140×210×53 mm bearings

12 models from 3 brands across 3 types share this ISO 15 envelope: 140 mm bore, 210 mm outside diameter, 53 mm width (5.512×8.268×2.087 in), 35 mm radial section.

12 models fit this space 3 brands 12 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23028 Spherical Roller SKF open CN 485 680 6550
23028-CCK-W33 Spherical Roller SKF open CN 485 680 9400
23028EAD1 Spherical Roller NTN open CN 597 783 6320
23028EAKD1 Spherical Roller NTN open CN 597 783 6130
23028EMD1 Spherical Roller NTN open CN 597 783 6370
23028EMKD1 Spherical Roller NTN open CN 597 783 6180
323028 Tapered Roller NTN open CN 335 535 6360
413028 Tapered Roller NTN open CN 291 415 5730
NCF3028-CV Cylindrical Roller SKF open CN 440 680 6100
NN3028 Cylindrical Roller NTN open CN 330 515 6440
NN3028K Cylindrical Roller NTN open CN 330 515 6210
SL183028 Cylindrical Roller FAG open CN 450 660 6040

Note: catalogue dynamic load ratings for this envelope span 291.0– 597.0 kN — a 105% spread between designs in the very same 140×210×53 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 140 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23028, 23028-CCK-W33, 23028EAD1, 23028EAKD1, 23028EMD1, 23028EMKD1, 323028, 413028, NCF3028-CV, NN3028, NN3028K, SL183028.

Frequently asked questions

Are all 140×210×53 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 140 mm bore, 210 mm OD, 53 mm width (5.512×8.268×2.087 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 12 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 140×210×53?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 140×210×53 mm in inches?

140×210×53 mm converts to 5.512×8.268×2.087 in, with a 35 mm (1.378 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23028, 23028-CCK-W33, 23028EAD1 mount in the same space despite different internal designs.