150×270×73 mm bearings

21 models from 3 brands across 3 types share this ISO 15 envelope: 150 mm bore, 270 mm outside diameter, 73 mm width (5.906×10.630×2.874 in), 60 mm radial section.

21 models fit this space 3 brands 21 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22230 Spherical Roller SKF open CN 898 1080 18000
22230-CCK-W33 Spherical Roller SKF open CN 898 1080 23000
22230EAD1 Spherical Roller NTN open CN 1080 1220 17600
22230EAKD1 Spherical Roller NTN open CN 1080 1220 17300
22230EMD1 Spherical Roller NTN open CN 1080 1220 18000
22230EMKD1 Spherical Roller NTN open CN 1080 1220 17700
C2230 CARB Toroidal Roller SKF open CN 980 1220 18000
C2230-K CARB Toroidal Roller SKF open CN 980 1220 18000
N2230 Cylindrical Roller NTN open CN 555 710 16000
NCF2230-ECJB Cylindrical Roller SKF open CN 780 1040 18000
NCF2230-V Cylindrical Roller SKF open CN 781 1220 18500
NJ2230 Cylindrical Roller NTN open CN 555 710 16000
NJ2230-ECM Cylindrical Roller SKF open CN 735 930 19000
NJ2230E Cylindrical Roller NTN open CN 735 980 —
NU2230 Cylindrical Roller NTN open CN 555 710 16000
NU2230-ECM Cylindrical Roller SKF open CN 735 930 18500
NU2230E Cylindrical Roller NTN open CN 735 980 —
NUH2230-ECMH Cylindrical Roller SKF open CN 780 1040 18000
NUP2230 Cylindrical Roller NTN open CN 555 710 16000
NUP2230E Cylindrical Roller NTN open CN 735 980 —
SL182230 Cylindrical Roller FAG open CN 820 1160 18430

Note: catalogue dynamic load ratings for this envelope span 555.0– 1080.0 kN — a 95% spread between designs in the very same 150×270×73 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 150 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22230, 22230-CCK-W33, 22230EAD1, 22230EAKD1, 22230EMD1, 22230EMKD1, C2230, C2230-K, N2230, NCF2230-ECJB, NCF2230-V, NJ2230, NJ2230-ECM, NJ2230E, NU2230, NU2230-ECM, NU2230E, NUH2230-ECMH, NUP2230, NUP2230E, SL182230.

Frequently asked questions

Are all 150×270×73 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 150 mm bore, 270 mm OD, 73 mm width (5.906×10.630×2.874 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 21 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 150×270×73?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 150×270×73 mm in inches?

150×270×73 mm converts to 5.906×10.630×2.874 in, with a 60 mm (2.362 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22230, 22230-CCK-W33, 22230EAD1 mount in the same space despite different internal designs.