6084-M bearing: complete specifications & equivalents

The 6084-M is a ISO 15 radial bearing sized 420 x 620 x 90 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 620 mm d = 420 B = 90 mm side section front view
Principal dimensions: bore d 420 mm, outer diameter D 620 mm, width B 90 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 420 mm
Outer diameter D 620 mm
Width B 90 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 507 kN
Basic static load rating C0 880 kN
Fatigue load limit Pu 16.3 kN
Reference speed (thermal) 2000 rpm
Limiting speed (mechanical) 1600 rpm
Operating temperature -40 to +120 °C
Mass 91500 g
Manufacturer designation 6084 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d16.535 in
Outer diameter D24.409 in
Width B3.543 in
ISO bore code84
Radial section height (D−d)/2100 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)49 of 61
Bore above smallest 6000-series size416 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6084 NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6084 on the same 420×620×90 mm envelope, but catalogue C/C0 differ (507/880 kN vs 590/895 kN) — envelope interchange only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6084-M model number is decoded

In the 6000-series, the last two digits encode the bore: 6084 carries code 84 = 420 mm (code × 5). The envelope is 420×620×90 mm (16.535×24.409×3.543 in) with a 100.0 mm radial section height, C 507 kN, C0 880 kN and Pu 16.3 kN. The open 6084 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 1600 r/min, catalogue mass 91500 g.

Typical equipment & failure modes

Common applications

  • mill and kiln auxiliaries
  • pulp and paper machinery
  • marine deck machinery
  • crusher auxiliary drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • edge loading from shaft deflection or housing misalignment
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded

Selection pitfalls — read before you substitute

  • Fillet radii must clear the 6084-M chamfer so the 90 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Do not preload 6084-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The M suffix on 6084-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 91500 g quoted mass includes the heavier cage.
  • Open 6084-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6084-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • The fatigue load limit is 16.3 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.

Frequently asked questions

What are the dimensions of 6084-M?

The SKF 6084 M measures 420 mm bore × 620 mm OD × 90 mm width (16.535 × 24.409 × 3.543 in), mass about 91500 g. It is open, with no shields or seals.

How does the bore code in 6084 work?

The final two digits of 6084 are bore code 84, multiplied by 5 to give 420 mm.

How heavy is 6084-M?

Catalogue mass is 91500 g for 6084 M; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 6084-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6084-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.