NKI100-40 bearing: complete specifications & equivalents

The NKI100-40 is a DIN 616 radial bearing sized 100 x 130 x 40 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 130 mm d = 100 B = 40 mm side section front view
Principal dimensions: bore d 100 mm, outer diameter D 130 mm, width B 40 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 100 mm
Outer diameter D 130 mm
Width B 40 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage none
Basic dynamic load rating C 123 kN
Basic static load rating C0 305 kN
Fatigue load limit Pu 37.5 kN
Reference speed (thermal) 3600 rpm
Limiting speed (mechanical) 4000 rpm
Operating temperature -40 to +120 °C
Mass 1350 g
Manufacturer designation NKI 100/40
Standard DIN 616
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring
Last verified 2026-09-26

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring) · extracted 2026-09-26

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & NKI-series range

Bore d3.937 in
Outer diameter D5.118 in
Width B1.575 in
ISO bore code—
Radial section height (D−d)/215 mm
Smallest bore in NKI-series5 mm
Largest outer diameter in NKI-series130 mm
Width range across NKI-series12–40 mm
Bore position in NKI-series (smallest first)30 of 30
Bore above smallest NKI-series size95 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
NKI100-30-XL FAG verify
Commonly quoted cross reference; confirm against the target catalog before ordering.
Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue.
NKI100-40-XL FAG partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 100×130×40 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting.
NKI100 ISO 15 full
Dimensions and internal design equivalent — standard interchange.
ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the NKI100-40 model number is decoded

For a 100 mm shaft that cannot be hardened on site, NKI 100/40 adds a hardened, ground inner ring to the machined needle roller design: envelope 100×130×40 mm per the machined-ring needle roller bearings with inner ring plan. In SKF nomenclature the leading letters mark a machined-ring needle bearing with inner ring: figures state 100 mm d and 40 mm B, the 130 mm outside diameter from the machined-ring needle roller bearings with inner ring, and the 2RS suffix would add contact seals. Execution notes: the inner ring is ground on bore and raceway, so the shaft seat is a normal k5/j6; the flanged outer ring needs no housing shoulder, and NA 49 2RS executions add seals with a wider outer ring. The 1350 g catalogue mass and 15.0 mm radial section ((130−100)/2) frame a rating of about 1.23 kN dynamic per millimetre of bore — the needle construction's density advantage over ball bearings of the same envelope. Mounting: heat or press the inner ring onto the 100 mm k5 seat (max 120 °C), fit the flanged outer ring into the H7 housing bore, and check the 40 mm assembly for free rotation before applying load.

Typical equipment & failure modes

Common applications

  • conveyor roller ends and return rollers
  • agricultural implement pivots and cutter heads
  • electric motor armature shafts with ground seats
  • printing and paper-handling rollers

Known failure patterns

  • needle edge loading and raceway denting when the shaft deflects beyond the compensation range
  • polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
  • grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
  • corrosion pitting from condensation in intermittently operated machinery
  • inner-ring raceway spalling after the narrow ring section runs hot with excessive interference

Selection pitfalls — read before you substitute

  • Above 50 mm bore, thermal growth matters: the 100 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
  • The quoted 123/305 kN ratings are SKF catalogue values for this exact execution (NKI 100/40); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
  • Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
  • The 123/305 kN ratings and 1350 g mass are SKF catalogue values transcribed from ch. 7.4 of PUB BU/P1 17000 (PDF table page 646); combined-type axial ratings appear in the text above because the structured record carries radial values only.

Frequently asked questions

Does the NKI 100/40 need a hardened and ground shaft?

Yes — that is the point of this family. The NKI 100/40 carries its own hardened, ground inner ring on a 100 mm seat, so the shaft needs only a normal k5/j6 finish. The inner ring is separable and replaceable.

What mounting mistakes ruin a NKI 100/40?

Mount the inner ring on the 100 mm seat first (induction heat, max 120 °C, or press), then fit the flanged outer ring into the H7 housing bore. Verify free rotation and, for 2RS executions, check the wider outer ring against the housing depth.

Is the NKI 100/40 sealed?

No — the open execution relies on housing seals; 2RS executions of the 49 series add contact seals with a wider outer ring as a separate order number.

Which dimensions does the NKI 100/40 have?

A NKI 100/40 measures 100 mm bore/Fw × 130 mm outside diameter × 40 mm width (3.937 × 5.118 × 1.575 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 123 kN, static C0 305 kN, fatigue limit Pu 37.5 kN, limiting speed 4,000 r/min, reference speed 3,600 r/min, mass about 1350 g.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.4 machined rings with flanges, with an inner ring on 2026-09-26. Read our editorial & correction policy.