29444-E bearing: complete specifications & equivalents

The 29444-E is a ISO 104 radial bearing sized 220 x 420 x 122 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 420 mm d = 220 B = 122 mm side section front view
Principal dimensions: bore d 220 mm, outer diameter D 420 mm, width B 122 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 220 mm
Outer diameter D 420 mm
Width B 122 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel
Basic dynamic load rating C 3350 kN
Basic static load rating C0 9650 kN
Fatigue load limit Pu 900 kN
Reference speed (thermal) 850 rpm
Limiting speed (mechanical) 1500 rpm
Operating temperature -40 to +120 °C
Mass 75000 g
Manufacturer designation 29444 E
Standard ISO 104
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 29400-series range

Bore d8.661 in
Outer diameter D16.535 in
Width B4.803 in
ISO bore code44
Radial section height (D−d)/2100 mm
Smallest bore in 29400-series60 mm
Largest outer diameter in 29400-series1770 mm
Width range across 29400-series42–426 mm
Bore position in 29400-series (smallest first)19 of 46
Bore above smallest 29400-series size160 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
29444 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.
29444 NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 220×420×122 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 29444-E model number is decoded

The heavy 294 series bearing 29444 E carries 3350 kN of thrust on barrel rollers whose contact angle also tolerates radial force up to a fraction of the applied thrust — the standard heavy-duty thrust bearing for 220 mm shafts. SKF suffixes on spherical roller thrust bearings describe cages: E the standard stamped steel window cage, EM the machined brass execution, EF the extra-large steel-cage design; 29444 E is the stamped steel E window cage. The contact geometry also accepts simultaneous radial load up to roughly 55 % of the simultaneous axial force; beyond that mix, add a separate radial bearing to the arrangement. One direction only: 29444 E cannot be reversed to take opposite thrust — mirror a second bearing for reversing shafts, and keep housing and shaft seats square within the ISO 104 tolerances. Large 294 bearings go on with induction heating (max 120 °C) and oil injection features on tapered seats; never strike the stamped steel E window cage, and fill the oil bath to the catalogue level before first start.

Typical equipment & failure modes

Common applications

  • paper machine calender and refiner discs with combined axial and radial force
  • crane hook assemblies where the hook block turns under full load
  • injection moulding machine and extruder screw thrust positions
  • vertical hydro generators and large vertical pump motors

Known failure patterns

  • cage wear from rollers being dragged through unloaded zones under fluctuating thrust
  • shaft-washer creep and fretting corrosion on a soft or undersized shaft shoulder
  • abrasive paste forming as dust bypasses the housing seals into the open washer set
  • electrical erosion of raceways on VFD-driven shafts without grounding or insulation
  • roller skidding and raceway glazing once the thrust falls below the catalogue minimum axial load (factor A)

Selection pitfalls — read before you substitute

  • At 220 mm bore, oil flow becomes the design variable: the 3350 kN rating assumes fresh oil at the contact, and a blocked feed groove halves real life.
  • The 3350/9650 kN figures assume the matching sphered seating washer is fitted where the catalogue calls for it; a flat housing seat removes the self-aligning function.
  • Minimum load factor A 8.8 dominates commissioning: start the oil flow and preload before rotation, especially on 294 bearings where an unloaded cold start smears the rollers.
  • Radial force beyond the permitted fraction of simultaneous thrust (about 0.55·F_a) overloads one side of the barrel-roller set — add a radial bearing instead of leaning on 29444 E.
  • E, EM and EF suffixes are cage designs for different size bands, not quality grades: substitute only within the same envelope and check the lubricant compatibility of the cage material.
  • The 3350/9650 kN ratings and 75000 g mass are SKF catalogue values transcribed from ch. 13.1 of PUB BU/P1 17000 (PDF table page 926); mounting data — the minimum axial load factor A — appears in the running text because the structured record carries the boundary envelope only.

Frequently asked questions

What do E, EM and EF mean on 29444 E?

They are cage designs for different size bands: E is the stamped steel window cage of the current design, EM the machined brass cage for heavy/slow sizes, EF the steel cage for extra-large bearings — not quality grades. This bearing carries the stamped steel E window cage.

Where is the 29444 E typically used?

Crane hook blocks, extruder and injection-moulding screws, vertical hydro generators, large gearbox thrust positions and heavy mill shafts — places with very high one-direction axial load plus shaft deflection.

What destroys a spherical roller thrust bearing?

Unloaded rotation below A 8.8 (roller smearing), interrupted oil supply on the large sizes, a missing sphered seating washer that removes alignment, and contamination. Limiting speed here is 1,500 r/min.

Which dimensions does the 29444 E have?

A 29444 E measures 220 mm bore × 420 mm outside diameter × 122 mm width (8.661 × 16.535 × 4.803 in). From SKF catalogue PUB BU/P1 17000: dynamic C 3350 kN, static C0 9650 kN, fatigue limit Pu 900 kN, reference speed 850 r/min, limiting speed 1,500 r/min, mass about 75000 g. Minimum axial load factor A 8.8 must be maintained in service.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings on 2026-09-27. Read our editorial & correction policy.