NKIB5907 bearing: complete specifications & equivalents
The NKIB5907 is a DIN 616 radial bearing sized 35 x 55 x 30 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 35 mm |
| Outer diameter D | 55 mm |
| Width B | 30 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 31.9 kN |
| Basic static load rating C0 | 54 kN |
| Fatigue load limit Pu | 6.7 kN |
| Reference speed (thermal) | 9500 rpm |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 250 g |
| Manufacturer designation | NKIB 5907 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NKIB-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 2.165 in |
| Width B | 1.181 in |
| ISO bore code | 07 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in NKIB-series | 12 mm |
| Largest outer diameter in NKIB-series | 100 mm |
| Width range across NKIB-series | 17.5–45 mm |
| Bore position in NKIB-series (smallest first) | 8 of 15 |
| Bore above smallest NKIB-series size | 23 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NKIB5907 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NKIB5907 model number is decoded
SKF lists NKIB 5907 among the combined needle roller / three-point contact ball bearings: radial capacity from the needle roller set (31.9 kN C), axial capacity from the three-point contact ball part 5.83 kN (Ca), all within a 55×30 mm outline. In SKF nomenclature NKIB denotes the combined construction and 595907 the series/bore; the ball raceway sits offset on the inner ring, which is why the 30 mm overall width is greater than a plain needle bearing of the same bore. The combined unit is greased for life at assembly in many applications; relubrication, where provided, must reach both the roller cage and the ball set through the same axial bore features. Speed ceilings differ by part: 9,500 r/min thermal reference and 11,000 r/min limiting — the thrust element governs, since its washer faces see sliding components of contact. Life-lubricated as supplied in most sizes; where a relubrication path exists, meter grease gently — pressure through the 30 mm wide unit can lift the seals of adjacent components.
Typical equipment & failure modes
Common applications
- gearbox main shafts carrying radial plus one-direction thrust
- worm gear shafts with axial reaction toward the worm
- spindle heads needing compact radial-plus-axial support
- lead-screw and ball-screw support positions
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- hard-particle indentation in unfiltered lubricant
- thrust washer raceway wear from reverse axial shocks the one-direction thrust part cannot carry
Selection pitfalls — read before you substitute
- At 35 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 35 mm seats can bend past the compensation range long before the load rating is exhausted.
- Reference and limiting speeds are different limits: the 9,500 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 35 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- Height stack-up is easy to mis-check: the ball-raceway part adds height beyond a plain needle bearing, and clamping the stack solid over it preloads the thrust set beyond its rating.
- Do not treat the axial rating 5.83 kN (Ca) as independent of radial load: the combined equivalent load formulas couple them, and a unit sized on radial life alone will spall the ball raceway first under real thrust.
- The 31.9/54 kN ratings and 250 g mass are SKF catalogue values transcribed from ch. 7.7 of PUB BU/P1 17000 (PDF table page 654); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Is the NKIB 5907 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Which dimensions does the NKIB 5907 have?
A NKIB 5907 measures 35 mm bore/Fw × 55 mm outside diameter × 30 mm width (1.378 × 2.165 × 1.181 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 31.9 kN, static C0 54 kN, fatigue limit Pu 6.7 kN, limiting speed 11,000 r/min, reference speed 9,500 r/min, mass about 250 g. Axial ratings of the ball part: dynamic Ca 5.83 kN (Ca), static C0a 8.42 kN (C0a); three-point contact geometry accepts axial load in both directions.
What does NKIB 5907 mean in SKF part numbering?
NKIB combines a needle roller cage with an three-point contact ball bearing in one unit; 595907 gives the series and 35 mm bore. The offset (s 27 mm) positions the ball raceway inside the 30 mm overall width.
Does the NKIB 5907 need a hardened and ground shaft?
The needle roller part of the NKIB 5907 rides directly on the 35 mm journal, so it must be hardened to 58–64 HRC and ground; the ball set runs on its own integrated raceways. There is no inner-ring variant — harden the shaft or move to a separate bearing arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings on 2026-09-26. Read our editorial & correction policy.