190×340×92 mm bearings

17 models from 3 brands across 3 types share this ISO 15 envelope: 190 mm bore, 340 mm outside diameter, 92 mm width (7.480×13.386×3.622 in), 75 mm radial section.

17 models fit this space 3 brands 17 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22238EMD1 Spherical Roller NTN open CN 1620 1870 35600
22238EMKD1 Spherical Roller NTN open CN 1620 1870 34900
C2238 CARB Toroidal Roller SKF open CN 1370 1730 34500
C2238-K CARB Toroidal Roller SKF open CN 1370 1730 34500
N2238 Cylindrical Roller NTN open CN 920 1290 33700
NCF2238-ECJB Cylindrical Roller SKF open CN 1320 1760 36500
NCF2238-V Cylindrical Roller SKF open CN 1250 1900 35500
NJ2238 Cylindrical Roller NTN open CN 920 1290 33700
NJ2238-ECML Cylindrical Roller SKF open CN 1220 1600 37000
NJ2238E Cylindrical Roller NTN open CN 1220 1670 —
NU2238 Cylindrical Roller NTN open CN 920 1290 33700
NU2238-ECML Cylindrical Roller SKF open CN 1220 1600 35500
NU2238E Cylindrical Roller NTN open CN 1220 1670 —
NUH2238-ECMH Cylindrical Roller SKF open CN 1320 1760 36000
NUP2238 Cylindrical Roller NTN open CN 920 1290 33700
NUP2238E Cylindrical Roller NTN open CN 1220 1670 —
SL182238 Cylindrical Roller FAG open CN 1300 1900 35650

Note: catalogue dynamic load ratings for this envelope span 920.0– 1620.0 kN — a 76% spread between designs in the very same 190×340×92 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 190 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22238EMD1, 22238EMKD1, C2238, C2238-K, N2238, NCF2238-ECJB, NCF2238-V, NJ2238, NJ2238-ECML, NJ2238E, NU2238, NU2238-ECML, NU2238E, NUH2238-ECMH, NUP2238, NUP2238E, SL182238.

Frequently asked questions

Are all 190×340×92 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 190 mm bore, 340 mm OD, 92 mm width (7.480×13.386×3.622 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 17 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 190×340×92?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 190×340×92 mm in inches?

190×340×92 mm converts to 7.480×13.386×3.622 in, with a 75 mm (2.953 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22238EMD1, 22238EMKD1, C2238 mount in the same space despite different internal designs.