61934-MA bearing: complete specifications & equivalents

The 61934-MA is a ISO 15 radial bearing sized 170 x 230 x 28 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 230 mm d = 170 B = 28 mm side section front view
Principal dimensions: bore d 170 mm, outer diameter D 230 mm, width B 28 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 170 mm
Outer diameter D 230 mm
Width B 28 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 93.6 kN
Basic static load rating C0 106 kN
Fatigue load limit Pu 3.15 kN
Reference speed (thermal) 5600 rpm
Limiting speed (mechanical) 4800 rpm
Operating temperature -40 to +120 °C
Mass 3350 g
Manufacturer designation 61934 MA
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 61900-series range

Bore d6.693 in
Outer diameter D9.055 in
Width B1.102 in
ISO bore code34
Radial section height (D−d)/230 mm
Smallest bore in 61900-series3 mm
Largest outer diameter in 61900-series1120 mm
Width range across 61900-series3–118 mm
Bore position in 61900-series (smallest first)36 of 63
Bore above smallest 61900-series size167 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
61934-FAG FAG partial
Main dimensions match; tolerances, seals or internal clearance differ.
FAG bearing FAG 61934 on the same 170×230×28 mm envelope, but catalogue C/C0 differ (93.6/106 kN vs 109/114 kN) — envelope interchange only after a load check.
61934-ZZ NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6934ZZ on the same 170×230×28 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
61934 NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6934 on the same 170×230×28 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
61934-NTN NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6934 on the same 170×230×28 mm envelope, but catalogue C/C0 differ (93.6/106 kN vs 95/95.5 kN) — envelope interchange only after a load check.
61934-ZZ-NTN NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6934ZZ on the same 170×230×28 mm envelope, but catalogue C/C0 differ (93.6/106 kN vs 95/95.5 kN) — envelope interchange only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61934-MA model number is decoded

In the 61900-series, the last two digits encode the bore: 61934 carries code 34 = 170 mm (code × 5). The envelope is 170×230×28 mm (6.693×9.055×1.102 in) with a 30.0 mm radial section height, C 93.6 kN, C0 106 kN and Pu 3.15 kN. The open 61934 MA carries no shields or seals and relies on application lubrication and external sealing. The MA suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 4800 r/min, catalogue mass 3350 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • textile and packaging machinery
  • slew and indexing drives
  • large industrial gearboxes
  • heavy conveyor drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • fretting corrosion on a creeping shaft or housing seat
  • cage damage from running beyond the limiting speed

Selection pitfalls — read before you substitute

  • At 170 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Catalogue ratings for 61934-MA (C 93.6 kN, C0 106 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • The MA suffix on 61934-MA denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 3350 g quoted mass includes the heavier cage.
  • Open 61934-MA needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 61934-MA; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Assign interference to the rotating ring: on a conventional shaft-mounted 170 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • A replacement 61934 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.

Frequently asked questions

What are the dimensions of 61934-MA?

The SKF 61934 MA measures 170 mm bore × 230 mm OD × 28 mm width (6.693 × 9.055 × 1.102 in), mass about 3350 g. It is open, with no shields or seals.

How does the bore code in 61934 work?

The final two digits of 61934 are bore code 34, multiplied by 5 to give 170 mm.

How heavy is 61934-MA?

Catalogue mass is 3350 g for 61934 MA; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 61934-MA have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 61934-MA be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.