63010-2RS bearing: complete specifications & equivalents

The 63010-2RS is a ISO 15 radial bearing sized 50 x 80 x 23 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 80 mm d = 50 B = 23 mm side section front view
Principal dimensions: bore d 50 mm, outer diameter D 80 mm, width B 23 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 50 mm
Outer diameter D 80 mm
Width B 23 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 21.6 kN
Basic static load rating C0 15.6 kN
Fatigue load limit Pu 0.71 kN
Limiting speed (mechanical) 5000 rpm
Operating temperature -40 to +120 °C
Mass 380 g
Manufacturer designation 63010-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 63000-series range

Bore d1.969 in
Outer diameter D3.15 in
Width B0.906 in
ISO bore code10
Radial section height (D−d)/215 mm
Smallest bore in 63000-series10 mm
Largest outer diameter in 63000-series80 mm
Width range across 63000-series12–23 mm
Bore position in 63000-series (smallest first)11 of 11
Bore above smallest 63000-series size40 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 63010-2RS model number is decoded

The 63000-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 63010 carries code 10 = 50 mm (code × 5). The envelope is 50×80×23 mm (1.969×3.15×0.906 in) with a 15.0 mm radial section height, C 21.6 kN, C0 15.6 kN and Pu 0.71 kN. SKF catalogues the sealed execution as 63010-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 5000 r/min, catalogue mass 380 g.

Typical equipment & failure modes

Common applications

  • centrifugal and positive-displacement pumps
  • material-handling equipment
  • industrial fans
  • compressor drives

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • cage damage from running beyond the limiting speed
  • raceway smearing under marginal lubrication at start-up

Selection pitfalls — read before you substitute

  • At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 63010-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Contact seals make 63010-2RS slower than the open 63010 (limiting 5000 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 63010-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Catalogue ratings for 63010-2RS (C 21.6 kN, C0 15.6 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.

Frequently asked questions

What are the dimensions of 63010-2RS?

The SKF 63010-2RS1 measures 50 mm bore × 80 mm OD × 23 mm width (1.969 × 3.15 × 0.906 in), mass about 380 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 63010 work?

The final two digits of 63010 are bore code 10, multiplied by 5 to give 50 mm.

What is the speed rating of 63010-2RS?

SKF publishes only the 5000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern.

What is the difference between 63010-2RS and a same-bore 62-series bearing?

Section height differs: 63010-2RS has a 15 mm radial section and C 21.6 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Which fits should I use for 63010-2RS?

With a rotating inner ring use roughly k5 on the shaft and H7 in the 80 mm housing; reverse the interference if the outer ring rotates.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.