240×440×120 mm bearings

10 models from 2 brands across 2 types share this ISO 15 envelope: 240 mm bore, 440 mm outside diameter, 120 mm width (9.449×17.323×4.724 in), 100 mm radial section.

10 models fit this space 2 brands 10 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22248EMD1 Spherical Roller NTN open CN 2470 3110 82600
22248EMKD1 Spherical Roller NTN open CN 2470 3110 80900
N2248 Cylindrical Roller NTN open CN 1590 2320 78400
NJ2248 Cylindrical Roller NTN open CN 1590 2320 78400
NJ2248-MA Cylindrical Roller SKF open CN 1450 2360 86000
NU2248 Cylindrical Roller NTN open CN 1590 2320 78400
NU2248-MA Cylindrical Roller SKF open CN 1450 2360 84000
NUH2248-ECMH Cylindrical Roller SKF open CN 1980 3050 80000
NUH2248-ECMH-PEX Cylindrical Roller SKF open CN 2279 3050 80000
NUP2248 Cylindrical Roller NTN open CN 1590 2320 78400

Note: catalogue dynamic load ratings for this envelope span 1450.0– 2470.0 kN — a 70% spread between designs in the very same 240×440×120 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 240 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22248EMD1, 22248EMKD1, N2248, NJ2248, NJ2248-MA, NU2248, NU2248-MA, NUH2248-ECMH, NUH2248-ECMH-PEX, NUP2248.

Frequently asked questions

Are all 240×440×120 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 240 mm bore, 440 mm OD, 120 mm width (9.449×17.323×4.724 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 10 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 240×440×120?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 240×440×120 mm in inches?

240×440×120 mm converts to 9.449×17.323×4.724 in, with a 100 mm (3.937 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22248EMD1, 22248EMKD1, N2248 mount in the same space despite different internal designs.