62206-2RS bearing: complete specifications & equivalents

The 62206-2RS is a ISO 15 radial bearing sized 30 x 62 x 20 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 62 mm d = 30 B = 20 mm side section front view
Principal dimensions: bore d 30 mm, outer diameter D 62 mm, width B 20 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 30 mm
Outer diameter D 62 mm
Width B 20 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 19.5 kN
Basic static load rating C0 11.2 kN
Fatigue load limit Pu 0.475 kN
Limiting speed (mechanical) 7500 rpm
Operating temperature -40 to +120 °C
Mass 250 g
Manufacturer designation 62206-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 62200-series range

Bore d1.181 in
Outer diameter D2.441 in
Width B0.787 in
ISO bore code06
Radial section height (D−d)/216 mm
Smallest bore in 62200-series10 mm
Largest outer diameter in 62200-series125 mm
Width range across 62200-series14–31 mm
Bore position in 62200-series (smallest first)7 of 15
Bore above smallest 62200-series size20 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
4206-ATN9 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 30×62×20 mm envelope as SKF 4206 ATN9, but catalogue C/C0 differ (19.5/11.2 kN vs 26/20.8 kN) — envelope match only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 62206-2RS model number is decoded

The 62200-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 62206 carries code 06 = 30 mm (code × 5). The envelope is 30×62×20 mm (1.181×2.441×0.787 in) with a 16.0 mm radial section height, C 19.5 kN, C0 11.2 kN and Pu 0.475 kN. SKF catalogues the sealed execution as 62206-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 7500 r/min, catalogue mass 250 g.

Typical equipment & failure modes

Common applications

  • garden machinery
  • textile machines
  • electric motors
  • centrifugal pumps

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded
  • brinelling from static overload or hammer blows during mounting

Selection pitfalls — read before you substitute

  • Fillet radii must clear the 62206-2RS chamfer so the 20 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Catalogue ratings for 62206-2RS (C 19.5 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Contact seals make 62206-2RS slower than the open 62206 (limiting 7500 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 62206-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • Catalogue ratings for 62206-2RS (C 19.5 kN, C0 11.2 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Mount by heating the inner ring (max 120 °C) — driving 62206-2RS home through the outer ring or balls brinells the raceways.
  • A replacement 62206 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.

Frequently asked questions

What are the dimensions of 62206-2RS?

The SKF 62206-2RS1 measures 30 mm bore × 62 mm OD × 20 mm width (1.181 × 2.441 × 0.787 in), mass about 250 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 62206 work?

The final two digits of 62206 are bore code 06, multiplied by 5 to give 30 mm.

What internal clearance does 62206-2RS have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 62206-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 62206-2RS take?

Catalogue values for 62206-2RS1: dynamic C 19.5 kN, static C0 11.2 kN, fatigue limit Pu 0.475 kN. Use C in life calculation and C0 for static checks at 30 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.