6044-M (brass cage) bearing: complete specifications & equivalents

The 6044-M is a ISO 15 radial bearing sized 220 x 340 x 56 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 340 mm d = 220 B = 56 mm side section front view
Principal dimensions: bore d 220 mm, outer diameter D 340 mm, width B 56 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 220 mm
Outer diameter D 340 mm
Width B 56 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 247 kN
Basic static load rating C0 290 kN
Fatigue load limit Pu 7.35 kN
Reference speed (thermal) 4000 rpm
Limiting speed (mechanical) 3200 rpm
Operating temperature -40 to +120 °C
Mass 18500 g
Manufacturer designation 6044 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6000-series range

Bore d8.661 in
Outer diameter D13.386 in
Width B2.205 in
ISO bore code44
Radial section height (D−d)/260 mm
Smallest bore in 6000-series4 mm
Largest outer diameter in 6000-series1150 mm
Width range across 6000-series4–155 mm
Bore position in 6000-series (smallest first)39 of 61
Bore above smallest 6000-series size216 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6044-ZZ NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6044ZZ on the same 220×340×56 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6044-NSK NSK full
Dimensions and internal design equivalent — standard interchange.
NSK counterpart NSK 6044 on the same 220×340×56 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6044-NTN NTN full
Dimensions and internal design equivalent — standard interchange.
NTN counterpart 6044 on the same 220×340×56 mm envelope with ratings within 10 % — interchange after checking seal, cage and precision details on both pages.
6044 SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6044 (open arrangement) shares the 220×340×56 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6044-M model number is decoded

In the 6000-series, the last two digits encode the bore: 6044 carries code 44 = 220 mm (code × 5). The envelope is 220×340×56 mm (8.661×13.386×2.205 in) with a 60.0 mm radial section height, C 247 kN, C0 290 kN and Pu 7.35 kN. The open 6044 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 3200 r/min, catalogue mass 18500 g.

Typical equipment & failure modes

Common applications

  • marine deck machinery
  • crusher auxiliary drives
  • large industrial gearboxes
  • heavy conveyor drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • fretting corrosion on a creeping shaft or housing seat
  • cage damage from running beyond the limiting speed

Selection pitfalls — read before you substitute

  • Do not preload 6044-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Fillet radii must clear the 6044-M chamfer so the 56 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • The M suffix on 6044-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 18500 g quoted mass includes the heavier cage.
  • Open 6044-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6044-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Do not preload 6044-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 6044-M?

The SKF 6044 M measures 220 mm bore × 340 mm OD × 56 mm width (8.661 × 13.386 × 2.205 in), mass about 18500 g. It is open, with no shields or seals.

How does the bore code in 6044 work?

The final two digits of 6044 are bore code 44, multiplied by 5 to give 220 mm.

How heavy is 6044-M?

Catalogue mass is 18500 g for 6044 M; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 6044-M have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 6044-M be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.