6064-M bearing: complete specifications & equivalents

The 6064-M is a ISO 15 radial bearing sized 320 x 480 x 74 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 480 mm d = 320 B = 74 mm side section front view
Principal dimensions: bore d 320 mm, outer diameter D 480 mm, width B 74 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 320 mm
Outer diameter D 480 mm
Width B 74 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 371 kN
Basic static load rating C0 540 kN
Fatigue load limit Pu 11.4 kN
Reference speed (thermal) 2600 rpm
Limiting speed (mechanical) 2200 rpm
Operating temperature -40 to +120 °C
Mass 46000 g
Manufacturer designation 6064 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d12.598 in
Outer diameter D18.898 in
Width B2.913 in
ISO bore code64
Radial section height (D−d)/280 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)44 of 61
Bore above smallest 6000-series size316 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6064 NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6064 on the same 320×480×74 mm envelope, but catalogue C/C0 differ (371/540 kN vs 410/530 kN) — envelope interchange only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6064-M model number is decoded

In the 6000-series, the last two digits encode the bore: 6064 carries code 64 = 320 mm (code × 5). The envelope is 320×480×74 mm (12.598×18.898×2.913 in) with a 80.0 mm radial section height, C 371 kN, C0 540 kN and Pu 11.4 kN. The open 6064 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 2200 r/min, catalogue mass 46000 g.

Typical equipment & failure modes

Common applications

  • space-constrained gearboxes
  • clutch and transmission assemblies
  • robotics and automation joints
  • lay shafts and idler shafts

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Clearance suffixes follow the seal code in the designation stack (e.g. 6064-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Do not preload 6064-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The M suffix on 6064-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 46000 g quoted mass includes the heavier cage.
  • Open 6064-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6064-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Deep-groove geometry tolerates only minutes of misalignment; if the 480 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 6064-M.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.
  • A replacement 6064 should go onto inspected seats only: SKF mounting guidance calls for clean, burr-free journals within tolerance, since a large share of early failures traces back to damaged or worn seats.

Frequently asked questions

What are the dimensions of 6064-M?

The SKF 6064 M measures 320 mm bore × 480 mm OD × 74 mm width (12.598 × 18.898 × 2.913 in), mass about 46000 g. It is open, with no shields or seals.

How does the bore code in 6064 work?

The final two digits of 6064 are bore code 64, multiplied by 5 to give 320 mm.

How heavy is 6064-M?

Catalogue mass is 46000 g for 6064 M; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 6064-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6064-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.