6076-M bearing: complete specifications & equivalents

The 6076-M is a ISO 15 radial bearing sized 380 x 560 x 82 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 560 mm d = 380 B = 82 mm side section front view
Principal dimensions: bore d 380 mm, outer diameter D 560 mm, width B 82 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 380 mm
Outer diameter D 560 mm
Width B 82 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 436 kN
Basic static load rating C0 695 kN
Fatigue load limit Pu 13.7 kN
Reference speed (thermal) 2200 rpm
Limiting speed (mechanical) 1800 rpm
Operating temperature -40 to +120 °C
Mass 70500 g
Manufacturer designation 6076 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d14.961 in
Outer diameter D22.047 in
Width B3.228 in
ISO bore code76
Radial section height (D−d)/290 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)47 of 61
Bore above smallest 6000-series size376 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6076 NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6076 on the same 380×560×82 mm envelope, but catalogue C/C0 differ (436/695 kN vs 505/725 kN) — envelope interchange only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6076-M model number is decoded

In the 6000-series, the last two digits encode the bore: 6076 carries code 76 = 380 mm (code × 5). The envelope is 380×560×82 mm (14.961×22.047×3.228 in) with a 90.0 mm radial section height, C 436 kN, C0 695 kN and Pu 13.7 kN. The open 6076 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 1800 r/min, catalogue mass 70500 g.

Typical equipment & failure modes

Common applications

  • slew and indexing drives
  • large industrial gearboxes
  • heavy conveyor drives
  • hoists and winches

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • false brinelling from vibration while the shaft stands idle
  • fretting corrosion on a creeping shaft or housing seat

Selection pitfalls — read before you substitute

  • Clearance suffixes follow the seal code in the designation stack (e.g. 6076-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Do not preload 6076-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The M suffix on 6076-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 70500 g quoted mass includes the heavier cage.
  • Open 6076-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6076-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • At 380 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Where two 6076 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 6076-M?

The SKF 6076 M measures 380 mm bore × 560 mm OD × 82 mm width (14.961 × 22.047 × 3.228 in), mass about 70500 g. It is open, with no shields or seals.

How does the bore code in 6076 work?

The final two digits of 6076 are bore code 76, multiplied by 5 to give 380 mm.

How long can a greased 6076-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 6076-M take?

Catalogue values for 6076 M: dynamic C 436 kN, static C0 695 kN, fatigue limit Pu 13.7 kN. Use C in life calculation and C0 for static checks at 380 mm bore.

What is the speed rating of 6076-M?

SKF lists a 2200 r/min thermal reference speed and a 1800 r/min mechanical limiting speed for 6076 M; real limits also depend on lubrication and fits.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.