AXK6085 bearing: complete specifications & equivalents
The AXK6085 is a ISO 3031 radial bearing sized 60 x 85 x 3 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 60 mm |
| Outer diameter D | 85 mm |
| Width B | 3 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 37.5 kN |
| Basic static load rating C0 | 232 kN |
| Fatigue load limit Pu | 28.5 kN |
| Reference speed (thermal) | 2200 rpm |
| Limiting speed (mechanical) | 4300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 33 g |
| Manufacturer designation | AXK 6085 |
| Standard | ISO 3031 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & AXK-series range
| Bore d | 2.362 in |
|---|---|
| Outer diameter D | 3.346 in |
| Width B | 0.118 in |
| ISO bore code | 85 |
| Radial section height (D−d)/2 | 12.5 mm |
| Smallest bore in AXK-series | 4 mm |
| Largest outer diameter in AXK-series | 200 mm |
| Width range across AXK-series | 2–5 mm |
| Bore position in AXK-series (smallest first) | 17 of 30 |
| Bore above smallest AXK-series size | 56 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| AXK6085 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the AXK6085 model number is decoded
For transmission gears that would otherwise rub on a housing wall, AXK 6085 supplies a complete needle thrust track between 65 and 83 mm raceway diameters in a 3 mm envelope. Reading the code: AXK marks the needle thrust assembly and the figures 60/85 give the two raceway diameters in millimetres — 60 mm inner track and 85 mm outer track; TN swaps the stamped steel cage for PA66. At this size the stamped steel cage guides long thrust needles; the TN polymer-cage variant is offered where noise matters. One-direction thrust only. The 33 g mass and 3 mm axial height sit between 60 and 85 mm washer diameters; check the seat shoulder spans the full ring face — a narrow shoulder causes washer fretting long before fatigue does. Mounting: harden and grind both mating faces to 58–64 HRC over the full Ea 65–Eb 83 mm band (or fit AS/LS washers), drop the 3 mm cage in flat, and never press or hammer the needle complement.
Typical equipment & failure modes
Common applications
- light turntables, index plates and office-machine pivots
- two-wheeler gearbox selector and layshaft thrust faces
- compact drives where hardened washers replace a machined raceway shoulder
- automotive manual and automatic transmission thrust positions
Known failure patterns
- needle-row denting from a single hard particle trapped in the 2 mm section
- cage wear from rollers being dragged through unloaded zones under fluctuating thrust
- grease churning and overheating when a high-speed thrust position is over-packed
- rolling-contact fatigue spalling after the catalogue L10 life is exhausted
- instant raceway scoring when the assembly runs against a face below 58 HRC or with a rough finish
Selection pitfalls — read before you substitute
- On a 60 mm shaft the cage is only 3 mm thick — a shaft shoulder with a sharp edge or a 0.1 mm burr will catch and spin the cage instead of locating it.
- Match washers by the exact 60–85 mm track — a washer sized to the shaft alone leaves the needles overrunning its edge, which shears the cage.
- the 2,200 r/min reference speed is the thermal criterion under load, the 4,300 r/min limiting speed assumes hardened, ground, oiled faces; soft or dry faces drop the real ceiling drastically.
- TN polymer and stamped steel cages of the same code (AXK 6085) share envelopes and ratings; the choice is temperature and noise, not load.
- The AXK code supplies no washers: AXK 6085 arrives as the needle cage only, and a "bearing failure" on hard-faced tracks is usually a missing-AS-washer failure at ordering time.
- The 37.5/232 kN ratings and 33 g mass are SKF catalogue values transcribed from ch. 12.1 of PUB BU/P1 17000 (PDF table page 908); mounting data — Ea/Eb raceway diameters and the minimum load factor A — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
Why does an AXK assembly fail early?
Almost always the track: missing/undersized washers, hardness below 58 HRC, a sharp shoulder edge catching the cage, or contamination in the thin section. Rating 37.5 kN assumes all of these are correct.
Which dimensions does the AXK 6085 have?
A AXK 6085 measures 60 mm bore × 85 mm outside diameter × 3 mm width (2.362 × 3.346 × 0.118 in). From SKF catalogue PUB BU/P1 17000: dynamic C 37.5 kN, static C0 232 kN, fatigue limit Pu 28.5 kN, reference speed 2,200 r/min, limiting speed 4,300 r/min, mass about 33 g. The contact band runs Ea 65–Eb 83 mm; hardened washers or 58–64 HRC faces are required.
What does AXK 60/85 mean?
A needle roller and cage thrust assembly (ISO 3031) for a 60 mm inner track and 85 mm outer track, 3 mm thick; one-direction axial load, washers ordered separately.
What is the difference between AXK and AXW?
AXW pairs the AXK needle set with a washer carrying an integral centring spigot that locates in a housing register, keeping cage and washer concentric as one part; AXK is the bare cage-and-needle set needing two separate washers. The AXW still needs a separate LS/AS washer or hardened face on the opposite side.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies on 2026-09-27. Read our editorial & correction policy.