6330-M (brass cage) bearing: complete specifications & equivalents

The 6330-M is a ISO 15 radial bearing sized 150 x 320 x 65 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 320 mm d = 150 B = 65 mm side section front view
Principal dimensions: bore d 150 mm, outer diameter D 320 mm, width B 65 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 150 mm
Outer diameter D 320 mm
Width B 65 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 276 kN
Basic static load rating C0 285 kN
Fatigue load limit Pu 7.8 kN
Reference speed (thermal) 4300 rpm
Limiting speed (mechanical) 4000 rpm
Operating temperature -40 to +120 °C
Mass 25500 g
Manufacturer designation 6330 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6300-series range

Bore d5.906 in
Outer diameter D12.598 in
Width B2.559 in
ISO bore code30
Radial section height (D−d)/285 mm
Smallest bore in 6300-series2 mm
Largest outer diameter in 6300-series500 mm
Width range across 6300-series3–95 mm
Bore position in 6300-series (smallest first)33 of 40
Bore above smallest 6300-series size148 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6330-ZZ NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6330ZZ on the same 150×320×65 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6330-NSK NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6330 on the same 150×320×65 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6330-NTN NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6330 on the same 150×320×65 mm envelope, but catalogue C/C0 differ (276/285 kN vs 305/284 kN) — envelope interchange only after a load check.
6330 SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6330 (open arrangement) shares the 150×320×65 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6330-M model number is decoded

In the 6300-series, the last two digits encode the bore: 6330 carries code 30 = 150 mm (code × 5). The envelope is 150×320×65 mm (5.906×12.598×2.559 in) with a 85.0 mm radial section height, C 276 kN, C0 285 kN and Pu 7.8 kN. The open 6330 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 4000 r/min, catalogue mass 25500 g.

Typical equipment & failure modes

Common applications

  • large industrial gearboxes
  • heavy conveyor drives
  • hoists and winches
  • industrial fans and blowers

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Do not preload 6330-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Fillet radii must clear the 6330-M chamfer so the 65 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • The M suffix on 6330-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 25500 g quoted mass includes the heavier cage.
  • Open 6330-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6330-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Catalogue ratings for 6330-M (C 276 kN, C0 285 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 6330-M?

The SKF 6330 M measures 150 mm bore × 320 mm OD × 65 mm width (5.906 × 12.598 × 2.559 in), mass about 25500 g. It is open, with no shields or seals.

How does the bore code in 6330 work?

The final two digits of 6330 are bore code 30, multiplied by 5 to give 150 mm.

What internal clearance does 6330-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6330-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 6330-M take?

Catalogue values for 6330 M: dynamic C 276 kN, static C0 285 kN, fatigue limit Pu 7.8 kN. Use C in life calculation and C0 for static checks at 150 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.