150×320×108 mm bearings

17 models from 3 brands across 2 types share this ISO 15 envelope: 150 mm bore, 320 mm outside diameter, 108 mm width (5.906×12.598×4.252 in), 85 mm radial section.

17 models fit this space 3 brands 17 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22330 Spherical Roller SKF open CN 1539 1760 43500
22330-CCK-W33 Spherical Roller SKF open CN 1539 1760 47500
22330EMD1 Spherical Roller NTN open CN 1740 1890 42200
22330EMKD1 Spherical Roller NTN open CN 1740 1890 41300
N2330 Cylindrical Roller NTN open CN 1130 1400 39800
NCF2330-ECJB Cylindrical Roller SKF open CN 1430 1760 43500
NJ2330 Cylindrical Roller NTN open CN 1130 1400 39800
NJ2330-ECML Cylindrical Roller SKF open CN 1370 1630 43000
NJ2330E Cylindrical Roller NTN open CN 1290 1600 —
NJG2330-VH Cylindrical Roller SKF open CN 1450 1930 42500
NU2330 Cylindrical Roller NTN open CN 1130 1400 39800
NU2330-ECML Cylindrical Roller SKF open CN 1370 1630 42500
NU2330E Cylindrical Roller NTN open CN 1290 1600 —
NUH2330-ECMH Cylindrical Roller SKF open CN 1430 1760 42000
NUP2330 Cylindrical Roller NTN open CN 1130 1400 39800
NUP2330E Cylindrical Roller NTN open CN 1290 1600 —
SL192330-TB-BR Cylindrical Roller FAG open CN 1490 1900 42100

Note: catalogue dynamic load ratings for this envelope span 1130.0– 1740.0 kN — a 54% spread between designs in the very same 150×320×108 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 150 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22330, 22330-CCK-W33, 22330EMD1, 22330EMKD1, N2330, NCF2330-ECJB, NJ2330, NJ2330-ECML, NJ2330E, NJG2330-VH, NU2330, NU2330-ECML, NU2330E, NUH2330-ECMH, NUP2330, NUP2330E, SL192330-TB-BR.

Frequently asked questions

Are all 150×320×108 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 150 mm bore, 320 mm OD, 108 mm width (5.906×12.598×4.252 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 17 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 150×320×108?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 150×320×108 mm in inches?

150×320×108 mm converts to 5.906×12.598×4.252 in, with a 85 mm (3.346 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22330, 22330-CCK-W33, 22330EMD1 mount in the same space despite different internal designs.