120×215×58 mm bearings

19 models from 3 brands across 2 types share this ISO 15 envelope: 120 mm bore, 215 mm outside diameter, 58 mm width (4.724×8.465×2.283 in), 47.5 mm radial section.

19 models fit this space 3 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22224 Spherical Roller SKF open CN 652 765 8700
22224-EK Spherical Roller SKF open CN 652 765 11000
22224EAD1 Spherical Roller NTN open CN 688 753 8880
22224EAKD1 Spherical Roller NTN open CN 688 753 8680
22224EMD1 Spherical Roller NTN open CN 688 753 9010
22224EMKD1 Spherical Roller NTN open CN 688 753 8820
N2224 Cylindrical Roller NTN open CN 385 460 8030
NCF2224-V Cylindrical Roller SKF open CN 512 735 9050
NJ2224 Cylindrical Roller NTN open CN 385 460 8030
NJ2224-ECJ Cylindrical Roller SKF open CN 520 630 8650
NJ2224E Cylindrical Roller NTN open CN 500 620 —
NU2224 Cylindrical Roller NTN open CN 385 460 8030
NU2224-ECP Cylindrical Roller SKF open CN 520 630 8200
NU2224E Cylindrical Roller NTN open CN 500 620 —
NUH2224-ECMH Cylindrical Roller SKF open CN 550 670 9000
NUP2224 Cylindrical Roller NTN open CN 385 460 8030
NUP2224-ECP Cylindrical Roller SKF open CN 520 630 8650
NUP2224E Cylindrical Roller NTN open CN 500 620 —
SL182224 Cylindrical Roller FAG open CN 530 720 9080

Note: catalogue dynamic load ratings for this envelope span 385.0– 688.0 kN — a 79% spread between designs in the very same 120×215×58 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 120 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22224, 22224-EK, 22224EAD1, 22224EAKD1, 22224EMD1, 22224EMKD1, N2224, NCF2224-V, NJ2224, NJ2224-ECJ, NJ2224E, NU2224, NU2224-ECP, NU2224E, NUH2224-ECMH, NUP2224, NUP2224-ECP, NUP2224E, SL182224.

Frequently asked questions

Are all 120×215×58 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 120 mm bore, 215 mm OD, 58 mm width (4.724×8.465×2.283 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 19 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 120×215×58?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 120×215×58 mm in inches?

120×215×58 mm converts to 4.724×8.465×2.283 in, with a 47.5 mm (1.870 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22224, 22224-EK, 22224EAD1 mount in the same space despite different internal designs.