200×360×98 mm bearings

14 models from 3 brands across 2 types share this ISO 15 envelope: 200 mm bore, 360 mm outside diameter, 98 mm width (7.874×14.173×3.858 in), 80 mm radial section.

14 models fit this space 3 brands 14 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22240EMD1 Spherical Roller NTN open CN 1810 2100 42700
22240EMKD1 Spherical Roller NTN open CN 1810 2100 41800
N2240 Cylindrical Roller NTN open CN 1020 1440 40500
NCF2240-ECJB Cylindrical Roller SKF open CN 1460 2000 43000
NJ2240 Cylindrical Roller NTN open CN 1020 1440 40500
NJ2240-ECML Cylindrical Roller SKF open CN 1370 1800 44000
NJ2240E Cylindrical Roller NTN open CN 1350 1870 —
NU2240 Cylindrical Roller NTN open CN 1020 1440 40500
NU2240-ECML Cylindrical Roller SKF open CN 1370 1800 44000
NU2240E Cylindrical Roller NTN open CN 1350 1870 —
NUH2240-ECMH Cylindrical Roller SKF open CN 1460 2000 43500
NUP2240 Cylindrical Roller NTN open CN 1020 1440 40500
NUP2240E Cylindrical Roller NTN open CN 1350 1870 —
SL182240 Cylindrical Roller FAG open CN 1410 2010 43120

Note: catalogue dynamic load ratings for this envelope span 1020.0– 1810.0 kN — a 77% spread between designs in the very same 200×360×98 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 200 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22240EMD1, 22240EMKD1, N2240, NCF2240-ECJB, NJ2240, NJ2240-ECML, NJ2240E, NU2240, NU2240-ECML, NU2240E, NUH2240-ECMH, NUP2240, NUP2240E, SL182240.

Frequently asked questions

Are all 200×360×98 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 200 mm bore, 360 mm OD, 98 mm width (7.874×14.173×3.858 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 14 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 200×360×98?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 200×360×98 mm in inches?

200×360×98 mm converts to 7.874×14.173×3.858 in, with a 80 mm (3.150 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22240EMD1, 22240EMKD1, N2240 mount in the same space despite different internal designs.