618-9 bearing: complete specifications & equivalents

The 618-9 is a ISO 15 radial bearing sized 9 x 17 x 4 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 17 mm d = 9 B = 4 mm side section front view
Principal dimensions: bore d 9 mm, outer diameter D 17 mm, width B 4 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 9 mm
Outer diameter D 17 mm
Width B 4 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 0.871 kN
Basic static load rating C0 0.34 kN
Fatigue load limit Pu 0.014 kN
Reference speed (thermal) 85000 rpm
Limiting speed (mechanical) 53000 rpm
Operating temperature -40 to +120 °C
Mass 3.4 g
Manufacturer designation 618/9
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 61800-series range

Bore d0.354 in
Outer diameter D0.669 in
Width B0.157 in
ISO bore code—
Radial section height (D−d)/24 mm
Smallest bore in 61800-series1 mm
Largest outer diameter in 61800-series1820 mm
Width range across 61800-series1–140 mm
Bore position in 61800-series (smallest first)10 of 74
Bore above smallest 61800-series size8 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
W618-9 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 9×17×4 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (0.871/0.34 kN vs 0.761/0.335 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 618-9 model number is decoded

In the miniature 61800-series, the bore is written directly after the slash as 9 mm (bores below 10 mm use the slash spelling). The envelope is 9×17×4 mm (0.354×0.669×0.157 in) with a 4.0 mm radial section height, C 0.871 kN, C0 0.34 kN and Pu 0.014 kN. The open 618/9 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 53000 r/min, catalogue mass 3.4 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • clutch and transmission assemblies
  • robotics and automation joints
  • lay shafts and idler shafts
  • textile and packaging machinery

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • cage damage from running beyond the limiting speed
  • raceway smearing under marginal lubrication at start-up

Selection pitfalls — read before you substitute

  • Assign interference to the rotating ring: on a conventional shaft-mounted 9 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
  • Catalogue ratings for 618-9 (C 0.871 kN, C0 0.34 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Open 618-9 needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 618-9; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Catalogue ratings for 618-9 (C 0.871 kN, C0 0.34 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Mount by heating the inner ring (max 120 °C) — driving 618-9 home through the outer ring or balls brinells the raceways.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.

Frequently asked questions

What are the dimensions of 618-9?

The SKF 618/9 measures 9 mm bore × 17 mm OD × 4 mm width (0.354 × 0.669 × 0.157 in), mass about 3.4 g. It is open, with no shields or seals.

Why is there a slash in the designation 618/9?

The slash writes a bore that falls outside the two-digit code table: 618/9 means 9 mm bore. The site slug 618-9 replaces the slash with a hyphen.

What internal clearance does 618-9 have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 618-9 be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 618-9 take?

Catalogue values for 618/9: dynamic C 0.871 kN, static C0 0.34 kN, fatigue limit Pu 0.014 kN. Use C in life calculation and C0 for static checks at 9 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.