110×170×45 mm bearings

10 models from 3 brands across 2 types share this ISO 15 envelope: 110 mm bore, 170 mm outside diameter, 45 mm width (4.331×6.693×1.772 in), 30 mm radial section.

10 models fit this space 3 brands 10 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
23022 Spherical Roller SKF open CN 326 440 3800
23022-CCK-W33 Spherical Roller SKF open CN 326 440 5750
23022EAD1 Spherical Roller NTN open CN 417 517 3660
23022EAKD1 Spherical Roller NTN open CN 417 517 3550
23022EMD1 Spherical Roller NTN open CN 417 517 3660
23022EMKD1 Spherical Roller NTN open CN 417 517 3550
NCF3022-CV Cylindrical Roller SKF open CN 275 400 3500
NN3022 Cylindrical Roller NTN open CN 254 375 3690
NN3022K Cylindrical Roller NTN open CN 254 375 3560
SL183022 Cylindrical Roller FAG open CN 280 385 3500

Note: catalogue dynamic load ratings for this envelope span 254.0– 417.0 kN — a 64% spread between designs in the very same 110×170×45 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 110 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 23022, 23022-CCK-W33, 23022EAD1, 23022EAKD1, 23022EMD1, 23022EMKD1, NCF3022-CV, NN3022, NN3022K, SL183022.

Frequently asked questions

Are all 110×170×45 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 110 mm bore, 170 mm OD, 45 mm width (4.331×6.693×1.772 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 10 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 110×170×45?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 110×170×45 mm in inches?

110×170×45 mm converts to 4.331×6.693×1.772 in, with a 30 mm (1.181 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 23022, 23022-CCK-W33, 23022EAD1 mount in the same space despite different internal designs.