220×400×108 mm bearings

15 models from 2 brands across 3 types share this ISO 15 envelope: 220 mm bore, 400 mm outside diameter, 108 mm width (8.661×15.748×4.252 in), 90 mm radial section.

15 models fit this space 2 brands 15 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22244EMD1 Spherical Roller NTN open CN 2210 2690 59600
22244EMKD1 Spherical Roller NTN open CN 2210 2690 58400
C2244 CARB Toroidal Roller SKF open CN 2000 2500 57500
C2244-K CARB Toroidal Roller SKF open CN 2000 2500 57500
N2244 Cylindrical Roller NTN open CN 1260 1810 57800
NCF2244-ECJB Cylindrical Roller SKF open CN 1760 2600 58500
NCF2244-ECJB-PEX Cylindrical Roller SKF open CN 2000 2600 58500
NCF2244-V Cylindrical Roller SKF open CN 1830 2750 58000
NJ2244 Cylindrical Roller NTN open CN 1260 1810 57800
NJ2244-ECML Cylindrical Roller SKF open CN 1570 2280 60000
NU2244 Cylindrical Roller NTN open CN 1260 1810 57800
NU2244-ECML Cylindrical Roller SKF open CN 1570 2280 58000
NUH2244-ECMH Cylindrical Roller SKF open CN 1760 2600 59000
NUH2244-ECMH-PEX Cylindrical Roller SKF open CN 2000 2600 59000
NUP2244 Cylindrical Roller NTN open CN 1260 1810 57800

Note: catalogue dynamic load ratings for this envelope span 1260.0– 2210.0 kN — a 75% spread between designs in the very same 220×400×108 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 220 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22244EMD1, 22244EMKD1, C2244, C2244-K, N2244, NCF2244-ECJB, NCF2244-ECJB-PEX, NCF2244-V, NJ2244, NJ2244-ECML, NU2244, NU2244-ECML, NUH2244-ECMH, NUH2244-ECMH-PEX, NUP2244.

Frequently asked questions

Are all 220×400×108 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 220 mm bore, 400 mm OD, 108 mm width (8.661×15.748×4.252 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 15 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 220×400×108?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 220×400×108 mm in inches?

220×400×108 mm converts to 8.661×15.748×4.252 in, with a 90 mm (3.543 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22244EMD1, 22244EMKD1, C2244 mount in the same space despite different internal designs.