190×340×55 mm bearings

20 models from 3 brands across 3 types share this ISO 15 envelope: 190 mm bore, 340 mm outside diameter, 55 mm width (7.480×13.386×2.165 in), 75 mm radial section.

20 models fit this space 3 brands 20 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6238 Deep Groove Ball SKF open CN 255 280 19500
6238-M Deep Groove Ball SKF open CN 255 280 21500
6238-NSK Deep Groove Ball NSK open CN 280 282 22300
6238-NTN Deep Groove Ball NTN open CN 282 281 18200
6238-ZZ Deep Groove Ball NSK ZZ CN 280 282 22300
7238 Angular Contact Ball NTN open CN 335 390 21300
7238-BCBM Angular Contact Ball SKF open CN 307 405 22000
7238B Angular Contact Ball NTN open CN 300 355 21300
N238 Cylindrical Roller NTN open CN 615 770 20800
NF238 Cylindrical Roller NTN open CN 615 770 20800
NJ238 Cylindrical Roller NTN open CN 615 770 20800
NJ238-ECML Cylindrical Roller SKF open CN 800 965 22000
NJ238E Cylindrical Roller NTN open CN 770 955 —
NU238 Cylindrical Roller NTN open CN 615 770 20800
NU238-ECML Cylindrical Roller SKF open CN 800 965 22500
NU238E Cylindrical Roller NTN open CN 770 955 —
NUP238 Cylindrical Roller NTN open CN 615 770 20800
NUP238-ECML Cylindrical Roller SKF open CN 800 965 22500
NUP238E Cylindrical Roller NTN open CN 770 955 —
QJ-238-N2MA Angular Contact Ball SKF open CN 510 850 23500

Note: catalogue dynamic load ratings for this envelope span 255.0– 800.0 kN — a 214% spread between designs in the very same 190×340×55 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 190 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6238, 6238-M, 6238-NSK, 6238-NTN, 6238-ZZ, 7238, 7238-BCBM, 7238B, N238, NF238, NJ238, NJ238-ECML, NJ238E, NU238, NU238-ECML, NU238E, NUP238, NUP238-ECML, NUP238E, QJ-238-N2MA.

Frequently asked questions

Are all 190×340×55 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 190 mm bore, 340 mm OD, 55 mm width (7.480×13.386×2.165 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 20 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 190×340×55?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 190×340×55 mm in inches?

190×340×55 mm converts to 7.480×13.386×2.165 in, with a 75 mm (2.953 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6238, 6238-M, 6238-NSK mount in the same space despite different internal designs.