32205-NTN bearing: complete specifications & equivalents

The 32205-NTN is a ISO 355 radial bearing sized 25 x 52 x 19.25 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 52 mm d = 25 B = 19.25 mm side section front view
Principal dimensions: bore d 25 mm, outer diameter D 52 mm, width B 19.25 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand NTN
Bore diameter d 25 mm
Outer diameter D 52 mm
Width B 19.25 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel
Basic dynamic load rating C 46.5 kN
Basic static load rating C0 47 kN
Limiting speed (mechanical) 7300 rpm
Operating temperature -40 to +120 °C
Mass 187 g
Manufacturer designation NTN 32205
Standard ISO 355
Catalog version NTN Ball and Roller Bearings CAT.No.2203E
Last verified 2026-10-01

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Dimensions in inches & 32200-series range

Bore d0.984 in
Outer diameter D2.047 in
Width B0.758 in
ISO bore code05
Radial section height (D−d)/213.5 mm
Smallest bore in 32200-series17 mm
Largest outer diameter in 32200-series580 mm
Width range across 32200-series17.25–159 mm
Bore position in 32200-series (smallest first)3 of 36
Bore above smallest 32200-series size8 mm

Mounting, setting & life for 32205-NTN

Fits & mounting

  • Tapered bearings are separable: press the cup square into the housing and fit the cone on the shaft — usually an interference fit on both seats in wheel/hub positions.
  • Mount the cone by induction heating (max 120 °C); never strike the cage or rollers directly.
  • Shaft and housing shoulders must clear the ring chamfers so the cone and cup seat fully against their faces.

Setting — the step deep-groove bearings never need

  • After seating, set the assembly to a defined end play or preload with the locknut/shim arrangement; locknut torque seats the parts — it is not the final adjustment.
  • General free-running positions: back the nut off while measuring with a dial indicator to a small end play (commonly around 0.05–0.15 mm for medium metric hubs — follow the OEM value).
  • Pinions and stiff arrangements run a controlled preload; too much preload is the classic cause of early spalling and heat.
  • Sealed factory-set units exist for specific designations — the open 32205-NTN assumes the application sets and lubricates it.

Lubrication

Open TRBs are lubricated by the application. Fill the bearing with grease (typically around one third to one half of the free cavity — overpacking a TRB causes churning heat) and provide a relubrication path; intervals depend on contamination and temperature, not on catalogue rating alone.

Why the equivalent load matters more here

TRBs carry combined radial and axial loads, so the dynamic equivalent load P is computed with the bearing's e, X and Y factors for the actual thrust ratio — using the radial load alone over-estimates life badly.

Worked L10 life example (illustrative duty)

For roller bearings the life exponent is p = 10/3: L10h = (C/P)10/3 · 106 / (60·n). Taking an example equivalent load P = 9.3 kN (20% of C) at n = 1,500 r/min — substitute the real P from the X/Y calculation:

C = 46.5 kN → L10h ≈ 2,375 hours

Choosing a series at the same 25 mm bore

SeriesOpen executionOD × width TC (kN)C0 (kN)Limiting speed (r/min)
320xx3200547 × 1531.534.018,900
302xx3020552 × 16.2538.133.513,000
322xx3220552 × 19.2547.545.017,500
332xx3320552 × 2257.956.013,000
303xx30305C62 × 18.2546.041.56,400
323xx3230562 × 25.2574.163.012,000
313xx3130562 × 18.2546.640.011,000

Different series at the same bore are not drop-in swaps — OD, width and contact angle all change — and a cone number alone never identifies a complete set. Verify matches per the cross-reference levels guide; envelope variants are on the 25×52×19.25 envelope page.

Cross references & equivalents

Equivalent modelBrandMatch levelNote
32205 FAG full
Dimensions and internal design equivalent — standard interchange.
Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier.
32205-SKF SKF full
Dimensions and internal design equivalent — standard interchange.
Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 32205-NTN model number is decoded

32205 is a metric single-row tapered roller bearing in the NTN 4T programme: a pressed-steel cage guides profiled rollers between a separable cone and cup on the 25×52 mm ISO 355 envelope, with 19.25 mm overall assembled width T. On the NTN nameplate the parts carry 4T plus the bare code, while 2203E orders 32205 by the metric ISO 355 number (ISO series abbreviation 2CD): 25 mm bore, 52 mm OD. NTN grades 4T metric bearings as open bearings without integral seals; at 25 mm bore the application supplies the seals and the grease fill or oil supply to the 2CD ISO 355 assembly. Speed planning uses both catalogue columns: grease 7,300 r/min is the cage/rib mechanical ceiling for 32205, oil 9,800 r/min is available with circulating oil — a 2,500 r/min margin at this size. When pairing 32205 with a second tapered bearing, keep the matched arrangement clean: a single stray grit particle between cup and housing changes preload faster than the adjustment range can correct.

Typical equipment & failure modes

Common applications

  • light-vehicle differential and pinion shafts
  • agricultural implement hubs and ground-tool drives
  • small gearbox input shafts with combined load
  • scooter and light-powersport wheel and gear positions

Known failure patterns

  • cone-raceway spalling at the large rib when preload is set too high for the lubricant film
  • smearing on the roller large ends and cone rib after a dry start with preload but no oil film
  • flaking on one cone only when a back-to-back / face-to-face pair is loaded unevenly by a bent shaft
  • cage damage from a mounting blow delivered through the roller complement instead of the ring face
  • indentation of the raceways by hard particles in unsealed open arrangements

Selection pitfalls — read before you substitute

  • At 25 mm bore the thin section and small rollers are adjustment-sensitive: a quarter-turn of the locknut moves end play by more than on large bearings, so set the 32205 pair with a dial indicator rather than by feel.
  • The heavy-section 32200 family at 25 mm bore (52×19.25 mm assembled) carries more capacity than the lighter 320/329 sections but generates more preload heat; confirm oil availability before running near the 9,800 r/min oil ceiling.
  • Open 32205 units have no seals: a wheel-hub or gearbox application needs external sealing or the 7,300 r/min grease figure is meaningless once water reaches the cone rib.
  • The U/UTG/X/C/CA/D suffix variants of a base number share the bore but not the article: ordering 32205 by size alone can deliver the wrong contact-angle execution for a pinion position.
  • The 13.5 mm section leaves little room for an oversized shaft fillet; check the mounting-chamfer table for 32205 or the ring will bottom out on the radius instead of the shoulder face.
  • The 46.5/47 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 32205 (ISO 355 2CD); internal geometry legitimately differs between manufacturers, so re-verify ratings, adjustment and suffix before substituting another make on a rated drive.

Frequently asked questions

What are the dimensions and catalogue ratings of NTN 32205?

32205 is a metric 4T tapered roller bearing to ISO 355: 25 mm bore, 52 mm outside diameter and 19.25 mm assembled width T (0.984 × 2.047 × 0.758 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 46.5 kN, C0 47 kN (2203E prints no Pu for this size), grease limiting speed 7,300 r/min, oil speed 9,800 r/min, mass about 187 g. It is an open, separable cone/cup bearing with a pressed-steel cage.

What does the 4T prefix mean on 32205?

4T is NTN's tapered roller bearing brand mark, stamped on the cone and cup in the factory. It identifies the NTN 4T programme and is not a dimension, so the catalogue and this page list the bare ISO 355 number (32205); the lower-case 4t- factory spelling of the code is retained among the search aliases.

How does the 32205 designation encode the 25 mm bore and what is 2CD?

last two digits 05 are the ISO bore code, ×5 = 25 mm (codes 00–03 use the 10/12/15/17 exception table). The 52 mm OD and 19.25 mm assembled T follow the ISO 355 dimension-series plan. 2CD is the maker-neutral ISO 355 abbreviation for this dimension series (the same code other manufacturers print); 4T is NTN's own brand mark.

Why does 32205 list two speeds, 7,300 and 9,800 r/min?

The lower figure, 7,300 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 32205 at 9,800 r/min because oil removes rib-contact heat better. Real limits still depend on preload, oil flow and cooling.

What does the suffix on 32205 mean?

It is the basic open 4T execution — steel cage, adjusted mounting, no seal or feature suffix. NTN uses U for the uprated design, UTG for ULTAGE large-bearing specs, X for the ISO boundary section, and C/CA/D/A for contact-angle or internal-design variants; all are separate order numbers.

Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.