NKIB5901 bearing: complete specifications & equivalents
The NKIB5901 is a DIN 616 radial bearing sized 12 x 24 x 17.5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 12 mm |
| Outer diameter D | 24 mm |
| Width B | 17.5 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 8.09 kN |
| Basic static load rating C0 | 9.65 kN |
| Fatigue load limit Pu | 1.14 kN |
| Reference speed (thermal) | 22000 rpm |
| Limiting speed (mechanical) | 26000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 43 g |
| Manufacturer designation | NKIB 5901 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NKIB-series range
| Bore d | 0.472 in |
|---|---|
| Outer diameter D | 0.945 in |
| Width B | 0.689 in |
| ISO bore code | 01 |
| Radial section height (D−d)/2 | 6 mm |
| Smallest bore in NKIB-series | 12 mm |
| Largest outer diameter in NKIB-series | 100 mm |
| Width range across NKIB-series | 17.5–45 mm |
| Bore position in NKIB-series (smallest first) | 1 of 15 |
| Bore above smallest NKIB-series size | 0 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| NKIB5901 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the NKIB5901 model number is decoded
SKF lists NKIB 5901 among the combined needle roller / three-point contact ball bearings: radial capacity from the needle roller set (8.09 kN C), axial capacity from the three-point contact ball part 2.07 kN (Ca), all within a 24×17.5 mm outline. Reading the designation: the letters combine the needle roller family with the ball execution — NKIB marks three-point contact — and 595901 the heavy 59 dimension series around the 12 mm bore. The combined unit is greased for life at assembly in many applications; relubrication, where provided, must reach both the roller cage and the ball set through the same axial bore features. Speed ceilings differ by part: 22,000 r/min thermal reference and 26,000 r/min limiting — the thrust element governs, since its washer faces see sliding components of contact. Life-lubricated as supplied in most sizes; where a relubrication path exists, meter grease gently — pressure through the 17.5 mm wide unit can lift the seals of adjacent components.
Typical equipment & failure modes
Common applications
- gearbox main shafts carrying radial plus one-direction thrust
- worm gear shafts with axial reaction toward the worm
- spindle heads needing compact radial-plus-axial support
- lead-screw and ball-screw support positions
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- hard-particle indentation in unfiltered lubricant
- thrust washer raceway wear from reverse axial shocks the one-direction thrust part cannot carry
Selection pitfalls — read before you substitute
- On a 12 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 24 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Reference and limiting speeds are different limits: the 22,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- Hardness is load capacity: in families without an inner ring the 12 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The thrust part is one-direction: reverse axial events — however brief — lift the rolling elements off the raceway, and the subsequent re-entry impact dents the washer face; mount the NKIB 5901 facing the working thrust.
- Minimum axial load is a real requirement: below the catalogue minimum the thrust elements skid, polish their raceways and lose them — springs or preload washers belong in the arrangement drawing, not the troubleshooting notes.
- The 8.09/9.65 kN ratings and 43 g mass are SKF catalogue values transcribed from ch. 7.7 of PUB BU/P1 17000 (PDF table page 654); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Which dimensions does the NKIB 5901 have?
A NKIB 5901 measures 12 mm bore/Fw × 24 mm outside diameter × 17.5 mm width (0.472 × 0.945 × 0.689 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 8.09 kN, static C0 9.65 kN, fatigue limit Pu 1.14 kN, limiting speed 26,000 r/min, reference speed 22,000 r/min, mass about 43 g. Axial ratings of the ball part: dynamic Ca 2.07 kN (Ca), static C0a 1.92 kN (C0a); three-point contact geometry accepts axial load in both directions.
What does NKIB 5901 mean in SKF part numbering?
NKIB combines a needle roller cage with an three-point contact ball bearing in one unit; 595901 gives the series and 12 mm bore. The offset (s 16 mm) positions the ball raceway inside the 17.5 mm overall width.
Does the NKIB 5901 need a hardened and ground shaft?
The needle roller part of the NKIB 5901 rides directly on the 12 mm journal, so it must be hardened to 58–64 HRC and ground; the ball set runs on its own integrated raceways. There is no inner-ring variant — harden the shaft or move to a separate bearing arrangement.
What mounting mistakes ruin a NKIB 5901?
Press on the ring faces only with a fitting sleeve, keep everything square to the 12 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.7 needle roller / angular contact ball bearings on 2026-09-26. Read our editorial & correction policy.