170×230×60 mm bearings

8 models from 3 brands across 1 type share this ISO 15 envelope: 170 mm bore, 230 mm outside diameter, 60 mm width (6.693×9.055×2.362 in), 30 mm radial section.

8 models fit this space 3 brands 8 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
NN4934 Cylindrical Roller NTN open CN 400 765 6560
NN4934K Cylindrical Roller NTN open CN 400 765 6240
NNC4934-CV Cylindrical Roller SKF open CN 457 950 7350
NNCF4934-CV Cylindrical Roller SKF open CN 457 950 7200
NNCL4934-CV Cylindrical Roller SKF open CN 457 950 7100
NNU4934K Cylindrical Roller NTN open CN 400 765 6550
SL014934 Cylindrical Roller FAG open CN 435 930 7350
SL024934 Cylindrical Roller FAG open CN 435 930 7100

Note: catalogue dynamic load ratings for this envelope span 400.0– 457.0 kN — a 14% spread between designs in the very same 170×230×60 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 170 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: NN4934, NN4934K, NNC4934-CV, NNCF4934-CV, NNCL4934-CV, NNU4934K, SL014934, SL024934.

Frequently asked questions

Are all 170×230×60 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 170 mm bore, 230 mm OD, 60 mm width (6.693×9.055×2.362 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 8 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 170×230×60?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 170×230×60 mm in inches?

170×230×60 mm converts to 6.693×9.055×2.362 in, with a 30 mm (1.181 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as NN4934, NN4934K, NNC4934-CV mount in the same space despite different internal designs.