32206-DF bearing: complete specifications & equivalents

The 32206-DF is a ISO 355 radial bearing sized 30 x 62 x 42.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 62 mm d = 30 B = 42.5 mm side section front view
Principal dimensions: bore d 30 mm, outer diameter D 62 mm, width B 42.5 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 30 mm
Outer diameter D 62 mm
Width B 42.5 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 106 kN
Basic static load rating C0 116 kN
Fatigue load limit Pu 12.7 kN
Reference speed (thermal) 7500 rpm
Limiting speed (mechanical) 11000 rpm
Operating temperature -40 to +120 °C
Mass 590 g
Manufacturer designation SKF 32206/DF
Standard ISO 355
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants
Last verified 2026-09-29

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants) · extracted 2026-09-29

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & matched-df-series range

Bore d1.181 in
Outer diameter D2.441 in
Width B1.673 in
ISO bore code06
Radial section height (D−d)/216 mm
Smallest bore in matched-df-series25 mm
Largest outer diameter in matched-df-series540 mm
Width range across matched-df-series34.5–280 mm
Bore position in matched-df-series (smallest first)2 of 35
Bore above smallest matched-df-series size5 mm

Mounting, setting & life for 32206-DF

Fits & mounting

  • Tapered bearings are separable: press the cup square into the housing and fit the cone on the shaft — usually an interference fit on both seats in wheel/hub positions.
  • Mount the cone by induction heating (max 120 °C); never strike the cage or rollers directly.
  • Shaft and housing shoulders must clear the ring chamfers so the cone and cup seat fully against their faces.

Setting — the step deep-groove bearings never need

  • After seating, set the assembly to a defined end play or preload with the locknut/shim arrangement; locknut torque seats the parts — it is not the final adjustment.
  • General free-running positions: back the nut off while measuring with a dial indicator to a small end play (commonly around 0.05–0.15 mm for medium metric hubs — follow the OEM value).
  • Pinions and stiff arrangements run a controlled preload; too much preload is the classic cause of early spalling and heat.
  • Sealed factory-set units exist for specific designations — the open 32206-DF assumes the application sets and lubricates it.

Lubrication

Open TRBs are lubricated by the application. Fill the bearing with grease (typically around one third to one half of the free cavity — overpacking a TRB causes churning heat) and provide a relubrication path; intervals depend on contamination and temperature, not on catalogue rating alone.

Why the equivalent load matters more here

TRBs carry combined radial and axial loads, so the dynamic equivalent load P is computed with the bearing's e, X and Y factors for the actual thrust ratio — using the radial load alone over-estimates life badly.

Worked L10 life example (illustrative duty)

For roller bearings the life exponent is p = 10/3: L10h = (C/P)10/3 · 106 / (60·n). Taking an example equivalent load P = 21.2 kN (20% of C) at n = 1,500 r/min — substitute the real P from the X/Y calculation:

C = 106.0 kN → L10h ≈ 2,375 hours

Choosing a series at the same 30 mm bore

SeriesOpen executionOD × width TC (kN)C0 (kN)Limiting speed (r/min)
320xx3200655 × 1746.047.016,100
302xx3020662 × 17.2550.044.011,000
322xx3220662 × 21.2563.062.014,600
332xx3320662 × 2579.776.511,000
303xx30306CA72 × 20.7565.058.55,500
323xx32306C72 × 28.7588.094.05,500
313xx3130672 × 20.7558.350.09,500

Different series at the same bore are not drop-in swaps — OD, width and contact angle all change — and a cone number alone never identifies a complete set. Verify matches per the cross-reference levels guide; envelope variants are on the 30×62×42.5 envelope page.

Cross references & equivalents

Equivalent modelBrandMatch levelNote
32206 FAG verify
Commonly quoted cross reference; confirm against the target catalog before ordering.
Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue.
32206-NTN NTN verify
Commonly quoted cross reference; confirm against the target catalog before ordering.
Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 32206-DF model number is decoded

Load sharing in 32206-DF depends on spacer face parallelism; a cocked spacer concentrates the reversing thrust on one bearing of the pair and shows up as asymmetric raceway wear at overhaul. Clamp the assembled pair axially through the cones — never through the rollers — and verify the 42.5 mm overall width against the catalogue value before final torquing of the shaft nut.The SKF 32206/DF is a 30×62×42.5 mm matched tapered-roller set — two single-row bearings in face-to-face (X) matched pair arrangement, ground and shipped together with the axial clearance fixed at the factory.The code breaks down as base bearing 32206 plus matched-set suffix /DF: two bearings of the 30 mm bore size, paired face-to-face (X) matched pair, with the 42.5 mm overall width spanning the whole arrangement. Face-to-face matching puts the small rib ends outward, so the pressure cones cross inside the pair; 32206-DF therefore runs cooler where the shaft expands axially, at the price of lower moment stiffness than an O-arrangement of the same 30 mm bore. With a pair mass of 590 g across the 30×62×42.5 mm envelope, the set replaces what would otherwise be two separate bearings plus spacer grinding work — the factory setting is the engineering value being purchased. Dimensional interchange map: within its boundary plan the 30×62×42.5 mm envelope of 32206-DF is fixed, so shoulder, spacer and seal drawings can be dimensioned straight from the catalogue table.

Typical equipment & failure modes

Common applications

  • differential and pinion drives
  • pump and compressor shafts
  • machine-tool spindles
  • belt-driven fan and blower shafts

Known failure patterns

  • thermal preload runaway in an O-arrangement pair when inner-ring heat expands the setting
  • roller large-end smearing against the cone rib after EP lubricant film failure
  • cage pocket scoring when the bearing starts cold with grease of too-high base-oil viscosity
  • fretting corrosion on a loose rotating shaft seat
  • rib-roller contact scoring from loss of the EP additive film

Selection pitfalls — read before you substitute

  • Clamp the 32206-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
  • Setting is built into 32206-DF; the classic field error is re-adjusting a matched pair as if it were two loose single bearings, which destroys the /DF clearance class.
  • Clamp the 32206-DF pair axially through the cones, never through the rollers; pressing force across the roller complement brinells the raceways of both bearings at once.
  • The 106/116 kN ratings are SKF catalogue 17000 values for this execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification.
  • Quote the full SKF 32206/DF designation when purchasing — base-number-only orders are ambiguous across executions and variants.

Frequently asked questions

What are the dimensions and catalogue data of 32206-DF?

The SKF 32206/DF is a matched pair of single-row tapered roller bearings in face-to-face (X) matched pair arrangement with 30 mm bore, 62 mm outer diameter and 42.5 mm overall width (1.181 × 2.441 × 1.673 in). From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 106 kN, C0 116 kN, fatigue load limit Pu 12.7 kN, reference speed 7,500 r/min, limiting speed 11,000 r/min, mass about 0.59 kg.

What does the /DF suffix on 32206-DF mean?

The base 32206 is the ISO 355 single-row bearing; the /DF suffix marks the matched-set execution — the arrangement (face-to-face (X)), the ground spacer and the factory-set axial clearance class. A matched set cannot be assembled from loose single bearings; quote the full designation when ordering.

Are the C and C0 ratings of 32206-DF for one bearing or the pair?

They are for the complete matched pair: C 106 kN dynamic and C0 116 kN static already include load sharing between the two bearings. Do not halve them for single-bearing checks, and do not compare them directly with the single-row 32206 table values.

Can 32206-DF be adjusted like two loose tapered bearings?

No — the axial clearance is set at the factory by selective spacer grinding. Mounting work is limited to clean seats, correct fits (k5 on a rotating 30 mm shaft) and axial clamping through the cones; re-setting in the field destroys the matched clearance class.

When should a face-to-face (X) matched set be chosen?

Choose the face-to-face (X) set where the shaft grows thermally or alignment is imperfect — the converging load lines tolerate deflection. It is the default choice for wheel hubs and general gearbox shafts at the 30 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 8.3-8.8 TRB variants on 2026-09-29. Read our editorial & correction policy.