120×260×86 mm bearings

19 models from 3 brands across 2 types share this ISO 15 envelope: 120 mm bore, 260 mm outside diameter, 86 mm width (4.724×10.236×3.386 in), 70 mm radial section.

19 models fit this space 3 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22324 Spherical Roller SKF open CN 1019 1120 23000
22324-CCK-W33 Spherical Roller SKF open CN 1019 1120 25500
22324EAD1 Spherical Roller NTN open CN 1170 1280 22300
22324EAKD1 Spherical Roller NTN open CN 1170 1280 21900
22324EMD1 Spherical Roller NTN open CN 1170 1280 22700
22324EMKD1 Spherical Roller NTN open CN 1170 1280 22200
N2324 Cylindrical Roller NTN open CN 785 920 21100
NJ2324 Cylindrical Roller NTN open CN 785 920 21100
NJ2324-ECML Cylindrical Roller SKF open CN 915 1040 23000
NJ2324E Cylindrical Roller NTN open CN 880 1030 —
NJG2324-VH Cylindrical Roller SKF open CN 952 1250 22500
NU2324 Cylindrical Roller NTN open CN 785 920 21100
NU2324-ECML Cylindrical Roller SKF open CN 915 1040 22500
NU2324E Cylindrical Roller NTN open CN 880 1030 —
NUH2324-ECMH Cylindrical Roller SKF open CN 965 1120 22500
NUP2324 Cylindrical Roller NTN open CN 785 920 21100
NUP2324-ECML Cylindrical Roller SKF open CN 915 1040 23500
NUP2324E Cylindrical Roller NTN open CN 880 1030 —
SL192324-TB-XL-BR Cylindrical Roller FAG open CN 1130 1230 22300

Note: catalogue dynamic load ratings for this envelope span 785.0– 1170.0 kN — a 49% spread between designs in the very same 120×260×86 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 120 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22324, 22324-CCK-W33, 22324EAD1, 22324EAKD1, 22324EMD1, 22324EMKD1, N2324, NJ2324, NJ2324-ECML, NJ2324E, NJG2324-VH, NU2324, NU2324-ECML, NU2324E, NUH2324-ECMH, NUP2324, NUP2324-ECML, NUP2324E, SL192324-TB-XL-BR.

Frequently asked questions

Are all 120×260×86 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 120 mm bore, 260 mm OD, 86 mm width (4.724×10.236×3.386 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 19 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 120×260×86?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 120×260×86 mm in inches?

120×260×86 mm converts to 4.724×10.236×3.386 in, with a 70 mm (2.756 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22324, 22324-CCK-W33, 22324EAD1 mount in the same space despite different internal designs.