6260-M bearing: complete specifications & equivalents

The 6260-M is a ISO 15 radial bearing sized 300 x 540 x 85 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 540 mm d = 300 B = 85 mm side section front view
Principal dimensions: bore d 300 mm, outer diameter D 540 mm, width B 85 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 300 mm
Outer diameter D 540 mm
Width B 85 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 462 kN
Basic static load rating C0 670 kN
Fatigue load limit Pu 13.7 kN
Reference speed (thermal) 2400 rpm
Limiting speed (mechanical) 2000 rpm
Operating temperature -40 to +120 °C
Mass 88500 g
Manufacturer designation 6260 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6200-series range

Bore d11.811 in
Outer diameter D21.26 in
Width B3.346 in
ISO bore code60
Radial section height (D−d)/2120 mm
Smallest bore in 6200-series3 mm
Largest outer diameter in 6200-series540 mm
Width range across 6200-series2.5–85 mm
Bore position in 6200-series (smallest first)45 of 45
Bore above smallest 6200-series size297 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 6260-M model number is decoded

In the 6200-series, the last two digits encode the bore: 6260 carries code 60 = 300 mm (code × 5). The envelope is 300×540×85 mm (11.811×21.26×3.346 in) with a 120.0 mm radial section height, C 462 kN, C0 670 kN and Pu 13.7 kN. The open 6260 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 2000 r/min, catalogue mass 88500 g.

Typical equipment & failure modes

Common applications

  • mill and kiln auxiliaries
  • pulp and paper machinery
  • marine deck machinery
  • crusher auxiliary drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • edge loading from shaft deflection or housing misalignment
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded

Selection pitfalls — read before you substitute

  • Catalogue ratings for 6260-M (C 462 kN, C0 670 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Fillet radii must clear the 6260-M chamfer so the 85 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • The M suffix on 6260-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 88500 g quoted mass includes the heavier cage.
  • Open 6260-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6260-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Do not preload 6260-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 6260-M?

The SKF 6260 M measures 300 mm bore × 540 mm OD × 85 mm width (11.811 × 21.26 × 3.346 in), mass about 88500 g. It is open, with no shields or seals.

How does the bore code in 6260 work?

The final two digits of 6260 are bore code 60, multiplied by 5 to give 300 mm.

What load can 6260-M take?

Catalogue values for 6260 M: dynamic C 462 kN, static C0 670 kN, fatigue limit Pu 13.7 kN. Use C in life calculation and C0 for static checks at 300 mm bore.

What is the speed rating of 6260-M?

SKF lists a 2400 r/min thermal reference speed and a 2000 r/min mechanical limiting speed for 6260 M; real limits also depend on lubrication and fits.

What is the difference between 6260-M and a same-bore 62-series bearing?

Section height differs: 6260-M has a 120 mm radial section and C 462 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.