.063 in), mass about 440 g. SKF 17000 ratings: C 40 kN, C0 28 kN, Pu 1.18 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3207-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3207: C 40 kN, C0 28 kN, Pu 1.18 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3207-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3207-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3207-A-2Z",
      "3207 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3207-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3207 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 40,
    "static_load_kN": 28,
    "fatigue_load_limit_kN": 1.18,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 440,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3207 A-2RS1 is the capped double-row angular-contact ball bearing for a 35 mm shaft, 35×72×27 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 35×72×27 mm (1.378×2.835×1.063 in), 18.5 mm radial section height, C 40 kN, C0 28 kN, Pu 1.18 kN.SKF publishes only the 6,300 r/min limiting speed for this execution, catalogue mass 440 g. Envelope economics: the 27 mm width over a 18.5 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 440 g for 40 kN of dynamic capacity — about 11 g per rated kN. Selection figures for 3207 A-2RS1: the static-to-dynamic ratio C0/C is 0.70, Pu 1.18 kN is about 3 % of C, and catalogue mass works out to roughly 13 g per millimetre of bore. Bore-to-OD planning: OD 72 over bore 35 is a 2.06× step for this size, and the 27 mm width gives a bore/width ratio of 1.30; use these ratios when housing space around the 35 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "fan and blower positions",
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3207: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "The capped speed ceiling is 6,300 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Open 3207 and capped 3207-A-2RS1 share the 35×72×27 mm envelope and 40/28 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Fit and fillet rules are unchanged from the open double-row 3207: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3207 A-2RS1 as the double contactsealed execution; the other order numbers of the 3207 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3207-A-2RS1?",
        "a": "3207 A-2RS1 measures 35 mm bore × 72 mm OD × 27 mm width (1.378 × 2.835 × 1.063 in), mass about 440 g. SKF 17000 ratings: C 40 kN, C0 28 kN, Pu 1.18 kN, SKF publishes only the 6,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What is the difference between 3207 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3207?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3207-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3207-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×72×27 mm envelope with catalogue ratings within 10 %; 3207 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3207-A-2RS1",
      "3207 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3307-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3307 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 52,
    "static_load_kN": 35.5,
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3307 A-2Z is the capped double-row angular-contact ball bearing for a 35 mm shaft, 35×80×34.9 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 35×80×34.9 mm (1.378×3.15×1.374 in), 22.5 mm radial section height, C 52 kN, C0 35.5 kN, Pu 1.5 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 740 g. Sizing arithmetic on the 35 mm bore: 52 kN C divided by the 22.5 mm radial section height gives 2.3 kN per section millimetre; the 740 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 35.5 kN against C 52 kN gives a 0.68 ratio, typical of a steep-angle axial-oriented design; Pu 1.5 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 34.9 mm width gives a bore/width ratio of 1.00; use these ratios when housing space around the 35 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor drum shafts",
      "fan and blower positions",
      "material-handling equipment"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "fretting corrosion on a loose rotating shaft seat",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Fit and fillet rules are unchanged from the open double-row 3307: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "Fit and fillet rules are unchanged from the open double-row 3307: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3307 A-2Z as the double shielded execution; the other order numbers of the 3307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3307-A-2Z?",
        "a": "3307 A-2Z measures 35 mm bore × 80 mm OD × 34.9 mm width (1.378 × 3.15 × 1.374 in), mass about 740 g. SKF 17000 ratings: C 52 kN, C0 35.5 kN, Pu 1.5 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3307?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3307-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3307: C 52 kN, C0 35.5 kN, Pu 1.5 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3307-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-DJ1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52/35.5 kN vs 52.7/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3307-A-2Z",
      "3307 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3307-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3307 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 34.9,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 52,
    "static_load_kN": 35.5,
    "fatigue_load_limit_kN": 1.5,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 740,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3307 A-2RS1 is the capped double-row angular-contact ball bearing for a 35 mm shaft, 35×80×34.9 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 35×80×34.9 mm (1.378×3.15×1.374 in), 22.5 mm radial section height, C 52 kN, C0 35.5 kN, Pu 1.5 kN.SKF publishes only the 6,000 r/min limiting speed for this execution, catalogue mass 740 g. Mass and section check: 740 g inside the 35×80×34.9 mm outline leaves a 22.5 mm radial section, and the 35.5 kN static rating is 0.68× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 6,000 r/min the mean pitch diameter dm ≈ 57.5 mm implies a dn value around 345k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 34.9 mm width gives a bore/width ratio of 1.00; use these ratios when housing space around the 35 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The capped speed ceiling is 6,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Fit and fillet rules are unchanged from the open double-row 3307: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "Fit and fillet rules are unchanged from the open double-row 3307: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "Fit and fillet rules are unchanged from the open double-row 3307: k5 on a 35 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3307 A-2RS1 as the double contactsealed execution; the other order numbers of the 3307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3307-A-2RS1?",
        "a": "3307 A-2RS1 measures 35 mm bore × 80 mm OD × 34.9 mm width (1.378 × 3.15 × 1.374 in), mass about 740 g. SKF 17000 ratings: C 52 kN, C0 35.5 kN, Pu 1.5 kN, SKF publishes only the 6,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Can I wash or repack a capped 3307?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3307-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3307: C 52 kN, C0 35.5 kN, Pu 1.5 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3307-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3307-DJ1",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×34.9 mm envelope, but catalogue C/C0 differ between executions (52/35.5 kN vs 52.7/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3307-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×34.9 mm envelope with catalogue ratings within 10 %; 3307 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3307-A-2RS1",
      "3307 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3208-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3208 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 48,
    "static_load_kN": 36.5,
    "fatigue_load_limit_kN": 1.56,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3208 A-2Z is the capped double-row angular-contact ball bearing for a 40 mm shaft, 40×80×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 40×80×30.2 mm (1.575×3.15×1.189 in), 20.0 mm radial section height, C 48 kN, C0 36.5 kN, Pu 1.56 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 570 g. Load balance: C0 36.5 kN against C 48 kN gives a 0.76 ratio, typical of a steep-angle axial-oriented design; Pu 1.56 kN enters the SKF adjusted-life equation rather than the basic rating life. The 1.56 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 48/36.5 kN ratings and 570 g mass this execution carries about 1.20 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor drum shafts",
      "fan and blower positions",
      "material-handling equipment"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The capped speed ceiling is 8,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "Fit and fillet rules are unchanged from the open double-row 3208: k5 on a 40 mm rotating shaft, radii clearing the chamfer.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3208: k5 on a 40 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3208 A-2Z as the double shielded execution; the other order numbers of the 3208 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3208-A-2Z?",
        "a": "3208 A-2Z measures 40 mm bore × 80 mm OD × 30.2 mm width (1.575 × 3.15 × 1.189 in), mass about 570 g. SKF 17000 ratings: C 48 kN, C0 36.5 kN, Pu 1.56 kN, SKF publishes only the 8,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3208-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3208 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3208-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3208-A-2Z",
      "3208 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3208-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3208 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 48,
    "static_load_kN": 36.5,
    "fatigue_load_limit_kN": 1.56,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3208 A-2RS1 is the capped double-row angular-contact ball bearing for a 40 mm shaft, 40×80×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 40×80×30.2 mm (1.575×3.15×1.189 in), 20.0 mm radial section height, C 48 kN, C0 36.5 kN, Pu 1.56 kN.SKF publishes only the 5,600 r/min limiting speed for this execution, catalogue mass 570 g. Sizing arithmetic on the 40 mm bore: 48 kN C divided by the 20.0 mm radial section height gives 2.4 kN per section millimetre; the 570 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 30.2 mm width over a 20.0 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 570 g for 48 kN of dynamic capacity — about 12 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 5,600 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Open 3208 and capped 3208-A-2RS1 share the 40×80×30.2 mm envelope and 48/36.5 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Fit and fillet rules are unchanged from the open double-row 3208: k5 on a 40 mm rotating shaft, radii clearing the chamfer.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3208-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3208 A-2RS1 as the double contactsealed execution; the other order numbers of the 3208 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3208-A-2RS1?",
        "a": "3208 A-2RS1 measures 40 mm bore × 80 mm OD × 30.2 mm width (1.575 × 3.15 × 1.189 in), mass about 570 g. SKF 17000 ratings: C 48 kN, C0 36.5 kN, Pu 1.56 kN, SKF publishes only the 5,600 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Is 3208-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 5,600 r/min."
      },
      {
        "q": "What is the difference between 3208 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3208-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3208-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×80×30.2 mm envelope with catalogue ratings within 10 %; 3208 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3208-A-2RS1",
      "3208 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3308 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 64,
    "static_load_kN": 44,
    "fatigue_load_limit_kN": 1.86,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 930,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 A-2Z is the capped double-row angular-contact ball bearing for a 40 mm shaft, 40×90×36.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 64 kN, C0 44 kN, Pu 1.86 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 930 g. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 488k mm·r/min; only the limiting speed is published for this execution. Selection figures for 3308 A-2Z: the static-to-dynamic ratio C0/C is 0.69, Pu 1.86 kN is about 3 % of C, and catalogue mass works out to roughly 23 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,500 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The capped speed ceiling is 7,500 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The capped speed ceiling is 7,500 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 A-2Z as the double shielded execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-A-2Z?",
        "a": "3308 A-2Z measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 930 g. SKF 17000 ratings: C 64 kN, C0 44 kN, Pu 1.86 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3308 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3308?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 49.4/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-A-2Z",
      "3308 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3308-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3308 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 64,
    "static_load_kN": 44,
    "fatigue_load_limit_kN": 1.86,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 930,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3308 A-2RS1 is the capped double-row angular-contact ball bearing for a 40 mm shaft, 40×90×36.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 40×90×36.5 mm (1.575×3.543×1.437 in), 25.0 mm radial section height, C 64 kN, C0 44 kN, Pu 1.86 kN.SKF publishes only the 5,000 r/min limiting speed for this execution, catalogue mass 930 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,000 r/min and no separate thermal reference is published; at dm ≈ 65.0 mm the corresponding dn is approximately 325k mm·r/min. At the printed limiting speed of 5,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 325k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 5,000 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "fan and blower positions",
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Never wash 3308-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3308 A-2RS1 as the double contactsealed execution; the other order numbers of the 3308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3308-A-2RS1?",
        "a": "3308 A-2RS1 measures 40 mm bore × 90 mm OD × 36.5 mm width (1.575 × 3.543 × 1.437 in), mass about 930 g. SKF 17000 ratings: C 64 kN, C0 44 kN, Pu 1.86 kN, SKF publishes only the 5,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What loads can 3308-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3308: C 64 kN, C0 44 kN, Pu 1.86 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3308-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 5,000 r/min."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3308-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 49.4/41.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3308-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-DTN9",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×36.5 mm envelope, but catalogue C/C0 differ between executions (64/44 kN vs 68.9/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3308-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×36.5 mm envelope with catalogue ratings within 10 %; 3308 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3308-A-2RS1",
      "3308 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3209-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3209 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 51,
    "static_load_kN": 39,
    "fatigue_load_limit_kN": 1.63,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3209 A-2Z is the capped double-row angular-contact ball bearing for a 45 mm shaft, 45×85×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 45×85×30.2 mm (1.772×3.346×1.189 in), 20.0 mm radial section height, C 51 kN, C0 39 kN, Pu 1.63 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 630 g. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 488k mm·r/min; only the limiting speed is published for this execution. Selection figures for 3209 A-2Z: the static-to-dynamic ratio C0/C is 0.76, Pu 1.63 kN is about 3 % of C, and catalogue mass works out to roughly 14 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,500 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives",
      "conveyor drum shafts"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "edge loading from shaft deflection or housing misalignment",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Open 3209 and capped 3209-A-2Z share the 45×85×30.2 mm envelope and 51/39 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Never wash 3209-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3209 A-2Z as the double shielded execution; the other order numbers of the 3209 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3209-A-2Z?",
        "a": "3209 A-2Z measures 45 mm bore × 85 mm OD × 30.2 mm width (1.772 × 3.346 × 1.189 in), mass about 630 g. SKF 17000 ratings: C 51 kN, C0 39 kN, Pu 1.63 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3209 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3209?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3209-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3209-A-2Z",
      "3209 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3209-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3209 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 51,
    "static_load_kN": 39,
    "fatigue_load_limit_kN": 1.63,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 630,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3209 A-2RS1 is the capped double-row angular-contact ball bearing for a 45 mm shaft, 45×85×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 45×85×30.2 mm (1.772×3.346×1.189 in), 20.0 mm radial section height, C 51 kN, C0 39 kN, Pu 1.63 kN.SKF publishes only the 5,300 r/min limiting speed for this execution, catalogue mass 630 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,300 r/min and no separate thermal reference is published; at dm ≈ 65.0 mm the corresponding dn is approximately 345k mm·r/min. At the printed limiting speed of 5,300 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 345k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 5,300 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Never wash 3209-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Open 3209 and capped 3209-A-2RS1 share the 45×85×30.2 mm envelope and 51/39 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The capped speed ceiling is 5,300 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3209 A-2RS1 as the double contactsealed execution; the other order numbers of the 3209 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3209-A-2RS1?",
        "a": "3209 A-2RS1 measures 45 mm bore × 85 mm OD × 30.2 mm width (1.772 × 3.346 × 1.189 in), mass about 630 g. SKF 17000 ratings: C 51 kN, C0 39 kN, Pu 1.63 kN, SKF publishes only the 5,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What loads can 3209-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3209: C 51 kN, C0 39 kN, Pu 1.63 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3209-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 5,300 r/min."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3209-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3209-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×85×30.2 mm envelope with catalogue ratings within 10 %; 3209 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3209-A-2RS1",
      "3209 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3309-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3309 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 75,
    "static_load_kN": 53,
    "fatigue_load_limit_kN": 2.24,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3309 A-2Z is the capped double-row angular-contact ball bearing for a 45 mm shaft, 45×100×39.7 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 45×100×39.7 mm (1.772×3.937×1.563 in), 27.5 mm radial section height, C 75 kN, C0 53 kN, Pu 2.24 kN.SKF publishes only the 6,700 r/min limiting speed for this execution, catalogue mass 1250 g. Load balance: C0 53 kN against C 75 kN gives a 0.71 ratio, typical of a steep-angle axial-oriented design; Pu 2.24 kN enters the SKF adjusted-life equation rather than the basic rating life. The 2.24 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 75/53 kN ratings and 1250 g mass this execution carries about 1.67 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,700 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The capped speed ceiling is 6,700 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3309-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3309 A-2Z as the double shielded execution; the other order numbers of the 3309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3309-A-2Z?",
        "a": "3309 A-2Z measures 45 mm bore × 100 mm OD × 39.7 mm width (1.772 × 3.937 × 1.563 in), mass about 1250 g. SKF 17000 ratings: C 75 kN, C0 53 kN, Pu 2.24 kN, SKF publishes only the 6,700 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3309-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3309 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3309-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 61.8/52 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 79.3/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3309-A-2Z",
      "3309 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3309-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3309 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 75,
    "static_load_kN": 53,
    "fatigue_load_limit_kN": 2.24,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 1250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3309 A-2RS1 is the capped double-row angular-contact ball bearing for a 45 mm shaft, 45×100×39.7 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 45×100×39.7 mm (1.772×3.937×1.563 in), 27.5 mm radial section height, C 75 kN, C0 53 kN, Pu 2.24 kN.SKF publishes only the 4,800 r/min limiting speed for this execution, catalogue mass 1250 g. Sizing arithmetic on the 45 mm bore: 75 kN C divided by the 27.5 mm radial section height gives 2.7 kN per section millimetre; the 1250 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 39.7 mm width over a 27.5 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 1250 g for 75 kN of dynamic capacity — about 17 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,800 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The capped speed ceiling is 4,800 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Never wash 3309-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3309-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3309 A-2RS1 as the double contactsealed execution; the other order numbers of the 3309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3309-A-2RS1?",
        "a": "3309 A-2RS1 measures 45 mm bore × 100 mm OD × 39.7 mm width (1.772 × 3.937 × 1.563 in), mass about 1250 g. SKF 17000 ratings: C 75 kN, C0 53 kN, Pu 2.24 kN, SKF publishes only the 4,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Is 3309-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 4,800 r/min."
      },
      {
        "q": "What is the difference between 3309 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3309-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 61.8/52 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3309-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×39.7 mm envelope, but catalogue C/C0 differ between executions (75/53 kN vs 79.3/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3309-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×39.7 mm envelope with catalogue ratings within 10 %; 3309 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3309-A-2RS1",
      "3309 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3210-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3210 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 51,
    "static_load_kN": 42.5,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3210 A-2Z is the capped double-row angular-contact ball bearing for a 50 mm shaft, 50×90×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 50×90×30.2 mm (1.969×3.543×1.189 in), 20.0 mm radial section height, C 51 kN, C0 42.5 kN, Pu 1.8 kN.SKF publishes only the 7,000 r/min limiting speed for this execution, catalogue mass 650 g. Selection figures for 3210 A-2Z: the static-to-dynamic ratio C0/C is 0.83, Pu 1.8 kN is about 4 % of C, and catalogue mass works out to roughly 13 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,000 r/min and no separate thermal reference is published; at dm ≈ 70.0 mm the corresponding dn is approximately 490k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3210: k5 on a 50 mm rotating shaft, radii clearing the chamfer.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Open 3210 and capped 3210-A-2Z share the 50×90×30.2 mm envelope and 51/42.5 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3210 A-2Z as the double shielded execution; the other order numbers of the 3210 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3210-A-2Z?",
        "a": "3210 A-2Z measures 50 mm bore × 90 mm OD × 30.2 mm width (1.969 × 3.543 × 1.189 in), mass about 650 g. SKF 17000 ratings: C 51 kN, C0 42.5 kN, Pu 1.8 kN, SKF publishes only the 7,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3210-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3210: C 51 kN, C0 42.5 kN, Pu 1.8 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3210-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3210-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3210-A-2Z",
      "3210 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3210-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3210 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 30.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 51,
    "static_load_kN": 42.5,
    "fatigue_load_limit_kN": 1.8,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3210 A-2RS1 is the capped double-row angular-contact ball bearing for a 50 mm shaft, 50×90×30.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 50×90×30.2 mm (1.969×3.543×1.189 in), 20.0 mm radial section height, C 51 kN, C0 42.5 kN, Pu 1.8 kN.SKF publishes only the 4,800 r/min limiting speed for this execution, catalogue mass 650 g. Envelope economics: the 30.2 mm width over a 20.0 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 650 g for 51 kN of dynamic capacity — about 13 g per rated kN. Selection figures for 3210 A-2RS1: the static-to-dynamic ratio C0/C is 0.83, Pu 1.8 kN is about 4 % of C, and catalogue mass works out to roughly 13 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,800 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Never wash 3210-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The capped speed ceiling is 4,800 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Fit and fillet rules are unchanged from the open double-row 3210: k5 on a 50 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3210 A-2RS1 as the double contactsealed execution; the other order numbers of the 3210 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3210-A-2RS1?",
        "a": "3210 A-2RS1 measures 50 mm bore × 90 mm OD × 30.2 mm width (1.969 × 3.543 × 1.189 in), mass about 650 g. SKF 17000 ratings: C 51 kN, C0 42.5 kN, Pu 1.8 kN, SKF publishes only the 4,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What is the difference between 3210 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3210?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3210-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3210-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×90×30.2 mm envelope with catalogue ratings within 10 %; 3210 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3210-A-2RS1",
      "3210 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3310-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3310 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 90,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.75,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3310 A-2Z is the capped double-row angular-contact ball bearing for a 50 mm shaft, 50×110×44.4 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 50×110×44.4 mm (1.969×4.331×1.748 in), 30.0 mm radial section height, C 90 kN, C0 64 kN, Pu 2.75 kN.SKF publishes only the 6,000 r/min limiting speed for this execution, catalogue mass 1700 g. The 2.75 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 90/64 kN ratings and 1700 g mass this execution carries about 1.80 kN of C per millimetre of bore. Mass and section check: 1700 g inside the 50×110×44.4 mm outline leaves a 30.0 mm radial section, and the 64 kN static rating is 0.71× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "fan and blower positions",
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3310-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3310 A-2Z as the double shielded execution; the other order numbers of the 3310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3310-A-2Z?",
        "a": "3310 A-2Z measures 50 mm bore × 110 mm OD × 44.4 mm width (1.969 × 4.331 × 1.748 in), mass about 1700 g. SKF 17000 ratings: C 90 kN, C0 64 kN, Pu 2.75 kN, SKF publishes only the 6,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3310?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3310-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3310: C 90 kN, C0 64 kN, Pu 2.75 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3310-DNRCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 DNRCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (90/64 kN vs 93.6/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3310-A-2Z",
      "3310 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3310-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3310 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 44.4,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 90,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.75,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 1700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3310 A-2RS1 is the capped double-row angular-contact ball bearing for a 50 mm shaft, 50×110×44.4 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 50×110×44.4 mm (1.969×4.331×1.748 in), 30.0 mm radial section height, C 90 kN, C0 64 kN, Pu 2.75 kN.SKF publishes only the 4,300 r/min limiting speed for this execution, catalogue mass 1700 g. Load balance: C0 64 kN against C 90 kN gives a 0.71 ratio, typical of a steep-angle axial-oriented design; Pu 2.75 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,300 r/min and no separate thermal reference is published; at dm ≈ 80.0 mm the corresponding dn is approximately 344k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,300 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "material-handling equipment",
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The capped speed ceiling is 4,300 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Fit and fillet rules are unchanged from the open double-row 3310: k5 on a 50 mm rotating shaft, radii clearing the chamfer.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3310: k5 on a 50 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3310 A-2RS1 as the double contactsealed execution; the other order numbers of the 3310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3310-A-2RS1?",
        "a": "3310 A-2RS1 measures 50 mm bore × 110 mm OD × 44.4 mm width (1.969 × 4.331 × 1.748 in), mass about 1700 g. SKF 17000 ratings: C 90 kN, C0 64 kN, Pu 2.75 kN, SKF publishes only the 4,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Can I wash or repack a capped 3310?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3310-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3310: C 90 kN, C0 64 kN, Pu 2.75 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3310-DNRCBM",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 DNRCBM is the brass cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3310-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×44.4 mm envelope, but catalogue C/C0 differ between executions (90/64 kN vs 93.6/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3310-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×44.4 mm envelope with catalogue ratings within 10 %; 3310 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3310-A-2RS1",
      "3310 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3211-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3211 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 33.3,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 60,
    "static_load_kN": 47.5,
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3211 A-2Z is the capped double-row angular-contact ball bearing for a 55 mm shaft, 55×100×33.3 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 55×100×33.3 mm (2.165×3.937×1.311 in), 22.5 mm radial section height, C 60 kN, C0 47.5 kN, Pu 2 kN.SKF publishes only the 6,300 r/min limiting speed for this execution, catalogue mass 910 g. Sizing arithmetic on the 55 mm bore: 60 kN C divided by the 22.5 mm radial section height gives 2.7 kN per section millimetre; the 910 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 47.5 kN against C 60 kN gives a 0.79 ratio, typical of a steep-angle axial-oriented design; Pu 2 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,300 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "lifetime-lubricated electric motor and gearbox positions",
      "agricultural machinery drives",
      "conveyor drum shafts"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The capped speed ceiling is 6,300 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3211: k5 on a 55 mm rotating shaft, radii clearing the chamfer.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3211 A-2Z as the double shielded execution; the other order numbers of the 3211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3211-A-2Z?",
        "a": "3211 A-2Z measures 55 mm bore × 100 mm OD × 33.3 mm width (2.165 × 3.937 × 1.311 in), mass about 910 g. SKF 17000 ratings: C 60 kN, C0 47.5 kN, Pu 2 kN, SKF publishes only the 6,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3211?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3211-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3211: C 60 kN, C0 47.5 kN, Pu 2 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3211-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3211-A-2Z",
      "3211 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3211-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3211 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 33.3,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 60,
    "static_load_kN": 47.5,
    "fatigue_load_limit_kN": 2,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 910,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3211 A-2RS1 is the capped double-row angular-contact ball bearing for a 55 mm shaft, 55×100×33.3 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 55×100×33.3 mm (2.165×3.937×1.311 in), 22.5 mm radial section height, C 60 kN, C0 47.5 kN, Pu 2 kN.SKF publishes only the 4,500 r/min limiting speed for this execution, catalogue mass 910 g. Mass and section check: 910 g inside the 55×100×33.3 mm outline leaves a 22.5 mm radial section, and the 47.5 kN static rating is 0.79× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 77.5 mm implies a dn value around 349k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,500 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "agricultural machinery drives",
      "conveyor drum shafts",
      "fan and blower positions"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Fit and fillet rules are unchanged from the open double-row 3211: k5 on a 55 mm rotating shaft, radii clearing the chamfer.",
      "Fit and fillet rules are unchanged from the open double-row 3211: k5 on a 55 mm rotating shaft, radii clearing the chamfer.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3211 A-2RS1 as the double contactsealed execution; the other order numbers of the 3211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3211-A-2RS1?",
        "a": "3211 A-2RS1 measures 55 mm bore × 100 mm OD × 33.3 mm width (2.165 × 3.937 × 1.311 in), mass about 910 g. SKF 17000 ratings: C 60 kN, C0 47.5 kN, Pu 2 kN, SKF publishes only the 4,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Can I wash or repack a capped 3211?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3211-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3211: C 60 kN, C0 47.5 kN, Pu 2 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3211-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3211-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×33.3 mm envelope with catalogue ratings within 10 %; 3211 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3211-A-2RS1",
      "3211 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3311-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3311 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 112,
    "static_load_kN": 81.5,
    "fatigue_load_limit_kN": 3.45,
    "limiting_speed_rpm": 5300,
    "max_rpm": 5300,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3311 A-2Z is the capped double-row angular-contact ball bearing for a 55 mm shaft, 55×120×49.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 55×120×49.2 mm (2.165×4.724×1.937 in), 32.5 mm radial section height, C 112 kN, C0 81.5 kN, Pu 3.45 kN.SKF publishes only the 5,300 r/min limiting speed for this execution, catalogue mass 2650 g. Envelope economics: the 49.2 mm width over a 32.5 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 2650 g for 112 kN of dynamic capacity — about 24 g per rated kN. At the printed limiting speed of 5,300 r/min the mean pitch diameter dm ≈ 87.5 mm implies a dn value around 464k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 5,300 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor drum shafts",
      "fan and blower positions",
      "material-handling equipment"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Never wash 3311-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The capped speed ceiling is 5,300 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "Open 3311 and capped 3311-A-2Z share the 55×120×49.2 mm envelope and 112/81.5 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Never wash 3311-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3311 A-2Z as the double shielded execution; the other order numbers of the 3311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3311-A-2Z?",
        "a": "3311 A-2Z measures 55 mm bore × 120 mm OD × 49.2 mm width (2.165 × 4.724 × 1.937 in), mass about 2650 g. SKF 17000 ratings: C 112 kN, C0 81.5 kN, Pu 3.45 kN, SKF publishes only the 5,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3311-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3311: C 112 kN, C0 81.5 kN, Pu 3.45 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3311-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3311-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 111/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3311-A-2Z",
      "3311 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3311-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3311 A-2RS1",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 49.2,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 112,
    "static_load_kN": 81.5,
    "fatigue_load_limit_kN": 3.45,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 2650,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3311 A-2RS1 is the capped double-row angular-contact ball bearing for a 55 mm shaft, 55×120×49.2 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 55×120×49.2 mm (2.165×4.724×1.937 in), 32.5 mm radial section height, C 112 kN, C0 81.5 kN, Pu 3.45 kN.SKF publishes only the 3,800 r/min limiting speed for this execution, catalogue mass 2650 g. Selection figures for 3311 A-2RS1: the static-to-dynamic ratio C0/C is 0.73, Pu 3.45 kN is about 3 % of C, and catalogue mass works out to roughly 48 g per millimetre of bore. Envelope economics: the 49.2 mm width over a 32.5 mm section yields 1.51 mm of ring width per section millimetre, and the bearing weighs 2650 g for 112 kN of dynamic capacity — about 24 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 3,800 r/min limiting value is the single published ceiling. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "conveyor drum shafts",
      "fan and blower positions",
      "material-handling equipment"
    ],
    "failure_modes": [
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "tilted mounting that loads one double row more heavily than the other",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3311: k5 on a 55 mm rotating shaft, radii clearing the chamfer.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Open 3311 and capped 3311-A-2RS1 share the 55×120×49.2 mm envelope and 112/81.5 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "The contact NBR seals add drag and a lower speed ceiling: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3311 A-2RS1 as the double contactsealed execution; the other order numbers of the 3311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3311-A-2RS1?",
        "a": "3311 A-2RS1 measures 55 mm bore × 120 mm OD × 49.2 mm width (2.165 × 4.724 × 1.937 in), mass about 2650 g. SKF 17000 ratings: C 112 kN, C0 81.5 kN, Pu 3.45 kN, SKF publishes only the 3,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What is the difference between 3311 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3311?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3311-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-DMA",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×49.2 mm envelope, but catalogue C/C0 differ between executions (112/81.5 kN vs 111/100 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3311-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3311-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×49.2 mm envelope with catalogue ratings within 10 %; 3311 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3311-A-2RS1",
      "3311 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3212-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3212 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 58.5,
    "fatigue_load_limit_kN": 2.5,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3212 A-2Z is the capped double-row angular-contact ball bearing for a 60 mm shaft, 60×110×36.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 60×110×36.5 mm (2.362×4.331×1.437 in), 25.0 mm radial section height, C 73.5 kN, C0 58.5 kN, Pu 2.5 kN.SKF publishes only the 5,600 r/min limiting speed for this execution, catalogue mass 1200 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 5,600 r/min and no separate thermal reference is published; at dm ≈ 85.0 mm the corresponding dn is approximately 476k mm·r/min. Envelope economics: the 36.5 mm width over a 25.0 mm section yields 1.46 mm of ring width per section millimetre, and the bearing weighs 1200 g for 73.5 kN of dynamic capacity — about 16 g per rated kN. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 36.5 mm width gives a bore/width ratio of 1.64; use these ratios when housing space around the 60 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "crusher auxiliary drives",
      "sealed-for-life process-side gear shafts",
      "agricultural and construction machinery drives"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The capped speed ceiling is 5,600 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "Never wash 3212-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3212 A-2Z as the double shielded execution; the other order numbers of the 3212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3212-A-2Z?",
        "a": "3212 A-2Z measures 60 mm bore × 110 mm OD × 36.5 mm width (2.362 × 4.331 × 1.437 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 58.5 kN, Pu 2.5 kN, SKF publishes only the 5,600 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3212 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3212?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3212-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3212-A-2Z",
      "3212 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3212-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3212 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 36.5,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 73.5,
    "static_load_kN": 58.5,
    "fatigue_load_limit_kN": 2.5,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3212 A-2RS1 is the capped double-row angular-contact ball bearing for a 60 mm shaft, 60×110×36.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 60×110×36.5 mm (2.362×4.331×1.437 in), 25.0 mm radial section height, C 73.5 kN, C0 58.5 kN, Pu 2.5 kN.SKF publishes only the 4,000 r/min limiting speed for this execution, catalogue mass 1200 g. At the printed limiting speed of 4,000 r/min the mean pitch diameter dm ≈ 85.0 mm implies a dn value around 340k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min and no separate thermal reference is published; at dm ≈ 85.0 mm the corresponding dn is approximately 340k mm·r/min. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 36.5 mm width gives a bore/width ratio of 1.64; use these ratios when housing space around the 60 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "agricultural and construction machinery drives",
      "conveyor pulleys in dusty duty",
      "crusher auxiliary drives"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Never wash 3212-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The capped speed ceiling is 4,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "The capped speed ceiling is 4,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Never wash 3212-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3212 A-2RS1 as the double contactsealed execution; the other order numbers of the 3212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3212-A-2RS1?",
        "a": "3212 A-2RS1 measures 60 mm bore × 110 mm OD × 36.5 mm width (2.362 × 4.331 × 1.437 in), mass about 1200 g. SKF 17000 ratings: C 73.5 kN, C0 58.5 kN, Pu 2.5 kN, SKF publishes only the 4,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "What loads can 3212-A-2RS1 take?",
        "a": "The same bidirectional combined loads as the open double-row 3212: C 73.5 kN, C0 58.5 kN, Pu 2.5 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3212-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 4,000 r/min."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3212-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-ATN9",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 ATN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3212-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×36.5 mm envelope with catalogue ratings within 10 %; 3212 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3212-A-2RS1",
      "3212 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3312-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3312 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 54,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 127,
    "static_load_kN": 95,
    "fatigue_load_limit_kN": 4.05,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 2800,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3312 A-2Z is the capped double-row angular-contact ball bearing for a 60 mm shaft, 60×130×54 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 60×130×54 mm (2.362×5.118×2.126 in), 35.0 mm radial section height, C 127 kN, C0 95 kN, Pu 4.05 kN.SKF publishes only the 5,000 r/min limiting speed for this execution, catalogue mass 2800 g. Load balance: C0 95 kN against C 127 kN gives a 0.75 ratio, typical of a steep-angle axial-oriented design; Pu 4.05 kN enters the SKF adjusted-life equation rather than the basic rating life. The 4.05 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 127/95 kN ratings and 2800 g mass this execution carries about 2.12 kN of C per millimetre of bore. Bore-to-OD planning: OD 130 over bore 60 is a 2.17× step for this size, and the 54 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 60 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor pulleys in dusty duty",
      "crusher auxiliary drives",
      "sealed-for-life process-side gear shafts"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "false brinelling on the loaded row while the shaft stands idle under vibration",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "Never wash 3312-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Fit and fillet rules are unchanged from the open double-row 3312: k5 on a 60 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3312 A-2Z as the double shielded execution; the other order numbers of the 3312 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3312-A-2Z?",
        "a": "3312 A-2Z measures 60 mm bore × 130 mm OD × 54 mm width (2.362 × 5.118 × 2.126 in), mass about 2800 g. SKF 17000 ratings: C 127 kN, C0 95 kN, Pu 4.05 kN, SKF publishes only the 5,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3312-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3312 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3312-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×54 mm envelope with catalogue ratings within 10 %; 3312 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3312-A-2Z",
      "3312 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3213-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3213 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 38.1,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 80.6,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 3.1,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3213 A-2Z is the capped double-row angular-contact ball bearing for a 65 mm shaft, 65×120×38.1 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 65×120×38.1 mm (2.559×4.724×1.5 in), 27.5 mm radial section height, C 80.6 kN, C0 73.5 kN, Pu 3.1 kN.SKF publishes only the 4,800 r/min limiting speed for this execution, catalogue mass 1750 g. Mass and section check: 1750 g inside the 65×120×38.1 mm outline leaves a 27.5 mm radial section, and the 73.5 kN static rating is 0.91× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Sizing arithmetic on the 65 mm bore: 80.6 kN C divided by the 27.5 mm radial section height gives 2.9 kN per section millimetre; the 1750 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 120 over bore 65 is a 1.85× step for this size, and the 38.1 mm width gives a bore/width ratio of 1.71; use these ratios when housing space around the 65 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "conveyor pulleys in dusty duty",
      "crusher auxiliary drives",
      "sealed-for-life process-side gear shafts"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "snap-ring groove or two-piece-ring damage when the D execution is pressed home through the wrong ring",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The shields/seals do not make the bearing waterproof under immersion or pressure washing; select external sealing for wet or wash-down duty.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3213-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Never wash 3213-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3213 A-2Z as the double shielded execution; the other order numbers of the 3213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3213-A-2Z?",
        "a": "3213 A-2Z measures 65 mm bore × 120 mm OD × 38.1 mm width (2.559 × 4.724 × 1.5 in), mass about 1750 g. SKF 17000 ratings: C 80.6 kN, C0 73.5 kN, Pu 3.1 kN, SKF publishes only the 4,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Is 3213-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      },
      {
        "q": "What is the difference between 3213 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3213-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×38.1 mm envelope with catalogue ratings within 10 %; 3213 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3213-A-2RS1",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×38.1 mm envelope with catalogue ratings within 10 %; 3213 A-2RS1 is the stamped steel cage, contact NBR seals (-2RS1) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3213-A-2Z",
      "3213 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3213-A-2RS1",
    "brand": "SKF",
    "manufacturer_designation": "3213 A-2RS1",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 38.1,
    "material": "GCr15",
    "seal_type": "2RS",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 80.6,
    "static_load_kN": 73.5,
    "fatigue_load_limit_kN": 3.1,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3213 A-2RS1 is the capped double-row angular-contact ball bearing for a 65 mm shaft, 65×120×38.1 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling. Envelope 65×120×38.1 mm (2.559×4.724×1.5 in), 27.5 mm radial section height, C 80.6 kN, C0 73.5 kN, Pu 3.1 kN.SKF publishes only the 3,600 r/min limiting speed for this execution, catalogue mass 1750 g. The 3.1 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 80.6/73.5 kN ratings and 1750 g mass this execution carries about 1.24 kN of C per millimetre of bore. Selection figures for 3213 A-2RS1: the static-to-dynamic ratio C0/C is 0.91, Pu 3.1 kN is about 4 % of C, and catalogue mass works out to roughly 27 g per millimetre of bore. Bore-to-OD planning: OD 120 over bore 65 is a 1.85× step for this size, and the 38.1 mm width gives a bore/width ratio of 1.71; use these ratios when housing space around the 65 mm shaft is the first constraint. Contact-seal execution note: the two NBR -2RS1 lips ride the inner-ring lands, sealing the factory grease against moisture and fine dust; the lips add running torque and set the lower limiting speed printed for this size, and the sealed cavity is maintenance-free by design (no relubrication path). The A-2Z shielded order number is the low-drag alternative for cleaner positions.",
    "applications": [
      "conveyor pulleys in dusty duty",
      "crusher auxiliary drives",
      "sealed-for-life process-side gear shafts"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "seal-lip wear and grease loss after fine abrasive dust reaches the lip contact",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The capped speed ceiling is 3,600 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2RS1.",
      "Never wash 3213-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Never wash 3213-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Never wash 3213-A-2RS1 in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3213 A-2RS1 as the double contactsealed execution; the other order numbers of the 3213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3213-A-2RS1?",
        "a": "3213 A-2RS1 measures 65 mm bore × 120 mm OD × 38.1 mm width (2.559 × 4.724 × 1.5 in), mass about 1750 g. SKF 17000 ratings: C 80.6 kN, C0 73.5 kN, Pu 3.1 kN, SKF publishes only the 3,600 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2RS1 suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2RS1 marks a contact NBR elastomer seal on each side, riding the inner ring: better fine-dust and moisture protection than a shield at the cost of seal drag and a lower speed ceiling."
      },
      {
        "q": "Is 3213-A-2RS1 sealed for life?",
        "a": "Yes — the two -2RS1 contact NBR seals enclose a lifetime grease fill; there is no relubrication provision, and the seals cap the limiting speed at 3,600 r/min."
      },
      {
        "q": "What is the difference between 3213 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3213-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×38.1 mm envelope with catalogue ratings within 10 %; 3213 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "3213-A-2Z",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×38.1 mm envelope with catalogue ratings within 10 %; 3213 A-2Z is the stamped steel cage, shields (-2Z) execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3213-A-2RS1",
      "3213 A-2RS1"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3313-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3313 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 58.7,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 146,
    "static_load_kN": 110,
    "fatigue_load_limit_kN": 4.55,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 4100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3313 A-2Z is the capped double-row angular-contact ball bearing for a 65 mm shaft, 65×140×58.7 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 65×140×58.7 mm (2.559×5.512×2.311 in), 37.5 mm radial section height, C 146 kN, C0 110 kN, Pu 4.55 kN.SKF publishes only the 4,500 r/min limiting speed for this execution, catalogue mass 4100 g. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 461k mm·r/min; only the limiting speed is published for this execution. Selection figures for 3313 A-2Z: the static-to-dynamic ratio C0/C is 0.75, Pu 4.55 kN is about 3 % of C, and catalogue mass works out to roughly 63 g per millimetre of bore. Bore-to-OD planning: OD 140 over bore 65 is a 2.15× step for this size, and the 58.7 mm width gives a bore/width ratio of 1.11; use these ratios when housing space around the 65 mm shaft is the first constraint. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "crusher auxiliary drives",
      "sealed-for-life process-side gear shafts",
      "agricultural and construction machinery drives"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "edge loading from shaft deflection or housing misalignment",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Open 3313 and capped 3313-A-2Z share the 65×140×58.7 mm envelope and 146/110 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Open 3313 and capped 3313-A-2Z share the 65×140×58.7 mm envelope and 146/110 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Fit and fillet rules are unchanged from the open double-row 3313: k5 on a 65 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3313 A-2Z as the double shielded execution; the other order numbers of the 3313 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3313-A-2Z?",
        "a": "3313 A-2Z measures 65 mm bore × 140 mm OD × 58.7 mm width (2.559 × 5.512 × 2.311 in), mass about 4100 g. SKF 17000 ratings: C 146 kN, C0 110 kN, Pu 4.55 kN, SKF publishes only the 4,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What is the difference between 3313 A-2Z and A-2RS1?",
        "a": "Both share the double-row A geometry, dimensions and ratings; A-2Z uses non-contact metal shields (lower drag, higher speed, dust protection), A-2RS1 uses contact NBR rubber seals (better moisture and fine-dust protection, lower speed ceiling and more drag)."
      },
      {
        "q": "Can I wash or repack a capped 3313?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3313-DNRCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×58.7 mm envelope, but catalogue C/C0 differ between executions (146/110 kN vs 138/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "3313-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×58.7 mm envelope with catalogue ratings within 10 %; 3313 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3313-A-2Z",
      "3313 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3214-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3214 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 39.7,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 88.4,
    "static_load_kN": 80,
    "fatigue_load_limit_kN": 3.4,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 1900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3214 A-2Z is the capped double-row angular-contact ball bearing for a 70 mm shaft, 70×125×39.7 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 70×125×39.7 mm (2.756×4.921×1.563 in), 27.5 mm radial section height, C 88.4 kN, C0 80 kN, Pu 3.4 kN.SKF publishes only the 4,500 r/min limiting speed for this execution, catalogue mass 1900 g. Envelope economics: the 39.7 mm width over a 27.5 mm section yields 1.44 mm of ring width per section millimetre, and the bearing weighs 1900 g for 88.4 kN of dynamic capacity — about 21 g per rated kN. At the printed limiting speed of 4,500 r/min the mean pitch diameter dm ≈ 97.5 mm implies a dn value around 439k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,500 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "agricultural and construction machinery drives",
      "conveyor pulleys in dusty duty",
      "crusher auxiliary drives"
    ],
    "failure_modes": [
      "contact-seal lip hardening and grease-life expiry after long high-temperature service",
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Never wash 3214-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The capped speed ceiling is 4,500 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "Open 3214 and capped 3214-A-2Z share the 70×125×39.7 mm envelope and 88.4/80 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Never wash 3214-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3214 A-2Z as the double shielded execution; the other order numbers of the 3214 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3214-A-2Z?",
        "a": "3214 A-2Z measures 70 mm bore × 125 mm OD × 39.7 mm width (2.756 × 4.921 × 1.563 in), mass about 1900 g. SKF 17000 ratings: C 88.4 kN, C0 80 kN, Pu 3.4 kN, SKF publishes only the 4,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3214-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3214: C 88.4 kN, C0 80 kN, Pu 3.4 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3214-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3214-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×39.7 mm envelope with catalogue ratings within 10 %; 3214 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3214-A-2Z",
      "3214 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3314-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3314 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 63.5,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 163,
    "static_load_kN": 125,
    "fatigue_load_limit_kN": 5,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 5050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3314 A-2Z is the capped double-row angular-contact ball bearing for a 70 mm shaft, 70×150×63.5 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 70×150×63.5 mm (2.756×5.906×2.5 in), 40.0 mm radial section height, C 163 kN, C0 125 kN, Pu 5 kN.SKF publishes only the 4,300 r/min limiting speed for this execution, catalogue mass 5050 g. Sizing arithmetic on the 70 mm bore: 163 kN C divided by the 40.0 mm radial section height gives 4.1 kN per section millimetre; the 5050 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Load balance: C0 125 kN against C 163 kN gives a 0.77 ratio, typical of a steep-angle axial-oriented design; Pu 5 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,300 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "sealed-for-life process-side gear shafts",
      "agricultural and construction machinery drives",
      "conveyor pulleys in dusty duty"
    ],
    "failure_modes": [
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "loss of controlled axial clearance (CB) after thermal growth removes residual play",
      "fretting corrosion on a loose rotating shaft seat",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Open 3314 and capped 3314-A-2Z share the 70×150×63.5 mm envelope and 163/125 kN ratings — the choice is maintenance access and contamination, not capacity.",
      "Fit and fillet rules are unchanged from the open double-row 3314: k5 on a 70 mm rotating shaft, radii clearing the chamfer.",
      "Never wash 3314-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Never wash 3314-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3314 A-2Z as the double shielded execution; the other order numbers of the 3314 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3314-A-2Z?",
        "a": "3314 A-2Z measures 70 mm bore × 150 mm OD × 63.5 mm width (2.756 × 5.906 × 2.5 in), mass about 5050 g. SKF 17000 ratings: C 163 kN, C0 125 kN, Pu 5 kN, SKF publishes only the 4,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3314?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3314-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3314: C 163 kN, C0 125 kN, Pu 5 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3314-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×63.5 mm envelope with catalogue ratings within 10 %; 3314 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3314-A-2Z",
      "3314 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3215-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3215 A-2Z",
    "series": "3200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 41.3,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 95.6,
    "static_load_kN": 88,
    "fatigue_load_limit_kN": 3.75,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 2100,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3215 A-2Z is the capped double-row angular-contact ball bearing for a 75 mm shaft, 75×130×41.3 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 75×130×41.3 mm (2.953×5.118×1.626 in), 27.5 mm radial section height, C 95.6 kN, C0 88 kN, Pu 3.75 kN.SKF publishes only the 4,500 r/min limiting speed for this execution, catalogue mass 2100 g. The 3.75 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 95.6/88 kN ratings and 2100 g mass this execution carries about 1.27 kN of C per millimetre of bore. Mass and section check: 2100 g inside the 75×130×41.3 mm outline leaves a 27.5 mm radial section, and the 88 kN static rating is 0.92× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,500 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "sealed-for-life process-side gear shafts",
      "agricultural and construction machinery drives",
      "conveyor pulleys in dusty duty"
    ],
    "failure_modes": [
      "grease loss when the sealed-for-life cavity is overheated with no relubrication path",
      "contamination trapped for life when a capped bearing is mounted with dirty hands or tools",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "two-direction thrust overload concentrating load on one row and spalling its raceway",
      "raceway staining from water in the lubricant during idle periods",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The capped speed ceiling is 4,500 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Never wash 3215-A-2Z in solvent: the lifetime grease fill cannot be replaced once flushed out.",
      "The non-contact shields cap the speed with negligible drag: no relubrication is provided for, so mounting cleanliness decides much of the real grease life.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3215 A-2Z as the double shielded execution; the other order numbers of the 3215 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3215-A-2Z?",
        "a": "3215 A-2Z measures 75 mm bore × 130 mm OD × 41.3 mm width (2.953 × 5.118 × 1.626 in), mass about 2100 g. SKF 17000 ratings: C 95.6 kN, C0 88 kN, Pu 3.75 kN, SKF publishes only the 4,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "Can I wash or repack a capped 3215?",
        "a": "No — solvent flushes the factory grease with no way to replace it fully; keep the original protection in place and mount the bearing with clean tools."
      },
      {
        "q": "What loads can 3215-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3215: C 95.6 kN, C0 88 kN, Pu 3.75 kN. Capping changes sealing and speed, not the basic ratings."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3215-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×41.3 mm envelope with catalogue ratings within 10 %; 3215 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3215-A-2Z",
      "3215 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "3315-A-2Z",
    "brand": "SKF",
    "manufacturer_designation": "3315 A-2Z",
    "series": "3300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 68.3,
    "material": "GCr15",
    "seal_type": "ZZ",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "steel_stamped_J",
    "dynamic_load_kN": 176,
    "static_load_kN": 140,
    "fatigue_load_limit_kN": 5.5,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 5600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "3315 A-2Z is the capped double-row angular-contact ball bearing for a 75 mm shaft, 75×160×68.3 mm, greased and sealed (or shielded) for life at the SKF works. A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance. Envelope 75×160×68.3 mm (2.953×6.299×2.689 in), 42.5 mm radial section height, C 176 kN, C0 140 kN, Pu 5.5 kN.SKF publishes only the 4,000 r/min limiting speed for this execution, catalogue mass 5600 g. Selection figures for 3315 A-2Z: the static-to-dynamic ratio C0/C is 0.80, Pu 5.5 kN is about 3 % of C, and catalogue mass works out to roughly 75 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min and no separate thermal reference is published; at dm ≈ 117.5 mm the corresponding dn is approximately 470k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,000 r/min limiting value is the single published ceiling. Shielded execution note: the two sheet-metal -2Z covers clip into the outer ring without contacting the inner ring, giving grease retention and coarse-dust protection at virtually no friction; the cavity is factory-greased and the shield arrangement suits dry, moderately dusty positions rather than wash-down duty, where the A-2RS1 contact-seal order number is the alternative.",
    "applications": [
      "agricultural and construction machinery drives",
      "conveyor pulleys in dusty duty",
      "crusher auxiliary drives"
    ],
    "failure_modes": [
      "fine dust or moisture bypassing a worn 2RS1 lip in dirty or wet duty",
      "shield rubbing after misalignment or overheating of a 2Z execution",
      "grease escape past the non-contact shields in an overfilled or vertically mounted position",
      "tilted mounting that loads one double row more heavily than the other",
      "brinelling from pressing the ring home through the balls or from static overload",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Fit and fillet rules are unchanged from the open double-row 3315: k5 on a 75 mm rotating shaft, radii clearing the chamfer.",
      "The capped speed ceiling is 4,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "The capped speed ceiling is 4,000 r/min — seal drag and grease life govern, which is why SKF publishes no thermal reference speed for A-2Z.",
      "Fit and fillet rules are unchanged from the open double-row 3315: k5 on a 75 mm rotating shaft, radii clearing the chamfer.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for 3315 A-2Z as the double shielded execution; the other order numbers of the 3315 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of 3315-A-2Z?",
        "a": "3315 A-2Z measures 75 mm bore × 160 mm OD × 68.3 mm width (2.953 × 6.299 × 2.689 in), mass about 5600 g. SKF 17000 ratings: C 176 kN, C0 140 kN, Pu 5.5 kN, SKF publishes only the 4,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the A-2Z suffix mean?",
        "a": "A on this double-row bearing means no filling slots, so both ball rows retain their full complement. -2Z marks a sheet-metal shield on each side: non-contacting, grease-retention and dust protection with negligible drag, the bearing remaining open-style relubricatable only through the shield clearance."
      },
      {
        "q": "What loads can 3315-A-2Z take?",
        "a": "The same bidirectional combined loads as the open double-row 3315: C 176 kN, C0 140 kN, Pu 5.5 kN. Capping changes sealing and speed, not the basic ratings."
      },
      {
        "q": "Is 3315-A-2Z sealed for life?",
        "a": "It is shielded on both sides (-2Z) and delivered filled with the appropriate SKF grease; the non-contact shields give low-drag grease retention and dust protection, but the arrangement is not a contact-sealed cavity."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "3315-A",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×68.3 mm envelope with catalogue ratings within 10 %; 3315 A is the stamped steel cage, open arrangement execution of this size — boundary dimensions interchangeable, execution differs."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "3315-A-2Z",
      "3315 A-2Z"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-202-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 202 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 15,
    "D_mm": 35,
    "B_mm": 11,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 12.7,
    "static_load_kN": 8.3,
    "fatigue_load_limit_kN": 0.355,
    "limiting_speed_rpm": 36000,
    "max_rpm": 36000,
    "weight_g": 62,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 202 N2MA is SKF's 15 mm-bore QJ four-point contact ball bearing of the QJ200 series, 15×35×11 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 15×35×11 mm (0.591×1.378×0.433 in), 10.0 mm radial section height, C 12.7 kN, C0 8.3 kN, Pu 0.355 kN.SKF publishes only the 36,000 r/min limiting speed for this execution, catalogue mass 62 g. Sizing arithmetic on the 15 mm bore: 12.7 kN C divided by the 10.0 mm radial section height gives 1.3 kN per section millimetre; the 62 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 11 mm width over a 10.0 mm section yields 1.10 mm of ring width per section millimetre, and the bearing weighs 62 g for 12.7 kN of dynamic capacity — about 5 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 36,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "compact thrust-carrying positions paired with a deep-groove radial bearing",
      "gear selector and indexing mechanisms",
      "small screw and cam drives"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-202-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-202-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 202 N2MA as the qj slotted execution; the other order numbers of the QJ 202 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-202-N2MA?",
        "a": "QJ 202 N2MA measures 15 mm bore × 35 mm OD × 11 mm width (0.591 × 1.378 × 0.433 in), mass about 62 g. SKF 17000 ratings: C 12.7 kN, C0 8.3 kN, Pu 0.355 kN, SKF publishes only the 36,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 202 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7202-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (12.7/8.3 kN vs 8.32/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (12.7/8.3 kN vs 8.32/4.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (12.7/8.3 kN vs 8.8/4.65 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 15×35×11 mm envelope, but catalogue C/C0 differ between executions (12.7/8.3 kN vs 10.2/5.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7202",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7202 BEP shares the 15×35×11 mm angular-contact envelope, but catalogue C/C0 differ (12.7/8.3 kN vs 8.32/4.4 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-202-N2MA",
      "QJ 202 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-203-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 203 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 40,
    "B_mm": 12,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 17,
    "static_load_kN": 11.4,
    "fatigue_load_limit_kN": 0.48,
    "limiting_speed_rpm": 30000,
    "max_rpm": 30000,
    "weight_g": 82,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 203 N2MA is SKF's 17 mm-bore QJ four-point contact ball bearing of the QJ200 series, 17×40×12 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 17×40×12 mm (0.669×1.575×0.472 in), 11.5 mm radial section height, C 17 kN, C0 11.4 kN, Pu 0.48 kN.SKF publishes only the 30,000 r/min limiting speed for this execution, catalogue mass 82 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 30,000 r/min and no separate thermal reference is published; at dm ≈ 28.5 mm the corresponding dn is approximately 855k mm·r/min. At the printed limiting speed of 30,000 r/min the mean pitch diameter dm ≈ 28.5 mm implies a dn value around 855k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 30,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gear selector and indexing mechanisms",
      "small screw and cam drives",
      "compact thrust-carrying positions paired with a deep-groove radial bearing"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is built into QJ-203-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-203-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 203 N2MA as the qj slotted execution; the other order numbers of the QJ 203 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-203-N2MA?",
        "a": "QJ 203 N2MA measures 17 mm bore × 40 mm OD × 12 mm width (0.669 × 1.575 × 0.472 in), mass about 82 g. SKF 17000 ratings: C 17 kN, C0 11.4 kN, Pu 0.48 kN, SKF publishes only the 30,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-203-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7203-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (17/11.4 kN vs 10.4/5.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (17/11.4 kN vs 10.4/5.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (17/11.4 kN vs 11/5.85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (17/11.4 kN vs 11/5.85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (17/11.4 kN vs 11.1/6.1 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×40×12 mm envelope, but catalogue C/C0 differ between executions (17/11.4 kN vs 12.5/6.7 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7203",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7203 BEP shares the 17×40×12 mm angular-contact envelope, but catalogue C/C0 differ (17/11.4 kN vs 10.4/5.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-203-N2MA",
      "QJ 203 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-303-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 303 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 17,
    "D_mm": 47,
    "B_mm": 14,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 23.4,
    "static_load_kN": 15,
    "fatigue_load_limit_kN": 0.64,
    "limiting_speed_rpm": 28000,
    "max_rpm": 28000,
    "weight_g": 140,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 303 N2MA is SKF's 17 mm-bore QJ four-point contact ball bearing of the QJ300 series, 17×47×14 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 17×47×14 mm (0.669×1.85×0.551 in), 15.0 mm radial section height, C 23.4 kN, C0 15 kN, Pu 0.64 kN.SKF publishes only the 28,000 r/min limiting speed for this execution, catalogue mass 140 g. Sizing arithmetic on the 17 mm bore: 23.4 kN C divided by the 15.0 mm radial section height gives 1.6 kN per section millimetre; the 140 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 14 mm width over a 15.0 mm section yields 0.93 mm of ring width per section millimetre, and the bearing weighs 140 g for 23.4 kN of dynamic capacity — about 6 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 28,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gear selector and indexing mechanisms",
      "small screw and cam drives",
      "compact thrust-carrying positions paired with a deep-groove radial bearing"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-303-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-303-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 303 N2MA as the qj slotted execution; the other order numbers of the QJ 303 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-303-N2MA?",
        "a": "QJ 303 N2MA measures 17 mm bore × 47 mm OD × 14 mm width (0.669 × 1.85 × 0.551 in), mass about 140 g. SKF 17000 ratings: C 23.4 kN, C0 15 kN, Pu 0.64 kN, SKF publishes only the 28,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 303 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7303-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope, but catalogue C/C0 differ between executions (23.4/15 kN vs 15.9/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7303-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope, but catalogue C/C0 differ between executions (23.4/15 kN vs 15.9/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7303-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 17×47×14 mm envelope, but catalogue C/C0 differ between executions (23.4/15 kN vs 15.9/8.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7303",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7303 BEP shares the 17×47×14 mm angular-contact envelope, but catalogue C/C0 differ (23.4/15 kN vs 15.9/8.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-303-N2MA",
      "QJ 303 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-304-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 304 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 32,
    "static_load_kN": 21.6,
    "fatigue_load_limit_kN": 0.93,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 304 N2MA is SKF's 20 mm-bore QJ four-point contact ball bearing of the QJ300 series, 20×52×15 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 32 kN, C0 21.6 kN, Pu 0.93 kN.SKF publishes only the 24,000 r/min limiting speed for this execution, catalogue mass 180 g. Selection figures for QJ 304 N2MA: the static-to-dynamic ratio C0/C is 0.68, Pu 0.93 kN is about 3 % of C, and catalogue mass works out to roughly 9 g per millimetre of bore. Envelope economics: the 15 mm width over a 16.0 mm section yields 0.94 mm of ring width per section millimetre, and the bearing weighs 180 g for 32 kN of dynamic capacity — about 6 g per rated kN. Bore-to-OD planning: OD 52 over bore 20 is a 2.60× step for this size, and the 15 mm width gives a bore/width ratio of 1.33; use these ratios when housing space around the 20 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "compact thrust-carrying positions paired with a deep-groove radial bearing",
      "gear selector and indexing mechanisms",
      "small screw and cam drives"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-304-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-304-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 304 N2MA as the qj slotted execution; the other order numbers of the QJ 304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-304-N2MA?",
        "a": "QJ 304 N2MA measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 180 g. SKF 17000 ratings: C 32 kN, C0 21.6 kN, Pu 0.93 kN, SKF publishes only the 24,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 304 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; QJ 304 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; QJ 304 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7304 BEP shares the 20×52×15 mm angular-contact envelope, but catalogue C/C0 differ (32/21.6 kN vs 17.4/9.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-304-N2MA",
      "QJ 304 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-304-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 304 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 32,
    "static_load_kN": 21.6,
    "fatigue_load_limit_kN": 0.93,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 304 MA is SKF's 20 mm-bore QJ four-point contact ball bearing of the QJ300 series, 20×52×15 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 32 kN, C0 21.6 kN, Pu 0.93 kN.SKF publishes only the 24,000 r/min limiting speed for this execution, catalogue mass 180 g. Sizing arithmetic on the 20 mm bore: 32 kN C divided by the 16.0 mm radial section height gives 2.0 kN per section millimetre; the 180 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. The 0.93 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 32/21.6 kN ratings and 180 g mass this execution carries about 1.60 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 24,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "small screw and cam drives",
      "compact thrust-carrying positions paired with a deep-groove radial bearing",
      "gear selector and indexing mechanisms"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is NOT built into QJ-304-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-304-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 304 MA as the qj plain execution; the other order numbers of the QJ 304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-304-MA?",
        "a": "QJ 304 MA measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 180 g. SKF 17000 ratings: C 32 kN, C0 21.6 kN, Pu 0.93 kN, SKF publishes only the 24,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 304 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; QJ 304 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-304-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; QJ 304 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7304 BEP shares the 20×52×15 mm angular-contact envelope, but catalogue C/C0 differ (32/21.6 kN vs 17.4/9.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-304-MA",
      "QJ 304 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-304-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 304 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 20,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 32,
    "static_load_kN": 21.6,
    "fatigue_load_limit_kN": 0.93,
    "limiting_speed_rpm": 24000,
    "max_rpm": 24000,
    "weight_g": 180,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 304 N2PHAS is SKF's 20 mm-bore QJ four-point contact ball bearing of the QJ300 series, 20×52×15 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 20×52×15 mm (0.787×2.047×0.591 in), 16.0 mm radial section height, C 32 kN, C0 21.6 kN, Pu 0.93 kN.SKF publishes only the 24,000 r/min limiting speed for this execution, catalogue mass 180 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 24,000 r/min and no separate thermal reference is published; at dm ≈ 36.0 mm the corresponding dn is approximately 864k mm·r/min. Sizing arithmetic on the 20 mm bore: 32 kN C divided by the 16.0 mm radial section height gives 2.0 kN per section millimetre; the 180 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 24,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "small screw and cam drives",
      "compact thrust-carrying positions paired with a deep-groove radial bearing",
      "gear selector and indexing mechanisms"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-304-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-304-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 304 N2PHAS as the qj slotted execution; the other order numbers of the QJ 304 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-304-N2PHAS?",
        "a": "QJ 304 N2PHAS measures 20 mm bore × 52 mm OD × 15 mm width (0.787 × 2.047 × 0.591 in), mass about 180 g. SKF 17000 ratings: C 32 kN, C0 21.6 kN, Pu 0.93 kN, SKF publishes only the 24,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What minimum axial load does QJ-304-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7304-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 17.4/9.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 19/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 20.4/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7304-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 20×52×15 mm envelope, but catalogue C/C0 differ between executions (32/21.6 kN vs 20.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-304-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; QJ 304 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-304-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 20×52×15 mm envelope with catalogue ratings within 10 %; QJ 304 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7304",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7304 BEP shares the 20×52×15 mm angular-contact envelope, but catalogue C/C0 differ (32/21.6 kN vs 17.4/9.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-304-N2PHAS",
      "QJ 304 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-205-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 205 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 52,
    "B_mm": 15,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 27,
    "static_load_kN": 21.2,
    "fatigue_load_limit_kN": 0.9,
    "limiting_speed_rpm": 22000,
    "max_rpm": 22000,
    "weight_g": 160,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 205 N2MA is SKF's 25 mm-bore QJ four-point contact ball bearing of the QJ200 series, 25×52×15 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 25×52×15 mm (0.984×2.047×0.591 in), 13.5 mm radial section height, C 27 kN, C0 21.2 kN, Pu 0.9 kN.SKF publishes only the 22,000 r/min limiting speed for this execution, catalogue mass 160 g. Selection figures for QJ 205 N2MA: the static-to-dynamic ratio C0/C is 0.79, Pu 0.9 kN is about 3 % of C, and catalogue mass works out to roughly 6 g per millimetre of bore. Envelope economics: the 15 mm width over a 13.5 mm section yields 1.11 mm of ring width per section millimetre, and the bearing weighs 160 g for 27 kN of dynamic capacity — about 6 g per rated kN. Bore-to-OD planning: OD 52 over bore 25 is a 2.08× step for this size, and the 15 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 25 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-205-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-205-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 205 N2MA as the qj slotted execution; the other order numbers of the QJ 205 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-205-N2MA?",
        "a": "QJ 205 N2MA measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 160 g. SKF 17000 ratings: C 27 kN, C0 21.2 kN, Pu 0.9 kN, SKF publishes only the 22,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 205 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7205-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 14.8/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 14.8/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 14.8/9.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 15.6/10 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×52×15 mm envelope, but catalogue C/C0 differ between executions (27/21.2 kN vs 18/11.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7205",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7205 BEP shares the 25×52×15 mm angular-contact envelope, but catalogue C/C0 differ (27/21.2 kN vs 14.8/9.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-205-N2MA",
      "QJ 205 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-305-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 305 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 42.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 305 N2MA is SKF's 25 mm-bore QJ four-point contact ball bearing of the QJ300 series, 25×62×17 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 42.5 kN, C0 30 kN, Pu 1.27 kN.SKF publishes only the 20,000 r/min limiting speed for this execution, catalogue mass 290 g. Load balance: C0 30 kN against C 42.5 kN gives a 0.71 ratio, typical of a four-point thrust-oriented design; Pu 1.27 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 20,000 r/min and no separate thermal reference is published; at dm ≈ 43.5 mm the corresponding dn is approximately 870k mm·r/min. Bore-to-OD planning: OD 62 over bore 25 is a 2.48× step for this size, and the 17 mm width gives a bore/width ratio of 1.47; use these ratios when housing space around the 25 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-305-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-305-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 305 N2MA as the qj slotted execution; the other order numbers of the QJ 305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-305-N2MA?",
        "a": "QJ 305 N2MA measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 290 g. SKF 17000 ratings: C 42.5 kN, C0 30 kN, Pu 1.27 kN, SKF publishes only the 20,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-305-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; QJ 305 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7305 BEP shares the 25×62×17 mm angular-contact envelope, but catalogue C/C0 differ (42.5/30 kN vs 24.2/14 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-305-N2MA",
      "QJ 305 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-305-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 305 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 25,
    "D_mm": 62,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 42.5,
    "static_load_kN": 30,
    "fatigue_load_limit_kN": 1.27,
    "limiting_speed_rpm": 20000,
    "max_rpm": 20000,
    "weight_g": 290,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 305 MA is SKF's 25 mm-bore QJ four-point contact ball bearing of the QJ300 series, 25×62×17 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 25×62×17 mm (0.984×2.441×0.669 in), 18.5 mm radial section height, C 42.5 kN, C0 30 kN, Pu 1.27 kN.SKF publishes only the 20,000 r/min limiting speed for this execution, catalogue mass 290 g. At the printed limiting speed of 20,000 r/min the mean pitch diameter dm ≈ 43.5 mm implies a dn value around 870k mm·r/min; only the limiting speed is published for this execution. The 1.27 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 42.5/30 kN ratings and 290 g mass this execution carries about 1.70 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 20,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "screw and worm drives",
      "pump thrust positions",
      "clutch and brake assemblies"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is NOT built into QJ-305-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-305-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 305 MA as the qj plain execution; the other order numbers of the QJ 305 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-305-MA?",
        "a": "QJ 305 MA measures 25 mm bore × 62 mm OD × 17 mm width (0.984 × 2.441 × 0.669 in), mass about 290 g. SKF 17000 ratings: C 42.5 kN, C0 30 kN, Pu 1.27 kN, SKF publishes only the 20,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-305-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7305-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 24.2/14 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 26.5/15.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7305-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 25×62×17 mm envelope, but catalogue C/C0 differ between executions (42.5/30 kN vs 29/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-305-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 25×62×17 mm envelope with catalogue ratings within 10 %; QJ 305 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7305",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7305 BEP shares the 25×62×17 mm angular-contact envelope, but catalogue C/C0 differ (42.5/30 kN vs 24.2/14 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-305-MA",
      "QJ 305 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-206-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 206 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 37.5,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 1.29,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 240,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 206 N2MA is SKF's 30 mm-bore QJ four-point contact ball bearing of the QJ200 series, 30×62×16 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 37.5 kN, C0 30.5 kN, Pu 1.29 kN.SKF publishes only the 19,000 r/min limiting speed for this execution, catalogue mass 240 g. The 1.29 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 37.5/30.5 kN ratings and 240 g mass this execution carries about 1.25 kN of C per millimetre of bore. Selection figures for QJ 206 N2MA: the static-to-dynamic ratio C0/C is 0.81, Pu 1.29 kN is about 3 % of C, and catalogue mass works out to roughly 8 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 19,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-206-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-206-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 206 N2MA as the qj slotted execution; the other order numbers of the QJ 206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-206-N2MA?",
        "a": "QJ 206 N2MA measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 240 g. SKF 17000 ratings: C 37.5 kN, C0 30.5 kN, Pu 1.29 kN, SKF publishes only the 19,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 206 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 25.5/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; QJ 206 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7206 BEP shares the 30×62×16 mm angular-contact envelope, but catalogue C/C0 differ (37.5/30.5 kN vs 22.5/14.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-206-N2MA",
      "QJ 206 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-206-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 206 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 62,
    "B_mm": 16,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 37.5,
    "static_load_kN": 30.5,
    "fatigue_load_limit_kN": 1.29,
    "limiting_speed_rpm": 19000,
    "max_rpm": 19000,
    "weight_g": 240,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 206 MA is SKF's 30 mm-bore QJ four-point contact ball bearing of the QJ200 series, 30×62×16 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 30×62×16 mm (1.181×2.441×0.63 in), 16.0 mm radial section height, C 37.5 kN, C0 30.5 kN, Pu 1.29 kN.SKF publishes only the 19,000 r/min limiting speed for this execution, catalogue mass 240 g. Selection figures for QJ 206 MA: the static-to-dynamic ratio C0/C is 0.81, Pu 1.29 kN is about 3 % of C, and catalogue mass works out to roughly 8 g per millimetre of bore. Load balance: C0 30.5 kN against C 37.5 kN gives a 0.81 ratio, typical of a four-point thrust-oriented design; Pu 1.29 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 62 over bore 30 is a 2.07× step for this size, and the 16 mm width gives a bore/width ratio of 1.88; use these ratios when housing space around the 30 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is NOT built into QJ-206-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-206-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 206 MA as the qj plain execution; the other order numbers of the QJ 206 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-206-MA?",
        "a": "QJ 206 MA measures 30 mm bore × 62 mm OD × 16 mm width (1.181 × 2.441 × 0.63 in), mass about 240 g. SKF 17000 ratings: C 37.5 kN, C0 30.5 kN, Pu 1.29 kN, SKF publishes only the 19,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 206 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7206-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 22.5/14.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 24/15.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 25.5/17 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7206-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×62×16 mm envelope, but catalogue C/C0 differ between executions (37.5/30.5 kN vs 27.5/17.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-206-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×62×16 mm envelope with catalogue ratings within 10 %; QJ 206 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7206",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7206 BEP shares the 30×62×16 mm angular-contact envelope, but catalogue C/C0 differ (37.5/30.5 kN vs 22.5/14.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-206-MA",
      "QJ 206 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-306-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 306 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 53,
    "static_load_kN": 41.5,
    "fatigue_load_limit_kN": 1.76,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 306 N2MA is SKF's 30 mm-bore QJ four-point contact ball bearing of the QJ300 series, 30×72×19 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 53 kN, C0 41.5 kN, Pu 1.76 kN.SKF publishes only the 17,000 r/min limiting speed for this execution, catalogue mass 420 g. At the printed limiting speed of 17,000 r/min the mean pitch diameter dm ≈ 51.0 mm implies a dn value around 867k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 17,000 r/min and no separate thermal reference is published; at dm ≈ 51.0 mm the corresponding dn is approximately 867k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 17,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-306-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-306-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 306 N2MA as the qj slotted execution; the other order numbers of the QJ 306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-306-N2MA?",
        "a": "QJ 306 N2MA measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 53 kN, C0 41.5 kN, Pu 1.76 kN, SKF publishes only the 17,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-306-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 37.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; QJ 306 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; QJ 306 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7306 BEP shares the 30×72×19 mm angular-contact envelope, but catalogue C/C0 differ (53/41.5 kN vs 32.5/19.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-306-N2MA",
      "QJ 306 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-306-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 306 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 53,
    "static_load_kN": 41.5,
    "fatigue_load_limit_kN": 1.76,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 306 MA is SKF's 30 mm-bore QJ four-point contact ball bearing of the QJ300 series, 30×72×19 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 53 kN, C0 41.5 kN, Pu 1.76 kN.SKF publishes only the 17,000 r/min limiting speed for this execution, catalogue mass 420 g. Mass and section check: 420 g inside the 30×72×19 mm outline leaves a 21.0 mm radial section, and the 41.5 kN static rating is 0.78× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 41.5 kN against C 53 kN gives a 0.78 ratio, typical of a four-point thrust-oriented design; Pu 1.76 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 72 over bore 30 is a 2.40× step for this size, and the 19 mm width gives a bore/width ratio of 1.58; use these ratios when housing space around the 30 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "pump thrust positions",
      "clutch and brake assemblies",
      "textile machinery traverse drives"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is NOT built into QJ-306-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-306-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 306 MA as the qj plain execution; the other order numbers of the QJ 306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-306-MA?",
        "a": "QJ 306 MA measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 53 kN, C0 41.5 kN, Pu 1.76 kN, SKF publishes only the 17,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-306-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 37.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; QJ 306 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-306-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; QJ 306 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7306 BEP shares the 30×72×19 mm angular-contact envelope, but catalogue C/C0 differ (53/41.5 kN vs 32.5/19.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-306-MA",
      "QJ 306 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-306-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 306 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 30,
    "D_mm": 72,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 53,
    "static_load_kN": 41.5,
    "fatigue_load_limit_kN": 1.76,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 420,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 306 N2PHAS is SKF's 30 mm-bore QJ four-point contact ball bearing of the QJ300 series, 30×72×19 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 30×72×19 mm (1.181×2.835×0.748 in), 21.0 mm radial section height, C 53 kN, C0 41.5 kN, Pu 1.76 kN.SKF publishes only the 17,000 r/min limiting speed for this execution, catalogue mass 420 g. Envelope economics: the 19 mm width over a 21.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 420 g for 53 kN of dynamic capacity — about 8 g per rated kN. Mass and section check: 420 g inside the 30×72×19 mm outline leaves a 21.0 mm radial section, and the 41.5 kN static rating is 0.78× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 72 over bore 30 is a 2.40× step for this size, and the 19 mm width gives a bore/width ratio of 1.58; use these ratios when housing space around the 30 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-306-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-306-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 306 N2PHAS as the qj slotted execution; the other order numbers of the QJ 306 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-306-N2PHAS?",
        "a": "QJ 306 N2PHAS measures 30 mm bore × 72 mm OD × 19 mm width (1.181 × 2.835 × 0.748 in), mass about 420 g. SKF 17000 ratings: C 53 kN, C0 41.5 kN, Pu 1.76 kN, SKF publishes only the 17,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What does QJ mean in QJ 306 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7306-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 32.5/19.3 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 35.5/21.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 37.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7306-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 30×72×19 mm envelope, but catalogue C/C0 differ between executions (53/41.5 kN vs 39/23.6 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-306-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; QJ 306 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-306-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 30×72×19 mm envelope with catalogue ratings within 10 %; QJ 306 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7306",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7306 BEP shares the 30×72×19 mm angular-contact envelope, but catalogue C/C0 differ (53/41.5 kN vs 32.5/19.3 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-306-N2PHAS",
      "QJ 306 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-207-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 207 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 72,
    "B_mm": 17,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 49,
    "static_load_kN": 41.5,
    "fatigue_load_limit_kN": 1.76,
    "limiting_speed_rpm": 17000,
    "max_rpm": 17000,
    "weight_g": 350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 207 N2MA is SKF's 35 mm-bore QJ four-point contact ball bearing of the QJ200 series, 35×72×17 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 35×72×17 mm (1.378×2.835×0.669 in), 18.5 mm radial section height, C 49 kN, C0 41.5 kN, Pu 1.76 kN.SKF publishes only the 17,000 r/min limiting speed for this execution, catalogue mass 350 g. At the printed limiting speed of 17,000 r/min the mean pitch diameter dm ≈ 53.5 mm implies a dn value around 910k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 17,000 r/min and no separate thermal reference is published; at dm ≈ 53.5 mm the corresponding dn is approximately 910k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 17,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-207-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-207-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 207 N2MA as the qj slotted execution; the other order numbers of the QJ 207 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-207-N2MA?",
        "a": "QJ 207 N2MA measures 35 mm bore × 72 mm OD × 17 mm width (1.378 × 2.835 × 0.669 in), mass about 350 g. SKF 17000 ratings: C 49 kN, C0 41.5 kN, Pu 1.76 kN, SKF publishes only the 17,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-207-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7207-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (49/41.5 kN vs 29.1/19 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (49/41.5 kN vs 29.1/19 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (49/41.5 kN vs 31/20.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (49/41.5 kN vs 31/20.8 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (49/41.5 kN vs 32.5/22.4 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×72×17 mm envelope, but catalogue C/C0 differ between executions (49/41.5 kN vs 35.5/23.2 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7207",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7207 BEP shares the 35×72×17 mm angular-contact envelope, but catalogue C/C0 differ (49/41.5 kN vs 29.1/19 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-207-N2MA",
      "QJ 207 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-307-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 307 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 64,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 307 N2MA is SKF's 35 mm-bore QJ four-point contact ball bearing of the QJ300 series, 35×80×21 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 64 kN, C0 51 kN, Pu 2.16 kN.SKF publishes only the 15,000 r/min limiting speed for this execution, catalogue mass 570 g. The 2.16 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 64/51 kN ratings and 570 g mass this execution carries about 1.83 kN of C per millimetre of bore. Selection figures for QJ 307 N2MA: the static-to-dynamic ratio C0/C is 0.80, Pu 2.16 kN is about 3 % of C, and catalogue mass works out to roughly 16 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 15,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw and worm drives",
      "pump thrust positions",
      "clutch and brake assemblies"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-307-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-307-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 307 N2MA as the qj slotted execution; the other order numbers of the QJ 307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-307-N2MA?",
        "a": "QJ 307 N2MA measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 570 g. SKF 17000 ratings: C 64 kN, C0 51 kN, Pu 2.16 kN, SKF publishes only the 15,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 307 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; QJ 307 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; QJ 307 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7307 BEP shares the 35×80×21 mm angular-contact envelope, but catalogue C/C0 differ (64/51 kN vs 39/24.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-307-N2MA",
      "QJ 307 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-307-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 307 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 64,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 307 MA is SKF's 35 mm-bore QJ four-point contact ball bearing of the QJ300 series, 35×80×21 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 64 kN, C0 51 kN, Pu 2.16 kN.SKF publishes only the 15,000 r/min limiting speed for this execution, catalogue mass 570 g. Selection figures for QJ 307 MA: the static-to-dynamic ratio C0/C is 0.80, Pu 2.16 kN is about 3 % of C, and catalogue mass works out to roughly 16 g per millimetre of bore. Load balance: C0 51 kN against C 64 kN gives a 0.80 ratio, typical of a four-point thrust-oriented design; Pu 2.16 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 21 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 35 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is NOT built into QJ-307-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-307-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 307 MA as the qj plain execution; the other order numbers of the QJ 307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-307-MA?",
        "a": "QJ 307 MA measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 570 g. SKF 17000 ratings: C 64 kN, C0 51 kN, Pu 2.16 kN, SKF publishes only the 15,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 307 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; QJ 307 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-307-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; QJ 307 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7307 BEP shares the 35×80×21 mm angular-contact envelope, but catalogue C/C0 differ (64/51 kN vs 39/24.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-307-MA",
      "QJ 307 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-307-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 307 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 35,
    "D_mm": 80,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 64,
    "static_load_kN": 51,
    "fatigue_load_limit_kN": 2.16,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 570,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 307 N2PHAS is SKF's 35 mm-bore QJ four-point contact ball bearing of the QJ300 series, 35×80×21 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 64 kN, C0 51 kN, Pu 2.16 kN.SKF publishes only the 15,000 r/min limiting speed for this execution, catalogue mass 570 g. Load balance: C0 51 kN against C 64 kN gives a 0.80 ratio, typical of a four-point thrust-oriented design; Pu 2.16 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 570 g inside the 35×80×21 mm outline leaves a 22.5 mm radial section, and the 51 kN static rating is 0.80× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 80 over bore 35 is a 2.29× step for this size, and the 21 mm width gives a bore/width ratio of 1.67; use these ratios when housing space around the 35 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-307-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-307-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 307 N2PHAS as the qj slotted execution; the other order numbers of the QJ 307 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-307-N2PHAS?",
        "a": "QJ 307 N2PHAS measures 35 mm bore × 80 mm OD × 21 mm width (1.378 × 3.15 × 0.827 in), mass about 570 g. SKF 17000 ratings: C 64 kN, C0 51 kN, Pu 2.16 kN, SKF publishes only the 15,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-307-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7307-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 39/24.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 41.5/26.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7307-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 35×80×21 mm envelope, but catalogue C/C0 differ between executions (64/51 kN vs 46.5/30 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-307-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; QJ 307 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-307-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 35×80×21 mm envelope with catalogue ratings within 10 %; QJ 307 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7307",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7307 BEP shares the 35×80×21 mm angular-contact envelope, but catalogue C/C0 differ (64/51 kN vs 39/24.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-307-N2PHAS",
      "QJ 307 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-208-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 208 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 80,
    "B_mm": 18,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 56,
    "static_load_kN": 49,
    "fatigue_load_limit_kN": 2.08,
    "limiting_speed_rpm": 15000,
    "max_rpm": 15000,
    "weight_g": 450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 208 MA is SKF's 40 mm-bore QJ four-point contact ball bearing of the QJ200 series, 40×80×18 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 40×80×18 mm (1.575×3.15×0.709 in), 20.0 mm radial section height, C 56 kN, C0 49 kN, Pu 2.08 kN.SKF publishes only the 15,000 r/min limiting speed for this execution, catalogue mass 450 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 15,000 r/min and no separate thermal reference is published; at dm ≈ 60.0 mm the corresponding dn is approximately 900k mm·r/min. Sizing arithmetic on the 40 mm bore: 56 kN C divided by the 20.0 mm radial section height gives 2.8 kN per section millimetre; the 450 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 15,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is NOT built into QJ-208-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-208-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 208 MA as the qj plain execution; the other order numbers of the QJ 208 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-208-MA?",
        "a": "QJ 208 MA measures 40 mm bore × 80 mm OD × 18 mm width (1.575 × 3.15 × 0.709 in), mass about 450 g. SKF 17000 ratings: C 56 kN, C0 49 kN, Pu 2.08 kN, SKF publishes only the 15,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-208-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7208-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 34.5/24 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 34.5/24 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 36.5/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 36.5/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 36.5/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 39/28 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×80×18 mm envelope, but catalogue C/C0 differ between executions (56/49 kN vs 41.5/29 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7208",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7208 BEP shares the 40×80×18 mm angular-contact envelope, but catalogue C/C0 differ (56/49 kN vs 34.5/24 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-208-MA",
      "QJ 208 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-308-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 308 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 78,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.7,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 308 N2MA is SKF's 40 mm-bore QJ four-point contact ball bearing of the QJ300 series, 40×90×23 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 78 kN, C0 64 kN, Pu 2.7 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 780 g. Envelope economics: the 23 mm width over a 25.0 mm section yields 0.92 mm of ring width per section millimetre, and the bearing weighs 780 g for 78 kN of dynamic capacity — about 10 g per rated kN. Selection figures for QJ 308 N2MA: the static-to-dynamic ratio C0/C is 0.82, Pu 2.7 kN is about 3 % of C, and catalogue mass works out to roughly 20 g per millimetre of bore. Bore-to-OD planning: OD 90 over bore 40 is a 2.25× step for this size, and the 23 mm width gives a bore/width ratio of 1.74; use these ratios when housing space around the 40 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-308-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-308-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 308 N2MA as the qj slotted execution; the other order numbers of the QJ 308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-308-N2MA?",
        "a": "QJ 308 N2MA measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 780 g. SKF 17000 ratings: C 78 kN, C0 64 kN, Pu 2.7 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 308 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 53/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; QJ 308 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; QJ 308 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7308 BEP shares the 40×90×23 mm angular-contact envelope, but catalogue C/C0 differ (78/64 kN vs 46.2/30.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-308-N2MA",
      "QJ 308 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-308-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 308 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 78,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.7,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 308 MA is SKF's 40 mm-bore QJ four-point contact ball bearing of the QJ300 series, 40×90×23 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 78 kN, C0 64 kN, Pu 2.7 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 780 g. The 2.7 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 78/64 kN ratings and 780 g mass this execution carries about 1.95 kN of C per millimetre of bore. Sizing arithmetic on the 40 mm bore: 78 kN C divided by the 25.0 mm radial section height gives 3.1 kN per section millimetre; the 780 g mass and 3 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 14,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is NOT built into QJ-308-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-308-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 308 MA as the qj plain execution; the other order numbers of the QJ 308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-308-MA?",
        "a": "QJ 308 MA measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 780 g. SKF 17000 ratings: C 78 kN, C0 64 kN, Pu 2.7 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 308 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 53/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; QJ 308 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-308-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; QJ 308 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7308 BEP shares the 40×90×23 mm angular-contact envelope, but catalogue C/C0 differ (78/64 kN vs 46.2/30.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-308-MA",
      "QJ 308 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-308-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 308 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 40,
    "D_mm": 90,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 78,
    "static_load_kN": 64,
    "fatigue_load_limit_kN": 2.7,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 780,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 308 N2PHAS is SKF's 40 mm-bore QJ four-point contact ball bearing of the QJ300 series, 40×90×23 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 40×90×23 mm (1.575×3.543×0.906 in), 25.0 mm radial section height, C 78 kN, C0 64 kN, Pu 2.7 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 780 g. At the printed limiting speed of 14,000 r/min the mean pitch diameter dm ≈ 65.0 mm implies a dn value around 910k mm·r/min; only the limiting speed is published for this execution. The 2.7 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 78/64 kN ratings and 780 g mass this execution carries about 1.95 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 14,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-308-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-308-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 308 N2PHAS as the qj slotted execution; the other order numbers of the QJ 308 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-308-N2PHAS?",
        "a": "QJ 308 N2PHAS measures 40 mm bore × 90 mm OD × 23 mm width (1.575 × 3.543 × 0.906 in), mass about 780 g. SKF 17000 ratings: C 78 kN, C0 64 kN, Pu 2.7 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What minimum axial load does QJ-308-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7308-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 46.2/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 50/32.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 53/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7308-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 40×90×23 mm envelope, but catalogue C/C0 differ between executions (78/64 kN vs 56/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-308-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; QJ 308 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-308-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 40×90×23 mm envelope with catalogue ratings within 10 %; QJ 308 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7308",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7308 BEP shares the 40×90×23 mm angular-contact envelope, but catalogue C/C0 differ (78/64 kN vs 46.2/30.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-308-N2PHAS",
      "QJ 308 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-209-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 209 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 85,
    "B_mm": 19,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 63,
    "static_load_kN": 56,
    "fatigue_load_limit_kN": 2.36,
    "limiting_speed_rpm": 14000,
    "max_rpm": 14000,
    "weight_g": 520,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 209 MA is SKF's 45 mm-bore QJ four-point contact ball bearing of the QJ200 series, 45×85×19 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 45×85×19 mm (1.772×3.346×0.748 in), 20.0 mm radial section height, C 63 kN, C0 56 kN, Pu 2.36 kN.SKF publishes only the 14,000 r/min limiting speed for this execution, catalogue mass 520 g. The 2.36 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 63/56 kN ratings and 520 g mass this execution carries about 1.40 kN of C per millimetre of bore. Sizing arithmetic on the 45 mm bore: 63 kN C divided by the 20.0 mm radial section height gives 3.1 kN per section millimetre; the 520 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 14,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is NOT built into QJ-209-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-209-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 209 MA as the qj plain execution; the other order numbers of the QJ 209 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-209-MA?",
        "a": "QJ 209 MA measures 45 mm bore × 85 mm OD × 19 mm width (1.772 × 3.346 × 0.748 in), mass about 520 g. SKF 17000 ratings: C 63 kN, C0 56 kN, Pu 2.36 kN, SKF publishes only the 14,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 209 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7209-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (63/56 kN vs 35.8/26 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (63/56 kN vs 38/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (63/56 kN vs 38/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (63/56 kN vs 38/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (63/56 kN vs 40/30.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×85×19 mm envelope, but catalogue C/C0 differ between executions (63/56 kN vs 44/32 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7209",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7209 BECBP shares the 45×85×19 mm angular-contact envelope, but catalogue C/C0 differ (63/56 kN vs 38/28.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-209-MA",
      "QJ 209 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-309-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 309 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 100,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 309 N2MA is SKF's 45 mm-bore QJ four-point contact ball bearing of the QJ300 series, 45×100×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 100 kN, C0 83 kN, Pu 3.55 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 1050 g. Mass and section check: 1050 g inside the 45×100×25 mm outline leaves a 27.5 mm radial section, and the 83 kN static rating is 0.83× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 12,000 r/min the mean pitch diameter dm ≈ 72.5 mm implies a dn value around 870k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "pump thrust positions",
      "clutch and brake assemblies",
      "textile machinery traverse drives"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is built into QJ-309-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-309-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 309 N2MA as the qj slotted execution; the other order numbers of the QJ 309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-309-N2MA?",
        "a": "QJ 309 N2MA measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 1050 g. SKF 17000 ratings: C 100 kN, C0 83 kN, Pu 3.55 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-309-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7309 BEP shares the 45×100×25 mm angular-contact envelope, but catalogue C/C0 differ (100/83 kN vs 55.9/37.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-309-N2MA",
      "QJ 309 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-309-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 309 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 100,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 309 MA is SKF's 45 mm-bore QJ four-point contact ball bearing of the QJ300 series, 45×100×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 100 kN, C0 83 kN, Pu 3.55 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 1050 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 12,000 r/min and no separate thermal reference is published; at dm ≈ 72.5 mm the corresponding dn is approximately 870k mm·r/min. Sizing arithmetic on the 45 mm bore: 100 kN C divided by the 27.5 mm radial section height gives 3.6 kN per section millimetre; the 1050 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 12,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is NOT built into QJ-309-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-309-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 309 MA as the qj plain execution; the other order numbers of the QJ 309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-309-MA?",
        "a": "QJ 309 MA measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 1050 g. SKF 17000 ratings: C 100 kN, C0 83 kN, Pu 3.55 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-309-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7309 BEP shares the 45×100×25 mm angular-contact envelope, but catalogue C/C0 differ (100/83 kN vs 55.9/37.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-309-MA",
      "QJ 309 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-309-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 309 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 100,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 309 N2PHAS is SKF's 45 mm-bore QJ four-point contact ball bearing of the QJ300 series, 45×100×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 100 kN, C0 83 kN, Pu 3.55 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 1050 g. Sizing arithmetic on the 45 mm bore: 100 kN C divided by the 27.5 mm radial section height gives 3.6 kN per section millimetre; the 1050 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 3.55 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 100/83 kN ratings and 1050 g mass this execution carries about 2.22 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 12,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-309-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-309-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 309 N2PHAS as the qj slotted execution; the other order numbers of the QJ 309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-309-N2PHAS?",
        "a": "QJ 309 N2PHAS measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 1050 g. SKF 17000 ratings: C 100 kN, C0 83 kN, Pu 3.55 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 309 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7309 BEP shares the 45×100×25 mm angular-contact envelope, but catalogue C/C0 differ (100/83 kN vs 55.9/37.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-309-N2PHAS",
      "QJ 309 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-309-PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 309 PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 45,
    "D_mm": 100,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 100,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 12000,
    "max_rpm": 12000,
    "weight_g": 1050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 309 PHAS is SKF's 45 mm-bore QJ four-point contact ball bearing of the QJ300 series, 45×100×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 45×100×25 mm (1.772×3.937×0.984 in), 27.5 mm radial section height, C 100 kN, C0 83 kN, Pu 3.55 kN.SKF publishes only the 12,000 r/min limiting speed for this execution, catalogue mass 1050 g. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 1050 g for 100 kN of dynamic capacity — about 11 g per rated kN. Selection figures for QJ 309 PHAS: the static-to-dynamic ratio C0/C is 0.83, Pu 3.55 kN is about 4 % of C, and catalogue mass works out to roughly 23 g per millimetre of bore. Bore-to-OD planning: OD 100 over bore 45 is a 2.22× step for this size, and the 25 mm width gives a bore/width ratio of 1.80; use these ratios when housing space around the 45 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "pump thrust positions",
      "clutch and brake assemblies",
      "textile machinery traverse drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is NOT built into QJ-309-PHAS: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The PHAS PEEK cage of QJ-309-PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 309 PHAS as the qj plain execution; the other order numbers of the QJ 309 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-309-PHAS?",
        "a": "QJ 309 PHAS measures 45 mm bore × 100 mm OD × 25 mm width (1.772 × 3.937 × 0.984 in), mass about 1050 g. SKF 17000 ratings: C 100 kN, C0 83 kN, Pu 3.55 kN, SKF publishes only the 12,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What does QJ mean in QJ 309 PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7309-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 55.9/37.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 61/40.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 64/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7309-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 45×100×25 mm envelope, but catalogue C/C0 differ between executions (100/83 kN vs 68/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-309-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-309-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 45×100×25 mm envelope with catalogue ratings within 10 %; QJ 309 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7309",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7309 BEP shares the 45×100×25 mm angular-contact envelope, but catalogue C/C0 differ (100/83 kN vs 55.9/37.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-309-PHAS",
      "QJ 309 PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-210-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 210 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 90,
    "B_mm": 20,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 65.5,
    "static_load_kN": 61,
    "fatigue_load_limit_kN": 2.6,
    "limiting_speed_rpm": 13000,
    "max_rpm": 13000,
    "weight_g": 590,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 210 MA is SKF's 50 mm-bore QJ four-point contact ball bearing of the QJ200 series, 50×90×20 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 50×90×20 mm (1.969×3.543×0.787 in), 20.0 mm radial section height, C 65.5 kN, C0 61 kN, Pu 2.6 kN.SKF publishes only the 13,000 r/min limiting speed for this execution, catalogue mass 590 g. Mass and section check: 590 g inside the 50×90×20 mm outline leaves a 20.0 mm radial section, and the 61 kN static rating is 0.93× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 61 kN against C 65.5 kN gives a 0.93 ratio, typical of a four-point thrust-oriented design; Pu 2.6 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 13,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives",
      "pump thrust positions"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is NOT built into QJ-210-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-210-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 210 MA as the qj plain execution; the other order numbers of the QJ 210 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-210-MA?",
        "a": "QJ 210 MA measures 50 mm bore × 90 mm OD × 20 mm width (1.969 × 3.543 × 0.787 in), mass about 590 g. SKF 17000 ratings: C 65.5 kN, C0 61 kN, Pu 2.6 kN, SKF publishes only the 13,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-210-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7210-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 37.7/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 37.7/28.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 40/31 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 40/31 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 40/31 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 41.5/33.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×90×20 mm envelope, but catalogue C/C0 differ between executions (65.5/61 kN vs 45.5/35.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7210",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7210 BEP shares the 50×90×20 mm angular-contact envelope, but catalogue C/C0 differ (65.5/61 kN vs 37.7/28.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-210-MA",
      "QJ 210 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-310-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 310 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 118,
    "static_load_kN": 100,
    "fatigue_load_limit_kN": 4.25,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 310 MA is SKF's 50 mm-bore QJ four-point contact ball bearing of the QJ300 series, 50×110×27 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 118 kN, C0 100 kN, Pu 4.25 kN.SKF publishes only the 11,000 r/min limiting speed for this execution, catalogue mass 1350 g. Envelope economics: the 27 mm width over a 30.0 mm section yields 0.90 mm of ring width per section millimetre, and the bearing weighs 1350 g for 118 kN of dynamic capacity — about 11 g per rated kN. Mass and section check: 1350 g inside the 50×110×27 mm outline leaves a 30.0 mm radial section, and the 100 kN static rating is 0.85× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 11,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Anti-rotation is NOT built into QJ-310-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-310-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 310 MA as the qj plain execution; the other order numbers of the QJ 310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-310-MA?",
        "a": "QJ 310 MA measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1350 g. SKF 17000 ratings: C 118 kN, C0 100 kN, Pu 4.25 kN, SKF publishes only the 11,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 310 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 68.9/47.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 78/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 83/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; QJ 310 PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7310 BECBP shares the 50×110×27 mm angular-contact envelope, but catalogue C/C0 differ (118/100 kN vs 75/51 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-310-MA",
      "QJ 310 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-310-PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 310 PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 50,
    "D_mm": 110,
    "B_mm": 27,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 118,
    "static_load_kN": 100,
    "fatigue_load_limit_kN": 4.25,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 1350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 310 PHAS is SKF's 50 mm-bore QJ four-point contact ball bearing of the QJ300 series, 50×110×27 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 50×110×27 mm (1.969×4.331×1.063 in), 30.0 mm radial section height, C 118 kN, C0 100 kN, Pu 4.25 kN.SKF publishes only the 11,000 r/min limiting speed for this execution, catalogue mass 1350 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 11,000 r/min and no separate thermal reference is published; at dm ≈ 80.0 mm the corresponding dn is approximately 880k mm·r/min. At the printed limiting speed of 11,000 r/min the mean pitch diameter dm ≈ 80.0 mm implies a dn value around 880k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 110 over bore 50 is a 2.20× step for this size, and the 27 mm width gives a bore/width ratio of 1.85; use these ratios when housing space around the 50 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "pump thrust positions",
      "clutch and brake assemblies",
      "textile machinery traverse drives"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is NOT built into QJ-310-PHAS: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The PHAS PEEK cage of QJ-310-PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 310 PHAS as the qj plain execution; the other order numbers of the QJ 310 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-310-PHAS?",
        "a": "QJ 310 PHAS measures 50 mm bore × 110 mm OD × 27 mm width (1.969 × 4.331 × 1.063 in), mass about 1350 g. SKF 17000 ratings: C 118 kN, C0 100 kN, Pu 4.25 kN, SKF publishes only the 11,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What minimum axial load does QJ-310-PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7310-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 68.9/47.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 75/51 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 78/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7310-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 50×110×27 mm envelope, but catalogue C/C0 differ between executions (118/100 kN vs 83/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-310-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 50×110×27 mm envelope with catalogue ratings within 10 %; QJ 310 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7310",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7310 BECBP shares the 50×110×27 mm angular-contact envelope, but catalogue C/C0 differ (118/100 kN vs 75/51 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-310-PHAS",
      "QJ 310 PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-211-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 211 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 85,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 211 N2MA is SKF's 55 mm-bore QJ four-point contact ball bearing of the QJ200 series, 55×100×21 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 85 kN, C0 83 kN, Pu 3.55 kN.SKF publishes only the 11,000 r/min limiting speed for this execution, catalogue mass 770 g. The 3.55 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 85/83 kN ratings and 770 g mass this execution carries about 1.55 kN of C per millimetre of bore. Selection figures for QJ 211 N2MA: the static-to-dynamic ratio C0/C is 0.98, Pu 3.55 kN is about 4 % of C, and catalogue mass works out to roughly 14 g per millimetre of bore. Bore-to-OD planning: OD 100 over bore 55 is a 1.82× step for this size, and the 21 mm width gives a bore/width ratio of 2.62; use these ratios when housing space around the 55 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw and worm drives",
      "pump thrust positions",
      "clutch and brake assemblies"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-211-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-211-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 211 N2MA as the qj slotted execution; the other order numbers of the QJ 211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-211-N2MA?",
        "a": "QJ 211 N2MA measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 770 g. SKF 17000 ratings: C 85 kN, C0 83 kN, Pu 3.55 kN, SKF publishes only the 11,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 211 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 51/42.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; QJ 211 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (85/83 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-211-N2MA",
      "QJ 211 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-211-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 211 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 100,
    "B_mm": 21,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 85,
    "static_load_kN": 83,
    "fatigue_load_limit_kN": 3.55,
    "limiting_speed_rpm": 11000,
    "max_rpm": 11000,
    "weight_g": 770,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 211 MA is SKF's 55 mm-bore QJ four-point contact ball bearing of the QJ200 series, 55×100×21 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 55×100×21 mm (2.165×3.937×0.827 in), 22.5 mm radial section height, C 85 kN, C0 83 kN, Pu 3.55 kN.SKF publishes only the 11,000 r/min limiting speed for this execution, catalogue mass 770 g. Selection figures for QJ 211 MA: the static-to-dynamic ratio C0/C is 0.98, Pu 3.55 kN is about 4 % of C, and catalogue mass works out to roughly 14 g per millimetre of bore. Load balance: C0 83 kN against C 85 kN gives a 0.98 ratio, typical of a four-point thrust-oriented design; Pu 3.55 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 11,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "clutch and brake assemblies",
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is NOT built into QJ-211-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-211-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 211 MA as the qj plain execution; the other order numbers of the QJ 211 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-211-MA?",
        "a": "QJ 211 MA measures 55 mm bore × 100 mm OD × 21 mm width (2.165 × 3.937 × 0.827 in), mass about 770 g. SKF 17000 ratings: C 85 kN, C0 83 kN, Pu 3.55 kN, SKF publishes only the 11,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 211 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7211-BE-2RZP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 46.2/36 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 49/40 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 51/42.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7211-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×100×21 mm envelope, but catalogue C/C0 differ between executions (85/83 kN vs 57/45 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-211-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×100×21 mm envelope with catalogue ratings within 10 %; QJ 211 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7211",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7211 BEP shares the 55×100×21 mm angular-contact envelope, but catalogue C/C0 differ (85/83 kN vs 46.2/36 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-211-MA",
      "QJ 211 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-311-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 311 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 137,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 5,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 311 N2MA is SKF's 55 mm-bore QJ four-point contact ball bearing of the QJ300 series, 55×120×29 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 137 kN, C0 118 kN, Pu 5 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 1750 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 10,000 r/min and no separate thermal reference is published; at dm ≈ 87.5 mm the corresponding dn is approximately 875k mm·r/min. At the printed limiting speed of 10,000 r/min the mean pitch diameter dm ≈ 87.5 mm implies a dn value around 875k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 120 over bore 55 is a 2.18× step for this size, and the 29 mm width gives a bore/width ratio of 1.90; use these ratios when housing space around the 55 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "pump thrust positions",
      "clutch and brake assemblies",
      "textile machinery traverse drives"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is built into QJ-311-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-311-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 311 N2MA as the qj slotted execution; the other order numbers of the QJ 311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-311-N2MA?",
        "a": "QJ 311 N2MA measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1750 g. SKF 17000 ratings: C 137 kN, C0 118 kN, Pu 5 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-311-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 79.3/55 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 90/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 96.5/67 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; QJ 311 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7311 BEP shares the 55×120×29 mm angular-contact envelope, but catalogue C/C0 differ (137/118 kN vs 79.3/55 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-311-N2MA",
      "QJ 311 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-311-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 311 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 55,
    "D_mm": 120,
    "B_mm": 29,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 137,
    "static_load_kN": 118,
    "fatigue_load_limit_kN": 5,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 1750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 311 MA is SKF's 55 mm-bore QJ four-point contact ball bearing of the QJ300 series, 55×120×29 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 55×120×29 mm (2.165×4.724×1.142 in), 32.5 mm radial section height, C 137 kN, C0 118 kN, Pu 5 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 1750 g. Load balance: C0 118 kN against C 137 kN gives a 0.86 ratio, typical of a four-point thrust-oriented design; Pu 5 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 1750 g inside the 55×120×29 mm outline leaves a 32.5 mm radial section, and the 118 kN static rating is 0.86× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 10,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "textile machinery traverse drives",
      "gearbox shafts where one QJ locates axially in both directions beside a radial bearing",
      "screw and worm drives"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is NOT built into QJ-311-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-311-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 311 MA as the qj plain execution; the other order numbers of the QJ 311 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-311-MA?",
        "a": "QJ 311 MA measures 55 mm bore × 120 mm OD × 29 mm width (2.165 × 4.724 × 1.142 in), mass about 1750 g. SKF 17000 ratings: C 137 kN, C0 118 kN, Pu 5 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-311-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7311-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 79.3/55 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 85/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 90/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7311-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 55×120×29 mm envelope, but catalogue C/C0 differ between executions (137/118 kN vs 96.5/67 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-311-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 55×120×29 mm envelope with catalogue ratings within 10 %; QJ 311 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7311",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7311 BEP shares the 55×120×29 mm angular-contact envelope, but catalogue C/C0 differ (137/118 kN vs 79.3/55 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-311-MA",
      "QJ 311 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-212-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 212 N2PHAS",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 96.5,
    "static_load_kN": 93,
    "fatigue_load_limit_kN": 4,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 990,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 212 N2PHAS is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ200 series, 60×110×22 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 96.5 kN, C0 93 kN, Pu 4 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 990 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 10,000 r/min and no separate thermal reference is published; at dm ≈ 85.0 mm the corresponding dn is approximately 850k mm·r/min. Sizing arithmetic on the 60 mm bore: 96.5 kN C divided by the 25.0 mm radial section height gives 3.9 kN per section millimetre; the 990 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 22 mm width gives a bore/width ratio of 2.73; use these ratios when housing space around the 60 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is built into QJ-212-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-212-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 212 N2PHAS as the qj slotted execution; the other order numbers of the QJ 212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-212-N2PHAS?",
        "a": "QJ 212 N2PHAS measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 990 g. SKF 17000 ratings: C 96.5 kN, C0 93 kN, Pu 4 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What minimum axial load does QJ-212-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 57.2/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; QJ 212 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; QJ 212 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7212 BEP shares the 60×110×22 mm angular-contact envelope, but catalogue C/C0 differ (96.5/93 kN vs 57.2/45.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-212-N2PHAS",
      "QJ 212 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-212-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 212 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 96.5,
    "static_load_kN": 93,
    "fatigue_load_limit_kN": 4,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 990,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 212 N2MA is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ200 series, 60×110×22 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 96.5 kN, C0 93 kN, Pu 4 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 990 g. Selection figures for QJ 212 N2MA: the static-to-dynamic ratio C0/C is 0.96, Pu 4 kN is about 4 % of C, and catalogue mass works out to roughly 17 g per millimetre of bore. Envelope economics: the 22 mm width over a 25.0 mm section yields 0.88 mm of ring width per section millimetre, and the bearing weighs 990 g for 96.5 kN of dynamic capacity — about 10 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 10,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-212-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-212-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 212 N2MA as the qj slotted execution; the other order numbers of the QJ 212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-212-N2MA?",
        "a": "QJ 212 N2MA measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 990 g. SKF 17000 ratings: C 96.5 kN, C0 93 kN, Pu 4 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 212 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 57.2/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; QJ 212 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-212-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; QJ 212 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7212 BEP shares the 60×110×22 mm angular-contact envelope, but catalogue C/C0 differ (96.5/93 kN vs 57.2/45.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-212-N2MA",
      "QJ 212 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-212-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 212 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 110,
    "B_mm": 22,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 96.5,
    "static_load_kN": 93,
    "fatigue_load_limit_kN": 4,
    "limiting_speed_rpm": 10000,
    "max_rpm": 10000,
    "weight_g": 990,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 212 MA is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ200 series, 60×110×22 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 60×110×22 mm (2.362×4.331×0.866 in), 25.0 mm radial section height, C 96.5 kN, C0 93 kN, Pu 4 kN.SKF publishes only the 10,000 r/min limiting speed for this execution, catalogue mass 990 g. Sizing arithmetic on the 60 mm bore: 96.5 kN C divided by the 25.0 mm radial section height gives 3.9 kN per section millimetre; the 990 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 96.5/93 kN ratings and 990 g mass this execution carries about 1.61 kN of C per millimetre of bore. Bore-to-OD planning: OD 110 over bore 60 is a 1.83× step for this size, and the 22 mm width gives a bore/width ratio of 2.73; use these ratios when housing space around the 60 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is NOT built into QJ-212-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-212-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 212 MA as the qj plain execution; the other order numbers of the QJ 212 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-212-MA?",
        "a": "QJ 212 MA measures 60 mm bore × 110 mm OD × 22 mm width (2.362 × 4.331 × 0.866 in), mass about 990 g. SKF 17000 ratings: C 96.5 kN, C0 93 kN, Pu 4 kN, SKF publishes only the 10,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 212 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7212-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 57.2/45.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 61/50 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7212-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×110×22 mm envelope, but catalogue C/C0 differ between executions (96.5/93 kN vs 69.5/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-212-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; QJ 212 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-212-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×110×22 mm envelope with catalogue ratings within 10 %; QJ 212 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7212",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7212 BEP shares the 60×110×22 mm angular-contact envelope, but catalogue C/C0 differ (96.5/93 kN vs 57.2/45.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-212-MA",
      "QJ 212 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-312-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 312 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 137,
    "fatigue_load_limit_kN": 5.85,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 312 N2MA is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ300 series, 60×130×31 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 156 kN, C0 137 kN, Pu 5.85 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 2150 g. Mass and section check: 2150 g inside the 60×130×31 mm outline leaves a 35.0 mm radial section, and the 137 kN static rating is 0.88× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 9,000 r/min the mean pitch diameter dm ≈ 95.0 mm implies a dn value around 855k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 9,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-312-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-312-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 312 N2MA as the qj slotted execution; the other order numbers of the QJ 312 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-312-N2MA?",
        "a": "QJ 312 N2MA measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 2150 g. SKF 17000 ratings: C 156 kN, C0 137 kN, Pu 5.85 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-312-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; QJ 312 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; QJ 312 PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (156/137 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-312-N2MA",
      "QJ 312 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-312-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 312 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 137,
    "fatigue_load_limit_kN": 5.85,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 312 MA is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ300 series, 60×130×31 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 156 kN, C0 137 kN, Pu 5.85 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 2150 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min and no separate thermal reference is published; at dm ≈ 95.0 mm the corresponding dn is approximately 855k mm·r/min. Sizing arithmetic on the 60 mm bore: 156 kN C divided by the 35.0 mm radial section height gives 4.5 kN per section millimetre; the 2150 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 130 over bore 60 is a 2.17× step for this size, and the 31 mm width gives a bore/width ratio of 1.94; use these ratios when housing space around the 60 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is NOT built into QJ-312-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-312-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 312 MA as the qj plain execution; the other order numbers of the QJ 312 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-312-MA?",
        "a": "QJ 312 MA measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 2150 g. SKF 17000 ratings: C 156 kN, C0 137 kN, Pu 5.85 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-312-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; QJ 312 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-312-PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; QJ 312 PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (156/137 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-312-MA",
      "QJ 312 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-312-PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 312 PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 60,
    "D_mm": 130,
    "B_mm": 31,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 156,
    "static_load_kN": 137,
    "fatigue_load_limit_kN": 5.85,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 2150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 312 PHAS is SKF's 60 mm-bore QJ four-point contact ball bearing of the QJ300 series, 60×130×31 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 60×130×31 mm (2.362×5.118×1.22 in), 35.0 mm radial section height, C 156 kN, C0 137 kN, Pu 5.85 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 2150 g. Envelope economics: the 31 mm width over a 35.0 mm section yields 0.89 mm of ring width per section millimetre, and the bearing weighs 2150 g for 156 kN of dynamic capacity — about 14 g per rated kN. Selection figures for QJ 312 PHAS: the static-to-dynamic ratio C0/C is 0.88, Pu 5.85 kN is about 4 % of C, and catalogue mass works out to roughly 36 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 9,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is NOT built into QJ-312-PHAS: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The PHAS PEEK cage of QJ-312-PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 312 PHAS as the qj plain execution; the other order numbers of the QJ 312 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-312-PHAS?",
        "a": "QJ 312 PHAS measures 60 mm bore × 130 mm OD × 31 mm width (2.362 × 5.118 × 1.22 in), mass about 2150 g. SKF 17000 ratings: C 156 kN, C0 137 kN, Pu 5.85 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What does QJ mean in QJ 312 PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7312-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 95.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 104/76.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7312-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 60×130×31 mm envelope, but catalogue C/C0 differ between executions (156/137 kN vs 116/85 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-312-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; QJ 312 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-312-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 60×130×31 mm envelope with catalogue ratings within 10 %; QJ 312 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7312",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7312 BEP shares the 60×130×31 mm angular-contact envelope, but catalogue C/C0 differ (156/137 kN vs 95.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-312-PHAS",
      "QJ 312 PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-213-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 213 N2PHAS",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 110,
    "static_load_kN": 112,
    "fatigue_load_limit_kN": 4.75,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 213 N2PHAS is SKF's 65 mm-bore QJ four-point contact ball bearing of the QJ200 series, 65×120×23 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 110 kN, C0 112 kN, Pu 4.75 kN.SKF publishes only the 9,500 r/min limiting speed for this execution, catalogue mass 1200 g. The 4.75 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 110/112 kN ratings and 1200 g mass this execution carries about 1.69 kN of C per millimetre of bore. Sizing arithmetic on the 65 mm bore: 110 kN C divided by the 27.5 mm radial section height gives 4.0 kN per section millimetre; the 1200 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 120 over bore 65 is a 1.85× step for this size, and the 23 mm width gives a bore/width ratio of 2.83; use these ratios when housing space around the 65 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "Anti-rotation is built into QJ-213-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-213-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 213 N2PHAS as the qj slotted execution; the other order numbers of the QJ 213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-213-N2PHAS?",
        "a": "QJ 213 N2PHAS measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1200 g. SKF 17000 ratings: C 110 kN, C0 112 kN, Pu 4.75 kN, SKF publishes only the 9,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 213 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 66.3/54 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; QJ 213 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; QJ 213 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7213 BEP shares the 65×120×23 mm angular-contact envelope, but catalogue C/C0 differ (110/112 kN vs 66.3/54 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-213-N2PHAS",
      "QJ 213 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-213-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 213 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 110,
    "static_load_kN": 112,
    "fatigue_load_limit_kN": 4.75,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 213 N2MA is SKF's 65 mm-bore QJ four-point contact ball bearing of the QJ200 series, 65×120×23 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 110 kN, C0 112 kN, Pu 4.75 kN.SKF publishes only the 9,500 r/min limiting speed for this execution, catalogue mass 1200 g. Load balance: C0 112 kN against C 110 kN gives a 1.02 ratio, typical of a four-point thrust-oriented design; Pu 4.75 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,500 r/min and no separate thermal reference is published; at dm ≈ 92.5 mm the corresponding dn is approximately 879k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 9,500 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is built into QJ-213-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-213-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 213 N2MA as the qj slotted execution; the other order numbers of the QJ 213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-213-N2MA?",
        "a": "QJ 213 N2MA measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1200 g. SKF 17000 ratings: C 110 kN, C0 112 kN, Pu 4.75 kN, SKF publishes only the 9,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-213-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 66.3/54 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; QJ 213 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-213-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; QJ 213 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7213 BEP shares the 65×120×23 mm angular-contact envelope, but catalogue C/C0 differ (110/112 kN vs 66.3/54 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-213-N2MA",
      "QJ 213 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-213-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 213 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 120,
    "B_mm": 23,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 110,
    "static_load_kN": 112,
    "fatigue_load_limit_kN": 4.75,
    "limiting_speed_rpm": 9500,
    "max_rpm": 9500,
    "weight_g": 1200,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 213 MA is SKF's 65 mm-bore QJ four-point contact ball bearing of the QJ200 series, 65×120×23 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 65×120×23 mm (2.559×4.724×0.906 in), 27.5 mm radial section height, C 110 kN, C0 112 kN, Pu 4.75 kN.SKF publishes only the 9,500 r/min limiting speed for this execution, catalogue mass 1200 g. At the printed limiting speed of 9,500 r/min the mean pitch diameter dm ≈ 92.5 mm implies a dn value around 879k mm·r/min; only the limiting speed is published for this execution. The 4.75 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 110/112 kN ratings and 1200 g mass this execution carries about 1.69 kN of C per millimetre of bore. Bore-to-OD planning: OD 120 over bore 65 is a 1.85× step for this size, and the 23 mm width gives a bore/width ratio of 2.83; use these ratios when housing space around the 65 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is NOT built into QJ-213-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-213-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 213 MA as the qj plain execution; the other order numbers of the QJ 213 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-213-MA?",
        "a": "QJ 213 MA measures 65 mm bore × 120 mm OD × 23 mm width (2.559 × 4.724 × 0.906 in), mass about 1200 g. SKF 17000 ratings: C 110 kN, C0 112 kN, Pu 4.75 kN, SKF publishes only the 9,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-213-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7213-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 66.3/54 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 69.5/57 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7213-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×120×23 mm envelope, but catalogue C/C0 differ between executions (110/112 kN vs 81.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-213-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; QJ 213 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-213-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×120×23 mm envelope with catalogue ratings within 10 %; QJ 213 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7213",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7213 BEP shares the 65×120×23 mm angular-contact envelope, but catalogue C/C0 differ (110/112 kN vs 66.3/54 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-213-MA",
      "QJ 213 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-313-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 313 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 176,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 6.55,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 313 N2PHAS is SKF's 65 mm-bore QJ four-point contact ball bearing of the QJ300 series, 65×140×33 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 176 kN, C0 156 kN, Pu 6.55 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 2700 g. At the printed limiting speed of 8,500 r/min the mean pitch diameter dm ≈ 102.5 mm implies a dn value around 871k mm·r/min; only the limiting speed is published for this execution. The 6.55 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 176/156 kN ratings and 2700 g mass this execution carries about 2.71 kN of C per millimetre of bore. Bore-to-OD planning: OD 140 over bore 65 is a 2.15× step for this size, and the 33 mm width gives a bore/width ratio of 1.97; use these ratios when housing space around the 65 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-313-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-313-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 313 N2PHAS as the qj slotted execution; the other order numbers of the QJ 313 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-313-N2PHAS?",
        "a": "QJ 313 N2PHAS measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2700 g. SKF 17000 ratings: C 176 kN, C0 156 kN, Pu 6.55 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What minimum axial load does QJ-313-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 108/80 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; QJ 313 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7313 BEP shares the 65×140×33 mm angular-contact envelope, but catalogue C/C0 differ (176/156 kN vs 108/80 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-313-N2PHAS",
      "QJ 313 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-313-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 313 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 65,
    "D_mm": 140,
    "B_mm": 33,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 176,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 6.55,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 2700,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 313 MA is SKF's 65 mm-bore QJ four-point contact ball bearing of the QJ300 series, 65×140×33 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 65×140×33 mm (2.559×5.512×1.299 in), 37.5 mm radial section height, C 176 kN, C0 156 kN, Pu 6.55 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 2700 g. The 6.55 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 176/156 kN ratings and 2700 g mass this execution carries about 2.71 kN of C per millimetre of bore. Sizing arithmetic on the 65 mm bore: 176 kN C divided by the 37.5 mm radial section height gives 4.7 kN per section millimetre; the 2700 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 140 over bore 65 is a 2.15× step for this size, and the 33 mm width gives a bore/width ratio of 1.97; use these ratios when housing space around the 65 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is NOT built into QJ-313-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-313-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 313 MA as the qj plain execution; the other order numbers of the QJ 313 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-313-MA?",
        "a": "QJ 313 MA measures 65 mm bore × 140 mm OD × 33 mm width (2.559 × 5.512 × 1.299 in), mass about 2700 g. SKF 17000 ratings: C 176 kN, C0 156 kN, Pu 6.55 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 313 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7313-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 108/80 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 116/86.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7313-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 65×140×33 mm envelope, but catalogue C/C0 differ between executions (176/156 kN vs 132/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-313-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 65×140×33 mm envelope with catalogue ratings within 10 %; QJ 313 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7313",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7313 BEP shares the 65×140×33 mm angular-contact envelope, but catalogue C/C0 differ (176/156 kN vs 108/80 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-313-MA",
      "QJ 313 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-214-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 214 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 120,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 5.2,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 214 N2MA is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ200 series, 70×125×24 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 120 kN, C0 122 kN, Pu 5.2 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 1300 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 9,000 r/min and no separate thermal reference is published; at dm ≈ 97.5 mm the corresponding dn is approximately 878k mm·r/min. At the printed limiting speed of 9,000 r/min the mean pitch diameter dm ≈ 97.5 mm implies a dn value around 878k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 125 over bore 70 is a 1.79× step for this size, and the 24 mm width gives a bore/width ratio of 2.92; use these ratios when housing space around the 70 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "paper-machine calender stacks",
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-214-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-214-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 214 N2MA as the qj slotted execution; the other order numbers of the QJ 214 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-214-N2MA?",
        "a": "QJ 214 N2MA measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1300 g. SKF 17000 ratings: C 120 kN, C0 122 kN, Pu 5.2 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-214-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 67.6/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 75/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; QJ 214 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; QJ 214 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7214 BEP shares the 70×125×24 mm angular-contact envelope, but catalogue C/C0 differ (120/122 kN vs 67.6/56 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-214-N2MA",
      "QJ 214 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-214-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 214 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 120,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 5.2,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 214 MA is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ200 series, 70×125×24 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 120 kN, C0 122 kN, Pu 5.2 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 1300 g. Load balance: C0 122 kN against C 120 kN gives a 1.02 ratio, typical of a four-point thrust-oriented design; Pu 5.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 1300 g inside the 70×125×24 mm outline leaves a 27.5 mm radial section, and the 122 kN static rating is 1.02× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 9,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "paper-machine calender stacks",
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is NOT built into QJ-214-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-214-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 214 MA as the qj plain execution; the other order numbers of the QJ 214 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-214-MA?",
        "a": "QJ 214 MA measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1300 g. SKF 17000 ratings: C 120 kN, C0 122 kN, Pu 5.2 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-214-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 67.6/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 75/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; QJ 214 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-214-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; QJ 214 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7214 BEP shares the 70×125×24 mm angular-contact envelope, but catalogue C/C0 differ (120/122 kN vs 67.6/56 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-214-MA",
      "QJ 214 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-214-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 214 N2PHAS",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 125,
    "B_mm": 24,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 120,
    "static_load_kN": 122,
    "fatigue_load_limit_kN": 5.2,
    "limiting_speed_rpm": 9000,
    "max_rpm": 9000,
    "weight_g": 1300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 214 N2PHAS is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ200 series, 70×125×24 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 70×125×24 mm (2.756×4.921×0.945 in), 27.5 mm radial section height, C 120 kN, C0 122 kN, Pu 5.2 kN.SKF publishes only the 9,000 r/min limiting speed for this execution, catalogue mass 1300 g. Selection figures for QJ 214 N2PHAS: the static-to-dynamic ratio C0/C is 1.02, Pu 5.2 kN is about 4 % of C, and catalogue mass works out to roughly 19 g per millimetre of bore. Load balance: C0 122 kN against C 120 kN gives a 1.02 ratio, typical of a four-point thrust-oriented design; Pu 5.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 9,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-214-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-214-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 214 N2PHAS as the qj slotted execution; the other order numbers of the QJ 214 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-214-N2PHAS?",
        "a": "QJ 214 N2PHAS measures 70 mm bore × 125 mm OD × 24 mm width (2.756 × 4.921 × 0.945 in), mass about 1300 g. SKF 17000 ratings: C 120 kN, C0 122 kN, Pu 5.2 kN, SKF publishes only the 9,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What does QJ mean in QJ 214 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7214-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 67.6/56 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 72/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 75/64 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7214-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×125×24 mm envelope, but catalogue C/C0 differ between executions (120/122 kN vs 83/68 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-214-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; QJ 214 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-214-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×125×24 mm envelope with catalogue ratings within 10 %; QJ 214 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7214",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7214 BEP shares the 70×125×24 mm angular-contact envelope, but catalogue C/C0 differ (120/122 kN vs 67.6/56 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-214-N2PHAS",
      "QJ 214 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-314-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 314 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 200,
    "static_load_kN": 180,
    "fatigue_load_limit_kN": 7.35,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 3150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 314 N2MA is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ300 series, 70×150×35 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 200 kN, C0 180 kN, Pu 7.35 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 3150 g. The 7.35 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 200/180 kN ratings and 3150 g mass this execution carries about 2.86 kN of C per millimetre of bore. Selection figures for QJ 314 N2MA: the static-to-dynamic ratio C0/C is 0.90, Pu 7.35 kN is about 4 % of C, and catalogue mass works out to roughly 45 g per millimetre of bore. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-314-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-314-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 314 N2MA as the qj slotted execution; the other order numbers of the QJ 314 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-314-N2MA?",
        "a": "QJ 314 N2MA measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 3150 g. SKF 17000 ratings: C 200 kN, C0 180 kN, Pu 7.35 kN, SKF publishes only the 8,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 314 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 119/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; QJ 314 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; QJ 314 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7314 BEP shares the 70×150×35 mm angular-contact envelope, but catalogue C/C0 differ (200/180 kN vs 119/90 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-314-N2MA",
      "QJ 314 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-314-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 314 MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 200,
    "static_load_kN": 180,
    "fatigue_load_limit_kN": 7.35,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 3150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 314 MA is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ300 series, 70×150×35 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 200 kN, C0 180 kN, Pu 7.35 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 3150 g. Selection figures for QJ 314 MA: the static-to-dynamic ratio C0/C is 0.90, Pu 7.35 kN is about 4 % of C, and catalogue mass works out to roughly 45 g per millimetre of bore. Load balance: C0 180 kN against C 200 kN gives a 0.90 ratio, typical of a four-point thrust-oriented design; Pu 7.35 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,000 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is NOT built into QJ-314-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-314-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 314 MA as the qj plain execution; the other order numbers of the QJ 314 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-314-MA?",
        "a": "QJ 314 MA measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 3150 g. SKF 17000 ratings: C 200 kN, C0 180 kN, Pu 7.35 kN, SKF publishes only the 8,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 314 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 119/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; QJ 314 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-314-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; QJ 314 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7314 BEP shares the 70×150×35 mm angular-contact envelope, but catalogue C/C0 differ (200/180 kN vs 119/90 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-314-MA",
      "QJ 314 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-314-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 314 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 70,
    "D_mm": 150,
    "B_mm": 35,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 200,
    "static_load_kN": 180,
    "fatigue_load_limit_kN": 7.35,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 3150,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 314 N2PHAS is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ300 series, 70×150×35 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 200 kN, C0 180 kN, Pu 7.35 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 3150 g. Load balance: C0 180 kN against C 200 kN gives a 0.90 ratio, typical of a four-point thrust-oriented design; Pu 7.35 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 3150 g inside the 70×150×35 mm outline leaves a 40.0 mm radial section, and the 180 kN static rating is 0.90× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "paper-machine calender stacks",
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "Anti-rotation is built into QJ-314-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-314-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 314 N2PHAS as the qj slotted execution; the other order numbers of the QJ 314 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-314-N2PHAS?",
        "a": "QJ 314 N2PHAS measures 70 mm bore × 150 mm OD × 35 mm width (2.756 × 5.906 × 1.378 in), mass about 3150 g. SKF 17000 ratings: C 200 kN, C0 180 kN, Pu 7.35 kN, SKF publishes only the 8,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-314-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7314-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 119/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 127/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7314-ACCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 70×150×35 mm envelope, but catalogue C/C0 differ between executions (200/180 kN vs 143/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-314-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; QJ 314 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-314-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 70×150×35 mm envelope with catalogue ratings within 10 %; QJ 314 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7314",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7314 BEP shares the 70×150×35 mm angular-contact envelope, but catalogue C/C0 differ (200/180 kN vs 119/90 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-314-N2PHAS",
      "QJ 314 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-215-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 215 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 125,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 5.6,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 215 N2MA is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ200 series, 75×130×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 125 kN, C0 132 kN, Pu 5.6 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 1450 g. Sizing arithmetic on the 75 mm bore: 125 kN C divided by the 27.5 mm radial section height gives 4.5 kN per section millimetre; the 1450 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 1450 g for 125 kN of dynamic capacity — about 12 g per rated kN. Bore-to-OD planning: OD 130 over bore 75 is a 1.73× step for this size, and the 25 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 75 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "paper-machine calender stacks",
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-215-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-215-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 215 N2MA as the qj slotted execution; the other order numbers of the QJ 215 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-215-N2MA?",
        "a": "QJ 215 N2MA measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1450 g. SKF 17000 ratings: C 125 kN, C0 132 kN, Pu 5.6 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 215 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 70.2/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 76.5/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; QJ 215 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; QJ 215 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7215 BEP shares the 75×130×25 mm angular-contact envelope, but catalogue C/C0 differ (125/132 kN vs 70.2/60 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-215-N2MA",
      "QJ 215 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-215-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 215 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 125,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 5.6,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 215 MA is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ200 series, 75×130×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 125 kN, C0 132 kN, Pu 5.6 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 1450 g. Envelope economics: the 25 mm width over a 27.5 mm section yields 0.91 mm of ring width per section millimetre, and the bearing weighs 1450 g for 125 kN of dynamic capacity — about 12 g per rated kN. Mass and section check: 1450 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 132 kN static rating is 1.06× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,500 r/min limiting value is the single published ceiling. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Without N2 slots, provide another positive anti-rotation feature for the radially loose outer ring",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is NOT built into QJ-215-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-215-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 215 MA as the qj plain execution; the other order numbers of the QJ 215 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-215-MA?",
        "a": "QJ 215 MA measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1450 g. SKF 17000 ratings: C 125 kN, C0 132 kN, Pu 5.6 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 215 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 70.2/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 76.5/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; QJ 215 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; QJ 215 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7215 BEP shares the 75×130×25 mm angular-contact envelope, but catalogue C/C0 differ (125/132 kN vs 70.2/60 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-215-MA",
      "QJ 215 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-215-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 215 N2PHAS",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 130,
    "B_mm": 25,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 125,
    "static_load_kN": 132,
    "fatigue_load_limit_kN": 5.6,
    "limiting_speed_rpm": 8500,
    "max_rpm": 8500,
    "weight_g": 1450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 215 N2PHAS is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ200 series, 75×130×25 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 75×130×25 mm (2.953×5.118×0.984 in), 27.5 mm radial section height, C 125 kN, C0 132 kN, Pu 5.6 kN.SKF publishes only the 8,500 r/min limiting speed for this execution, catalogue mass 1450 g. Mass and section check: 1450 g inside the 75×130×25 mm outline leaves a 27.5 mm radial section, and the 132 kN static rating is 1.06× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 132 kN against C 125 kN gives a 1.06 ratio, typical of a four-point thrust-oriented design; Pu 5.6 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,500 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-215-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-215-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 215 N2PHAS as the qj slotted execution; the other order numbers of the QJ 215 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-215-N2PHAS?",
        "a": "QJ 215 N2PHAS measures 75 mm bore × 130 mm OD × 25 mm width (2.953 × 5.118 × 0.984 in), mass about 1450 g. SKF 17000 ratings: C 125 kN, C0 132 kN, Pu 5.6 kN, SKF publishes only the 8,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-215-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7215-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 70.2/60 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 73.5/65.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7215-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×130×25 mm envelope, but catalogue C/C0 differ between executions (125/132 kN vs 76.5/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-215-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; QJ 215 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "QJ-215-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×130×25 mm envelope with catalogue ratings within 10 %; QJ 215 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7215",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7215 BEP shares the 75×130×25 mm angular-contact envelope, but catalogue C/C0 differ (125/132 kN vs 70.2/60 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-215-N2PHAS",
      "QJ 215 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-315-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 315 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 216,
    "static_load_kN": 200,
    "fatigue_load_limit_kN": 7.8,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 3900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 315 N2MA is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ300 series, 75×160×37 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 216 kN, C0 200 kN, Pu 7.8 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 3900 g. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 117.5 mm implies a dn value around 881k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min and no separate thermal reference is published; at dm ≈ 117.5 mm the corresponding dn is approximately 881k mm·r/min. Bore-to-OD planning: OD 160 over bore 75 is a 2.13× step for this size, and the 37 mm width gives a bore/width ratio of 2.03; use these ratios when housing space around the 75 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-315-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-315-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 315 N2MA as the qj slotted execution; the other order numbers of the QJ 315 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-315-N2MA?",
        "a": "QJ 315 N2MA measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3900 g. SKF 17000 ratings: C 216 kN, C0 200 kN, Pu 7.8 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-315-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 125/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; QJ 315 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7315 BEP shares the 75×160×37 mm angular-contact envelope, but catalogue C/C0 differ (216/200 kN vs 125/98 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-315-N2MA",
      "QJ 315 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-315-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 315 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 75,
    "D_mm": 160,
    "B_mm": 37,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 216,
    "static_load_kN": 200,
    "fatigue_load_limit_kN": 7.8,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 3900,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 315 N2PHAS is SKF's 75 mm-bore QJ four-point contact ball bearing of the QJ300 series, 75×160×37 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 75×160×37 mm (2.953×6.299×1.457 in), 42.5 mm radial section height, C 216 kN, C0 200 kN, Pu 7.8 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 3900 g. Envelope economics: the 37 mm width over a 42.5 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 3900 g for 216 kN of dynamic capacity — about 18 g per rated kN. Mass and section check: 3900 g inside the 75×160×37 mm outline leaves a 42.5 mm radial section, and the 200 kN static rating is 0.93× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,500 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-315-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-315-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 315 N2PHAS as the qj slotted execution; the other order numbers of the QJ 315 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-315-N2PHAS?",
        "a": "QJ 315 N2PHAS measures 75 mm bore × 160 mm OD × 37 mm width (2.953 × 6.299 × 1.457 in), mass about 3900 g. SKF 17000 ratings: C 216 kN, C0 200 kN, Pu 7.8 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What does QJ mean in QJ 315 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7315-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 125/98 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7315-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 75×160×37 mm envelope, but catalogue C/C0 differ between executions (216/200 kN vs 132/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-315-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 75×160×37 mm envelope with catalogue ratings within 10 %; QJ 315 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7315",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7315 BEP shares the 75×160×37 mm angular-contact envelope, but catalogue C/C0 differ (216/200 kN vs 125/98 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-315-N2PHAS",
      "QJ 315 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-216-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 216 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 146,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 6.4,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 216 N2MA is SKF's 80 mm-bore QJ four-point contact ball bearing of the QJ200 series, 80×140×26 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 146 kN, C0 156 kN, Pu 6.4 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 1850 g. Envelope economics: the 26 mm width over a 30.0 mm section yields 0.87 mm of ring width per section millimetre, and the bearing weighs 1850 g for 146 kN of dynamic capacity — about 13 g per rated kN. Selection figures for QJ 216 N2MA: the static-to-dynamic ratio C0/C is 1.07, Pu 6.4 kN is about 4 % of C, and catalogue mass works out to roughly 23 g per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-216-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-216-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 216 N2MA as the qj slotted execution; the other order numbers of the QJ 216 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-216-N2MA?",
        "a": "QJ 216 N2MA measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1850 g. SKF 17000 ratings: C 146 kN, C0 156 kN, Pu 6.4 kN, SKF publishes only the 8,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 216 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 80.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; QJ 216 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7216 BEP shares the 80×140×26 mm angular-contact envelope, but catalogue C/C0 differ (146/156 kN vs 80.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-216-N2MA",
      "QJ 216 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-216-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 216 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 140,
    "B_mm": 26,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 146,
    "static_load_kN": 156,
    "fatigue_load_limit_kN": 6.4,
    "limiting_speed_rpm": 8000,
    "max_rpm": 8000,
    "weight_g": 1850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 216 MA is SKF's 80 mm-bore QJ four-point contact ball bearing of the QJ200 series, 80×140×26 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 80×140×26 mm (3.15×5.512×1.024 in), 30.0 mm radial section height, C 146 kN, C0 156 kN, Pu 6.4 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 1850 g. The 6.4 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 146/156 kN ratings and 1850 g mass this execution carries about 1.82 kN of C per millimetre of bore. Sizing arithmetic on the 80 mm bore: 146 kN C divided by the 30.0 mm radial section height gives 4.9 kN per section millimetre; the 1850 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 140 over bore 80 is a 1.75× step for this size, and the 26 mm width gives a bore/width ratio of 3.08; use these ratios when housing space around the 80 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is NOT built into QJ-216-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-216-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 216 MA as the qj plain execution; the other order numbers of the QJ 216 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-216-MA?",
        "a": "QJ 216 MA measures 80 mm bore × 140 mm OD × 26 mm width (3.15 × 5.512 × 1.024 in), mass about 1850 g. SKF 17000 ratings: C 146 kN, C0 156 kN, Pu 6.4 kN, SKF publishes only the 8,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 216 MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7216-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 80.6/69.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7216-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×140×26 mm envelope, but catalogue C/C0 differ between executions (146/156 kN vs 85/75 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-216-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×140×26 mm envelope with catalogue ratings within 10 %; QJ 216 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7216",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7216 BEP shares the 80×140×26 mm angular-contact envelope, but catalogue C/C0 differ (146/156 kN vs 80.6/69.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-216-MA",
      "QJ 216 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-316-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 316 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 232,
    "static_load_kN": 228,
    "fatigue_load_limit_kN": 8.65,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 316 N2MA is SKF's 80 mm-bore QJ four-point contact ball bearing of the QJ300 series, 80×170×39 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 232 kN, C0 228 kN, Pu 8.65 kN.SKF publishes only the 7,000 r/min limiting speed for this execution, catalogue mass 4600 g. Load balance: C0 228 kN against C 232 kN gives a 0.98 ratio, typical of a four-point thrust-oriented design; Pu 8.65 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,000 r/min and no separate thermal reference is published; at dm ≈ 125.0 mm the corresponding dn is approximately 875k mm·r/min. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-316-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-316-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 316 N2MA as the qj slotted execution; the other order numbers of the QJ 316 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-316-N2MA?",
        "a": "QJ 316 N2MA measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 4600 g. SKF 17000 ratings: C 232 kN, C0 228 kN, Pu 8.65 kN, SKF publishes only the 7,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-316-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 135/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 135/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; QJ 316 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7316 BEP shares the 80×170×39 mm angular-contact envelope, but catalogue C/C0 differ (232/228 kN vs 135/110 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-316-N2MA",
      "QJ 316 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-316-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 316 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 80,
    "D_mm": 170,
    "B_mm": 39,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 232,
    "static_load_kN": 228,
    "fatigue_load_limit_kN": 8.65,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 4600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 316 N2PHAS is SKF's 80 mm-bore QJ four-point contact ball bearing of the QJ300 series, 80×170×39 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 80×170×39 mm (3.15×6.693×1.535 in), 45.0 mm radial section height, C 232 kN, C0 228 kN, Pu 8.65 kN.SKF publishes only the 7,000 r/min limiting speed for this execution, catalogue mass 4600 g. The 8.65 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 232/228 kN ratings and 4600 g mass this execution carries about 2.90 kN of C per millimetre of bore. Sizing arithmetic on the 80 mm bore: 232 kN C divided by the 45.0 mm radial section height gives 5.2 kN per section millimetre; the 4600 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 170 over bore 80 is a 2.13× step for this size, and the 39 mm width gives a bore/width ratio of 2.05; use these ratios when housing space around the 80 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "paper-machine calender stacks",
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is built into QJ-316-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-316-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 316 N2PHAS as the qj slotted execution; the other order numbers of the QJ 316 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-316-N2PHAS?",
        "a": "QJ 316 N2PHAS measures 80 mm bore × 170 mm OD × 39 mm width (3.15 × 6.693 × 1.535 in), mass about 4600 g. SKF 17000 ratings: C 232 kN, C0 228 kN, Pu 8.65 kN, SKF publishes only the 7,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 316 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7316-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 135/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 135/110 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7316-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 80×170×39 mm envelope, but catalogue C/C0 differ between executions (232/228 kN vs 143/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-316-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 80×170×39 mm envelope with catalogue ratings within 10 %; QJ 316 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7316",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7316 BEP shares the 80×170×39 mm angular-contact envelope, but catalogue C/C0 differ (232/228 kN vs 135/110 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-316-N2PHAS",
      "QJ 316 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-217-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 217 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 173,
    "fatigue_load_limit_kN": 6.7,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 2250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 217 N2MA is SKF's 85 mm-bore QJ four-point contact ball bearing of the QJ200 series, 85×150×28 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 85×150×28 mm (3.346×5.906×1.102 in), 32.5 mm radial section height, C 156 kN, C0 173 kN, Pu 6.7 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 2250 g. Mass and section check: 2250 g inside the 85×150×28 mm outline leaves a 32.5 mm radial section, and the 173 kN static rating is 1.11× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. At the printed limiting speed of 7,500 r/min the mean pitch diameter dm ≈ 117.5 mm implies a dn value around 881k mm·r/min; only the limiting speed is published for this execution. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 7,500 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-217-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-217-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 217 N2MA as the qj slotted execution; the other order numbers of the QJ 217 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-217-N2MA?",
        "a": "QJ 217 N2MA measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 2250 g. SKF 17000 ratings: C 156 kN, C0 173 kN, Pu 6.7 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-217-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 102/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 102/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 102/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-217-MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; QJ 217 MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7217 BEP shares the 85×150×28 mm angular-contact envelope, but catalogue C/C0 differ (156/173 kN vs 95.6/83 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-217-N2MA",
      "QJ 217 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-217-MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 217 MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 150,
    "B_mm": 28,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 156,
    "static_load_kN": 173,
    "fatigue_load_limit_kN": 6.7,
    "limiting_speed_rpm": 7500,
    "max_rpm": 7500,
    "weight_g": 2250,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 217 MA is SKF's 85 mm-bore QJ four-point contact ball bearing of the QJ200 series, 85×150×28 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 85×150×28 mm (3.346×5.906×1.102 in), 32.5 mm radial section height, C 156 kN, C0 173 kN, Pu 6.7 kN.SKF publishes only the 7,500 r/min limiting speed for this execution, catalogue mass 2250 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,500 r/min and no separate thermal reference is published; at dm ≈ 117.5 mm the corresponding dn is approximately 881k mm·r/min. Sizing arithmetic on the 85 mm bore: 156 kN C divided by the 32.5 mm radial section height gives 4.8 kN per section millimetre; the 2250 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 150 over bore 85 is a 1.76× step for this size, and the 28 mm width gives a bore/width ratio of 3.04; use these ratios when housing space around the 85 mm shaft is the first constraint. Plain outer-ring execution: this order number is delivered without N2 locating slots, so anti-rotation is solved in the housing instead — a shoulder dog, a spring-loaded key, a cover feature or an interference-free circlip arrangement. Because the outer ring deliberately runs with radial clearance and a small axial float gap, omitting positive anti-rotation invites seat fretting; the slotted N2 order number is the alternative when the housing can provide engagement pins.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "outer-ring creep and seat fretting because the plain ring has no N2 slots and relies on housing-provided anti-rotation",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is NOT built into QJ-217-MA: without N2 slots the housing must provide a dog, keyed cover or other positive stop, since the outer ring runs radially loose by design.",
      "The MA brass cage of QJ-217-MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 217 MA as the qj plain execution; the other order numbers of the QJ 217 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-217-MA?",
        "a": "QJ 217 MA measures 85 mm bore × 150 mm OD × 28 mm width (3.346 × 5.906 × 1.102 in), mass about 2250 g. SKF 17000 ratings: C 156 kN, C0 173 kN, Pu 6.7 kN, SKF publishes only the 7,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-217-MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7217-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 95.6/83 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 102/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 102/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7217-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×150×28 mm envelope, but catalogue C/C0 differ between executions (156/173 kN vs 102/90 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-217-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 85×150×28 mm envelope with catalogue ratings within 10 %; QJ 217 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7217",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7217 BEP shares the 85×150×28 mm angular-contact envelope, but catalogue C/C0 differ (156/173 kN vs 95.6/83 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-217-MA",
      "QJ 217 MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-317-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 317 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 85,
    "D_mm": 180,
    "B_mm": 41,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 250,
    "static_load_kN": 255,
    "fatigue_load_limit_kN": 8.65,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 5450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 317 N2MA is SKF's 85 mm-bore QJ four-point contact ball bearing of the QJ300 series, 85×180×41 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 85×180×41 mm (3.346×7.087×1.614 in), 47.5 mm radial section height, C 250 kN, C0 255 kN, Pu 8.65 kN.SKF publishes only the 6,700 r/min limiting speed for this execution, catalogue mass 5450 g. Selection figures for QJ 317 N2MA: the static-to-dynamic ratio C0/C is 1.02, Pu 8.65 kN is about 3 % of C, and catalogue mass works out to roughly 64 g per millimetre of bore. Envelope economics: the 41 mm width over a 47.5 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 5450 g for 250 kN of dynamic capacity — about 22 g per rated kN. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,700 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is built into QJ-317-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-317-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 317 N2MA as the qj slotted execution; the other order numbers of the QJ 317 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-317-N2MA?",
        "a": "QJ 317 N2MA measures 85 mm bore × 180 mm OD × 41 mm width (3.346 × 7.087 × 1.614 in), mass about 5450 g. SKF 17000 ratings: C 250 kN, C0 255 kN, Pu 8.65 kN, SKF publishes only the 6,700 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 317 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7317-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (250/255 kN vs 146/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (250/255 kN vs 146/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (250/255 kN vs 156/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (250/255 kN vs 156/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (250/255 kN vs 156/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 85×180×41 mm envelope, but catalogue C/C0 differ between executions (250/255 kN vs 156/132 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7317",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7317 BEP shares the 85×180×41 mm angular-contact envelope, but catalogue C/C0 differ (250/255 kN vs 146/122 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-317-N2MA",
      "QJ 317 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-218-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 218 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 160,
    "B_mm": 30,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 186,
    "static_load_kN": 200,
    "fatigue_load_limit_kN": 7.65,
    "limiting_speed_rpm": 7000,
    "max_rpm": 7000,
    "weight_g": 2750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 218 N2MA is SKF's 90 mm-bore QJ four-point contact ball bearing of the QJ200 series, 90×160×30 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 90×160×30 mm (3.543×6.299×1.181 in), 35.0 mm radial section height, C 186 kN, C0 200 kN, Pu 7.65 kN.SKF publishes only the 7,000 r/min limiting speed for this execution, catalogue mass 2750 g. At the printed limiting speed of 7,000 r/min the mean pitch diameter dm ≈ 125.0 mm implies a dn value around 875k mm·r/min; only the limiting speed is published for this execution. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 7,000 r/min and no separate thermal reference is published; at dm ≈ 125.0 mm the corresponding dn is approximately 875k mm·r/min. Bore-to-OD planning: OD 160 over bore 90 is a 1.78× step for this size, and the 30 mm width gives a bore/width ratio of 3.00; use these ratios when housing space around the 90 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-218-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-218-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 218 N2MA as the qj slotted execution; the other order numbers of the QJ 218 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-218-N2MA?",
        "a": "QJ 218 N2MA measures 90 mm bore × 160 mm OD × 30 mm width (3.543 × 6.299 × 1.181 in), mass about 2750 g. SKF 17000 ratings: C 186 kN, C0 200 kN, Pu 7.65 kN, SKF publishes only the 7,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-218-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7218-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (186/200 kN vs 108/96.5 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (186/200 kN vs 116/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (186/200 kN vs 116/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×160×30 mm envelope, but catalogue C/C0 differ between executions (186/200 kN vs 116/104 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7218",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7218 BEP shares the 90×160×30 mm angular-contact envelope, but catalogue C/C0 differ (186/200 kN vs 108/96.5 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-218-N2MA",
      "QJ 218 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-318-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 318 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 285,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 11,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 6450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 318 N2MA is SKF's 90 mm-bore QJ four-point contact ball bearing of the QJ300 series, 90×190×43 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 285 kN, C0 305 kN, Pu 11 kN.SKF publishes only the 6,300 r/min limiting speed for this execution, catalogue mass 6450 g. Sizing arithmetic on the 90 mm bore: 285 kN C divided by the 50.0 mm radial section height gives 5.7 kN per section millimetre; the 6450 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Envelope economics: the 43 mm width over a 50.0 mm section yields 0.86 mm of ring width per section millimetre, and the bearing weighs 6450 g for 285 kN of dynamic capacity — about 23 g per rated kN. Bore-to-OD planning: OD 190 over bore 90 is a 2.11× step for this size, and the 43 mm width gives a bore/width ratio of 2.09; use these ratios when housing space around the 90 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "paper-machine calender stacks",
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-318-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-318-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 318 N2MA as the qj slotted execution; the other order numbers of the QJ 318 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-318-N2MA?",
        "a": "QJ 318 N2MA measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 6450 g. SKF 17000 ratings: C 285 kN, C0 305 kN, Pu 11 kN, SKF publishes only the 6,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 318 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 156/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 156/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; QJ 318 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7318 BEP shares the 90×190×43 mm angular-contact envelope, but catalogue C/C0 differ (285/305 kN vs 156/134 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-318-N2MA",
      "QJ 318 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-318-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 318 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 90,
    "D_mm": 190,
    "B_mm": 43,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 285,
    "static_load_kN": 305,
    "fatigue_load_limit_kN": 11,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 6450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 318 N2PHAS is SKF's 90 mm-bore QJ four-point contact ball bearing of the QJ300 series, 90×190×43 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 90×190×43 mm (3.543×7.48×1.693 in), 50.0 mm radial section height, C 285 kN, C0 305 kN, Pu 11 kN.SKF publishes only the 6,300 r/min limiting speed for this execution, catalogue mass 6450 g. Mass and section check: 6450 g inside the 90×190×43 mm outline leaves a 50.0 mm radial section, and the 305 kN static rating is 1.07× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 305 kN against C 285 kN gives a 1.07 ratio, typical of a four-point thrust-oriented design; Pu 11 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,300 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-318-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-318-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 318 N2PHAS as the qj slotted execution; the other order numbers of the QJ 318 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-318-N2PHAS?",
        "a": "QJ 318 N2PHAS measures 90 mm bore × 190 mm OD × 43 mm width (3.543 × 7.48 × 1.693 in), mass about 6450 g. SKF 17000 ratings: C 285 kN, C0 305 kN, Pu 11 kN, SKF publishes only the 6,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-318-N2PHAS require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7318-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 156/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 156/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7318-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 90×190×43 mm envelope, but catalogue C/C0 differ between executions (285/305 kN vs 166/146 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-318-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 90×190×43 mm envelope with catalogue ratings within 10 %; QJ 318 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7318",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7318 BEP shares the 90×190×43 mm angular-contact envelope, but catalogue C/C0 differ (285/305 kN vs 156/134 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-318-N2PHAS",
      "QJ 318 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-219-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 219 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 170,
    "B_mm": 32,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 212,
    "static_load_kN": 232,
    "fatigue_load_limit_kN": 8.5,
    "limiting_speed_rpm": 6700,
    "max_rpm": 6700,
    "weight_g": 3350,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 219 N2MA is SKF's 95 mm-bore QJ four-point contact ball bearing of the QJ200 series, 95×170×32 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 95×170×32 mm (3.74×6.693×1.26 in), 37.5 mm radial section height, C 212 kN, C0 232 kN, Pu 8.5 kN.SKF publishes only the 6,700 r/min limiting speed for this execution, catalogue mass 3350 g. The 8.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 212/232 kN ratings and 3350 g mass this execution carries about 2.23 kN of C per millimetre of bore. Selection figures for QJ 219 N2MA: the static-to-dynamic ratio C0/C is 1.09, Pu 8.5 kN is about 4 % of C, and catalogue mass works out to roughly 35 g per millimetre of bore. Bore-to-OD planning: OD 170 over bore 95 is a 1.79× step for this size, and the 32 mm width gives a bore/width ratio of 2.97; use these ratios when housing space around the 95 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "crane travel and hoist drives",
      "turret and slewing drives",
      "paper-machine calender stacks"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is built into QJ-219-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-219-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 219 N2MA as the qj slotted execution; the other order numbers of the QJ 219 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-219-N2MA?",
        "a": "QJ 219 N2MA measures 95 mm bore × 170 mm OD × 32 mm width (3.74 × 6.693 × 1.26 in), mass about 3350 g. SKF 17000 ratings: C 212 kN, C0 232 kN, Pu 8.5 kN, SKF publishes only the 6,700 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 219 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7219-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (212/232 kN vs 124/108 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (212/232 kN vs 129/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (212/232 kN vs 129/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219-BEGAPH",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (212/232 kN vs 129/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×170×32 mm envelope, but catalogue C/C0 differ between executions (212/232 kN vs 129/118 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7219",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7219 BEP shares the 95×170×32 mm angular-contact envelope, but catalogue C/C0 differ (212/232 kN vs 124/108 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-219-N2MA",
      "QJ 219 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-319-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 319 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 305,
    "static_load_kN": 340,
    "fatigue_load_limit_kN": 11.8,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 7450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 319 N2MA is SKF's 95 mm-bore QJ four-point contact ball bearing of the QJ300 series, 95×200×45 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 305 kN, C0 340 kN, Pu 11.8 kN.SKF publishes only the 6,000 r/min limiting speed for this execution, catalogue mass 7450 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 6,000 r/min and no separate thermal reference is published; at dm ≈ 147.5 mm the corresponding dn is approximately 885k mm·r/min. At the printed limiting speed of 6,000 r/min the mean pitch diameter dm ≈ 147.5 mm implies a dn value around 885k mm·r/min; only the limiting speed is published for this execution. Bore-to-OD planning: OD 200 over bore 95 is a 2.11× step for this size, and the 45 mm width gives a bore/width ratio of 2.11; use these ratios when housing space around the 95 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-319-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-319-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 319 N2MA as the qj slotted execution; the other order numbers of the QJ 319 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-319-N2MA?",
        "a": "QJ 319 N2MA measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 7450 g. SKF 17000 ratings: C 305 kN, C0 340 kN, Pu 11.8 kN, SKF publishes only the 6,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-319-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 168/150 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 168/150 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 180/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 180/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 180/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2PHAS",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; QJ 319 N2PHAS is the PEEK cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7319 BEP shares the 95×200×45 mm angular-contact envelope, but catalogue C/C0 differ (305/340 kN vs 168/150 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-319-N2MA",
      "QJ 319 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-319-N2PHAS",
    "brand": "SKF",
    "manufacturer_designation": "QJ 319 N2PHAS",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 95,
    "D_mm": 200,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "polymer",
    "dynamic_load_kN": 305,
    "static_load_kN": 340,
    "fatigue_load_limit_kN": 11.8,
    "limiting_speed_rpm": 6000,
    "max_rpm": 6000,
    "weight_g": 7450,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 319 N2PHAS is SKF's 95 mm-bore QJ four-point contact ball bearing of the QJ300 series, 95×200×45 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 95×200×45 mm (3.74×7.874×1.772 in), 52.5 mm radial section height, C 305 kN, C0 340 kN, Pu 11.8 kN.SKF publishes only the 6,000 r/min limiting speed for this execution, catalogue mass 7450 g. Selection figures for QJ 319 N2PHAS: the static-to-dynamic ratio C0/C is 1.11, Pu 11.8 kN is about 4 % of C, and catalogue mass works out to roughly 78 g per millimetre of bore. Load balance: C0 340 kN against C 305 kN gives a 1.11 ratio, typical of a four-point thrust-oriented design; Pu 11.8 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives",
      "turret and slewing drives"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-319-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The PHAS PEEK cage of QJ-319-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 319 N2PHAS as the qj slotted execution; the other order numbers of the QJ 319 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-319-N2PHAS?",
        "a": "QJ 319 N2PHAS measures 95 mm bore × 200 mm OD × 45 mm width (3.74 × 7.874 × 1.772 in), mass about 7450 g. SKF 17000 ratings: C 305 kN, C0 340 kN, Pu 11.8 kN, SKF publishes only the 6,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2PHAS suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication."
      },
      {
        "q": "What does QJ mean in QJ 319 N2PHAS?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7319-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 168/150 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 168/150 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 180/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 180/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7319-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 95×200×45 mm envelope, but catalogue C/C0 differ between executions (305/340 kN vs 180/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "QJ-319-N2MA",
        "equiv_brand": "SKF",
        "level": "full",
        "note": "Same 95×200×45 mm envelope with catalogue ratings within 10 %; QJ 319 N2MA is the brass cage, open arrangement, four-point split-inner-ring execution of this size — boundary dimensions interchangeable, execution differs."
      },
      {
        "equiv_sku": "7319",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7319 BEP shares the 95×200×45 mm angular-contact envelope, but catalogue C/C0 differ (305/340 kN vs 168/150 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-319-N2PHAS",
      "QJ 319 N2PHAS"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-220-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 220 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 180,
    "B_mm": 34,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 236,
    "static_load_kN": 265,
    "fatigue_load_limit_kN": 9.5,
    "limiting_speed_rpm": 6300,
    "max_rpm": 6300,
    "weight_g": 4050,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 220 N2MA is SKF's 100 mm-bore QJ four-point contact ball bearing of the QJ200 series, 100×180×34 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 100×180×34 mm (3.937×7.087×1.339 in), 40.0 mm radial section height, C 236 kN, C0 265 kN, Pu 9.5 kN.SKF publishes only the 6,300 r/min limiting speed for this execution, catalogue mass 4050 g. Sizing arithmetic on the 100 mm bore: 236 kN C divided by the 40.0 mm radial section height gives 5.9 kN per section millimetre; the 4050 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 9.5 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 236/265 kN ratings and 4050 g mass this execution carries about 2.36 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 6,300 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-220-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-220-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 220 N2MA as the qj slotted execution; the other order numbers of the QJ 220 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-220-N2MA?",
        "a": "QJ 220 N2MA measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 4050 g. SKF 17000 ratings: C 236 kN, C0 265 kN, Pu 9.5 kN, SKF publishes only the 6,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 220 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7220-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (236/265 kN vs 135/122 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (236/265 kN vs 143/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (236/265 kN vs 143/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×180×34 mm envelope, but catalogue C/C0 differ between executions (236/265 kN vs 143/134 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7220",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7220 BEP shares the 100×180×34 mm angular-contact envelope, but catalogue C/C0 differ (236/265 kN vs 135/122 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-220-N2MA",
      "QJ 220 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-320-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 320 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 100,
    "D_mm": 215,
    "B_mm": 47,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 345,
    "static_load_kN": 400,
    "fatigue_load_limit_kN": 13.7,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 9300,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 320 N2MA is SKF's 100 mm-bore QJ four-point contact ball bearing of the QJ300 series, 100×215×47 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 345 kN, C0 400 kN, Pu 13.7 kN.SKF publishes only the 5,600 r/min limiting speed for this execution, catalogue mass 9300 g. At the printed limiting speed of 5,600 r/min the mean pitch diameter dm ≈ 157.5 mm implies a dn value around 882k mm·r/min; only the limiting speed is published for this execution. The 13.7 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 345/400 kN ratings and 9300 g mass this execution carries about 3.45 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 5,600 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy gearbox locating positions",
      "screw conveyor and extruder thrust positions",
      "crane travel and hoist drives"
    ],
    "failure_modes": [
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-320-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-320-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 320 N2MA as the qj slotted execution; the other order numbers of the QJ 320 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-320-N2MA?",
        "a": "QJ 320 N2MA measures 100 mm bore × 215 mm OD × 47 mm width (3.937 × 8.465 × 1.85 in), mass about 9300 g. SKF 17000 ratings: C 345 kN, C0 400 kN, Pu 13.7 kN, SKF publishes only the 5,600 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-320-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7320-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (345/400 kN vs 203/190 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (345/400 kN vs 203/190 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (345/400 kN vs 216/208 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (345/400 kN vs 216/208 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 100×215×47 mm envelope, but catalogue C/C0 differ between executions (345/400 kN vs 216/208 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7320",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7320 BEP shares the 100×215×47 mm angular-contact envelope, but catalogue C/C0 differ (345/400 kN vs 203/190 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-320-N2MA",
      "QJ 320 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-222-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 222 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 200,
    "B_mm": 38,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 280,
    "static_load_kN": 325,
    "fatigue_load_limit_kN": 11.2,
    "limiting_speed_rpm": 5600,
    "max_rpm": 5600,
    "weight_g": 5600,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 222 N2MA is SKF's 110 mm-bore QJ four-point contact ball bearing of the QJ200 series, 110×200×38 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 110×200×38 mm (4.331×7.874×1.496 in), 45.0 mm radial section height, C 280 kN, C0 325 kN, Pu 11.2 kN.SKF publishes only the 5,600 r/min limiting speed for this execution, catalogue mass 5600 g. Mass and section check: 5600 g inside the 110×200×38 mm outline leaves a 45.0 mm radial section, and the 325 kN static rating is 1.16× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 325 kN against C 280 kN gives a 1.16 ratio, typical of a four-point thrust-oriented design; Pu 11.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 200 over bore 110 is a 1.82× step for this size, and the 38 mm width gives a bore/width ratio of 2.89; use these ratios when housing space around the 110 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Anti-rotation is built into QJ-222-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-222-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 222 N2MA as the qj slotted execution; the other order numbers of the QJ 222 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-222-N2MA?",
        "a": "QJ 222 N2MA measures 110 mm bore × 200 mm OD × 38 mm width (4.331 × 7.874 × 1.496 in), mass about 5600 g. SKF 17000 ratings: C 280 kN, C0 325 kN, Pu 11.2 kN, SKF publishes only the 5,600 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-222-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7222-BEP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (280/325 kN vs 153/143 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (280/325 kN vs 163/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (280/325 kN vs 163/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×200×38 mm envelope, but catalogue C/C0 differ between executions (280/325 kN vs 163/156 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7222",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7222 BEP shares the 110×200×38 mm angular-contact envelope, but catalogue C/C0 differ (280/325 kN vs 153/143 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-222-N2MA",
      "QJ 222 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-322-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 322 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 110,
    "D_mm": 240,
    "B_mm": 50,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 390,
    "static_load_kN": 480,
    "fatigue_load_limit_kN": 15.3,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 12500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 322 N2MA is SKF's 110 mm-bore QJ four-point contact ball bearing of the QJ300 series, 110×240×50 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 110×240×50 mm (4.331×9.449×1.969 in), 65.0 mm radial section height, C 390 kN, C0 480 kN, Pu 15.3 kN.SKF publishes only the 4,800 r/min limiting speed for this execution, catalogue mass 12500 g. Selection figures for QJ 322 N2MA: the static-to-dynamic ratio C0/C is 1.23, Pu 15.3 kN is about 4 % of C, and catalogue mass works out to roughly 114 g per millimetre of bore. Load balance: C0 480 kN against C 390 kN gives a 1.23 ratio, typical of a four-point thrust-oriented design; Pu 15.3 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 240 over bore 110 is a 2.18× step for this size, and the 50 mm width gives a bore/width ratio of 2.20; use these ratios when housing space around the 110 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "turret and slewing drives",
      "paper-machine calender stacks",
      "heavy gearbox locating positions"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-322-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-322-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 322 N2MA as the qj slotted execution; the other order numbers of the QJ 322 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-322-N2MA?",
        "a": "QJ 322 N2MA measures 110 mm bore × 240 mm OD × 50 mm width (4.331 × 9.449 × 1.969 in), mass about 12500 g. SKF 17000 ratings: C 390 kN, C0 480 kN, Pu 15.3 kN, SKF publishes only the 4,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 322 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7322-BEY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (390/480 kN vs 225/224 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322-BEM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (390/480 kN vs 225/224 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322-BECBP",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (390/480 kN vs 240/245 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322-BECBY",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (390/480 kN vs 240/245 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322-BECBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 110×240×50 mm envelope, but catalogue C/C0 differ between executions (390/480 kN vs 240/245 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7322",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "SKF SKF 7322 BECBP shares the 110×240×50 mm angular-contact envelope, but catalogue C/C0 differ (390/480 kN vs 240/245 kN) — envelope match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-322-N2MA",
      "QJ 322 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-224-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 224 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 215,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 300,
    "static_load_kN": 365,
    "fatigue_load_limit_kN": 12,
    "limiting_speed_rpm": 5000,
    "max_rpm": 5000,
    "weight_g": 6950,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 224 N2MA is SKF's 120 mm-bore QJ four-point contact ball bearing of the QJ200 series, 120×215×40 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 120×215×40 mm (4.724×8.465×1.575 in), 47.5 mm radial section height, C 300 kN, C0 365 kN, Pu 12 kN.SKF publishes only the 5,000 r/min limiting speed for this execution, catalogue mass 6950 g. The 12 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 300/365 kN ratings and 6950 g mass this execution carries about 2.50 kN of C per millimetre of bore. Sizing arithmetic on the 120 mm bore: 300 kN C divided by the 47.5 mm radial section height gives 6.3 kN per section millimetre; the 6950 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 5,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is built into QJ-224-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-224-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 224 N2MA as the qj slotted execution; the other order numbers of the QJ 224 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-224-N2MA?",
        "a": "QJ 224 N2MA measures 120 mm bore × 215 mm OD × 40 mm width (4.724 × 8.465 × 1.575 in), mass about 6950 g. SKF 17000 ratings: C 300 kN, C0 365 kN, Pu 12 kN, SKF publishes only the 5,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 224 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7224-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope, but catalogue C/C0 differ between executions (300/365 kN vs 165/163 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7224-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×215×40 mm envelope, but catalogue C/C0 differ between executions (300/365 kN vs 165/163 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-224-N2MA",
      "QJ 224 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-324-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 324 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 120,
    "D_mm": 260,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 415,
    "static_load_kN": 530,
    "fatigue_load_limit_kN": 16.3,
    "limiting_speed_rpm": 4500,
    "max_rpm": 4500,
    "weight_g": 16000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 324 N2MA is SKF's 120 mm-bore QJ four-point contact ball bearing of the QJ300 series, 120×260×55 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 120×260×55 mm (4.724×10.236×2.165 in), 70.0 mm radial section height, C 415 kN, C0 530 kN, Pu 16.3 kN.SKF publishes only the 4,500 r/min limiting speed for this execution, catalogue mass 16000 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,500 r/min and no separate thermal reference is published; at dm ≈ 190.0 mm the corresponding dn is approximately 855k mm·r/min. Sizing arithmetic on the 120 mm bore: 415 kN C divided by the 70.0 mm radial section height gives 5.9 kN per section millimetre; the 16000 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,500 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-324-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-324-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 324 N2MA as the qj slotted execution; the other order numbers of the QJ 324 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-324-N2MA?",
        "a": "QJ 324 N2MA measures 120 mm bore × 260 mm OD × 55 mm width (4.724 × 10.236 × 2.165 in), mass about 16000 g. SKF 17000 ratings: C 415 kN, C0 530 kN, Pu 16.3 kN, SKF publishes only the 4,500 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-324-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7324-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 120×260×55 mm envelope, but catalogue C/C0 differ between executions (415/530 kN vs 238/250 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-324-N2MA",
      "QJ 324 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-226-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 226 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 230,
    "B_mm": 40,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 310,
    "static_load_kN": 400,
    "fatigue_load_limit_kN": 12.7,
    "limiting_speed_rpm": 4800,
    "max_rpm": 4800,
    "weight_g": 7750,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 226 N2MA is SKF's 130 mm-bore QJ four-point contact ball bearing of the QJ200 series, 130×230×40 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 130×230×40 mm (5.118×9.055×1.575 in), 50.0 mm radial section height, C 310 kN, C0 400 kN, Pu 12.7 kN.SKF publishes only the 4,800 r/min limiting speed for this execution, catalogue mass 7750 g. Load balance: C0 400 kN against C 310 kN gives a 1.29 ratio, typical of a four-point thrust-oriented design; Pu 12.7 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 7750 g inside the 130×230×40 mm outline leaves a 50.0 mm radial section, and the 400 kN static rating is 1.29× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 230 over bore 130 is a 1.77× step for this size, and the 40 mm width gives a bore/width ratio of 3.25; use these ratios when housing space around the 130 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-226-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-226-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 226 N2MA as the qj slotted execution; the other order numbers of the QJ 226 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-226-N2MA?",
        "a": "QJ 226 N2MA measures 130 mm bore × 230 mm OD × 40 mm width (5.118 × 9.055 × 1.575 in), mass about 7750 g. SKF 17000 ratings: C 310 kN, C0 400 kN, Pu 12.7 kN, SKF publishes only the 4,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-226-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7226-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope, but catalogue C/C0 differ between executions (310/400 kN vs 186/193 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7226-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×230×40 mm envelope, but catalogue C/C0 differ between executions (310/400 kN vs 186/193 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-226-N2MA",
      "QJ 226 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-326-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 326 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 130,
    "D_mm": 280,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 455,
    "static_load_kN": 610,
    "fatigue_load_limit_kN": 18,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 19500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 326 N2MA is SKF's 130 mm-bore QJ four-point contact ball bearing of the QJ300 series, 130×280×58 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 130×280×58 mm (5.118×11.024×2.283 in), 75.0 mm radial section height, C 455 kN, C0 610 kN, Pu 18 kN.SKF publishes only the 4,000 r/min limiting speed for this execution, catalogue mass 19500 g. Envelope economics: the 58 mm width over a 75.0 mm section yields 0.77 mm of ring width per section millimetre, and the bearing weighs 19500 g for 455 kN of dynamic capacity — about 43 g per rated kN. Mass and section check: 19500 g inside the 130×280×58 mm outline leaves a 75.0 mm radial section, and the 610 kN static rating is 1.34× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Bore-to-OD planning: OD 280 over bore 130 is a 2.15× step for this size, and the 58 mm width gives a bore/width ratio of 2.24; use these ratios when housing space around the 130 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms",
      "offshore winch and swivel drives"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-326-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-326-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 326 N2MA as the qj slotted execution; the other order numbers of the QJ 326 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-326-N2MA?",
        "a": "QJ 326 N2MA measures 130 mm bore × 280 mm OD × 58 mm width (5.118 × 11.024 × 2.283 in), mass about 19500 g. SKF 17000 ratings: C 455 kN, C0 610 kN, Pu 18 kN, SKF publishes only the 4,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 326 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7326-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×280×58 mm envelope, but catalogue C/C0 differ between executions (455/610 kN vs 276/305 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7326-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 130×280×58 mm envelope, but catalogue C/C0 differ between executions (455/610 kN vs 276/305 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-326-N2MA",
      "QJ 326 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-228-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 228 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 250,
    "B_mm": 42,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 345,
    "static_load_kN": 475,
    "fatigue_load_limit_kN": 14.3,
    "limiting_speed_rpm": 4300,
    "max_rpm": 4300,
    "weight_g": 9850,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 228 N2MA is SKF's 140 mm-bore QJ four-point contact ball bearing of the QJ200 series, 140×250×42 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 140×250×42 mm (5.512×9.843×1.654 in), 55.0 mm radial section height, C 345 kN, C0 475 kN, Pu 14.3 kN.SKF publishes only the 4,300 r/min limiting speed for this execution, catalogue mass 9850 g. Sizing arithmetic on the 140 mm bore: 345 kN C divided by the 55.0 mm radial section height gives 6.3 kN per section millimetre; the 9850 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 14.3 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 345/475 kN ratings and 9850 g mass this execution carries about 2.46 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,300 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "offshore winch and swivel drives",
      "heavy converter tilt drives",
      "large gearbox thrust locations paired with cylindrical roller radial bearings"
    ],
    "failure_modes": [
      "outer-ring creep and seat fretting where a N2-locating-slot bearing is not positively stopped",
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-228-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-228-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 228 N2MA as the qj slotted execution; the other order numbers of the QJ 228 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-228-N2MA?",
        "a": "QJ 228 N2MA measures 140 mm bore × 250 mm OD × 42 mm width (5.512 × 9.843 × 1.654 in), mass about 9850 g. SKF 17000 ratings: C 345 kN, C0 475 kN, Pu 14.3 kN, SKF publishes only the 4,300 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 228 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7228-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope, but catalogue C/C0 differ between executions (345/475 kN vs 199/212 kN) — boundary dimensions match, not a load-rating equivalent."
      },
      {
        "equiv_sku": "7228-BM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×250×42 mm envelope, but catalogue C/C0 differ between executions (345/475 kN vs 199/212 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-228-N2MA",
      "QJ 228 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-328-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 328 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 140,
    "D_mm": 300,
    "B_mm": 62,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 500,
    "static_load_kN": 695,
    "fatigue_load_limit_kN": 20,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 24000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 328 N2MA is SKF's 140 mm-bore QJ four-point contact ball bearing of the QJ300 series, 140×300×62 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 140×300×62 mm (5.512×11.811×2.441 in), 80.0 mm radial section height, C 500 kN, C0 695 kN, Pu 20 kN.SKF publishes only the 3,800 r/min limiting speed for this execution, catalogue mass 24000 g. At the printed limiting speed of 3,800 r/min the mean pitch diameter dm ≈ 220.0 mm implies a dn value around 836k mm·r/min; only the limiting speed is published for this execution. The 20 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 500/695 kN ratings and 24000 g mass this execution carries about 3.57 kN of C per millimetre of bore. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 3,800 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy converter tilt drives",
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-328-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-328-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 328 N2MA as the qj slotted execution; the other order numbers of the QJ 328 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-328-N2MA?",
        "a": "QJ 328 N2MA measures 140 mm bore × 300 mm OD × 62 mm width (5.512 × 11.811 × 2.441 in), mass about 24000 g. SKF 17000 ratings: C 500 kN, C0 695 kN, Pu 20 kN, SKF publishes only the 3,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-328-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7328-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 140×300×62 mm envelope, but catalogue C/C0 differ between executions (500/695 kN vs 302/345 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-328-N2MA",
      "QJ 328 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-230-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 230 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 270,
    "B_mm": 45,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 400,
    "static_load_kN": 570,
    "fatigue_load_limit_kN": 16.6,
    "limiting_speed_rpm": 4000,
    "max_rpm": 4000,
    "weight_g": 12500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 230 N2MA is SKF's 150 mm-bore QJ four-point contact ball bearing of the QJ200 series, 150×270×45 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 150×270×45 mm (5.906×10.63×1.772 in), 60.0 mm radial section height, C 400 kN, C0 570 kN, Pu 16.6 kN.SKF publishes only the 4,000 r/min limiting speed for this execution, catalogue mass 12500 g. Envelope economics: the 45 mm width over a 60.0 mm section yields 0.75 mm of ring width per section millimetre, and the bearing weighs 12500 g for 400 kN of dynamic capacity — about 31 g per rated kN. Mass and section check: 12500 g inside the 150×270×45 mm outline leaves a 60.0 mm radial section, and the 570 kN static rating is 1.43× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 4,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-230-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-230-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 230 N2MA as the qj slotted execution; the other order numbers of the QJ 230 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-230-N2MA?",
        "a": "QJ 230 N2MA measures 150 mm bore × 270 mm OD × 45 mm width (5.906 × 10.63 × 1.772 in), mass about 12500 g. SKF 17000 ratings: C 400 kN, C0 570 kN, Pu 16.6 kN, SKF publishes only the 4,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 230 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7230-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×270×45 mm envelope, but catalogue C/C0 differ between executions (400/570 kN vs 216/240 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-230-N2MA",
      "QJ 230 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-330-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 330 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 150,
    "D_mm": 320,
    "B_mm": 65,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 530,
    "static_load_kN": 765,
    "fatigue_load_limit_kN": 21.2,
    "limiting_speed_rpm": 3600,
    "max_rpm": 3600,
    "weight_g": 29000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 330 N2MA is SKF's 150 mm-bore QJ four-point contact ball bearing of the QJ300 series, 150×320×65 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 150×320×65 mm (5.906×12.598×2.559 in), 85.0 mm radial section height, C 530 kN, C0 765 kN, Pu 21.2 kN.SKF publishes only the 3,600 r/min limiting speed for this execution, catalogue mass 29000 g. Mass and section check: 29000 g inside the 150×320×65 mm outline leaves a 85.0 mm radial section, and the 765 kN static rating is 1.44× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 765 kN against C 530 kN gives a 1.44 ratio, typical of a four-point thrust-oriented design; Pu 21.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 3,600 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "rolling-mill adjustment mechanisms",
      "offshore winch and swivel drives",
      "heavy converter tilt drives"
    ],
    "failure_modes": [
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-330-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-330-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 330 N2MA as the qj slotted execution; the other order numbers of the QJ 330 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-330-N2MA?",
        "a": "QJ 330 N2MA measures 150 mm bore × 320 mm OD × 65 mm width (5.906 × 12.598 × 2.559 in), mass about 29000 g. SKF 17000 ratings: C 530 kN, C0 765 kN, Pu 21.2 kN, SKF publishes only the 3,600 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-330-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7330-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 150×320×65 mm envelope, but catalogue C/C0 differ between executions (530/765 kN vs 332/390 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-330-N2MA",
      "QJ 330 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-232-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 232 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 290,
    "B_mm": 48,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 450,
    "static_load_kN": 670,
    "fatigue_load_limit_kN": 19,
    "limiting_speed_rpm": 3800,
    "max_rpm": 3800,
    "weight_g": 15500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 232 N2MA is SKF's 160 mm-bore QJ four-point contact ball bearing of the QJ200 series, 160×290×48 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 160×290×48 mm (6.299×11.417×1.89 in), 65.0 mm radial section height, C 450 kN, C0 670 kN, Pu 19 kN.SKF publishes only the 3,800 r/min limiting speed for this execution, catalogue mass 15500 g. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,800 r/min and no separate thermal reference is published; at dm ≈ 225.0 mm the corresponding dn is approximately 855k mm·r/min. Sizing arithmetic on the 160 mm bore: 450 kN C divided by the 65.0 mm radial section height gives 6.9 kN per section millimetre; the 15500 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 290 over bore 160 is a 1.81× step for this size, and the 48 mm width gives a bore/width ratio of 3.33; use these ratios when housing space around the 160 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms",
      "offshore winch and swivel drives"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "mounting score marks when the bearing is cocked over a burr or keyway",
      "mounting score marks when the bearing is cocked over a burr or keyway"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-232-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-232-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 232 N2MA as the qj slotted execution; the other order numbers of the QJ 232 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-232-N2MA?",
        "a": "QJ 232 N2MA measures 160 mm bore × 290 mm OD × 48 mm width (6.299 × 11.417 × 1.89 in), mass about 15500 g. SKF 17000 ratings: C 450 kN, C0 670 kN, Pu 19 kN, SKF publishes only the 3,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-232-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7232-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 160×290×48 mm envelope, but catalogue C/C0 differ between executions (450/670 kN vs 255/300 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-232-N2MA",
      "QJ 232 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-332-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 332 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 160,
    "D_mm": 340,
    "B_mm": 68,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 570,
    "static_load_kN": 880,
    "fatigue_load_limit_kN": 23.6,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 34500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 332 N2MA is SKF's 160 mm-bore QJ four-point contact ball bearing of the QJ300 series, 160×340×68 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 160×340×68 mm (6.299×13.386×2.677 in), 90.0 mm radial section height, C 570 kN, C0 880 kN, Pu 23.6 kN.SKF publishes only the 3,400 r/min limiting speed for this execution, catalogue mass 34500 g. Sizing arithmetic on the 160 mm bore: 570 kN C divided by the 90.0 mm radial section height gives 6.3 kN per section millimetre; the 34500 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. The 23.6 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 570/880 kN ratings and 34500 g mass this execution carries about 3.56 kN of C per millimetre of bore. Bore-to-OD planning: OD 340 over bore 160 is a 2.13× step for this size, and the 68 mm width gives a bore/width ratio of 2.35; use these ratios when housing space around the 160 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms",
      "offshore winch and swivel drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "fretting corrosion on a loose rotating shaft seat",
      "electrical pitting on VFD-driven shafts without grounding protection"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Anti-rotation is built into QJ-332-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-332-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 332 N2MA as the qj slotted execution; the other order numbers of the QJ 332 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-332-N2MA?",
        "a": "QJ 332 N2MA measures 160 mm bore × 340 mm OD × 68 mm width (6.299 × 13.386 × 2.677 in), mass about 34500 g. SKF 17000 ratings: C 570 kN, C0 880 kN, Pu 23.6 kN, SKF publishes only the 3,400 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 332 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "QJ",
        "equiv_brand": "ISO 15",
        "level": "full",
        "note": "ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-332-N2MA",
      "QJ 332 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-234-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 234 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 310,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 455,
    "static_load_kN": 720,
    "fatigue_load_limit_kN": 20,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 19500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 234 N2MA is SKF's 170 mm-bore QJ four-point contact ball bearing of the QJ200 series, 170×310×52 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 170×310×52 mm (6.693×12.205×2.047 in), 70.0 mm radial section height, C 455 kN, C0 720 kN, Pu 20 kN.SKF publishes only the 3,400 r/min limiting speed for this execution, catalogue mass 19500 g. Selection figures for QJ 234 N2MA: the static-to-dynamic ratio C0/C is 1.58, Pu 20 kN is about 4 % of C, and catalogue mass works out to roughly 115 g per millimetre of bore. Load balance: C0 720 kN against C 455 kN gives a 1.58 ratio, typical of a four-point thrust-oriented design; Pu 20 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 3,400 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy converter tilt drives",
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "brinelling from pressing the ring home through the balls or from static overload",
      "brinelling from pressing the ring home through the balls or from static overload"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Anti-rotation is built into QJ-234-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-234-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 234 N2MA as the qj slotted execution; the other order numbers of the QJ 234 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-234-N2MA?",
        "a": "QJ 234 N2MA measures 170 mm bore × 310 mm OD × 52 mm width (6.693 × 12.205 × 2.047 in), mass about 19500 g. SKF 17000 ratings: C 455 kN, C0 720 kN, Pu 20 kN, SKF publishes only the 3,400 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 234 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7234-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×310×52 mm envelope, but catalogue C/C0 differ between executions (455/720 kN vs 281/345 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-234-N2MA",
      "QJ 234 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-334-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 334 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 170,
    "D_mm": 360,
    "B_mm": 72,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 655,
    "static_load_kN": 1040,
    "fatigue_load_limit_kN": 27,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 41500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 334 N2MA is SKF's 170 mm-bore QJ four-point contact ball bearing of the QJ300 series, 170×360×72 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 170×360×72 mm (6.693×14.173×2.835 in), 95.0 mm radial section height, C 655 kN, C0 1040 kN, Pu 27 kN.SKF publishes only the 3,200 r/min limiting speed for this execution, catalogue mass 41500 g. Load balance: C0 1040 kN against C 655 kN gives a 1.59 ratio, typical of a four-point thrust-oriented design; Pu 27 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 41500 g inside the 170×360×72 mm outline leaves a 95.0 mm radial section, and the 1040 kN static rating is 1.59× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 3,200 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms",
      "offshore winch and swivel drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Run the QJ as a thrust bearing with radial clearance in the housing, paired with a separate radial bearing; the QJ outer ring must not be radially clamped.",
      "Anti-rotation is built into QJ-334-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-334-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 334 N2MA as the qj slotted execution; the other order numbers of the QJ 334 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-334-N2MA?",
        "a": "QJ 334 N2MA measures 170 mm bore × 360 mm OD × 72 mm width (6.693 × 14.173 × 2.835 in), mass about 41500 g. SKF 17000 ratings: C 655 kN, C0 1040 kN, Pu 27 kN, SKF publishes only the 3,200 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-334-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7334-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 170×360×72 mm envelope, but catalogue C/C0 differ between executions (655/1040 kN vs 390/490 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-334-N2MA",
      "QJ 334 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-236-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 236 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 320,
    "B_mm": 52,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 475,
    "static_load_kN": 765,
    "fatigue_load_limit_kN": 20.8,
    "limiting_speed_rpm": 3400,
    "max_rpm": 3400,
    "weight_g": 20500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 236 N2MA is SKF's 180 mm-bore QJ four-point contact ball bearing of the QJ200 series, 180×320×52 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 180×320×52 mm (7.087×12.598×2.047 in), 70.0 mm radial section height, C 475 kN, C0 765 kN, Pu 20.8 kN.SKF publishes only the 3,400 r/min limiting speed for this execution, catalogue mass 20500 g. At the printed limiting speed of 3,400 r/min the mean pitch diameter dm ≈ 250.0 mm implies a dn value around 850k mm·r/min; only the limiting speed is published for this execution. The 20.8 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 475/765 kN ratings and 20500 g mass this execution carries about 2.64 kN of C per millimetre of bore. Bore-to-OD planning: OD 320 over bore 180 is a 1.78× step for this size, and the 52 mm width gives a bore/width ratio of 3.46; use these ratios when housing space around the 180 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms"
    ],
    "failure_modes": [
      "axial over-travel when the outer ring is clamped instead of left with radial clearance and a small end-play gap",
      "two-piece inner-ring separation damage if the split ring is pressed or heated unevenly during mounting",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "edge loading from shaft deflection or housing misalignment",
      "edge loading from shaft deflection or housing misalignment"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-236-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-236-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 236 N2MA as the qj slotted execution; the other order numbers of the QJ 236 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-236-N2MA?",
        "a": "QJ 236 N2MA measures 180 mm bore × 320 mm OD × 52 mm width (7.087 × 12.598 × 2.047 in), mass about 20500 g. SKF 17000 ratings: C 475 kN, C0 765 kN, Pu 20.8 kN, SKF publishes only the 3,400 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What minimum axial load does QJ-236-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7236-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×320×52 mm envelope, but catalogue C/C0 differ between executions (475/765 kN vs 291/375 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-236-N2MA",
      "QJ 236 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-336-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 336 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 180,
    "D_mm": 380,
    "B_mm": 75,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 680,
    "static_load_kN": 1100,
    "fatigue_load_limit_kN": 28,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 47500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 336 N2MA is SKF's 180 mm-bore QJ four-point contact ball bearing of the QJ300 series, 180×380×75 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 180×380×75 mm (7.087×14.961×2.953 in), 100.0 mm radial section height, C 680 kN, C0 1100 kN, Pu 28 kN.SKF publishes only the 3,000 r/min limiting speed for this execution, catalogue mass 47500 g. The 28 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 680/1100 kN ratings and 47500 g mass this execution carries about 3.78 kN of C per millimetre of bore. Sizing arithmetic on the 180 mm bore: 680 kN C divided by the 100.0 mm radial section height gives 6.8 kN per section millimetre; the 47500 g mass and 4 % Pu/C share frame the light-load floor for the adjusted-life check. Bore-to-OD planning: OD 380 over bore 180 is a 2.11× step for this size, and the 75 mm width gives a bore/width ratio of 2.40; use these ratios when housing space around the 180 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "offshore winch and swivel drives",
      "heavy converter tilt drives",
      "large gearbox thrust locations paired with cylindrical roller radial bearings"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "raceway staining from water in the lubricant during idle periods",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded"
    ],
    "pitfalls": [
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-336-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-336-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 336 N2MA as the qj slotted execution; the other order numbers of the QJ 336 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-336-N2MA?",
        "a": "QJ 336 N2MA measures 180 mm bore × 380 mm OD × 75 mm width (7.087 × 14.961 × 2.953 in), mass about 47500 g. SKF 17000 ratings: C 680 kN, C0 1100 kN, Pu 28 kN, SKF publishes only the 3,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "How is a QJ four-point bearing mounted?",
        "a": "As a thrust/locating bearing with radial clearance in the housing, paired with a separate radial bearing (commonly a cylindrical roller bearing): the QJ locates the shaft axially in both directions, the radial bearing carries radial load. Keep the outer ring unclamped with a small end-play gap; N2 slot executions use dogs to stop the outer ring turning."
      },
      {
        "q": "What does QJ mean in QJ 336 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7336-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 180×380×75 mm envelope, but catalogue C/C0 differ between executions (680/1100 kN vs 410/540 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-336-N2MA",
      "QJ 336 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-238-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 238 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 340,
    "B_mm": 55,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 510,
    "static_load_kN": 850,
    "fatigue_load_limit_kN": 22.4,
    "limiting_speed_rpm": 3200,
    "max_rpm": 3200,
    "weight_g": 23500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 238 N2MA is SKF's 190 mm-bore QJ four-point contact ball bearing of the QJ200 series, 190×340×55 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 190×340×55 mm (7.48×13.386×2.165 in), 75.0 mm radial section height, C 510 kN, C0 850 kN, Pu 22.4 kN.SKF publishes only the 3,200 r/min limiting speed for this execution, catalogue mass 23500 g. Envelope economics: the 55 mm width over a 75.0 mm section yields 0.73 mm of ring width per section millimetre, and the bearing weighs 23500 g for 510 kN of dynamic capacity — about 46 g per rated kN. Mass and section check: 23500 g inside the 190×340×55 mm outline leaves a 75.0 mm radial section, and the 850 kN static rating is 1.67× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 3,200 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "heavy converter tilt drives",
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions"
    ],
    "failure_modes": [
      "false brinelling while the shaft stands with pure radial load and no minimum axial load",
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil",
      "hard-particle indentation of the asymmetric raceway in unfiltered oil"
    ],
    "pitfalls": [
      "Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The MA machined brass cage is outer-ring-centred — inspect its guide clearance when servicing",
      "Anti-rotation is built into QJ-238-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-238-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 238 N2MA as the qj slotted execution; the other order numbers of the QJ 238 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-238-N2MA?",
        "a": "QJ 238 N2MA measures 190 mm bore × 340 mm OD × 55 mm width (7.48 × 13.386 × 2.165 in), mass about 23500 g. SKF 17000 ratings: C 510 kN, C0 850 kN, Pu 22.4 kN, SKF publishes only the 3,200 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What does QJ mean in QJ 238 N2MA?",
        "a": "QJ is SKF's four-point contact design: a two-piece inner ring and gothic-arch raceways so each ball contacts at four points, giving bidirectional axial location with limited radial capacity — it must see Fa/Fr ≥ 1,27 for correct ball contact."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7238-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×340×55 mm envelope, but catalogue C/C0 differ between executions (510/850 kN vs 307/405 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-238-N2MA",
      "QJ 238 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-338-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 338 N2MA",
    "series": "QJ300-series",
    "type": "angular_contact",
    "d_mm": 190,
    "D_mm": 400,
    "B_mm": 78,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 702,
    "static_load_kN": 1160,
    "fatigue_load_limit_kN": 28.5,
    "limiting_speed_rpm": 2800,
    "max_rpm": 2800,
    "weight_g": 49000,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 338 N2MA is SKF's 190 mm-bore QJ four-point contact ball bearing of the QJ300 series, 190×400×78 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 190×400×78 mm (7.48×15.748×3.071 in), 105.0 mm radial section height, C 702 kN, C0 1160 kN, Pu 28.5 kN.SKF publishes only the 2,800 r/min limiting speed for this execution, catalogue mass 49000 g. Mass and section check: 49000 g inside the 190×400×78 mm outline leaves a 105.0 mm radial section, and the 1160 kN static rating is 1.65× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Load balance: C0 1160 kN against C 702 kN gives a 1.65 ratio, typical of a four-point thrust-oriented design; Pu 28.5 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 2,800 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "large gearbox thrust locations paired with cylindrical roller radial bearings",
      "marine transmission thrust positions",
      "rolling-mill adjustment mechanisms"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "rolling-contact fatigue spalling after the rated L10 life is exceeded",
      "fretting corrosion on a loose rotating shaft seat"
    ],
    "pitfalls": [
      "Keep a small axial gap between the outer ring and the cover flange so it can accommodate thermal movement; never clamp the outer ring solid.",
      "Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Anti-rotation is built into QJ-338-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-338-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 338 N2MA as the qj slotted execution; the other order numbers of the QJ 338 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-338-N2MA?",
        "a": "QJ 338 N2MA measures 190 mm bore × 400 mm OD × 78 mm width (7.48 × 15.748 × 3.071 in), mass about 49000 g. SKF 17000 ratings: C 702 kN, C0 1160 kN, Pu 28.5 kN, SKF publishes only the 2,800 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-338-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7338-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 190×400×78 mm envelope, but catalogue C/C0 differ between executions (702/1160 kN vs 442/600 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-338-N2MA",
      "QJ 338 N2MA"
    ],
    "locale_variants": {}
  },
  {
    "sku": "QJ-240-N2MA",
    "brand": "SKF",
    "manufacturer_designation": "QJ 240 N2MA",
    "series": "QJ200-series",
    "type": "angular_contact",
    "d_mm": 200,
    "D_mm": 360,
    "B_mm": 58,
    "material": "GCr15",
    "seal_type": "open",
    "clearance": "CN",
    "tolerance_class": "P0",
    "cage_type": "brass",
    "dynamic_load_kN": 540,
    "static_load_kN": 915,
    "fatigue_load_limit_kN": 23.2,
    "limiting_speed_rpm": 3000,
    "max_rpm": 3000,
    "weight_g": 28500,
    "weight_estimated": false,
    "temp_min_c": -40,
    "temp_max_c": 120,
    "standard": "ISO 15",
    "naming_rule_text": "QJ 240 N2MA is SKF's 200 mm-bore QJ four-point contact ball bearing of the QJ200 series, 200×360×58 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls. Envelope 200×360×58 mm (7.874×14.173×2.283 in), 80.0 mm radial section height, C 540 kN, C0 915 kN, Pu 23.2 kN.SKF publishes only the 3,000 r/min limiting speed for this execution, catalogue mass 28500 g. Load balance: C0 915 kN against C 540 kN gives a 1.69 ratio, typical of a four-point thrust-oriented design; Pu 23.2 kN enters the SKF adjusted-life equation rather than the basic rating life. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 3,000 r/min and no separate thermal reference is published; at dm ≈ 280.0 mm the corresponding dn is approximately 840k mm·r/min. Bore-to-OD planning: OD 360 over bore 200 is a 1.80× step for this size, and the 58 mm width gives a bore/width ratio of 3.45; use these ratios when housing space around the 200 mm shaft is the first constraint. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.",
    "applications": [
      "rolling-mill adjustment mechanisms",
      "offshore winch and swivel drives",
      "heavy converter tilt drives"
    ],
    "failure_modes": [
      "cage wear from speed above the limiting value with thin or aged lubricant",
      "ball skidding when the Fa/Fr 1,27 load-ratio condition is not met and the balls contact both sides of one raceway",
      "locating-slot root fretting or dog wear when only one N2 notch carries the anti-rotation torque",
      "electrical pitting on VFD-driven shafts without grounding protection",
      "raceway staining from water in the lubricant during idle periods"
    ],
    "pitfalls": [
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "The inner ring is two-piece: handle both halves together, mount square, and do not separate the split ring unless the fitting procedure requires it.",
      "Apply the Fa/Fr ≥ 1,27 condition: at lower ratios the balls contact both sides of a raceway, increasing friction and shortening life — the paired radial bearing should carry the radial share.",
      "Anti-rotation is built into QJ-240-N2MA: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.",
      "The MA brass cage of QJ-240-N2MA is outer-ring-centred: its guide land needs an uninterrupted oil film, so check lubricant reach when the bearing is used purely as a thrust location.",
      "Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 240 N2MA as the qj slotted execution; the other order numbers of the QJ 240 size are different products and may carry different ratings — always quote the full designation when purchasing."
    ],
    "faq": [
      {
        "q": "What are the dimensions and catalogue data of QJ-240-N2MA?",
        "a": "QJ 240 N2MA measures 200 mm bore × 360 mm OD × 58 mm width (7.874 × 14.173 × 2.283 in), mass about 28500 g. SKF 17000 ratings: C 540 kN, C0 915 kN, Pu 23.2 kN, SKF publishes only the 3,000 r/min limiting speed for this execution."
      },
      {
        "q": "What does the N2MA suffix mean?",
        "a": "QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. machined brass cage, outer-ring-centred (suffix MA), which guides on the outer ring rather than on the balls."
      },
      {
        "q": "What are the N2 locating slots for?",
        "a": "The two slots, 180° apart in one outer-ring side face, engage housing dogs or pins to prevent the radially loose outer ring from creeping and fretting its seat. The non-N2 execution relies on other anti-rotation measures."
      },
      {
        "q": "What minimum axial load does QJ-240-N2MA require?",
        "a": "Like angular-contact bearings the QJ needs a minimum axial load to keep the balls seated — spring preload against the outer ring is typical — and the load ratio Fa/Fr ≥ 1,27 keeps contact on one inner-ring raceway and the opposite outer-ring side."
      }
    ],
    "cross_ref": [
      {
        "equiv_sku": "7240-BCBM",
        "equiv_brand": "SKF",
        "level": "partial",
        "note": "Same 200×360×58 mm envelope, but catalogue C/C0 differ between executions (540/915 kN vs 325/430 kN) — boundary dimensions match, not a load-rating equivalent."
      }
    ],
    "source_ref": "https://cdn.skfmediahub.skf.com/api/public/0901d196802809de/pdf_preview_medium/0901d196802809de_pdf_preview_medium.pdf",
    "catalog_ver": "SKF PUB BU/P1 17000/1 EN (Oct 2018)",
    "extracted_at": "2026-09-27",
    "last_verified": "2026-09-27",
    "confidence_score": 0.7,
    "status": "published",
    "aliases": [
      "QJ-240-N2MA",
      "QJ 240 N2MA"
    ],
    "locale_variants": {}
  }
]
