6220-M (brass cage) bearing: complete specifications & equivalents

The 6220-M is a ISO 15 radial bearing sized 100 x 180 x 34 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 180 mm d = 100 B = 34 mm side section front view
Principal dimensions: bore d 100 mm, outer diameter D 180 mm, width B 34 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 100 mm
Outer diameter D 180 mm
Width B 34 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 127 kN
Basic static load rating C0 93 kN
Fatigue load limit Pu 3.35 kN
Reference speed (thermal) 7500 rpm
Limiting speed (mechanical) 7000 rpm
Operating temperature -40 to +120 °C
Mass 3800 g
Manufacturer designation 6220 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6200-series range

Bore d3.937 in
Outer diameter D7.087 in
Width B1.339 in
ISO bore code20
Radial section height (D−d)/240 mm
Smallest bore in 6200-series3 mm
Largest outer diameter in 6200-series540 mm
Width range across 6200-series2.5–85 mm
Bore position in 6200-series (smallest first)29 of 45
Bore above smallest 6200-series size97 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6220-2RS-NSK NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6220DDU on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-RSR NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6220VV on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-ZZ-NSK NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6220ZZ on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-NSK NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6220 on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-NTN NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6220 on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-2RS-NTN NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6220LLU on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-RSR-NTN NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6220LLB on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6220-ZZ-NTN NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6220ZZ on the same 100×180×34 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
220 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 100×180×34 mm envelope as SKF 220, but catalogue C/C0 differ (127/93 kN vs 134/140 kN) — envelope match only after a load check.
220-ZZ SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 100×180×34 mm envelope as SKF 220-2Z, but catalogue C/C0 differ (127/93 kN vs 134/140 kN) — envelope match only after a load check.
6220 SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6220 (open arrangement) shares the 100×180×34 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.
6220-ZZ SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6220-2Z (two non-contact shields) shares the 100×180×34 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.
6220-2RS SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6220-2RS1 (two contact elastomer seals) shares the 100×180×34 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6220-M model number is decoded

In the 6200-series, the last two digits encode the bore: 6220 carries code 20 = 100 mm (code × 5). The envelope is 100×180×34 mm (3.937×7.087×1.339 in) with a 40.0 mm radial section height, C 127 kN, C0 93 kN and Pu 3.35 kN. The open 6220 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 7000 r/min, catalogue mass 3800 g.

Typical equipment & failure modes

Common applications

  • centrifugal and positive-displacement pumps
  • material-handling equipment
  • industrial fans
  • compressor drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • fretting corrosion on a creeping shaft or housing seat
  • cage damage from running beyond the limiting speed

Selection pitfalls — read before you substitute

  • Mount by heating the inner ring (max 120 °C) — driving 6220-M home through the outer ring or balls brinells the raceways.
  • Mount by heating the inner ring (max 120 °C) — driving 6220-M home through the outer ring or balls brinells the raceways.
  • The M suffix on 6220-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 3800 g quoted mass includes the heavier cage.
  • Open 6220-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6220-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Assign interference to the rotating ring: on a conventional shaft-mounted 100 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • A replacement 6220 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • Where two 6220 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.

Frequently asked questions

What are the dimensions of 6220-M?

The SKF 6220 M measures 100 mm bore × 180 mm OD × 34 mm width (3.937 × 7.087 × 1.339 in), mass about 3800 g. It is open, with no shields or seals.

How does the bore code in 6220 work?

The final two digits of 6220 are bore code 20, multiplied by 5 to give 100 mm.

How heavy is 6220-M?

Catalogue mass is 3800 g for 6220 M; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 6220-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6220-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.