63005-2RS bearing: complete specifications & equivalents

The 63005-2RS is a ISO 15 radial bearing sized 25 x 47 x 16 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 47 mm d = 25 B = 16 mm side section front view
Principal dimensions: bore d 25 mm, outer diameter D 47 mm, width B 16 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 25 mm
Outer diameter D 47 mm
Width B 16 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 11.2 kN
Basic static load rating C0 6.55 kN
Fatigue load limit Pu 0.275 kN
Limiting speed (mechanical) 9500 rpm
Operating temperature -40 to +120 °C
Mass 110 g
Manufacturer designation 63005-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 63000-series range

Bore d0.984 in
Outer diameter D1.85 in
Width B0.63 in
ISO bore code05
Radial section height (D−d)/211 mm
Smallest bore in 63000-series10 mm
Largest outer diameter in 63000-series80 mm
Width range across 63000-series12–23 mm
Bore position in 63000-series (smallest first)6 of 11
Bore above smallest 63000-series size15 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 63005-2RS model number is decoded

The 63000-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 63005 carries code 05 = 25 mm (code × 5). The envelope is 25×47×16 mm (0.984×1.85×0.63 in) with a 11.0 mm radial section height, C 11.2 kN, C0 6.55 kN and Pu 0.275 kN. SKF catalogues the sealed execution as 63005-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 9500 r/min, catalogue mass 110 g.

Typical equipment & failure modes

Common applications

  • electric motors
  • centrifugal pumps
  • small gearboxes
  • conveyor drives

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • electrical pitting in VFD-driven motors without shaft grounding
  • edge loading from shaft deflection or housing misalignment

Selection pitfalls — read before you substitute

  • Assign interference to the rotating ring: on a conventional shaft-mounted 25 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 63005-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Contact seals make 63005-2RS slower than the open 63005 (limiting 9500 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 63005-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • Mount by heating the inner ring (max 120 °C) — driving 63005-2RS home through the outer ring or balls brinells the raceways.
  • The fatigue load limit is 0.275 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.
  • A replacement 63005 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.

Frequently asked questions

What are the dimensions of 63005-2RS?

The SKF 63005-2RS1 measures 25 mm bore × 47 mm OD × 16 mm width (0.984 × 1.85 × 0.63 in), mass about 110 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 63005 work?

The final two digits of 63005 are bore code 05, multiplied by 5 to give 25 mm.

What internal clearance does 63005-2RS have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 63005-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 63005-2RS take?

Catalogue values for 63005-2RS1: dynamic C 11.2 kN, static C0 6.55 kN, fatigue limit Pu 0.275 kN. Use C in life calculation and C0 for static checks at 25 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.