180×320×52 mm bearings

19 models from 3 brands across 3 types share this ISO 15 envelope: 180 mm bore, 320 mm outside diameter, 52 mm width (7.087×12.598×2.047 in), 70 mm radial section.

19 models fit this space 3 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6236 Deep Groove Ball SKF open CN 229 240 16000
6236-M Deep Groove Ball SKF open CN 229 240 18000
6236-NSK Deep Groove Ball NSK open CN 250 241 15900
6236-NTN Deep Groove Ball NTN open CN 252 241 15100
6236-ZZ Deep Groove Ball NSK ZZ CN 250 241 15900
7236 Angular Contact Ball NTN open CN 340 385 17700
7236-BCBM Angular Contact Ball SKF open CN 291 375 18000
7236B Angular Contact Ball NTN open CN 305 350 17700
N236 Cylindrical Roller NTN open CN 550 675 17300
NF236 Cylindrical Roller NTN open CN 550 675 17300
NJ236 Cylindrical Roller NTN open CN 550 675 17300
NJ236-ECML Cylindrical Roller SKF open CN 720 850 18500
NJ236E Cylindrical Roller NTN open CN 695 850 —
NU236 Cylindrical Roller NTN open CN 550 675 17300
NU236-ECML Cylindrical Roller SKF open CN 720 850 18500
NU236E Cylindrical Roller NTN open CN 695 850 —
NUP236 Cylindrical Roller NTN open CN 550 675 17300
NUP236E Cylindrical Roller NTN open CN 695 850 —
QJ-236-N2MA Angular Contact Ball SKF open CN 475 765 20500

Note: catalogue dynamic load ratings for this envelope span 229.0– 720.0 kN — a 214% spread between designs in the very same 180×320×52 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 180 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6236, 6236-M, 6236-NSK, 6236-NTN, 6236-ZZ, 7236, 7236-BCBM, 7236B, N236, NF236, NJ236, NJ236-ECML, NJ236E, NU236, NU236-ECML, NU236E, NUP236, NUP236E, QJ-236-N2MA.

Frequently asked questions

Are all 180×320×52 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 180 mm bore, 320 mm OD, 52 mm width (7.087×12.598×2.047 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 19 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 180×320×52?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 180×320×52 mm in inches?

180×320×52 mm converts to 7.087×12.598×2.047 in, with a 70 mm (2.756 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6236, 6236-M, 6236-NSK mount in the same space despite different internal designs.