200×420×80 mm bearings

12 models from 3 brands across 3 types share this ISO 15 envelope: 200 mm bore, 420 mm outside diameter, 80 mm width (7.874×16.535×3.150 in), 110 mm radial section.

12 models fit this space 3 brands 12 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6340 Deep Groove Ball NSK open CN 415 445 55300
6340-NTN Deep Groove Ball NTN open CN 455 500 46300
7340 Angular Contact Ball NTN open CN 500 610 53100
7340-BCBM Angular Contact Ball SKF open CN 462 655 53000
7340B Angular Contact Ball NTN open CN 455 555 53100
N340 Cylindrical Roller NTN open CN 1080 1270 54500
NF340 Cylindrical Roller NTN open CN 1080 1270 54500
NJ340 Cylindrical Roller NTN open CN 1080 1270 54500
NJ340-ECML Cylindrical Roller SKF open CN 1230 1630 56500
NU340 Cylindrical Roller NTN open CN 1080 1270 54500
NU340-ECML Cylindrical Roller SKF open CN 1230 1630 57000
NUP340 Cylindrical Roller NTN open CN 1080 1270 54500

Note: catalogue dynamic load ratings for this envelope span 415.0– 1230.0 kN — a 196% spread between designs in the very same 200×420×80 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 200 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6340, 6340-NTN, 7340, 7340-BCBM, 7340B, N340, NF340, NJ340, NJ340-ECML, NU340, NU340-ECML, NUP340.

Frequently asked questions

Are all 200×420×80 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 200 mm bore, 420 mm OD, 80 mm width (7.874×16.535×3.150 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 12 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 200×420×80?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 200×420×80 mm in inches?

200×420×80 mm converts to 7.874×16.535×3.150 in, with a 110 mm (4.331 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6340, 6340-NTN, 7340 mount in the same space despite different internal designs.