AXK85110 bearing: complete specifications & equivalents
The AXK85110 is a ISO 3031 radial bearing sized 85 x 110 x 4 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 85 mm |
| Outer diameter D | 110 mm |
| Width B | 4 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 52 kN |
| Basic static load rating C0 | 290 kN |
| Fatigue load limit Pu | 35.5 kN |
| Reference speed (thermal) | 1700 rpm |
| Limiting speed (mechanical) | 3400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 67 g |
| Manufacturer designation | AXK 85110 |
| Standard | ISO 3031 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & AXK-series range
| Bore d | 3.346 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 0.157 in |
| ISO bore code | 10 |
| Radial section height (D−d)/2 | 12.5 mm |
| Smallest bore in AXK-series | 4 mm |
| Largest outer diameter in AXK-series | 200 mm |
| Width range across AXK-series | 2–5 mm |
| Bore position in AXK-series (smallest first) | 22 of 30 |
| Bore above smallest AXK-series size | 81 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| AXK85110 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the AXK85110 model number is decoded
For transmission gears that would otherwise rub on a housing wall, AXK 85110 supplies a complete needle thrust track between 89 and 108 mm raceway diameters in a 4 mm envelope. Reading the code: AXK marks the needle thrust assembly and the figures 85/110 give the two raceway diameters in millimetres — 85 mm inner track and 110 mm outer track; TN swaps the stamped steel cage for PA66. At this size the stamped steel cage guides long thrust needles; the TN polymer-cage variant is offered where noise matters. One-direction thrust only. One direction only: AXK 85110 cannot be reversed to take opposite thrust — mirror a second bearing for reversing shafts, and keep housing and shaft seats square within the ISO 104 tolerances. Mounting: harden and grind both mating faces to 58–64 HRC over the full Ea 89–Eb 108 mm band (or fit AS/LS washers), drop the 4 mm cage in flat, and never press or hammer the needle complement.
Typical equipment & failure modes
Common applications
- compact drives where hardened washers replace a machined raceway shoulder
- automotive manual and automatic transmission thrust positions
- torque converter and clutch release assemblies in passenger cars
- small gearbox gears that need a 2 mm thrust shim between a shaft and face
Known failure patterns
- instant raceway scoring when the assembly runs against a face below 58 HRC or with a rough finish
- cage wear from rollers being dragged through unloaded zones under fluctuating thrust
- grease churning and overheating when a high-speed thrust position is over-packed
- rolling-contact fatigue spalling after the catalogue L10 life is exhausted
- edge loading across the needle crowns when the mating faces are not square to the shaft
Selection pitfalls — read before you substitute
- At 85 mm track diameter, face hardness decides everything: a ground-but-soft washer looks correct yet ribbons within months; specify 58–64 HRC on the drawing.
- The 52 kN rating is real only at 58–64 HRC face hardness; visual inspection cannot tell a 45 HRC washer from a 60 HRC one — order certified washers.
- Do not expect misalignment tolerance: a 4 mm rigid needle set edge-loads if the faces tilt even a fraction of a degree — use a spherical or AXW solution where the seat cannot be kept parallel.
- TN polymer and stamped steel cages of the same code (AXK 85110) share envelopes and ratings; the choice is temperature and noise, not load.
- The AXK code supplies no washers: AXK 85110 arrives as the needle cage only, and a "bearing failure" on hard-faced tracks is usually a missing-AS-washer failure at ordering time.
- The 52/290 kN ratings and 67 g mass are SKF catalogue values transcribed from ch. 12.1 of PUB BU/P1 17000 (PDF table page 908); mounting data — Ea/Eb raceway diameters and the minimum load factor A — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
Which dimensions does the AXK 85110 have?
A AXK 85110 measures 85 mm bore × 110 mm outside diameter × 4 mm width (3.346 × 4.331 × 0.157 in). From SKF catalogue PUB BU/P1 17000: dynamic C 52 kN, static C0 290 kN, fatigue limit Pu 35.5 kN, reference speed 1,700 r/min, limiting speed 3,400 r/min, mass about 67 g. The contact band runs Ea 89–Eb 108 mm; hardened washers or 58–64 HRC faces are required.
What does AXK 85/110 mean?
A needle roller and cage thrust assembly (ISO 3031) for a 85 mm inner track and 110 mm outer track, 4 mm thick; one-direction axial load, washers ordered separately.
What is the difference between AXK and AXW?
AXW pairs the AXK needle set with a washer carrying an integral centring spigot that locates in a housing register, keeping cage and washer concentric as one part; AXK is the bare cage-and-needle set needing two separate washers. The AXW still needs a separate LS/AS washer or hardened face on the opposite side.
Does the AXK 85110 tolerate misalignment?
No — the 4 mm rigid needle set edge-loads on tilted faces. Keep the shaft and housing faces parallel, or choose the self-aligning roller thrust families.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies on 2026-09-27. Read our editorial & correction policy.