140×250×68 mm bearings

22 models from 3 brands across 3 types share this ISO 15 envelope: 140 mm bore, 250 mm outside diameter, 68 mm width (5.512×9.843×2.677 in), 55 mm radial section.

22 models fit this space 3 brands 22 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22228 Spherical Roller SKF open CN 743 900 14000
22228-CCK-W33 Spherical Roller SKF open CN 743 900 18000
22228EAD1 Spherical Roller NTN open CN 912 1010 13900
22228EAKD1 Spherical Roller NTN open CN 912 1010 13600
22228EMD1 Spherical Roller NTN open CN 912 1010 14200
22228EMKD1 Spherical Roller NTN open CN 912 1010 13900
C2228 CARB Toroidal Roller SKF open CN 830 1060 14000
C2228-K CARB Toroidal Roller SKF open CN 830 1060 14000
N2228 Cylindrical Roller NTN open CN 495 635 12600
NCF2228-ECJB Cylindrical Roller SKF open CN 680 880 14500
NCF2228-V Cylindrical Roller SKF open CN 693 1020 14500
NJ2228 Cylindrical Roller NTN open CN 495 635 12600
NJ2228-ECML Cylindrical Roller SKF open CN 655 830 15500
NJ2228E Cylindrical Roller NTN open CN 635 835 —
NU2228 Cylindrical Roller NTN open CN 495 635 12600
NU2228-ECML Cylindrical Roller SKF open CN 655 830 15000
NU2228E Cylindrical Roller NTN open CN 635 835 —
NUH2228-ECMH Cylindrical Roller SKF open CN 680 880 14500
NUP2228 Cylindrical Roller NTN open CN 495 635 12600
NUP2228-ECML Cylindrical Roller SKF open CN 655 830 15500
NUP2228E Cylindrical Roller NTN open CN 635 835 —
SL182228 Cylindrical Roller FAG open CN 720 1000 14470

Note: catalogue dynamic load ratings for this envelope span 495.0– 912.0 kN — a 84% spread between designs in the very same 140×250×68 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 140 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22228, 22228-CCK-W33, 22228EAD1, 22228EAKD1, 22228EMD1, 22228EMKD1, C2228, C2228-K, N2228, NCF2228-ECJB, NCF2228-V, NJ2228, NJ2228-ECML, NJ2228E, NU2228, NU2228-ECML, NU2228E, NUH2228-ECMH, NUP2228, NUP2228-ECML, NUP2228E, SL182228.

Frequently asked questions

Are all 140×250×68 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 140 mm bore, 250 mm OD, 68 mm width (5.512×9.843×2.677 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 22 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 140×250×68?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 140×250×68 mm in inches?

140×250×68 mm converts to 5.512×9.843×2.677 in, with a 55 mm (2.165 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22228, 22228-CCK-W33, 22228EAD1 mount in the same space despite different internal designs.