AXK3552 bearing: complete specifications & equivalents
The AXK3552 is a ISO 3031 radial bearing sized 35 x 52 x 2 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 35 mm |
| Outer diameter D | 52 mm |
| Width B | 2 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 16.6 kN |
| Basic static load rating C0 | 83 kN |
| Fatigue load limit Pu | 9.8 kN |
| Reference speed (thermal) | 3200 rpm |
| Limiting speed (mechanical) | 6300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 10 g |
| Manufacturer designation | AXK 3552 |
| Standard | ISO 3031 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & AXK-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 2.047 in |
| Width B | 0.079 in |
| ISO bore code | 52 |
| Radial section height (D−d)/2 | 8.5 mm |
| Smallest bore in AXK-series | 4 mm |
| Largest outer diameter in AXK-series | 200 mm |
| Width range across AXK-series | 2–5 mm |
| Bore position in AXK-series (smallest first) | 12 of 30 |
| Bore above smallest AXK-series size | 31 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| AXK3552 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; standard interchange — confirm clearance class and precision with the supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the AXK3552 model number is decoded
AXK 3552 gives thrust capacity in the height of a shim: 35 mm inner track, 52 mm outer track, only 2 mm thick, with needles held by the stamped steel cage for one-direction axial load. The designation AXK 3552 identifies a 2 mm needle thrust cage for the 35–52 mm track; the same diameters select the matching hardened washers, which is the usual ordering error to avoid. Washer selection is part of the bearing: too-soft faces rib within weeks even though the 16.6 kN rating is unchanged — the AXK code only supplies the rolling elements. Selection arithmetic: C 16.6 kN against C0 83 kN gives a C0/C ratio of 5.00 — thrust bearings are chosen on static rating and F_a/C0 more often than on L10 life. Mounting: harden and grind both mating faces to 58–64 HRC over the full Ea 39–Eb 51 mm band (or fit AS/LS washers), drop the 2 mm cage in flat, and never press or hammer the needle complement.
Typical equipment & failure modes
Common applications
- automotive manual and automatic transmission thrust positions
- torque converter and clutch release assemblies in passenger cars
- small gearbox gears that need a 2 mm thrust shim between a shaft and face
- light turntables, index plates and office-machine pivots
Known failure patterns
- edge loading across the needle crowns when the mating faces are not square to the shaft
- smearing at roller-raceway contacts during unloaded startup before the oil film or preload is established
- abrasive paste forming as dust bypasses the housing seals into the open washer set
- rolling-contact fatigue spalling after the catalogue L10 life is exhausted
- needle-row denting from a single hard particle trapped in the 2 mm section
Selection pitfalls — read before you substitute
- On a 35 mm shaft the cage is only 2 mm thick — a shaft shoulder with a sharp edge or a 0.1 mm burr will catch and spin the cage instead of locating it.
- the 3,200 r/min reference speed is the thermal criterion under load, the 6,300 r/min limiting speed assumes hardened, ground, oiled faces; soft or dry faces drop the real ceiling drastically.
- The 16.6 kN rating is real only at 58–64 HRC face hardness; visual inspection cannot tell a 45 HRC washer from a 60 HRC one — order certified washers.
- Match washers by the exact 35–52 mm track — a washer sized to the shaft alone leaves the needles overrunning its edge, which shears the cage.
- The AXK code supplies no washers: AXK 3552 arrives as the needle cage only, and a "bearing failure" on hard-faced tracks is usually a missing-AS-washer failure at ordering time.
- The 16.6/83 kN ratings and 10 g mass are SKF catalogue values transcribed from ch. 12.1 of PUB BU/P1 17000 (PDF table page 908); mounting data — Ea/Eb raceway diameters and the minimum load factor A — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
What minimum hardness do the mating faces need?
58–64 HRC with a ground raceway finish. A softer face looks fine after assembly but the needles rib and score it within weeks despite the 16.6 kN catalogue rating — order certified washers if the shaft/housing cannot be heat treated.
How is an AXK thrust assembly mounted?
Harden or washer-face both tracks across Ea 39–Eb 51 mm, keep faces parallel, locate the cage concentrically against a shoulder or register, grease the needles so they stay pocketed, and never press through them.
What are the dimensions and ratings of the AXK 3552?
A AXK 3552 measures 35 mm bore × 52 mm outside diameter × 2 mm width (1.378 × 2.047 × 0.079 in). From SKF catalogue PUB BU/P1 17000: dynamic C 16.6 kN, static C0 83 kN, fatigue limit Pu 9.8 kN, reference speed 3,200 r/min, limiting speed 6,300 r/min, mass about 10 g. The contact band runs Ea 39–Eb 51 mm; hardened washers or 58–64 HRC faces are required.
Does the AXK 3552 include washers?
No. AXK is the needle roller and cage thrust assembly only; hardened AS/LS washers or shaft/housing faces at 58–64 HRC, ground over the Ea 39–Eb 51 mm band, supply the two raceways.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 12.1 needle roller and cage thrust assemblies on 2026-09-27. Read our editorial & correction policy.